RESUMO
Owing to their high deformation ability, 4D printed structures have various applications in origami structures, soft robotics and deployable mechanisms. As a material with programmable molecular chain orientation, liquid crystal elastomer is expected to produce the freestanding, bearable and deformable three-dimensional structure. However, majority of the existing 4D printing methods for liquid crystal elastomers can only fabricate planar structures, which limits their deformation designability and bearing capacity. Here we propose a direct ink writing based 4D printing method for freestanding continuous fiber reinforced composites. Continuous fibers can support freestanding structures during the printing process and improve the mechanical property and deformation ability of 4D printed structures. In this paper, the integration of 4D printed structures with fully impregnated composite interfaces, programmable deformation ability and high bearing capacity are realized by adjusting the off-center distribution of the fibers, and the printed liquid crystal composite can carry a load of up to 2805 times its own weight and achieve a bending deformation curvature of 0.33 mm-1 at 150 °C. This research is expected to open new avenues for creating soft robotics, mechanical metamaterials and artificial muscles.
Assuntos
Cristais Líquidos , Elastômeros , Músculos , Estruturas VegetaisRESUMO
As set in the maximum residue limit regulations of the European Commission, this study aimed to obtain the residual parameters in milk with optimized UPLC-MS/MS conditions and to determine the conclusive drug withdrawal period to ensure food safety. In this research, an ultra-high performance liquid chromatography-tandem mass spectrometry (UPLC-MS/MS) method was developed to study cefquinome sulfate's residue elimination in milk and to calculate cefquinome's withdrawal period. Twelve healthy cows free of endometritis were selected for the experiment. Before using the drug, the vaginal orifice and perineum of each cow was disinfected. One dose of intrauterine perfusion was used for each cow, followed by an additional dose after 72 h. Before administration and 12 h, 18 h, 24 h, 36 h, 42 h, 48 h, 60 h, 66 h, 72 h, 84 h, 90 h, and 96 h after the last dose, milk (10 mL) was gathered from each cow's teat and pooled. For the measurement of cefquinome concentrations in milk, UPLC-MS/MS was performed. A calibration curve was generated using linear regression as follows: Y = 250.86X - 102.29, with a correlation coefficient of 0.9996; the limits of detection and the limits of quantitation were 0.1 µg·kg-1 and 0.2 µg·kg-1, respectively. The average recovery of cefquinome was 88.60 ± 16.33% at 0.2 µg·kg-1, 100.95 ± 2.54% at 10 µg·kg-1, and 97.29 ± 1.77% at 50 µg·kg-1. For 5 consecutive days at the three spiking levels, the intra and inter-day relative standard deviations (RSD) were 1.28%-13.73% and 1.81%-18.44%, respectively; the residual amount of cefquinome was less than the maximum residue limit of 20 µg·kg-1, 36 h after administration; and the residual amount was less than the limit of detection (0.1 µg·kg-1) 48 h after administration. The withdrawal time of cefquinome in cow's milk was 39.8 h, as calculated using WTM1.4 software. In terms of clinical practical use, the withdrawal period of milk was temporarily set at 48 h after the administration of the cefquinome sulfate uterus injection to cows, in accordance with the recommended dose and course.
RESUMO
Improving the resilience of 3D-printed composites through material extrusion technology (MEX) is an ongoing challenge in order to meet the rigorous requirements of critical applications. The primary objective of this research was to enhance the impact resistance of 3D-printed composites by incorporating continuous hybrid fibers. Herein, continuous virgin carbon (1k) and Kevlar (130D and 200D) fibers were used with different weight and volume fractions as reinforcing fibers to produce hybrid and non-hybrid composites for impact resistance testing to obtain energy absorption with different impact energies: 20 J, 30 J, 40 J, and 50 J. Moreover, 0°/90° fiber orientations were used. Hybrid composites with combinations of PLA + CF + 130D KF and PLA + CF + 200D KF showed higher impact resistance, less damaged areas (71.45% to 90.486%), and higher energy absorption (5.52-11.64% more) behaviors compared to PLA + CF non-hybrids. CT scan images provided strong evidence to resist the fracture and breakage patterns, because the stiffness and elongation properties of the fibers acted together in the hybrids specimens. Furthermore, positive hybrid effects of the PLA + CF + KF hybrids also showed an ideal match of toughness and flexibility in order to resist the impacts. In the future, these hybrids will have the potential to replace the single type of composites in the fields of aerospace and automobiles.
RESUMO
Continuous fiber-reinforced composite truss structures have broad application prospects in aerospace engineering owing to their high structural bearing efficiency and multifunctional applications. This paper presents the design and fabrication of multilayer truss structures with controlled mechanical properties based on continuous fiber-reinforced thermoplastic composite 3D printing. Continuous fiber composite pyramid trusses fabricated by 3D printing have high specific stiffness and strength, with maximum equivalent compression modulus and strength of 401.91 MPa and 30.26 MPa, respectively. Moreover, the relative density of a truss structure can be as low as 1.45%. Additionally, structural units can be extended in any direction to form a multilayer truss structure. Structural performance can be controlled by designing the parameters of each layer. This study offers a novel approach for designing a multifunctional multilayer truss structure, a structure with low-density needs and unique load-bearing effects.