Vertical Dipole Dominates Charge Carrier Lifetime in Monolayer Janus MoSSe.

Two-dimensional semiconductor materials with vertical dipoles are promising photocatalysts as vertical dipoles not only promote the electron-hole separation but also enhance the carrier redox ability. However, the influence of vertical dipoles on carrier recombination in such materials, especially the competing relationship between vertical dipoles and band gaps, is not yet clear. Herein, first-principles calculations and nonadiabatic molecular dynamics simulations were combined to clarify the influence of band gap and vertical dipole on the carrier lifetime in Janus MoSSe monolayer. By comparing with the results of MoS2 and MoSe2 as well as exploring the carrier lifetime of MoSSe under strain regulation, it has been demonstrated that the vertical dipole, rather than the band gap, is the dominant factor affecting the carrier lifetime. Strikingly, a linear relationship between the carrier lifetime and vertical dipole is revealed. These findings have important implications for the design of high-performance photocatalysts and optoelectronic devices.

Vacancy-Rich MoSSe with Sulfiphilicity-Lithiophilicity Dual Function for Kinetics-Enhanced and Dendrite-Free Li-S Batteries.

The sluggish redox kinetics of sulfur and the uncontrollable growth of lithium dendrites are two main challenges that impede the practical applications of lithium-sulfur (Li-S) batteries. In this study, a multifunctional host with vacancy-rich MoSSe vertically grown on reduced graphene oxide aerogels (MoSSe/rGO) is designed as the host material for both sulfur and lithium. The embedding of Se into a MoS2 lattice is introduced to improve the inherent conductivity and generate abundant anion vacancies to endow the 3D conductive graphene based aerogels with specific sulfiphilicity-lithiophilicity. As a result, the assembled Li-S batteries based on MoSSe/rGO exhibit greatly improved capacity and cycling stability and can be operated under a lean electrolyte (4.8 µL mg-1) and a high sulfur loading (6.5 mg cm-2), achieving a high energy density. This study presents a unique method to unlock the catalysis capability and improve the inherent lithiophilicity by heteroatom doping and defect chemistry for kinetics-enhanced and dendrite-free Li-S batteries.

Microenvironment Created by SnSe2 Vapor and Pre-Selenization to Stabilize the Surface and Back Contact in Kesterite Solar Cells.

The ambient air-processed preparation of kesterite Cu2 ZnSn(S,Se)4 (CZTSSe) thin film is highly promising for the fabrication of low-cost and eco-friendly solar cells. However, the Sn volatilization loss and formation of a thick Mo(S,Se)2 interfacial layer during the traditional selenization process pose challenges for fabricating high-efficiency CZTSSe solar cells. Here, CZTS precursors prepared by a sol-gel process in ambient air are selenized and assisted with SnSe2 vapor via one- and two-step selenization to prepare a CZTSSe absorber on a Mo film and, subsequently, solar cells. For one-step selenization, the thickness of the fine grain and Mo(S,Se)2 layers near the back contact can be significantly reduced with increasing SnSe2 vapor partial pressure in the mixed selenization atmosphere, while the device efficiency is only 7.97% due to the severe interface recombination. For two-step selenization, the desired morphology and stoichiometry of the absorber can be achieved through the assistance of Sn-poor precursors selenized with high SnSe2 vapor partial pressure to regulate the Sn content in CZTSSe, yielding the highest efficiency of 10.85%. This study improves the understanding of the key role of the microenvironment during film growth towards the production of high-efficiency thin film solar cells and other photoelectronic devices.

Improving Catalytic Activity of "Janus" MoSSe Based on Surface Interface Regulation.

The monolayer Janus MoSSe is considered to be a promising catalytic material due to its unique asymmetric structure. In order to improve its catalytic performance for hydrogen evolution reactions (HERs) and oxygen evolution reactions (OERs), many attempts have been made. In this work, a series of transition metal (TM) atoms were anchored on the Janus MoSSe surface to screen effective TM single-atom catalysts for HERs and OERs through density functional theory (DFT) calculations. Fe@MoSSe presents excellent HERs performance and Ni@MoSSe presents excellent catalytic performance for OERs with extremely low over-potential of 0.32 V. The enhanced activity is attributed to the modest energy level of the d band center of the transition metal atom, and the transition metal atom improves the conductivity of the original MoSSe and offers unoccupied states near the Fermi level. At the same time, the anchoring of transition metal atoms redistributes the charge in the MoSSe system, which effectively regulates the electronic structure of the material itself. The strain calculation shows that the activity of the catalyst can be improved by reasonably adjusting the value of the applied strain.

Stacked Janus Device Concepts: Abrupt pn-Junctions and Cross-Plane Channels.

Janus transition metal dichalcogenides with a built-in structural cross-plane (cp) asymmetry have recently emerged as a new class of two-dimensional materials with a large cp dipole. Using first-principles calculations, and a tailored transport method, we demonstrate that stacking graphene and MoSSe Janus structures result in record high homogeneous doping of graphene and abrupt, atomically thin, cross-plane pn-junctions. We show how graphene in contrast to metals can act as electrodes to Janus stacks without screening the cp dipole and predict a large photocurrent response dominated by a cp transport channel in a few-layer stacked device. The photocurrent is above that of a corresponding thin-film silicon device illustrating the great potential of Janus stacks, for example, in photovoltaic devices.

Detecting Hachimoji DNA: An Eight-Building-Block Genetic System with MoS2 and Janus MoSSe Monolayers.

In the pursuit of personalized medicine, the development of efficient, cost-effective, and reliable DNA sequencing technology is crucial. Nanotechnology, particularly the exploration of two-dimensional materials, has opened different avenues for DNA nucleobase detection, owing to their impressive surface-to-volume ratio. This study employs density functional theory with van der Waals corrections to methodically scrutinize the adsorption behavior and electronic band structure properties of a DNA system composed of eight hachimoji nucleotide letters adsorbed on both MoS2 and MoSSe monolayers. Through a comprehensive conformational search, we pinpoint the most favorable adsorption sites, quantifying their adsorption energies and charge transfer properties. The analysis of electronic band structure unveils the emergence of flat bands in close proximity to the Fermi level post-adsorption, a departure from the pristine MoS2 and MoSSe monolayers. Furthermore, leveraging the nonequilibrium Green's function approach, we compute the current-voltage characteristics, providing valuable insights into the electronic transport properties of the system. All hachimoji bases exhibit physisorption with a horizontal orientation on both monolayers. Notably, base G demonstrates high sensitivity on both substrates. The obtained current-voltage (I-V) characteristics, both without and with base adsorption on MoS2 and the Se side of MoSSe, affirm excellent sensing performance. This research significantly advances our understanding of potential DNA sensing platforms and their electronic characteristics, thereby propelling the endeavor for personalized medicine through enhanced DNA sequencing technologies.

Nanoscrolls of Janus Monolayer Transition Metal Dichalcogenides.

Tubular structures of transition metal dichalcogenides (TMDCs) have attracted attention in recent years due to their emergent physical properties, such as the giant bulk photovoltaic effect and chirality-dependent superconductivity. To understand and control these properties, it is highly desirable to develop a sophisticated method to fabricate TMDC tubular structures with smaller diameters and a more uniform crystalline orientation. For this purpose, the rolling up of TMDC monolayers into nanoscrolls is an attractive approach to fabricating such a tubular structure. However, the symmetric atomic arrangement of a monolayer TMDC generally makes its tubular structure energetically unstable due to considerable lattice strain in curved monolayers. Here, we report the fabrication of narrow nanoscrolls by using Janus TMDC monolayers, which have an out-of-plane asymmetric structure. Janus WSSe and MoSSe monolayers were prepared by the plasma-assisted surface atom substitution of WSe2 and MoSe2 monolayers, respectively, and then were rolled by solution treatment. The multilayer tubular structures of Janus nanoscrolls were revealed by scanning transmission electron microscopy observations. Atomic resolution elemental analysis confirmed that the Janus monolayers were rolled up with the Se-side surface on the outside. We found that the present nanoscrolls have the smallest diameter of about 5 nm, which is almost the same as the value predicted by the DFT calculation. The difference in work functions between the S- and Se-side surfaces was measured by Kelvin probe force microscopy, which is in good agreement with the theoretical prediction. Strong interlayer interactions and anisotropic optical responses of the Janus nanoscrolls were also revealed by Raman and photoluminescence spectroscopy.

Direct formation of interlayer excitons in MoSSe/WSSe van der Waals heterobilayer.

In respect to the van der Waals structures composed of two-dimensional transition metal dichalcogenides, the interlayer excitonic physics plays a determinative role in the exciting new phenomena and applications in such as photonics, optoelectronics and valleytronics. In this work, beyond the well-accepted, conventional indirect two-step process, we proved that the large interlayer polarization can cause the direct formation of interlayer excitons in MoSSe/WSSe. In MoSSe/WSSe, the interlayer exciton with a sizable oscillator strength is located at 1.49 eV, well below the characteristic intralayer excitons, with a significantly reduced exciton binding energy of 0.28 eV and an improved exciton lifetime of 2.25 ns.

Monolayer Graphene-MoSSe van der Waals Heterostructure for Highly Responsive Gate-Tunable Near-Infrared-Sensitive Broadband Fast Photodetector.

Transition metal dichalcogenides (TMDCs) are potential two-dimentional materials as natural partners of graphene for highly responsive van der Waals (vdW) heterostructure photodetectors. However, the spectral detection range of the detectors is limited by the optical bandgap of the TMDC, which acts as a light-absorbing medium. Bandgap engineering by making alloy TMDC has evolved as a suitable approach for the development of wide-band photodetectors. Here, broadband (visible to near-infrared) photodetection with high sensitivity in the near-infrared region is demonstrated in a MoSSe/graphene heterostructure. In the ambient environment, the photodetector exhibits high responsivity of 0.6 × 102 A/W and detectivity of 7.9 × 1011 Jones at 800 nm excitation with a power density of 17 fW/µm2 and 10 mV source-drain bias. The photodetector shows appreciable responsivity in self-bias mode due to nonuniform distribution of MoSSe flakes on the graphene layer between the source and drain end and the asymmetry between the two electrodes. Time-dependent photocurrent measurements show fast rise/decay times of ∼38 ms/∼48 ms. A significant gate tunability on the efficiency of the detector has been demonstrated. The device is capable of low power detection and exhibits high operational frequency, gain, and bandwidth. Thus, the MoSSe/graphene heterostructure can be a promising candidate as a high-speed and highly sensitive near-infrared photodetector capable of operating at ambient conditions with low energy consumption.

Role of introduced Se element and induced anion vacancies in Mo(SSe)2-x/G van der Waals heterostructure for enhanced hydrogen evolution reaction.

The Gibbs free energy of hydrogen adsorption at the edge of molybdenum disulfide (MoS2) is close to that of Pt, meaning that MoS2 is the best candidate to replace Pt-based materials. However, easy agglomeration between layers to mask active sites, lack of catalytic activity in the basal planes, and poor electronic conductivity make MoS2 exhibit dissatisfactory hydrogen evolution reaction (HER) catalytic performance. Here, we successfully construct a van der Waals heterostructure stacked alternately with Mo(SSe)2-x and graphene (Mo(SSe)2-x/G) to enhance its catalytic ability. The introduction of Se into MoS2 and the thermal treatment induce the sample to generate more anion vacancies. Theoretical and experimental results demonstrate the constructed van der Waals heterostructure, the introduced Se element, and the increased anion vacancies are in favor of promoting the number of active sites and improving the electronic conductivity of the catalyst. Therefore, Mo(SSe)2-x/G exhibits superior HER catalytic performance (the overpotentials of 137 mV and 136 mV at a current of 10 mA cm-2) and long-term stabilities (>90 h and 140 h at a current density of 20 mA cm-2) in both acidic and alkaline media.

Single noble metals (Pd, Pt and Ir) anchored Janus MoSSe monolayers: Efficient oxygen reduction/evolution reaction bifunctional electrocatalysts and harmful gas detectors.

The binding properties of single noble metal atoms (Pd, Pt and Ir) anchored Janus MoSSe monolayers (MLs), the catalytic activity of Pd- and Pt-MoSSe in oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) as well as the adsorption behaviors of Ir-MoSSe for harmful NO, CO and NH3 molecules are systematically studied from the first-principles calculations. Current results reflect the ascending order (Pd-MoSSe < Pt-MoSSe < Ir-MoSSe) of stability and binding strength as well as the tunable electronic properties of Janus MoSSe ML by anchoring single Pd, Pt and Ir atoms. Pd- and Pt-MoSSe exhibit excellent bifunctional catalytic performance, especially the former having lower overpotentials 0.43 and 0.50 V for ORR and OER, which are better than the well-known Pt (111) (0.45 V) and IrO2 (0.56 V) electrocatalysts, respectively. The adsorption nature for NO, CO and NH3 molecules changes from physisorption (on pristine MoSSe) to chemisorption (on Ir-MoSSe), especially for NO and CO molecules due to their ultra-low adsorption energies (-3.72 and -2.91 eV, respectively). Thus, Pd- and Pt-MoSSe (particularly the former) may act as promising highly-efficient ORR/OER bifunctional electrocatalysts, and Ir-MoSSe may serve as a potential sensitive harmful gas detector for NO and CO molecules.

Raman Spectroscopy of Janus MoSSe Monolayer Polymorph Modifications Using Density Functional Theory.

Two-dimensional transition metal dichalcogenides (TMDs) with Janus structures are attracting increasing attention due to their emerging superior properties in breaking vertical mirror symmetry when compared to conventional TMDs, which can be beneficial in fields such as piezoelectricity and photocatalysis. The structural investigations of such materials, along with other 2D materials, can be successfully carried out using the Raman spectroscopy method. One of the key elements in such research is the theoretical spectrum, which may assist in the interpretation of experimental data. In this work, the simulated Raman spectrum of 1H-MoSSe and the predicted Raman spectra for 1T, 1T', and 1H' polymorph modifications of MoSSe monolayers were characterized in detail with DFT calculations. The interpretation of spectral profiles was made based on the analysis of the lattice dynamics and partial phonon density of states. The presented theoretical data open the possibility of an accurate study of MoSSe polymorphs, including the control of the synthesized material quality and the characterization of samples containing a mixture of polymorphs.

In-Plane Strain Tuned Electronic and Optical Properties in Germanene-MoSSe Heterostructures.

DFT calculations are performed to investigate the electronic and optical absorption properties of two-dimensional heterostructures constructed by Janus MoSSe and germanene. It is found that a tiny gap can be opened up at the Dirac point in both Ge/SMoSe and Ge/SeMoS heterostructures, with intrinsic high-speed carrier mobility of the germanene layer being well preserved. An n-type Schottky contact is formed in Ge/SMoSe, while a p-type one is formed in Ge/SeMoS. Compared to corresponding individual layers, germanene-MoSSe heterostructures can exhibit extended optical absorption ability, ranging from ultraviolet to infrared light regions. The position of the Dirac cone, the Dirac gap value as well as the position of the optical absorption peak for both Ge/SMoSe and Ge/SeMoS heterostructures can be tuned by in-plane biaxial strains. It is also predicted that a Schottky-Ohmic transition can occur when suitable in-plane strain is imposed (especially tensile strain) on heterostructures. These results can provide a helpful guide for designing future nanoscale optoelectronic devices based on germanene-MoSSe vdW heterostructures.

Molybdenum sulfide selenide ultrathin nanosheets anchored on carbon tubes for rapid-charging sodium/potassium-ion batteries.

The structural stability and reaction kinetics of anodes are essential factors for high-performance battery systems. Herein, the molybdenum sulfide selenide (MoSSe) nanosheets anchored on carbon tubes (MoSSe@CTs) are synthesized by a facile hydrothermal method combining with further selenization/calcination treatment. The unique tubular carbon skeletons expose abundant active sites for the well-dispersed growth of MoS2 ultrathin nanosheets on both sides of the tubular carbon skeleton. In addition, the further selenization treatment can expand the interlayer spacing of molybdenum sulfide (MoS2) nanosheets and facilitate the fast sodium/potassium-ion transition and storage. When used in sodium-ion batteries (SIBs), MoSSe@CTs electrode delivers a specific capacity of 486 mAh g-1 at 1 A g-1 and retains a stable reversible capacity of 465 mAh g-1 after 1000 cycles, indicating its good cycling stability. For potassium-ion batteries (KIBs), the MoSSe@CTs composite shows a capacity of 352 mA hg-1 at 1 A g-1 and a good cycling stability (maintains at 272 mA hg-1 after 1000 cycles). This work shows informative guiding significance for exploring advanced electrode materials of sodium/potassium-ion batteries.

Synthesis and Characterization of Metallic Janus MoSH Monolayer.

Janus transition-metal dichalcogenides (TMDCs) are emerging as special 2D materials with different chalcogen atoms covalently bonded on each side of the unit cell, resulting in interesting properties. To date, several synthetic strategies have been developed to realize Janus TMDCs, which first involves stripping the top-layer S of MoS2 with H atoms. However, there has been little discussion on the intermediate Janus MoSH. It is critical to find the appropriate plasma treatment time to avoid sample damage. A thorough understanding of the formation and properties of MoSH is highly desirable. In this work, a controlled H2-plasma treatment has been developed to gradually synthesize a Janus MoSH monolayer, which was confirmed by the TOF-SIMS analysis as well as the subsequent fabrication of MoSSe. The electronic properties of MoSH, including the high intrinsic carrier concentration (∼2 × 1013 cm-2) and the Fermi level (∼ - 4.11 eV), have been systematically investigated by the combination of FET device study, KPFM, and DFT calculations. The results demonstrate a method for the creation of Janus MoSH and present the essential electronic parameters which have great significance for device applications. Furthermore, owing to the metallicity, 2D Janus MoSH might be a potential platform to observe the SPR behavior in the mid-infrared region.

Trifunctional Electrocatalysts with High Efficiency for the Oxygen Reduction Reaction, Oxygen Evolution Reaction, and Na-O2 Battery in Heteroatom-Doped Janus Monolayer MoSSe.

Trifunctional electrocatalysts with high activity for the oxygen reduction reaction (ORR), oxygen evolution reaction (OER), and Na-O2 battery are eagerly desirable for electrochemical energy applications. Currently, it remains challenging to achieve such trifunctionality on a single catalyst, although many systems can exhibit either one or two activities. Herein, on the basis of first-principles calculations, Ni-doped Janus monolayer MoSSe with superior electrocatalytic activity toward ORR for fuel cells and OER for water splitting is proposed. Both its ORR and OER display an ultralow overpotential, and the ORR possesses a high selectivity with the Faradaic efficiency approximating 100%. Importantly, it further shows high performance of Na-O2 batteries with a low overpotential of 0.49/0.59 V for ORR/OER, suggesting it being the excellent trifunctional catalyst. Such catalytic behaviors are largely due to the synergistic effect of the built-in electric field and heteroatom doping. These findings not only gain deeper insight into the catalytic activity of Janus monolayer MoSSe but also guide developing effective trifunctional electrocatalysts.

Preparation of High-Percentage 1T-Phase Transition Metal Dichalcogenide Nanodots for Electrochemical Hydrogen Evolution.

Nanostructured transition metal dichalcogenides (TMDs) are proven to be efficient and robust earth-abundant electrocatalysts to potentially replace precious platinum-based catalysts for the hydrogen evolution reaction (HER). However, the catalytic efficiency of reported TMD catalysts is still limited by their low-density active sites, low conductivity, and/or uncleaned surface. Herein, a general and facile method is reported for high-yield, large-scale production of water-dispersed, ultrasmall-sized, high-percentage 1T-phase, single-layer TMD nanodots with high-density active edge sites and clean surface, including MoS2 , WS2 , MoSe2 , Mo0.5 W0.5 S2 , and MoSSe, which exhibit much enhanced electrochemical HER performances as compared to their corresponding nanosheets. Impressively, the obtained MoSSe nanodots achieve a low overpotential of -140 mV at current density of 10 mA cm-2 , a Tafel slope of 40 mV dec-1 , and excellent long-term durability. The experimental and theoretical results suggest that the excellent catalytic activity of MoSSe nanodots is attributed to the high-density active edge sites, high-percentage metallic 1T phase, alloying effect and basal-plane Se-vacancy. This work provides a universal and effective way toward the synthesis of TMD nanostructures with abundant active sites for electrocatalysis, which can also be used for other applications such as batteries, sensors, and bioimaging.