Thermal stability and gas absorption characteristics of ionic liquid-based solid polymer electrolytes.

Ionic liquid (IL)-based solid polymer electrolytes (SPE) with stable thermal properties and low electrical resistivity have been evaluated. Two candidates for the polymer component of the SPE, poly(ethylene glycol) diacrylate (PEGDA) and Nafion, were considered. Differential scanning calorimetry analysis and electrical resistivity tests revealed that PEGDA, in comparison to Nafion, enables the formation of uniform SPEs with lower electrical resistivity and better thermal stability within a range of 25 °C-170 °C. Therefore, PEDGA was selected for further evaluation of the IL component effect on the resulting SPE. Six IL candidates, including 1-butyl-3-methylimidazolium methanesulfonate ± methanesulfonic acid (BMIM.MS ± MSA), diethylmethylammonium triflate ±bis(trifluoromethanesulfonyl)imine (Dema.OTF±HTFSI), and 1-butyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide ± bis(trifluoromethanesulfonyl)imine (BMIM.TFSI ± HTFSI), were selected to test the effect of hydrophobicity/hydrophilicity of the IL on the resulting SPE. Fourier transformation infrared spectrometer analysis revealed that the BMIM.MSA-based electrolytes have the highest tendency to absorb from the environment and keep the moisture, while Dema.OTF has the fastest curing time. The SPE candidates were further evaluated for absorption characteristics of different gasses and vapors, such as N2, O2, ethanol vapor, and diluted CO/N2, that were tested with the in situ quartz crystal microbalance (QCM) technique. Among all six candidates, BMIM.MS showed the largest N2 and O2 absorption capacity from the environment. Dema.OTF + HTFSI, meanwhile, demonstrated a higher level of interactions with the ethanol vapor. In the case of CO/N2, QCM analysis revealed that BMIM.MS+MSA has the largest, ∼13 µg/cm2, absorption capacity that is reached within 400 s of being exposed to the gas mixture.

Tribocatalytically-active nickel/cobalt phosphorous films for universal protection in a hydrocarbon-rich environment.

High-contact stresses generated at the sliding interfaces during their relative movement provide a unique combination of local heating and shear- and load-induced compression conditions. These conditions, when involving the sliding of surfaces with certain material characteristics, may facilitate tribochemical reactions with the environment, leading to the formation of a protective, damage-suppressing tribofilm directly at the contact. Here, we employ the electrodeposition process to design a coating composed of a hard cobalt-phosphorous matrix with the inclusion of tribocatalytically-active nickel clusters. The coating is optimized in terms of its relative composition and mechanical characteristics. We demonstrate the excellent tribological performance of the coating in the presence of a hydrocarbon environment, both in the form of a liquid lubricant and as a hydrocarbon-saturated vapor. Characterization of the wear track indicates that the origin of such performance lies in the formation of a protective carbon-based tribofilm on the surface of the coating during sliding. These results contribute to the advancement of knowledge on material transformations in the contact, thus providing a robust and versatile approach to addressing tribological challenges in mechanical systems.

MoVN-Cu Coatings for In Situ Tribocatalytic Formation of Carbon-Rich Tribofilms in Low-Viscosity Fuels.

Inhibiting the tribological failure of mechanical assemblies which rely on fuels for lubrication is an obstacle to maintaining the lifetime of these systems with low-viscosity and low-lubricity fuels. In the present study, a MoVN-Cu nanocomposite coating was tribologically evaluated for durability in high- and low-viscosity fuels as a function of temperature, load, and sliding velocity conditions. The results indicate that the MoVN-Cu coating is effective in decreasing wear and friction relative to an uncoated steel surface. Raman spectroscopy, transmission electron microscopy, and electron-dispersive spectroscopy analysis of the MoVN-Cu worn surfaces confirmed the presence of an amorphous carbon-rich tribofilm which provides easy shearing and low friction during sliding. Further, the characterization of the formed tribofilm revealed the presence of nanoscale copper clusters overlapping with the carbon peak intensities supporting the tribocatalytic origin of the surface protection. The tribological assessment of the MoVN-Cu coating reveals that the coefficient of friction decreased with increasing material wear and initial contact pressure. These findings suggest that MoVN-Cu is a promising protective coating for fuel-lubricated assemblies due to its adaptive ability to replenish lubricious tribofilms from hydrocarbon environments.

Tribocatalytically-activated formation of protective friction and wear reducing carbon coatings from alkane environment.

Minimizing the wear of the surfaces exposed to mechanical shear stresses is a critical challenge for maximizing the lifespan of rotary mechanical parts. In this study, we have discovered the anti-wear capability of a series of metal nitride-copper nanocomposite coatings tested in a liquid hydrocarbon environment. The results indicate substantial reduction of the wear in comparison to the uncoated steel substrate. Analysis of the wear tracks indicates the formation of carbon-based protective films directly at the sliding interface during the tribological tests. Raman spectroscopy mapping of the wear track suggests the amorphous carbon (a-C) nature of the formed tribofilm. Further analysis of the tribocatalytic activity of the best coating candidate, MoN-Cu, as a function of load (0.25-1 N) and temperature (25 °C and 50 °C) was performed in three alkane solutions, decane, dodecane, and hexadecane. Results indicated that elevated temperature and high contact pressure lead to different tribological characteristics of the coating tested in different environments. The elemental energy dispersive x-ray spectroscopy analysis and Raman analysis revealed formation of the amorphous carbon film that facilitates easy shearing at the contact interface thus enabling more stable friction behavior and lower wear of the tribocatalytic coating. These findings provide new insights into the tribocatalysis mechanism that enables the formation of zero-wear coatings.

Macroscale Superlubricity Accomplished by Sb2O3-MSH/C Under High Temperature.

Here, we report the high-temperature superlubricity phenomenon accomplished in coatings produced by burnishing powders of antimony trioxide (Sb2O3) and magnesium silicate hydroxide coated with carbon (MSH/C) onto the nickel superalloy substrate. The tribological analysis performed in an open-air experimental setup revealed that with the increase of testing temperature, the coefficient of friction (COF) of the coating gradually decreases, finally reaching the superlubricity regime (the COF of 0.008) at 300°C. The analysis of worn surfaces using in-situ Raman spectroscopy suggested the synergistic effect of the inner Sb2O3 adhesion layer and the top MSH/C layer, which do not only isolate the substrate from the direct exposure to sliding but also protect it from oxidation. The cross-sectional transmission electron microscopy (TEM) and X-ray photoelectron spectroscopy (XPS) results indicated the tribochemically-activated formation of an amorphous carbon layer on the surface of the coating during sliding. Formation of the film enables the high-temperature macroscale superlubricity behavior of the material system.

Swelling-Assisted Sequential Infiltration Synthesis of Nanoporous ZnO Films with Highly Accessible Pores and Their Sensing Potential for Ethanol.

Here, we report a swelling-assisted sequential infiltration synthesis (SIS) approach for the design of highly porous zinc oxide (ZnO) films by infiltration of block copolymer templates such as polystyrene-block-polyvinyl pyridine with inorganic precursors followed by UV ozone-assisted removal of the polymer template. We show that porous ZnO coatings with the thickness in the range between 140 and 420 nm can be obtained using only five cycles of SIS. The pores in ZnO fabricated via swelling-assisted SIS are highly accessible, and up to 98% of pores are available for solvent penetration. The XPS data indicate that the surface of nanoporous ZnO films is terminated with -OH groups. Density functional theory calculations show a lower energy barrier for ethanol-induced release of the oxygen restricted depletion layer in the case of the presence of -OH groups at the ZnO surface, and hence, it can lead to higher sensitivity in sensing of ethanol. We monitored the response of ZnO porous coatings with different thicknesses and porosities to ethanol vapors using combined mass-based and chemiresistive approaches at room temperature and 90 °C. The porous ZnO conformal coatings reveal a promising sensitivity toward detection of ethanol at low temperatures. Our results suggest the excellent potential of the SIS approach for the design of conformal ZnO coatings with controlled porosity, thickness, and composition that can be adapted for sensing applications.

Combined Tribological and Bactericidal Effect of Nanodiamonds as a Potential Lubricant for Artificial Joints.

The artificial joints, for example, knee and hip implants, are widely used for the treatment of degenerative joint diseases and trauma. The current most common material choice for clinically used implants is the combination of polymer-on-metal structures. Unfortunately, these joints often suffer from high friction and wear, leading to associated inflammation and infection and ultimate failure of the artificial joints. Here, we propose an alternative solution to this tribologically induced failure of the joint materials. We demonstrate that the friction and wear behavior of ultrahigh-molecular-weight polyethylene (UHMWPE) and titanium tribopair, used to mimic the artificial joint interface, can be improved by introducing nanodiamond (ND) particles in the sliding contact. Characterization of the wear track using energy-dispersive spectroscopy and Raman spectroscopy revealed that the tribofilm formed from embedded NDs during sliding significantly suppressed the wear of the UHMWPE surface. In addition to the improved lubrication characteristics, NDs exhibit high biocompatibility with the bone cells and promising antibacterial properties against Staphylococcus aureus, the most common strain associated with artificial joint infection. These results indicate that NDs can be used as a promising nontoxic human-body lubricant with antiwear and antibacterial features, thus demonstrating their great potential to treat artificial joint complications through intra-articular injection.

Nature-Guided Synthesis of Advanced Bio-Lubricants.

Design of environmentally friendly lubricants derived from renewable resources is highly desirable for many practical applications. Here, Orychophragmus violaceus (Ov) seed oil is found to have superior lubrication properties, and this is based on the unusual structural features of the major lipid species-triacylglycerol (TAG) estolides. Ov TAG estolides contain two non-hydroxylated, glycerol-bound fatty acids (FAs) and one dihydroxylated FA with an estolide branch. Estolide branch chains vary in composition and length, leading to their thermal stability and functional properties. Using this concept, nature-guided estolides of castor oil were synthesized. As predicted, they showed improved lubrication properties similar to Ov seed oil. Our results demonstrate a structure-based design of novel lubricants inspired by natural materials.

Discontinuous fatty acid elongation yields hydroxylated seed oil with improved function.

The biosynthesis of 'unusual' fatty acids with structures that deviate from the common C16 and C18 fatty acids has evolved numerous times in the plant kingdom. Characterization of unusual fatty acid biosynthesis has enabled increased understanding of enzyme substrate properties, metabolic plasticity and oil functionality. Here, we report the identification of a novel pathway for hydroxy fatty acid biosynthesis based on the serendipitous discovery of two C24 fatty acids containing hydroxyl groups at the 7 and 18 carbon atoms as major components of the seed oil of Orychophragmus violaceus, a China-native Brassicaceae. Biochemical and genetic evidence are presented for premature or 'discontinuous' elongation of a 3-OH intermediate by a divergent 3-ketoacyl-CoA (coenzyme A) synthase during a chain extension cycle as the origin of the 7-OH group of the dihydroxy fatty acids. Tribology studies revealed superior high-temperature lubricant properties for O. violaceus seed oil compared to castor oil, a high-performance vegetable oil lubricant. These findings provide a direct pathway for designing a new class of environmentally friendly lubricants and unveil the potential of O. violaceus as a new industrial oilseed crop.