Metabolic and Skeletal Characterization of the KK/Ay Mouse Model-A Polygenic Mutation Model of Obese Type 2 Diabetes.

Type 2 diabetes (T2D) increases fracture incidence and fracture-related mortality rates (KK.Cg-Ay/J. The Jackson Laboratory; Available from: https://www.jax.org/strain/002468 ). While numerous mouse models for T2D exist, few effectively stimulate persistent hyperglycemia in both sexes, and even fewer are suitable for bone studies. Commonly used models like db/db and ob/ob have altered leptin pathways, confounding bone-related findings since leptin regulates bone properties (Fajardo et al. in Journal of Bone and Mineral Research 29(5): 1025-1040, 2014). The Yellow Kuo Kondo (KK/Ay) mouse, a polygenic mutation model of T2D, is able to produce a consistent diabetic state in both sexes and addresses the lack of a suitable model of T2D for bone studies. The diabetic state of KK/Ay stems from a mutation in the agouti gene, responsible for coat color in mice. This mutation induces ectopic gene expression across various tissue types, resulting in diabetic mice with yellow fur coats (Moussa and Claycombe in Obesity Research 7(5): 506-514, 1999). Male and female KK/Ay mice exhibited persistent hyperglycemia, defining them as diabetic with blood glucose (BG) levels consistently exceeding 300 mg/dL. Notably, male control mice in this study were also diabetic, presenting a significant limitation. Nevertheless, male and female KK/Ay mice showed significantly elevated BG levels, HbA1c, and serum insulin concentration when compared to the non-diabetic female control mice. Early stages of T2D are characterized by hyperglycemia and hyperinsulinemia resulting from cellular insulin resistance, whereas later stages may feature hypoinsulinemia due to ß-cell apoptosis (Banday et al. Avicenna Journal of Medicine 10(04): 174-188, 2020 and Klein et al. Cell Metabolism 34(1): 11-20, 2022). The observed hyperglycemia, hyperinsulinemia, and the absence of differences in ß-cell mass suggest that KK/Ay mice in this study are modeling the earlier stages of T2D. While compromised bone microarchitecture was observed in this study, older KK/Ay mice, representing more advanced stages of T2D, might exhibit more pronounced skeletal manifestations. Compared to the control group, the femora of KK/Ay mice had higher cortical area and cortical thickness, and improved trabecular properties which would typically be indicative of greater bone strength. However, KK/Ay mice displayed lower cortical tissue mineral density in both sexes and increased cortical porosity in females. Fracture instability toughness of the femora was lower in KK/Ay mice overall compared to controls. These findings indicate that decreased mechanical integrity noted in the femora of KK/Ay mice was likely due to overall bone quality being compromised.

Knowledge extraction and transfer in data-driven fracture mechanics.

Data-driven approaches promise to usher in a new phase of development in fracture mechanics, but very little is currently known about how data-driven knowledge extraction and transfer can be accomplished in this field. As in many other fields, data scarcity presents a major challenge for knowledge extraction, and knowledge transfer among different fracture problems remains largely unexplored. Here, a data-driven framework for knowledge extraction with rigorous metrics for accuracy assessments is proposed and demonstrated through a nontrivial linear elastic fracture mechanics problem encountered in small-scale toughness measurements. It is shown that a tailored active learning method enables accurate knowledge extraction even in a data-limited regime. The viability of knowledge transfer is demonstrated through mining the hidden connection between the selected three-dimensional benchmark problem and a well-established auxiliary two-dimensional problem. The combination of data-driven knowledge extraction and transfer is expected to have transformative impact in this field over the coming decades.

A Comprehensive Study of Al2O3 Mechanical Behavior Using Density Functional Theory and Molecular Dynamics.

This study comprehensively investigates Al2O3's mechanical properties, focusing on fracture toughness, surface energy, Young's modulus, and crack propagation. The density functional theory (DFT) is employed to model the vacancies in Al2O3, providing essential insights into this material's structural stability and defect formation. The DFT simulations reveal a deep understanding of vacancy-related properties and their impact on mechanical behavior. In conjunction with molecular dynamics (MD) simulations, the fracture toughness and crack propagation in Al2O3 are explored, offering valuable information on material strength and durability. The surface energy of Al2O3 is also assessed using DFT, shedding light on its interactions with the surrounding environment. The results of this investigation highlight the significant impact of oxygen vacancies on mechanical characteristics such as ultimate strength and fracture toughness, drawing comparisons with the effects observed in the presence of aluminum vacancies. Additionally, the research underscores the validation of fracture toughness outcomes derived from both DFT and MD simulations, which align well with findings from established experimental studies. Additionally, the research underscores the validation of fracture toughness outcomes derived from DFT and MD simulations, aligning well with findings from established experimental studies. The combination of DFT and MD simulations provides a robust framework for a comprehensive understanding of Al2O3's mechanical properties, with implications for material science and engineering applications.

Effect of glazing and thermocycling on the fracture toughness and hardness of a New fully crystallized aluminosilicate CAD/CAM ceramic material.

BACKGROUND: The mechanical properties of fully crystallized lithium aluminosilicate ceramics may be influenced by intraoral temperature variations and postmilling surface treatment. The purpose of this study is to explore the interplay among glazing, thermocycling, and the mechanical characteristics (namely, fracture toughness and hardness) of fully crystallized lithium aluminosilicate ceramics. METHODS: Bending bars (n = 40) cut from LisiCAD blocks (GC, Japan) were randomly assigned to glazed or unglazed groups (n = 20) and subjected to the single edge v-notch beam method to create notches. A glazing firing cycle was applied to the glazed group, while the unglazed group was not subjected to glazing. Half of the specimens (n = 10) from both groups underwent thermocycling before fracture toughness testing. The fracture toughness (KIC) was evaluated at 23 ± 1 °C using a universal testing machine configured for three-point bending, and the crack length was measured via light microscopy. Seven specimens per group were selected for the hardness test. Hardness was assessed using a Vickers microhardness tester with a 1 kg load for 20 s, and each specimen underwent five indentations following ISO 14705:2016. The Shapiro-Wilk and Kolmogorov-Smirnov tests were used to evaluate the normality of the data and a two-way ANOVA was utilized for statistical analysis. The significance level was set at (α = 0.05). RESULTS: Regardless of the thermocycling conditions, the glazed specimens exhibited significantly greater fracture toughness than did their unglazed counterparts (P < 0.001). Thermocycling had no significant impact on the fracture toughness of either the glazed or unglazed specimens. Furthermore, statistical analysis revealed no significant effects on hardness with thermocycling in either group, and glazing alone did not substantially affect hardness. CONCLUSIONS: The impact of glazing on the fracture toughness of LiSiCAD restorations is noteworthy, but it has no significant influence on their hardness. Furthermore, within the parameters of this study, thermocycling was found to exert negligible effects on both fracture toughness and hardness.

Effect of thermocycling on surface topography and fracture toughness of milled and additively manufactured denture base materials: an in-vitro study.

BACKGROUND: Studies investigating thermocycling effect on surface topography and fracture toughness of resins used in digitally manufactured denture bases are few. The study aimed to assess the impact of thermocycling on surface topography and fracture toughness of materials used for digitally manufactured denture bases. METHODS: Water sorption, solubility, hardness, surface roughness, and fracture toughness of both three-dimensional (3D)-printed and computer-aided design, computer-aided manufacturing (CAD-CAM) milled specimens (n = 50) were assessed both prior to and following 2000 thermocycles, simulating 2 years of clinical aging. Surface hardness (n = 10) was measured using a Vickers hardness testing machine, surface roughness (n = 10) was determined by a contact profilometer, and fracture toughness (n = 20) was measured using the 3-point bend test, then studying the fractured surfaces was done via a scanning electron microscope (SEM). Prior to and following thermocycling, water sorption and solubility (n = 10) were assessed. Normally distributed data was tested using two-way repeated ANOVA and two-way ANOVA, while Mann Whitney U test and the Wilcoxon signed ranks test were used to analyze data that was not normally distributed (α < 0.05). RESULTS: Following thermocycling, Vickers hardness and fracture toughness of both groups declined, with a significant reduction in values of the 3D-printed resin (P < .001). The 3D-printed denture base resins had a rougher surface following thermocycling with a significant difference (P < .001). The sorption and solubility of water of both materials were not affected by thermocycling. CONCLUSIONS: Before and after thermocycling, milled specimens had lower surface roughness and a greater degree of hardness and fracture toughness than 3D-printed specimens. Thermocycling lowered hardness and fracture toughness, and increased surface roughness in both groups, but had no effect on water sorption and solubility.

Effect of artificial aging on fracture toughness and hardness of 3D-printed and milled 3Y-TZP zirconia.

PURPOSE: This study aimed to evaluate the impact of artificial aging on the fracture toughness and hardness of three-dimensional (3D)-printed and computer-aided design and computer-aided manufacturing (CAD-CAM) milled 3 mol% yttria-stabilized tetragonal zirconia polycrystals (3Y-TZP). MATERIALS AND METHODS: Forty bar-shaped specimens (45 × 4 × 3 mm) were prepared using two manufacturing technologies: 3D printing (LithaCon 3Y 210, Lithoz GmbH, Vienna, Austria; n = 20) and milling (Initial Zirconia ST, GC, Japan; n = 20) of 3Y-TZP. The chevron-notch beam method was used to assess the fracture toughness according to ISO 24370. Specimens from each 3Y-TZP group were divided into two subgroups (n = 10) based on the artificial aging process (autoclaving): nonaged and aged. Nonaged specimens were stored at room temperature, while aged specimens underwent autoclave aging at 134°C under 2 bar-pressure for 5 h. Subsequently, the specimens were immersed in absolute 99% ethanol using an ultrasonic cleaner for 5 min. Each specimen was preloaded by subjecting it to a 4-point loading test, with a force of up to 200 N applied for three cycles. Further 4-point loading was conducted at a rate of 0.5 mm/min under controlled temperature and humidity conditions until fracture occurred. The maximum force (Fmax) was recorded and the chevron notch was examined at 30 × magnification under an optical microscope for measurements before the fracture toughness (KIc) was calculated. Microhardness testing was also performed to measure the Vickers hardness number (VHN). A scanning electron microscope (SEM) coupled with an energy dispersive X-ray unit (EDX) was used to examine surface topography and chemical composition. X-ray diffraction (XRD) was conducted to identify crystalline structure. Data were statistically analyzed using two-way ANOVA and Student's t-test with a significance level of 0.05. RESULTS: The nonaged 3D-printed 3Y-TZP group exhibited a significantly higher fracture toughness value (6.07 MPa m1/2) than the milled 3Y-TZP groups (p < 0.001). After autoclave aging, the 3D-printed 3Y-TZP group maintained significantly higher fracture toughness (p < 0.001) compared to the milled 3Y-TZP group. However, no significant differences in hardness values (p = 0.096) were observed between the aged and nonaged groups within each manufacturing process (3D-printed and milled) independently. CONCLUSION: The findings revealed that the new 3D-printed 3Y-TZP produced by the lithography-based ceramic manufacturing (LCM) technology exhibited superior fracture toughness after autoclave aging compared to the milled 3Y-TZP. While no significant differences in hardness were observed between the aged groups, the 3D-printed material demonstrated greater resistance to fracture, indicating enhanced mechanical stability.

Effect of preparation design and endodontic access on fracture resistance of zirconia overlays in mandibular molars: An in vitro study.

PURPOSE: To evaluate the fracture resistance of zirconia overlays, considering various preparation designs and the presence of endodontic access. MATERIALS AND METHODS: Ninety translucent zirconia (5Y-PSZ) overlay restorations were divided into six groups (n = 15/group) based on different preparation designs, with and without endodontic access: chamfer margin 4 mm above the gingival level without (group 1) and with endodontic access (group 2); margin 2 mm above the gingival level without (group 3) and with endodontic access (group 4); overlay with no chamfer margin without (group 5) and with endodontic access (group 6). Restorations were bonded to mandibular first molar resin dies, and the groups with endodontic access were sealed with flowable resin composite. All restorations underwent 100,000 cycles of thermal cycling between 5°C and 55°C, followed by loading until fracture. Maximum load and fracture resistance were recorded. ANOVA with Tukey post-hoc tests were used for statistical comparison (α < 0.05). RESULTS: Fracture resistance significantly varied among overlay designs with and without endodontic access (p < 0.001), except for the no-margin overlays (groups 5 and 6). Overlays with a 2 mm margin above the gingival margin with endodontic access (group 4) exhibited significantly higher fracture resistance compared to both the 4-mm supragingival (group 2) and no-margin (group 6) designs, even when compared to their respective intact groups (groups 1 and 5). There were no significant differences between the no-margin and 4-mm supragingival overlays. CONCLUSION: The more extensive zirconia overlay for mandibular molars is the first choice since the 2 mm margin above the gingival level design withstood considerable loads even after undergoing endodontic access. A no-margin overlay is preferred over the 4-mm supragingival design as it preserves more tooth structure and there was no outcome difference, irrespective of endodontic access. Caution is warranted in interpreting these findings due to the in vitro nature of the study.

Comparative Evaluation of Fracture Toughness and Flexural Strength of Four Different Core Build-up Materials: An In Vitro Study.

AIM: To evaluate and compare the fracture toughness and flexural strength of four different core build-up materials. MATERIALS AND METHODS: A total of 60 samples were divided into four groups (n = 15) group I: dual cure composite resin reinforced with zirconia particles (Luxacore Z), group II: light cure composite resin (Lumiglass DeepCure), group III: zirconia reinforced glass ionomer cement (GIC) (Zirconomer Improved), and group IV: chemically cure composite resin (Self Comp) respectively. All the core build-up materials were manipulated according to the manufacturer's instructions and poured into the mold. A universal testing machine applied a central load to the specimen in a 3-point bending mode. Fracture of the specimen was identified and the reading was recorded by the universal testing machine. The data were analyzed statistically using one-way analysis of variance (ANOVA) and then compared. RESULTS: Group I showed the highest flexural strength (48.65 MPa) among all the groups while group IV showed the lowest flexural strength (17.90 MPa). Group I showed the highest fracture toughness (99.12 MPa) among all the groups while group IV showed the lowest fracture toughness (36.41 MPa.cm-0.5). When mean flexural strength and fracture toughness values of all four groups were compared by using one-way ANOVA, the compared data was highly significant. CONCLUSION: Based on the findings of this study, dual cure composite resin was the material of choice in terms of flexural strength and fracture toughness for core build-up material followed by light cure composite resin. CLINICAL SIGNIFICANCE: The core buildup material serves to strengthen the tooth structure, allowing it to withstand the forces of chewing and preventing the risk of tooth fractures. This material is essential in restoring damaged or decayed teeth, as it provides a stable foundation for further dental work. By reinforcing the tooth structure, the core buildup material ensures that the tooth can function properly and remain healthy for years to come. How to cite this article: Nakade P, Thaore S, Bangar B, et al. Comparative Evaluation of Fracture Toughness and Flexural Strength of Four Different Core Build-up Materials: An In Vitro Study. J Contemp Dent Pract 2024;25(2):191-195.

Fracture Toughness Characteristics of Stacked Bilayer Graphene via Far-Field Displacement Measurements.

Mechanical properties of graphene, e.g., strength, modulus, and fracture toughness are extremely sensitive to flaws. Here the fracture properties of stacked bilayer graphene sheets (SBLG) are reported, obtained via stacking two individually grown graphene sheets. The SBLG is presented here as a building block for flaw-resilient nanomaterials. The fracture properties of freestanding SBLG sheets, suspended on transmission electron microscope (TEM) grids, are characterized by stretching the TEM grid inside an scanning electron microscope (SEM) chamber and monitoring the local displacements in real-time. The fracture toughness is measured and expressed as a function of the critical displacement required to propagate existing cracks in the experiment via computational models. This approach decouples force and displacements measurements, and utilizes the known elastic modulus along with the known displacement boundary conditions at the onset of crack growth to estimate the far field force and stress. This strategy represents a breakthrough in nanoscale fracture mechanics for statistical analysis and high throughput experimens on multiple samples at a time. Results demonstrate that the SBLG is markedly tougher than as-grown single or multilayer graphene, with a mode I fracture toughness of ≈28.06 ± 7.5 MPa m $\sqrt m $ . The mechanisms leading to a higher toughness of SBLG are also analyzed and discussed.

Cellulose nanocrystal functionalized aramid nanofiber reinforced epoxy nanocomposites with high strength and toughness.

The mechanical properties of polymer nanocomposites can be improved by incorporating various types of nanofillers. The hybridization of nanofillers through covalent linkages between nanofillers with different dimensions and morphology can further increase the properties of nanocomposites. In this work, aramid nanofibers (ANFs) are modified using chlorinated cellulose nanocrystals (CNCs) and functionalized with 3-glycidoxypropyltrimethoxysilane to improve the chemical and mechanical interaction in an epoxy matrix. The integration of CNC functionalized ANFs (fACs) in the epoxy matrix simultaneously improves Young's modulus, tensile strength, fracture properties, and viscoelastic properties. The test results show that 1.5 wt% fAC reinforced epoxy nanocomposites improve Young's modulus and tensile strength by 15.1% and 10.1%, respectively, and also exhibit 2.5 times higher fracture toughness compared to the reference epoxy resin. Moreover, the glass transition temperature and storage modulus are found to increase when fACs are incorporated. Thus, this study demonstrates that the enhanced chemical and mechanical interaction by the CNC functionalization on the ANFs can further improve the static and dynamic mechanical properties of polymer nanocomposites.

Characterizing and predicting the relationship between translaminar fracture toughness and pull-out length distributions under distinct temperatures.

The translaminar fracture toughness reflects the damage tolerance of a fibre-reinforced composite under longitudinal tension, which often governs the final failure of structures. One of the main energy-dissipation mechanisms that contributes to the translaminar toughness of composites is the fibre pull-out process. The present study aims to quantify and model the statistical distribution of fibre pull-out lengths formed on the translaminar fracture surface of composites, for the first time in the literature; this is done under different temperatures, so that the relationship between pull-out length distributions, micromechanical properties and the translaminar fracture toughness can be established. The fracture surfaces of cross-ply compact tension specimens tested under three different temperatures have been scanned through X-ray computed tomography to quantify the extent of fibre pull-out on the fracture surfaces; the distribution of pull-out lengths showed alarger average and larger variability with an increase in temperature, which also lead to an increase in translaminar fracture toughness. A similar trend has been captured by the proposed analytical model, which predicts the pull-out length distribution based on the analysis of quasi-fractal idealizations of the fracture surface, yielding an overall accuracy of more than 85%. This article is part of the theme issue 'Ageing and durability of composite materials'.

Fracture Toughness: Bridging the Gap Between Hip Fracture and Fracture Risk Assessment.

PURPOSE OF REVIEW: This review surveys recent literature related to cortical bone fracture mechanics and its application towards understanding bone fragility and hip fractures. RECENT FINDINGS: Current clinical tools for hip fracture risk assessment have been shown to be insensitive in some cases of elevated fracture risk leading to the question of what other factors account for fracture risk. The emergence of cortical bone fracture mechanics has thrown light on other factors at the tissue level that are important to bone fracture resistance and therefore assessment of fracture risk. Recent cortical bone fracture toughness studies have shown contributions from the microstructure and composition towards cortical bone fracture resistance. A key component currently overlooked in the clinical evaluation of fracture risk is the importance of the organic phase and water to irreversible deformation mechanisms that enhance the fracture resistance of cortical bone. Despite recent findings, there is an incomplete understanding of which mechanisms lead to the diminished contribution of the organic phase and water to the fracture toughness in aging and bone-degrading diseases. Notably, studies of the fracture resistance of cortical bone from the hip (specifically the femoral neck) are few, and those that exist are mostly consistent with studies of bone tissue from the femoral diaphysis. Cortical bone fracture mechanics highlights that there are multiple determinants of bone quality and therefore fracture risk and its assessment. There is still much more to learn concerning the tissue-level mechanisms of bone fragility. An improved understanding of these mechanisms will allow for the development of better diagnostic tools and therapeutic measures for bone fragility and fracture.

Fracture toughness and hardness of in-office, 3D-printed ceramic brackets.

OBJECTIVES: Three-dimensional (3D) printing technology is a promising manufacturing technique for fabricating ceramic brackets. The aim of this research was to assess fundamental mechanical properties of in-office, 3D printed ceramic brackets. MATERIALS AND METHODS: 3D-printed zirconia brackets, commercially available polycrystalline alumina ceramic brackets (Clarity, 3 M St. Paul, MN) and 3D-printed customized polycrystalline alumina ceramic ones (LightForce™, Burlington, Massachusetts) were included in this study. Seven 3D printed zirconia brackets and equal number of ceramic ones from each manufacturer underwent metallographic grinding and polishing followed by Vickers indentation testing. Hardness (HV) and fracture toughness (K1c) were estimated by measuring impression average diagonal length and crack length, respectively. After descriptive statistics calculation, group differences were analysed with 1 Way ANOVA and Holm Sidak post hoc multiple comparison test at significance level α = .05. RESULTS: Statistically significant differences were found among the materials tested with respect to hardness and fracture toughness. The 3D-printed zirconia proved to be less hard (1261 ± 39 vs 2000 ± 49 vs 1840 ± 38) but more resistant to crack propagation (K1c = 6.62 ± 0.61 vs 5.30 ± 0.48 vs 4.44 ± 0.30 MPa m1/2 ) than the alumina brackets (Clarity and Light Force respectivelty). Significant differences were observed between the 3D printed and the commercially available polycrystalline alumina ceramic brackets but to a lesser extent. CONCLUSIONS: Under the limitations of this study, the 3D printed zirconia bracket tested is characterized by mechanical properties associated with advantageous orthodontic fixed appliances traits regarding clinically relevant parameters.

Bond strength of ceramic veneered CAD-milled alloy upon prolonged sintering.

OBJECTIVES: Ceramic-sintering affects bond strength and longevity of metal-ceramic. This study investigated the effect of sintering temperatures and times on metal-ceramic bond strength vis-a-vis interfacial fracture toughness. MATERIALS AND METHODS: One hundred eighty rectangular-shaped (25 × 8 × 1 mm) casting (Auriloy® (CA)) and CAD-milling (Ceramill Sintron® (MA)) alloys were prepared and randomly veneered with ceramic at normal (930 °C; (TN)), increased (940 °C; (TI)), and extremely increased (950 °C; (TE)) sintering temperatures and normal (1 min; (HN)), increased (2 min; (HI)), and extremely increased (3 min; (HE)) sintering time (n = 10/group). Pre-cracked was subjected to four loading-unloading cycles at 0.05 mm/min speed to determine interfacial fracture toughness from strain energy release rate (G). Microstructures were examined with a scanning electron microscope (SEM), energy-dispersive X-ray (EDX), and atomic force microscopy (AFM). ANOVA and Tukey comparisons were determined for significant differences (α = 0.05). RESULTS: Significant differences in G due to the effect of alloy, sintering temperature, and time (p < 0.05) were indicated. MA revealed higher G than CA. Raising temperatures enabled increasing G for CA, not for MA. Extended sintering permitted increasing G for both alloys. Rougher surface of MA than CA was observed. Interfacial ion exchange was differently indicated between CA and MA. CONCLUSIONS: Bond strength was influenced by alloy, sintering temperature, and time. Ceramic has better adhesion to MA than CA. Enhancing bond for CA was succeeded through increasing sintering temperature and time, whereas through extended sintering for MA. CLINICAL RELEVANCE: MA offers stronger bond than CA. Enhancing bond is suggested by extended sintering. Raising temperature can enhance bond for CA, not for MA.

Heterogeneous Diamond-cBN Composites with Superb Toughness and Hardness.

The traditional hardness-toughness tradeoff poses a substantial challenge for the development of superhard materials. Due to strong covalent bonds and intrinsic brittleness, the full advantage of microstructure engineering for enhanced mechanical properties requires further exploration in superhard materials. Here heterogeneous diamond-cBN composites were synthesized from a carefully prepared precursor (hBN microflakes uniformly wrapped by onion carbon nanoparticles) through phase transitions under high pressure and high temperature. The synthesized composites inherit the architecture of the precursors: cBN regions with an anisotropic profile that spans several micrometers laterally and several hundred nanometers in thickness are embedded in a nanograined diamond matrix with high-density nanotwins. A significantly high fracture toughness of 16.9 ± 0.8 MPa m1/2 is achieved, far beyond those of single-crystal diamond and cBN, without sacrificing hardness. A detailed TEM analysis revealed multiple toughening mechanisms closely related to the microstructure. This work sheds light on microstructure engineering in superhard materials for excellent mechanical properties.

Mechanical and Electronic Properties of Al(111)/6H-SiC Interfaces: A DFT Study.

A density functional theory (DFT) calculation is carried out in this work to investigate the effect of vacancies on the behavior of Al(111)/6H SiC composites. Generally, DFT simulations with appropriate interface models can be an acceptable alternative to experimental methods. We developed two modes for Al/SiC superlattices: C-terminated and Si-terminated interface configurations. C and Si vacancies reduce interfacial adhesion near the interface, while Al vacancies have little effect. Supercells are stretched vertically along the z-direction to obtain tensile strength. Stress-strain diagrams illustrate that the tensile properties of the composite can be improved by the presence of a vacancy, particularly on the SiC side, compared to a composite without a vacancy. Determining the interfacial fracture toughness plays a pivotal role in evaluating the resistance of materials to failure. The fracture toughness of Al/SiC is calculated using the first principal calculations in this paper. Young's modulus (E) and surface energy (Ɣ) is calculated to obtain the fracture toughness (KIC). Young's modulus is higher for C-terminated configurations than for Si-terminated configurations. Surface energy plays a dominant role in determining the fracture toughness process. Finally, to better understand the electronic properties of this system, the density of states (DOS) is calculated.

Effect of Gum Arabic powder on the mechanical properties of denture base acrylic.

Objective: This study aimed to improve the mechanical properties of denture base material using various concentrations of natural biopolymer, i.e., Gum Arabic (GA). Methods: This experimental study was conducted at the Dental Health Department of the College of Applied Medical Sciences, King Saud University, Riyadh, Saudi Arabia from May 2022 to July 2022. After obtaining exemption from the institutional review board, the powdered GA was added in ratios of weight 5, 10, and 20% to PMMA heat-cured acrylic powder to produce bar-shaped samples (65 × 10 × 30 mm3 in dimensions). While the control group was prepared as such. Micro hardness (n=10/group) and fracture toughness (n=10/group) were evaluated. One-way analysis of variance method was used to statistically analyze the results (p<0.05) using SPSS version 23. Results: Significant differences were observed for micro hardness (p<0.001) and fracture toughness (p=0.007) between the means of the different study groups. The control group exhibited the highest micro hardness (22.5±0.6 VHN) and fracture toughness (1.25±0.11 MPa.m1/2) value among the study groups. While 20 wt. % GA and 10 wt. % GA groups showed the lowest micro hardness and fracture toughness values, respectively. Conclusions: GA powder might not be an appropriate reinforcing material for denture base or the higher filler loading of GA in denture base acrylic might be detrimental to the mechanical properties.

Stretchable Hydrogels with Low Hysteresis and High Fracture Toughness for Flexible Electronics.

Stretchable materials, especially hydrogels, are emerging in various fields recently. Many applications demand low hysteresis and high fracture toughness of the materials to be used under dynamic mechanical loads. Herein, the authors report a hydrogel with high fracture toughness and low hysteresis through using a strong metal coordination bond and relatively high crosslinking density. This design allows the sacrificial bond to remain intact under normal operation, while fracturing to dissipate mechanical energy in the fracture zone to prevent propagation of the cracks. The obtained hydrogel exhibits a low hysteresis (≈1.5%) and a high fracture toughness (≈2,164 J m-2 ). Moreover, the hydrogel possesses a high fatigue threshold of ≈141 J m-2 and a reasonable conductivity. This study provides a worth-adopted approach to synthesize hydrogels with low hysteresis and high fracture toughness.

Influence of Porosity on Fracture Toughness and Fracture Behavior of Antibiotic-Loaded PMMA Bone Cement.

Aseptic loosening is the most common reason for the long-term revision of cemented arthroplasties with fracture of the cement being a postulated cause or contributing factor. In our previous studies we showed that adding an antibiotic to a polymethylmethacrylate (PMMA) bone cement led to detrimental effects on various mechanical properties of the cement such as bending strength, compressive strength and fracture toughness (KIC). This finding implied that the mechanical failure of antibiotic-loaded PMMA bone cement was influenced by its pore volume fraction. Up to now this aspect has not been studied. Hence the purposes of this study were to determine (1) the influence of antibiotic (telavancin) loading on the KIC of a widely used PMMA bone cement brand (Palacos®R) and (2) the influence of pore size and pore distribution on the fracture behavior of the KIC specimens. For (2) both experimental and numerical methods (extended finite element method [XFEM]) were used allowing a comparison between the two sets of results. We found that: (1) KIC decreased with increased porosity with the drop (relative to the value for the control cement) being significant when the telavancin loading was 4.8 wt/wt % (2 g of telavancin added to 40 g of control cement powder); (2) there was a critical pore size above which there was a significant decrease in KIC and is 1 mm; (3) crack propagation was strongly influenced by pore size and pore locations (pore-pore interactions); and, (4) there was good agreement between the experimental and XFEM results. The implications of these findings for the use of a telavancin-loaded PMMA bone cement in cemented total joint arthroplasties are commented upon.

Humidity dependence of fracture toughness of cellulose fibrous networks.

Cellulose-based materials are increasingly finding applications in technology due to their sustainability and biodegradability. The sensitivity of cellulose fiber networks to environmental conditions such as temperature and humidity is well known. Yet, there is an incomplete understanding of the dependence of the fracture toughness of cellulose networks on environmental conditions. In the current study, we assess the effect of moisture content on the out-of-plane (i.e., z-dir.) fracture toughness of a particular cellulose network, specifically Whatman cellulose filter paper. Experimental measurements are performed at 16% RH along the desorption isotherm and 23, 37, 50, 75% RH along the adsorption isotherm using out-of-plane tensile tests and double cantilever beam (DCB) tests. Cohesive zone modeling and finite element simulations are used to extract quantitative properties that describe the crack growth behavior. Overall, the fracture toughness of filter paper decreased with increasing humidity. Additionally, a novel model is developed to capture the high peak and sudden drop in the experimental force measurement caused by the existence of an initiation region. This model is found to be in good agreement with experimental data. The relative effect of each independent cohesive parameter is explored to better understand the cohesive zone-based humidity dependence model. The methods described here may be applied to study rupture of other fiber networks with weak bonds.