Effect of High-radiant Emittance and Short Curing Time on Polymerization Shrinkage Vectors of Bulk Fill Composites.

PURPOSE: To evaluate the effect of short curing time using a high-radiant emittance light on polymerization shrinkage vectors in different consistency bulk-fill composites (BFRCs) using micro-computed tomography. METHODS AND MATERIALS: Radiopaque zirconia fillers were homogeneously incorporated and functioned as radiopaque tracers into two regular-paste: TBFill (Tetric EvoCeram Bulk Fill) and TPFill (Tetric PowerFill), and two flowable (n=6): TBFlow (Tetric EvoFlow Bulk Fill) and TPFlow (Tetric PowerFlow) resin composites. Class I cavities (4 mm depth × 4 mm length × 4 mm width) were 3D-printed and filled in a single increment: TBFill and TBFlow were light-activated using a Bluephase Style 20i (10 seconds in high-mode); TPFill and TPFlow were light-activated using a Bluephase PowerCure (three seconds). The same adhesive system (Adhese Universal) was used for all groups. Microcomputed tomography scans were obtained before and after light-activation. Filler particle movement was identified by polymerization shrinkage vectors at five depths (from 0-4 mm): top, top-middle, middle, middle-bottom and bottom. RESULTS: TPFlow showed the lowest total vector displacement, followed by TBFlow, TBFill and TPFill, significantly different among each other (p<0.05). Generally, BFRCs showed decreased vector displacement with increased depth, and higher displacement at the top-surface (p<0.05). Qualitative analysis showed a similar pattern of vector magnitude and displacement for groups TBFill and TPFill, with displacement vectors on occlusal (top) surfaces toward the center of the restoration from the top to middle areas, and relatively limited displacement at the bottom. TBFlow and TPFlow showed more displacement on the occlusal (top). CONCLUSIONS: Short curing time with high-radiant emittance on fast-curing BFRCs was shown to be a feasible option in terms of vector displacement. Flowable BFRCs presented lower vector displacement than their regular-viscosity versions.

External Marginal Gap Evaluation of Different Resin-filling Techniques for Class II Restorations-A Micro-CT and SEM Analysis.

CLINICAL RELEVANCE: Secondary caries are the main reason for the failure of restorations, class II being the most affected. Techniques that promote less gap percentage are important. Flowable bulk fill composites used at such locations have been shown to decrease gap formation while being a faster procedure than an incremental technique.

Characterization and Comparative Analysis of Voids in Class II Composite Resin Restorations by Optical Coherence Tomography.

PURPOSE: This study aimed to characterize and analyze the number of voids and the percentage of void volume within and between the layers of class II composite restorations made using the bulk fill technique or the incremental technique by optical coherence tomography (OCT). METHODS AND MATERIALS: Class II cavities (4×4×2 mm) were prepared in 48 human third molars (n=24 restorations per group, two class II cavities per tooth). Teeth were divided into four groups and restored as follows: group 1 (FOB), bulk filled in a single increment using Filtek One Bulk Fill (3M Oral Care); group 2 (FXT), incrementally filled using four oblique layers of Filtek Z350 XT (3M Oral Care); group 3 (FBF+FXT), bulk filled in a single increment using Filtek Bulk Fill Flowable Restorative (3M Oral Care) covered with two oblique layers of Filtek Z350 XT (3M Oral Care), and group 4 (FF+FXT), incrementally filled using Filtek Z350 XT Flow (3M Oral Care) covered with two oblique layers of Filtek Z350 XT (3M Oral Care). After the restorative procedure, specimens were immersed into distilled water and stored in a hot-air oven at 37°C. Forty-eight hours later, thermal cycling was conducted (5000 cycles, 5°C to 55°C). Afterward, OCT was used to detect the existence of voids and to calculate the number of voids and percentage of voids volume within each restoration. Data were submitted to chi-square and Kruskal-Wallis tests (α=0.05). Comparisons were made using the Dunn method. RESULTS: Voids were detected in all groups, ranging from 0.000002 (FBF+FXT and FF+FXT) to 0.32 mm3 (FBF+FXT). FF + FXT presented voids in all of the restorations and had a significantly higher number of voids per restoration when compared to the other groups (p<0.05), but restorations with the presence of voids were significantly higher only when compared to FXT (p<0.05). FBF + FXT presented a significantly higher percentage of voids volume than that of FXT (p<0.05). When comparing restorations made using high-viscosity resin-based composites (FOB and FXT), no significant differences regarding number of voids or percentage of voids volume were detected (p≥0.05). CONCLUSIONS: The use of flowable resin-based composites can result in an increased number of voids and percentage of voids volume in restorations, and this appears to be more related to voids present inside the syringe of the material than to the use of incremental or bulk fill restorative techniques.

A new approach for the determination of 210Pb by liquid scintillation counting.

A new approach to the calibration procedure is presented, as there is no need to discount bismuth from lead spectrum when constructing the efficiency curve. This work presents two calibration methods: one considering mostly lead spectrum contributions and other that considers both lead and bismuth contributions. Both methodologies provide consistent results when evaluated in an intercomparison program. Furthermore, this methodology allows simultaneous analysis of several samples and is suitable for any type of sample after proper digestion in liquid form.

Effect of Shortened Light-Curing Modes on Bulk-Fill Resin Composites.

CLINICAL RELEVANCE: Shortened light curing does not affect volumetric polymerization shrinkage or cohesive tensile strength but negatively affects the shear bond strength of some bulk-fill resin composites. When performing shortened light curing, clinicians should be aware of the light output of their light-curing units. SUMMARY: Purpose: To evaluate volumetric polymerization shrinkage (VPS), shear bond strength (SBS) to dentin, and cohesive tensile strength (CTS) of bulk-fill resin composites (BFRCs) light activated by different modes.Methods and Materials: Six groups were evaluated: Tetric EvoCeram bulk fill + high mode (10 seconds; TEC H10), Tetric EvoFlow bulk fill + high mode (TEF H10), experimental bulk fill + high mode (TEE H10), Tetric EvoCeram bulk fill + turbo mode (five seconds; TEC T5), Tetric EvoFlow bulk fill + turbo mode (TEF T5), and experimental bulk fill + turbo mode (TEE T5). Bluephase Style 20i and Adhese Universal Vivapen were used for all groups. All BFRC samples were built up on human molar bur-prepared occlusal cavities. VPS% and location were evaluated through micro-computed tomography. SBS and CTS tests were performed 24 hours after storage or after 5000 thermal cycles; fracture mode was analyzed for SBS.Results: Both TEC H10 and TEE H10 presented lower VPS% than TEF H10. However, no significant differences were observed with the turbo-curing mode. No differences were observed for the same BFRC within curing modes. Occlusal shrinkage was mostly observed. Regarding SBS, thermal cycling (TC) affected all groups. Without TC, all groups showed higher SBS values for high mode than turbo mode, while with TC, only TEC showed decreased SBS from high mode to turbo modes; modes of fracture were predominantly adhesive. For CTS, TC affected all groups except TEE H10. In general, no differences were observed between groups when comparing the curing modes.Conclusions: Increased light output with a shortened curing time did not jeopardize the VPS and SBS properties of the BFRCs, although a decreased SBS was observed in some groups. TEE generally showed similar or improved values for the tested properties in a shortened light-curing time. The VPS was mostly affected by the materials tested, whereas the SBS was affected by the materials, curing modes, and TC. The CTS was not affected by the curing modes.

Microcomputed Tomography Evaluation of Polymerization Shrinkage of Class I Flowable Resin Composite Restorations.

The present study aimed to characterize the pattern and volume of polymerization shrinkage of flowable resin composites, including one conventional, two bulk fill, and one self-adhesive. Standardized class I preparations (2.5 mm depth × 4 mm length × 4 mm wide) were performed in 24 caries-free human third molars that were randomly divided in four groups, according to the resin composite and adhesive system used: group 1 = Permaflo + Peak Universal Bond (PP); group 2 = Filtek Bulk Fill + Scotchbond Universal (FS); group 3 = Surefil SDR + XP Bond (SX); and group 4 = Vertise flow self-adhering (VE) (n=6). Each tooth was scanned three times using a microcomputed tomography (µCT) apparatus. The first scan was done after the cavity preparation, the second after cavity filling with the flowable resin composite before curing, and the third after it was cured. The µCT images were imported into three-dimensional rendering software, and volumetric polymerization shrinkage percentage was calculated for each sample. Data were submitted to one-way analysis of variance and post hoc comparisons. No significant difference was observed among PP, FS, and VE. SX bulk fill resin composite presented the lowest values of volumetric shrinkage. Shrinkage was mostly observed along the occlusal surface and part of the pulpal floor. In conclusion, polymerization shrinkage outcomes in a 2.5-mm deep class I cavity were material dependent, although most materials did not differ. The location of shrinkage was mainly at the occlusal surface.

Effect of Restorative System and Thermal Cycling on the Tooth-Restoration Interface - OCT Evaluation.

The present study evaluated the tooth/noncarious cervical lesion restoration interface when using different adhesive systems and resin composites, submitted to thermal cycling (TC), using optical coherence tomography (OCT). Noncarious cervical lesion (NCCL) preparations (0.7 mm depth × 2 mm diameter) were performed on 60 human third molars and randomly divided into six groups, according to the adhesive system and resin composite used: group 1 = Adper Single Bond 2 (SB2) + Aelite LS Posterior (AP); group 2 = SB2 + Venus Diamond (VD); group = SB2 + Filtek Z250XT (Z250); group 4 = Clearfil SE Bond (CSE) + AP; group 5 = CSE + VD; group 6 = CSE + Z250. Selective enamel etching was performed for 30 seconds on groups 4, 5, and 6, while groups 1, 2, and 3 were etched for 30 seconds in enamel and 15 seconds in dentin. All groups were evaluated using OCT before and after TC (n=10). Images were analyzed using Image J software; enamel and dentin margins were separately evaluated. Data from OCT were submitted to PROC MIXED for repeated measurements and Tukey Kramer test (α = 0.05). No marginal gaps were observed in etched enamel, either before or after TC, for all adhesive and resin composite systems. A significant interaction was found between adhesive system and TC for the dentin groups; after TC, restorations with CSE showed smaller gaps at the dentin/restoration interface compared with SB2 for all resin composites. Increased gap percentages were noticed after TC compared with the gaps before TC for all groups. In conclusion, TC affected marginal integrity only in dentin margins, whereas etched enamel margins remained stable even after TC. Dentin margins restored with CSE adhesive system showed better marginal adaptation than those restored with SB2. Resin composites did not influence marginal integrity of NCCL restorations.

Effect of chemical and mechanical degradation on surface roughness of three glass ionomers and a nanofilled resin composite.

Nanofillers have been incorporated into glass ionomer (GI) restorative materials to improve their mechanical and surface properties. The aim of this present laboratory study was to compare the superficial roughness (Ra) of nanofilled GI (Ketac N100) with that of conventional GI (Fuji IX GP), resin-modified GI (Vitremer), and a nanofilled resin composite (Filtek Supreme) after pH cycling and toothbrush abrasion. Ten specimens of each material were made using Teflon molds, which were polished using aluminum-oxide abrasive disks. Three measurements of Ra were made of each specimen to serve as baseline values. The specimens were submitted to pH cycling for 10 days in a demineralization solution for six hours (pH 4.3) and were then stored in remineralization solution for 18 hours (pH 7.0). Ra measurements were recorded after the pH cycling. Specimens were then submitted to toothbrush abrasion in a brushing machine with a 200g load for 30,000 cycles at 250 cycles/min. The Ra values were then recorded. The surface morphology of specimens from each group was analyzed using a scanning electron microscope. Data were analyzed by analysis of variance, Tukey, and t-tests. After toothbrushing, only Fuji IX GP (1.10 ± 0.80) showed Ra values that were statistically different from those of the other materials evaluated. Ketac N100 (0.68 ± 0.16) showed intermediate Ra values, but it did not differ statistically from the results associated with Vitremer (1.04 ± 0.46) and Filtek (0.30 ± 0.15). Ketac N100 showed intermediate values of superficial roughness among the conventional glass ionomer cement, resin-modified glass ionomer cements, and the nanofilled resin after chemical and mechanical degradation.