Hard X-ray imaging and tomography at the Biomedical Imaging and Therapy beamlines of Canadian Light Source.

The Biomedical Imaging and Therapy facility of the Canadian Light Source comprises two beamlines, which together cover a wide X-ray energy range from 13 keV up to 140 keV. The beamlines were designed with a focus on synchrotron applications in preclinical imaging and veterinary science as well as microbeam radiation therapy. While these remain a major part of the activities of both beamlines, a number of recent upgrades have enhanced the versatility and performance of the beamlines, particularly for high-resolution microtomography experiments. As a result, the user community has been quickly expanding to include researchers in advanced materials, batteries, fuel cells, agriculture, and environmental studies. This article summarizes the beam properties, describes the endstations together with the detector pool, and presents several application cases of the various X-ray imaging techniques available to users.

Heitt Mjölnir: a heated miniature triaxial apparatus for 4D synchrotron microtomography.

Third- and fourth-generation synchrotron light sources with high fluxes and beam energies enable the use of innovative X-ray translucent experimental apparatus. These experimental devices access geologically relevant conditions whilst enabling in situ characterization using the spatial and temporal resolutions accessible at imaging beamlines. Here, Heitt Mjölnir is introduced, a heated miniature triaxial rig based on the design of Mjölnir, but covering a wider temperature range and larger sample volume at similar pressure capacities. This device is designed to investigate coupled thermal, chemical, hydraulic and mechanical processes from grain to centimetre scales using cylindrical samples of 10 mm × 20 mm (diameter × length). Heitt Mjölnir can simultaneously reach confining (hydraulic) pressures of 30 MPa and 500 MPa of axial stress with independently controlled sample pore fluid pressure < 30 MPa. This internally heated apparatus operates to temperatures up to 573 K with a minimal vertical thermal gradient in the sample of <0.3 K mm-1. This new apparatus has been deployed in operando studies at the TOMCAT (Swiss Light Source), I12 JEEP (Diamond Light Source) and PSICHÉ (Synchrotron SOLEIL) beamlines for 4D X-ray microtomography with scan intervals of a few minutes. Heitt Mjölnir is portable and modular, allowing a wide range of 4D characterizations of low-grade metamorphism and deformational processes. It enables spatially and temporally resolved fluid-rock interaction studies at conditions of crustal reservoirs and is suitable for characterization of material properties in geothermal, carbonation or subsurface gas storage applications. Technical drawings and an operation guide are included in this publication.

ForMAX - a beamline for multiscale and multimodal structural characterization of hierarchical materials.

The ForMAX beamline at the MAX IV Laboratory provides multiscale and multimodal structural characterization of hierarchical materials in the nanometre to millimetre range by combining small- and wide-angle X-ray scattering with full-field microtomography. The modular design of the beamline is optimized for easy switching between different experimental modalities. The beamline has a special focus on the development of novel fibrous materials from forest resources, but it is also well suited for studies within, for example, food science and biomedical research.

Exploratory neutron tomography of articular cartilage.

OBJECTIVE: To investigate the feasibility of using neutron tomography to gain new knowledge of human articular cartilage degeneration in osteoarthritis (OA). Different sample preparation techniques were evaluated to identify maximum intra-tissue contrast. DESIGN: Human articular cartilage samples from 14 deceased donors (18-75 years, 9 males, 5 females) and 4 patients undergoing total knee replacement due to known OA (all female, 61-75 years) were prepared using different techniques: control in saline, treated with heavy water saline, fixed and treated in heavy water saline, and fixed and dehydrated with ethanol. Neutron tomographic imaging (isotropic voxel sizes from 7.5 to 13.5 µm) was performed at two large scale facilities. The 3D images were evaluated for gradients in hydrogen attenuation as well as compared to images from absorption X-ray tomography, magnetic resonance imaging, and histology. RESULTS: Cartilage was distinguishable from background and other tissues in neutron tomographs. Intra-tissue contrast was highest in heavy water-treated samples, which showed a clear gradient from the cartilage surface to the bone interface. Increased neutron flux or exposure time improved image quality but did not affect the ability to detect gradients. Samples from older donors showed high variation in gradient profile, especially from donors with known OA. CONCLUSIONS: Neutron tomography is a viable technique for specialized studies of cartilage, particularly for quantifying properties relating to the hydrogen density of the tissue matrix or water movement in the tissue.

3D Quantification of Pore Networks and Anthropogenic Carbon Mineralization in Stacked Basalt Reservoirs.

Basalt formations are promising candidates for the geologic storage of anthropogenic CO2 due to their storage capacity, porosity, permeability, and reactive geochemical trapping ability. The Wallula Basalt Carbon Storage Pilot Project demonstrated that supercritical CO2 injected into >800 m deep Columbia River Basalt Group stacked reservoir flow tops mineralizes to ankerite-siderite-aragonite on month-year time scales, with 60% of the 977 metric tons of CO2 converted within 2 years. The potential impacts of mineral precipitation and consequent changes in the rock porosity, pore structure, pore size, and pore size distributions have likely been underestimated hitherto. Herein, we address these knowledge gaps using X-ray microcomputed tomography (XMT) to evaluate the pore network architecture of sidewall cores recovered 2 years after CO2 injection. In this study, we performed a detailed quantitative analysis of the CO2-reacted basalt cores by XMT imaging. Reconstructed 3D images were analyzed to determine the distribution and volumetric details of porosity and anthropogenic carbonate nodules in the cores. Additional mineralogic quantification provided insight into the overall paragenesis and carbonate growth mechanisms, including mineralogic/chemical zonation. These findings are being used to parametrize multiphase reactive transport models to predict the fate and transport of subsurface CO2, enabling scale-up to commercial-scale geologic carbon storage in basalts and other reactive mafic-ultramafic formations.

Trade-off between Pore-Throat Structure and Mineral Composition in Modulating the Stability of Soil Organic Carbon.

The preservation of soil organic carbon (OC) is an effective way to decelerate the emission of CO2 emission. However, the coregulation of pore structure and mineral composition in OC stabilization remains elusive. We employed the in situ nondestructive oxidation of OC by low-temperature ashing (LTA) combined with near edge X-ray absorption fine structure (NEXAFS), high-resolution microtomography (µ-CT), field emission electron probe microanalysis (FE-EPMA) with C-free embedding, and novel Cosine similarity measurement to investigate the C retention in different aggregate fractions of contrasting soils. Pore structure and minerals contributed equally (ca. 50%) to OC accumulation in macroaggregates, while chemical protection played a leading role in C retention with 53.4%-59.2% of residual C associated with minerals in microaggregates. Phyllosilicates were discovered to be more prominent than Fe (hydr)oxides in C stabilization. The proportion of phyllosilicates-associated C (52.0%-61.9%) was higher than that bound with Fe (hydr)oxides (45.6%-55.3%) in all aggregate fractions tested. This study disentangled quantitatively for the first time a trade-off between physical and chemical protection of OC varying with aggregate size and the different contributions of minerals to OC preservation. Incorporating pore structure and mineral composition into C modeling would optimize the C models and improve the soil C content prediction.

The potential of x-ray virtual histology in the diagnosis of skin tumors.

BACKGROUND: Histopathological analysis represents the gold standard in clinical practice for diagnosing skin neoplasms. While the current diagnostic workflow has specialized in producing robust and accurate results, interpreting tissue architecture and malignant cellular morphology correctly remains one of the greatest challenges for pathologists. This paper aims to explore the prospect of applying x-ray virtual histology to human skin tumor excisions and correlating it with the histological validation. MATERIALS AND METHODS: Seven skin biopsies containing intriguing melanoma types and pigmented skin lesions were scanned using x-ray Computed micro-Tomography (µCT) and then sectioned for conventional histology assessment. RESULTS: The tissue microarchitecture reconstructed by µCT offers detailed insights into diagnosing the malignancy or benignity of the skin lesions. Three-dimensional reconstruction via x-ray virtual histology reveals infiltrative patterns in basal cell carcinoma and evaluated invasiveness in melanoma. The technology enables the identification of pagetoid distributions of neoplastic cells and the assessment of melanoma depth in three dimensions. CONCLUSION: Although the proposed approach is not intended to replace conventional histology, the non-destructive nature of the sample and the clarity provided by virtual inspection demonstrate the promising impact of µCT as a valid support method prior to conventional histological sectioning. Indeed, µCT images can suggest the optimal sectioning position before using a microtome, as is commonly performed in histological practice. Moreover, the three-dimensional nature of the proposed approach paves the way for a more accurate assessment of significant prognostic factors in melanoma, such as Breslow thickness, by considering the whole micro-volume rather than a two-dimensional observation.

Simultaneous analysis of shape and internal structure of a curved Hibiscus cannabinus pulvinus: X-ray microtomography and semi-automated quantification.

In the Malvaceae family, dynamic solar tracking by leaves is actuated by the deformation of the pulvinus, a thickened region at the leaf blade-petiole junction. While the internal structure is believed to play a crucial role in this process, experimental verification has been challenging due to technical limitations. To address this gap, we developed a semi-automated workflow, which integrates data analysis and image processing to simultaneously analyze the shape and internal structure of a Malvaceae pulvinus using X-ray microtomography. Firstly, we found that kenaf (Hibiscus cannabinus L.), a Malvaceae species with curved pulvini, exhibited solar-tracking leaf movement and selected it as a model system. We employed diffusible iodine-based contrast-enhanced computed tomography to visualize the internal structure of the kenaf pulvinus. Analysis of the pulvini's shape revealed variations in pulvinus morphology, yet plausible prediction of the centerline was accomplished using polar polynomial regression. Upon slicing the pulvini perpendicular to the centerline, we observed distinct gray value gradients along the proximo-distal and adaxial-abaxial axes, challenging threshold-based tissue segmentation. This workflow successfully generated three modified 3D images and derived quantitative parameters. Using these quantitative parameters, we conducted network analysis and found the linkage between the size-normalized cortex cross-sectional area and curvature. Polynomial least absolute shrinkage and selection operator (LASSO) regression revealed the relationship between the size-normalized cortex cross-sectional area and curvature commonly in all three tested samples. This workflow enables simultaneous analysis of the shape and internal structure, significantly improving the reproducibility of Malvaceae leaf pulvinus characterization.

The effect of root canal preparation tapers on planktonic bacteria and biofilm reduction in the apical third: A correlative microtomography and microbiological laboratory study.

AIM: To evaluate the influence of different preparation tapers on the reduction in planktonic bacteria and biofilms of Enterococcus faecalis and Candida albicans in the apical third (4 mm) of the mesial roots of mandibular molars, correlating decontamination with canal shape. METHODOLOGY: After microtomography analysis for morphological standardization of the canals, 48 mandibular molar roots, each containing two canals (96 canals), were contaminated with E. faecalis and C. albicans and divided into four groups (n = 11) for canal instrumentation using ProDesign Logic 2 files with different tapers G (.03): # 25.03; G (.04): # 25.04; G (.05): # 25.05; and G (.06): # 25.06 and irrigation with 2.5% sodium hypochlorite. Four roots were examined under a scanning electron microscope (SEM) to qualitatively assess biofilm formation. Eight roots were used as the negative control group (samples were not contaminated). Bacteriological samples were taken exclusively from the apical third of the roots before and after chemical-mechanical preparation and bacterial counts were determined (CFU/mL). The final micro-CT scan was used to quantify the volume variation and unprepared canal area in the apical third. Statistical analysis was performed using the Kruskal-Wallis, Student-Newman-Keuls and Wilcoxon tests for analysis of microbiological data. anova and the Tukey or Games-Howell test were used for analysis of micro-CT data and Spearman's test for correlations (α = 5%). RESULTS: All groups showed a significant reduction in bacteria (p < .05), with no statistically significant difference between groups. There was no significant difference in per cent volume increase between groups. The unprepared area (Δ%) was affected by the file used (p = .026) and was significantly lower for G (.06) compared to G (.03). There was no statistically significant correlation among bacterial reduction, volume and unprepared area (p > .05). CONCLUSION: The different preparation tapers influenced root canal shaping in the apical third but did not improve decontamination in this region.

In vitro early proximal caries detection using trilateral short-wave infrared reflection at 1050 and 1550 nm.

OBJECTIVES: This in vitro study evaluated the diagnostic potential of short-wave infrared reflection (SWIRR) at 1050 and 1550 nm for proximal caries detection from the occlusal, buccal and lingual surfaces of posterior teeth under clinically relevant conditions. Bitewing radiography (BWR) was the alternative index test and micro-computed tomography (µCT) the reference standard. METHODS: 250 proximal surfaces of extracted human teeth were examined using SWIRR at 1050 and 1550 nm and BWR. SWIRR, BWR and µCT findings were evaluated twice by two trained examiners. SWIRR images were evaluated from occlusal and trilateral (occlusal, buccal and lingual combined) views. Sensitivity, specificity and AUC were calculated. Reliability assessment was performed using κ statistics. RESULTS: SWIRR (1050 nm) showed sensitivity of 0.44 for occlusal and 0.55 for trilateral assessment, paired with specificity of 0.96 and 0.90, whereas SWIRR (1550 nm) showed sensitivity of 0.73 and 0.85 paired with specificity of 0.76 and 0.59. Compared to occlusal view, trilateral SWIRR view revealed ≈10% higher sensitivity and lower specificity. BWR revealed lowest sensitivity (0.30) and highest specificity (0.99). Over-and underestimation of caries demonstrated opposite trends: from 1050-1550 nm, overestimation of trilateral SWIRR increased (0.08-0.29), while underestimation decreased (0.15-0.06). CONCLUSION: Trilateral SWIRR has higher sensitivity and lower specificity for proximal caries, than occlusal SWIRR. 1050 nm are more suitable for trilateral SWIRR and 1550 nm for occlusal examinations. A combination of SWIRR at 1050 and 1550 nm may exhibit a balanced sensitivity and specificity for proximal caries.

Investigation of the furcation morphology of permanent mandibular first molars by using micro-computed tomography.

BACKGROUND: To investigate the anatomic features of the root furcation of permanent mandibular first molars. METHODS: A total of 50 extracted mandibular first molars (25 two-rooted and 25 three-rooted) were collected and scanned using micro-computed tomography. The digital models of teeth and root canal systems were reconstructed three-dimensionally. The tooth models were displayed in parallel projection mode from buccal and distal views. Screenshots were captured and subsequently analyzed using Image-Pro Plus 6.0 software after calibration. The furcation angle, root trunk length, maximum depth and level of distal root concaves of mesial roots, and length of enamel projections were measured, and the furcation types (classified into type V, type U and type W) were detected. Statistical analysis was performed using the Shapiro-Wilk's test, one-way analysis of variance, Student's t-test and Chi-square test. RESULTS: The mean furcation angle between the distobuccal (DB) and distolingual (DL) roots (in distal view) was the greatest (59.2°), whereas the furcation angle between the mesial and DL roots (in buccal view) was the smallest (25.4°) among the four furcation angles (all p < 0.05). Regarding the furcation types, bucco-lingual root trunk length, maximum depth and site of the distal root concavities, and enamel projection length, no significant differences were detected between the three- and two-rooted molar groups (all p > 0.05). The frequency of type V was the highest (54.0%), followed by type U (26.0%), and type W had the lowest occurrence rate (20.0%). The mean length of distal root trunk in the three-rooted mandibular molars was significantly greater than that of the buccal/lingual one (3.7 mm vs. 3.0 mm, p < 0.01). The maximum depth of the distal concavities of the mesial roots was on average 0.66 ± 0.19 mm, and the site was located at an average of 2.8 ± 1.3 mm below furcation. The mean length of buccal enamel projections was significantly longer than that of lingual ones (3.1 mm vs. 0.7 mm, p < 0.01). CONCLUSIONS: The furcation anatomy of the mandibular first molar is complex, and the presence of the DL root may further complicate its topography. A thorough understanding of these anatomic features is essential for successful periodontal treatment.

High-energy synchrotron-radiation-based X-ray micro-tomography enables non-destructive and micro-scale palaeohistological assessment of macro-scale fossil dinosaur bones.

Palaeohistological analysis has numerous applications in understanding the palaeobiology of extinct dinosaurs. Recent developments of synchrotron-radiation-based X-ray micro-tomography (SXMT) have allowed the non-destructive assessment of palaeohistological features in fossil skeletons. Yet, the application of the technique has been limited to specimens on the millimetre to micrometre scale because its high-resolution capacity has been obtained at the expense of a small field of view and low X-ray energy. Here, SXMT analyses of dinosaur bones with widths measuring ∼3 cm under a voxel size of ∼4 µm at beamline BL28B2 at SPring-8 (Hyogo, Japan) are reported, and the advantages of virtual-palaeohistological analyses with large field of view and high X-ray energy are explored. The analyses provide virtual thin-sections visualizing palaeohistological features comparable with those obtained by traditional palaeohistology. Namely, vascular canals, secondary osteons and lines of arrested growth are visible in the tomography images, while osteocyte lacunae are unobservable due to their micrometre-scale diameter. Virtual palaeohistology at BL28B2 is advantageous in being non-destructive, allowing multiple sampling within and across skeletal elements to exhaustively test the skeletal maturity of an animal. Continued SXMT experiments at SPring-8 should facilitate the development of SXMT experimental procedures and aid in understanding the paleobiology of extinct dinosaurs.

Investigating the interfaces of the epiphyseal plate: An integrated approach of histochemistry, microtomography and SEM.

We investigated the interfaces of the epiphyseal plate with over- and underlying bone segments using an integrated approach of histochemistry, microtomography and scanning electron microscopy (SEM) to overcome the inherent limitations of sections-based techniques. Microtomography was able to provide an unobstructed, frontal view of large expanses of the two bone surfaces facing the growth plate, while SEM observation after removal of the soft matrix granted an equally unhindered access with a higher resolution. The two interfaces appeared widely dissimilar. On the diaphyseal side the hypertrophic chondrocytes were arranged in tall columns packed in a sort of compact palisade; the interposed extracellular matrix was actively calcifying into a thick mineralized crust growing towards the epiphysis. Behind the mineralization front, histochemical data revealed a number of surviving cartilage islets which were being slowly remodelled into bone. In contrast, the epiphyseal side of the cartilage consisted of a relatively quiescent reserve zone whose mineralization was marginal in amount and discontinuous in extension; the epiphyseal bone consisted of a loose trabecular meshwork, with ample vascular spaces opening directly into the non-mineralized cartilage. On both sides the calcification process took place through the formation of spheroidal bodies 1-2 µm wide which gradually grew by apposition and coalesced into a solid mass, in a way distinctly different from that of bone and other calcified tissues.

Anatomical study of the red flour beetle using synchrotron radiation X-ray phase-contrast micro-tomography.

Synchrotron X-ray phase-contrast microtomography (SR-PhC micro-CT) is well established, fast and non-destructive imaging technique for data acquisition that is currently being used to obtain new insights into insect anatomy and function in physiological, morphological and phylogenetic studies. In this study, we described in situ the internal organs of the red flour beetle Tribolium castaneum Herbst 1797, a widespread pest of cereals and stored food causing serious damage to the human economy. Two-dimensional virtual sections and volumetric reconstructions of the nervous, alimentary and reproductive systems were carried out in both sexes. The results provided a comprehensive overview of the morphological characteristics of this species, such as the different maturation stages of ovarioles and the realistic location, size and shape of internal organs. Given the great interest in this model species in experimental biology and forensic entomology, complete knowledge of the general anatomy is required for future functional applications in pest control and experimental studies. In addition, this study confirms SR-PhC micro-CT as a powerful and innovative tool in entomology, particularly suitable for small species and chitinized structures that are difficult to analyse using conventional dissection and histological methods.

Oscillation of the orientation of cardiomyocyte aggregates in human left ventricle free wall.

Orientation of local cardiomyocyte aggregates in the human left ventricle free wall experiences an oscillation in the laminar structure regions, besides its gradual change trend. We described this oscillation using five transmural samples imaged at the European Synchrotron Radiation Facility with an isotropic voxel size of 3.5 × 3.5 × 3.5 µm3 . In the reconstructed volume of each sample, we manually selected a region containing a regular laminar structure as the region of interest and measured the distribution of the orientation of local cardiomyocyte aggregates inside using a Fourier-based method. Then, we extracted the gradual change part of the orientation of cardiomyocyte aggregates with a three-dimensional centered Gaussian filter and measured the angle between the original orientation vector of local cardiomyocyte aggregates and its gradual change part. Further, we assessed the measured angles in different local coordinates. The results indicate that the oscillation amplitude of the orientation of cardiomyocyte aggregates is regional in the left ventricle wall, which may promote our understanding of the rearrangement mechanism of the cardiomyocyte aggregates and provide a new biomarker to study the heart physiological status.

Investigation of Rhodnius prolixus head anatomy using microtomography.

In the last years, microtomography has proved to be a powerful technique on insects' studies, allowing a detailed view of the structures' internal with a high resolution. One of the most important advantages about the use of microtomography in these studies is the fact that the dissection is not necessary, which decreases considerably the number of samples used on the insects' research. Some insects are used constantly in studies about morphology, metamorphosis, and reproduction, because they work as a model for others, and Rhodnius prolixus is one of the most studied in this group. This insect is also one of the main insect vectors of Chagas disease that kills around 12,000 people every year in Latin America. Some studies using laboratory microtomography conventional scanners combining with the correct staining methods have proved that it could be a powerful tool in biological research, allowing the visualisation of low-density tissues. The main goal of the present work was to use staining protocols to study Rhodnius prolixus with laboratory microtomography conventional scanners. The experiments were carried out at the imaging lab in the Theoretical Biology Department, University of Vienna, using an Xradia MicroXCT and at the University of Oslo, using a Skyscan 2211.

Analysing the effect of sodium bicarbonate and glycine air polishing on tooth surfaces with two different imaging methods.

The aim of this study was to compare two different imaging methods by assessing changes caused by sodium bicarbonate and glycine air polishing on the tooth surfaces. Fourteen single root teeth with exposed root surfaces were included into the study. The teeth were randomly divided into two groups: sodium bicarbonate and glycine group. Samples were scanned in a micro-computed tomography (micro-CT) and CAD/CAM (computer-aided design/computer-aided manufacturing) at baseline and then after air-polishing powder applications, the defect volume values were evaluated. There was a statistically significant difference between mean defect volume values that occurred after glycine and sodium bicarbonate air polishing evaluated with micro-CT and CAD/CAM (p < 0.05). After sodium bicarbonate air polishing, defect volume on enamel surface at maximum power and defect volume on the exposed root surface at medium power values calculated with CAD/CAM were higher. After glycine air polishing, defect volume values on both surfaces at medium power setting calculated with CAD/CAM were lower. Defect volume values on enamel surface at maximum power setting calculated with CAD/CAM were higher than calculated with micro-CT. We concluded that CAD/CAM cannot provide as accurate results as micro-CT. Glycine-based powder is less abrasive than sodium bicarbonate, especially on enamel surface. Lay Description: Micro-CT is a non-destructive imaging method with high resolution and allows to examine all tooth structures individually. CAD/CAM are systems that are widely used in dentistry today. Access to the device is easier than micro-CT. Intraoral scanners in CAD/CAM systems also provide non-destructive image scanning. The aim of this study was to compare two different imaging methods by assessing changes caused by sodium bicarbonate and glycine air polishing on the tooth surfaces. The results showed that because of the analyses made with CAD/CAM, similar results could not be obtained with micro-CT and cannot be used to evaluate the changes that occur after air polishing.

Feasibility study of direct CT lymphangiography in mice: comparison with interstitial CT/MR lymphangiography.

OBJECTIVES: To establish a CT lymphangiography method in mice via direct lymph node puncture. METHODS: We injected healthy mice (n = 8) with 50 µl of water-soluble iodine contrast agent (iomeprol; iodine concentration, 350 mg/mL) subcutaneously into the left-rear foot pad (interstitial injection) and 20 µl of the same contrast agent directly into the popliteal lymph node (direct puncture) 2 days later. Additionally, we performed interstitial MR lymphangiography on eight mice as a control group. We calculated the contrast ratio for each lymph node and visually assessed the depiction of lymph nodes and lymphatic vessels on a three-point scale. RESULTS: The contrast ratios of 2-min post-injection images of sacral and lumbar-aortic lymph nodes were 20.7 ± 16.6 (average ± standard deviation) and 17.1 ± 12.0 in the direct puncture group, which were significantly higher than those detected in the CT or MR interstitial lymphangiography groups (average, 1.8-3.6; p = 0.008-0.019). The visual assessment scores for sacral lymph nodes, lumbar-aortic lymph nodes, and cisterna chyli were significantly better in the direct puncture group than in the CT interstitial injection group (p = 0.036, 0.009 and 0.001, respectively). The lymphatic vessels between these structures were significantly better scored in direct puncture group than in the CT or MR interstitial lymphangiography groups at 2 min after injection (all p ≤ 0.05). CONCLUSIONS: In CT lymphangiography in mice, the direct lymph node puncture provides a better delineation of the lymphatic pathways than the CT/MR interstitial injection method. KEY POINTS: • The contrast ratios of 2-min post-injection images in the direct CT lymphangiography group were significantly higher than those of CT/MR interstitial lymphangiography groups. • The visibility of lymphatic vessels in subjective analysis in the direct CT lymphangiography group was significantly better in the direct puncture group than in the CT/MR interstitial lymphangiography groups. • CT lymphangiography with direct lymph node puncture can provide excellent lymphatic delineation with contrast being maximum at 2 min after injection.

Gilsonicaris from the Lower Devonian Hunsrück slate is a eunicidan annelid and not the oldest crown anostracan crustacean.

The Lower Devonian (Lower Emsian, -400 Myr) roof slates of the Hunsrück in southeastern Germany have delivered a highly diverse and exceptionally preserved marine fauna that provides a unique snapshot into the anatomy and ecology of a wide range of Palaeozoic animals. Several of the described taxa, however, remain enigmatic in their affinity, at least until new pyritized features hidden under the surface of the slate are revealed using X-ray radiography or micro-computed tomography (µCT). Here, we redescribe such an enigmatic fossil, the putative anostracan crustacean Gilsonicaris rhenanus Van Straelen, 1943. Using µCT scanning, we unveil unprecedented details of its anatomy, including a ventral oral opening and four pairs of recalcitrant jaw elements. These jaws are morphologically consistent with the scolecodonts of eunicidan polychaetes, which along with the gross anatomy of the body and head unambiguously identifies G. rhenanus as a polychaete rather than an arthropod. While this discovery firmly discards the Early Devonian record of crown anostracans in the fossil record, it adds a new record of eunicidan soft tissues, which are surprisingly rare considering the abundant microfossil record of scolecodonts.

Lactobacillus fermentum attenuates the alveolar bone loss in ligature-induced periodontitis in mice.

OBJECTIVE: This study investigated the effects of Lactobacillus fermentum BELF11 on periodontitis in mice (LIP). METHODS: Sixty mice were randomly assigned to a control group (CTL), LIP/PBS group (LIP and PBS applied), or LIP/BELF11 group (LIP and L. fermentum BELF11 applied). For 14 days, PBS or L. fermentum BELF11 was applied twice daily to the mice in the LIP/PBS or LIP/BELF11 group, respectively. After 14 days, radiographic, histological, and pro-inflammatory cytokine assessments were conducted. RESULTS: The LIP/PBS and LIP/BELF11 groups demonstrated greater alveolar bone loss than the CTL group (p < 0.05). The LIP/BELF11 group showed significantly reduced alveolar bone loss on the mesial side compared to the LIP/PBS group. Histologically, the LIP/BELF11 group showed consistent patterns of connective tissue fiber arrangement, lower levels of inflammatory infiltration, less alveolar bone loss, and higher alveolar bone density than the LIP/PBS group, despite showing more signs of destruction than the CTL group. The LIP/BELF11 group also exhibited significantly lower levels of pro-inflammatory cytokines than the LIP/PBS group. CONCLUSIONS: L. fermentum BELF11 inhibits alveolar bone loss and periodontitis progression by regulating pro-inflammatory cytokine production. These findings suggest that L. fermentum BELF11 may be a potential adjunctive therapy in periodontal treatment.