Unusual Effect of α-olefins as Chain Transfer Agents in Ethylene Polymerization over the Catalyst with Nonsymmetrical Bis(imino)pyridine Complex of Fe(II) and Modified Methylalumoxane (MMAO) Cocatalyst.

Ethylene polymerization with bis(imino)pyridlyiron precatalysts generally produces linear polyethylene (PE) even with the presence of α-olefins because α-olefins are not incorporated into polymeric products. Interestingly, α-olefins, such as hexene-1 or butene-1, have been found to act as effective chain transfer agents in the ethylene polymerization promoted by nonsymmetrical bis(imino)pyridyliron complexes with modified methylalumoxane (MMAO), resulting in higher catalytic activities with higher amounts of polymers with lower molecular weights, and, more importantly, narrower molecular weight distributions of the resultant polyethylenes (PE). This phenomenon confirms the assistance of α-olefins in the chain-termination reaction of iron-initiated polymerization and regeneration of the active species for further polymerization. Besides higher activities of the catalytic system, the formation of linear PE with trans-vinylene terminal groups and lower molecular weights are explained. The observation will provide a new pathway for enhancing catalytic activity and improving the quality of polyethylenes obtained by regulation of molecular weights and molecular weight distribution.

Effect of Mono- and Multichlorinated Organic Compounds-Chlorocyclohexane and Hexachloro-p-xylene-On the Catalytic Properties of Titanium-Magnesium Catalysts in the Homo- and Copolymerization of Ethylene with 1-Hexene.

Ethylene polymerization and ethylene/1-hexene copolymerization over the titanium-magnesium catalytic system in the presence of chlorocyclohexane (CHC) and hexachloro-p-xylene (HCPX) has been studied. Modification of TMC with chlorocyclohexane and hexachloro-p-xylene increased catalyst activity severalfold for both ethylene polymerization and ethylene/1-hexene copolymerization. The key kinetic regularities of ethylene homopolymerization and ethylene/1-hexene copolymerization in the presence of CHC and HCPX were determined, and the copolymerization constants were measured. Molecular characteristics and the copolymer composition were determined for the synthesized samples of ethylene homopolymers and ethylene/hexene copolymers. Modification of the titanium-magnesium catalyst with chlorinated organic compounds reduced 1-hexene content in the copolymer; polymerization was sensitive to 1-hexene as a regulator of polymer molecular weight. The potential mode of action of chlorinated organic modifiers on catalytic properties of titanium-magnesium catalyst is discussed.

Low-Temperature Mechanical Properties of High-Density and Low-Density Polyethylene and Their Blends.

Low-temperature properties of high-density polyethylene (HDPE), low-density polyethylene (LDPE), linear low-density polyethylene (LLDPE), and their blends were studied. The analyzed low-temperature mechanical properties involve the deformation resistance and impact strength characteristics. HDPE is a bimodal ethylene/1-hexene copolymer; LDPE is a branched ethylene homopolymer containing short-chain branches of different length; LLDPE is a binary ethylene/1-butene copolymer and an ethylene/1-butene/1-hexene terpolymer. The samples of copolymers and their blends were studied by gel permeation chromatography (GPC), differential scanning calorimetry (DSC), 13С NMR spectroscopy, and dynamic mechanical analysis (DMA) using testing machines equipped with a cryochamber. It is proposed that such parameters as "relative elongation at break at -45 °C" and "Izod impact strength at -40 °C" are used instead of the ductile-to-brittle transition temperature to assess frost resistance properties because these parameters are more sensitive to deformation and impact at subzero temperatures for HDPE. LLDPE is shown to exhibit higher relative elongation at break at -45 °C and Izod impact strength at -20 ÷ 60 °C compared to those of LDPE. LLDPE terpolymer added to HDPE (at a content ≥ 25 wt.%) simultaneously increases flow properties and improves tensile properties of the blend at -45 °C. Changes in low-temperature properties as a function of molecular weight, MWD, crystallinity, and branch content were determined for HDPE, LLDPE, and their blends. The DMA data prove the resulting dependences. The reported findings allow one to understand and predict mechanical properties in the HDPE-LLDPE systems at subzero temperatures.