RESUMO
5,6,11,12-tetraphenylnaphthacene (rubrene) exhibits resonant energy properties (ES1,rub≈ 2ET1,rub), resulting in rubrene-based organic light-emitting diode (OLED) devices that undergo the singlet fission (STT) process at room temperature. This unique process gives rise to a distinct magneto-electroluminescence (MEL) profile, differing significantly from the typical intersystem crossing (ISC) process. Therefore, in this paper, we investigate charge generation and separation in the interconnector, and the mechanism of charge transport in tandem OLEDs at room temperature using MEL tools. We fabricate tandem OLEDs comprising green (Alq3) and yellow (Alq3:rubrene) electroluminescence (EL) units using different interconnectors. The results demonstrate that all devices exhibited significant rubrene emission. However, the MEL did not exhibit an STT process with an increasing magnetic field, but rather a triplet-triplet annihilation (TTA) process. This occurrence is attributed to direct carrier trapping within doped EL units, which hinders the transport of rubrene trapped charges, consequently prolonging the lifetime of triplet excitons (T1,rub). Thus, the increased T1,rubconcentration causes TTA to occur at room temperature, causing the rapid decrease of MEL in all devices under high magnetic fields. In devices where only the TTA process occurs, the TTA increases with the increasing current. Consequently, the high magnetic field of devices A-C is only related to TTA. Notably, there exists a high magnetic field TTA of device D in the Alq3/1,4,5,8,9,11-Hexaazatriphenylene-hexacarbonitrile interconnector regardless of the current. This occurs because both EL units in the device emit simultaneously, resulting in the triplet-charge annihilation process of Alq3in the high magnetic field of the MEL. Moreover, the rapid increase in MEL at low magnetic field across all devices is attributed to the ISC between Alq3polaron pairs. This entire process involves Förster and Dexter energy transfer. This article not only provides novel insights into charge generation and separation in the interconnector but also enhances our understanding of the microscopic mechanisms in tandem OLED devices.
RESUMO
Although the effect of the electron blocking layer (EBL) material, deoxyribonucleic acid (DNA), on the electroluminescence (EL) performance of organic light-emitting diodes (OLEDs) has been studied, the process of DNA regulation of exciton recombination region within the device is still unclear. Herein, devices with and without EBL were fabricated using different DNA spin-coating speeds, and the photoelectric performance of device were measured. By using DNA compounded with cetyltrimethyl ammonium (CTMA) as the EBL and hole buffer layer, so-called BioLEDs. The DNA-based green Alq3BioLEDs achieve higher luminance (39 000 cd m-2) and higher current efficiency (8.4 cd A-1), which are increased by 49% and 54%, respectively, compared to the reference OLEDs without the addition of DNA. Similarly, the maximum luminance and efficiency of yellow Rubrene BioLEDs is increased by 64% (from 12 120 to 19 820 cd m-2) and 74% (from 1.36 to 2.36 cd A-1), the luminance and efficiency of blue TCTA BioLEDs is increased by 101% and 245%. Specifically, we found that as the thickness of DNA-CTMA increases, the exciton recombination region moves towards the interface between the emitting layer (EML) and the hole transport layer (HTL). By better confining excitons within the EML, the current efficiency of the BioLEDs is effectively improved. Accordingly, we provide a possible idea for achieve high performance DNA-based BioLEDs by adding DNA-CTMA EBL and hole buffer layers. Meanwhile, as the DNA thickness increases, the exciton recombination region moves towards the EML/HTL interface, thereby enhancing the efficiency of the DNA-based BioLEDs.