A finite element analysis of stress distribution with various directions of intermaxillary fixation using orthodontic mini-implants and elastics following mandibular advancement with a bilateral sagittal split ramus osteotomy.

OBJECTIVE: This finite element analysis (FEA) aimed to assess the stress distribution in the mandible and fixation system with various directions of the intermaxillary fixation (IMF) using mini-implants (MIs) and elastics following mandibular advancement with a bilateral sagittal split ramus osteotomy (BSSRO). MATERIALS AND METHODS: A total of nine mandibular advancement models were set according to the position of the MIs (1.6 mm in diameter, 8 mm in length) and direction of the IMF elastics (1/4 inch, 5 oz). Major and minor principal stresses in the cortical and cancellous bones, von Mises stresses in the fixation system (miniplate and monocortical screws), and bending angles of the miniplate were analysed. RESULTS: Compressive and tensile stress distributions in the mandible and von Mises stress distributions in the fixation system were greater in models with a Class III IMF elastic direction and a higher IMF elastic force than in models with a Class II IMF elastic direction and a lower IMF elastic force. The bending angle of the miniplate was negligible. CONCLUSIONS: Stress distributions in the bone and fixation system varied depending on the direction, amount of force, and position of IMF elastics and MIs. Conclusively, IMF elastics in the Class II direction with minimal load in the area close to the osteotomy site should be recommended.

Investigation of the efficacy of two different laser types in the treatment of lower lip paresthesia after sagittal split ramus osteotomy.

Orthognathic surgery involves invasive and major surgical procedures commonly used to correct maxillofacial deformities. Bilateral sagittal split ramus osteotomy (BSSO) is often used to treat dentofacial anomalies related to the mandible, but it can result in various complications, the most common of which is inferior alveolar nerve damage. Nerve damage-induced paresthesia of the lower lip significantly affects patient comfort. Medical treatments such as steroids and vitamin B, low-level laser therapy (LLLT), and platelet-rich fibrin (PRF) can be used as supportive therapies for nerve regeneration after damage. This study aimed to investigate the effectiveness of two different types of lasers in treating lower lip paresthesia after BSSO. This clinical trial was a controlled, single-center, prospective, single-blind, randomized study. Thirty patients were included in the study and randomly assigned to three groups: Group I (laser GRR, n = 10) received transcutaneous and transmucosal GRR laser treatment, Group II (Epic10 laser, n = 10) received transmucosal and transcutaneous Epic10 laser treatment, and Group III (vitamin B, n = 10) received B-complex vitamin tablets orally once a day. Two-point and brush tests were performed six times at specific intervals, and a visual analog scale was used to evaluate pain and sensitivity. Both vitamin B and laser therapies accelerated nerve regeneration. The contribution of the laser groups to the healing rate was better than that of the vitamin B group. Although there was no statistically significant difference between the two laser groups, clinical observations indicated better results in the GRR laser group.

Change in taste sensation after orthognathic surgery.

OBJECTIVE: The objective of this study was to evaluate the effect of orthognathic surgery on taste sensation. MATERIALS AND METHODS: Thirty-five patients scheduled to undergo Le Fort I osteotomy (LFIO), sagittal split ramus osteotomy (SSRO), and bimaxillary surgery (BMS) were evaluated by administering localized and whole-mouth taste tests preoperatively and postoperatively at months 1, 3, and 6. The patients were asked to identify the quality of four basic tastes applied to six locations on the palate and tongue and to rate the taste intensities they perceived. Taste recognition thresholds and taste intesity scores were evaluted according to operation groups and follow-ups. RESULTS: There were significant decreases in the quinine HCl recognition thresholds at the postoperative follow-ups compared to the preoperative in LFIO patients (p = 0.043). There were significant decreases in sucrose taste intensity scores in the right posterolateral part of the tongue at months 3 and 6 compared to preoperative in SSRO patients (p = 0.046), and significant increases in quinine HCL taste intensity scores in the right and left anterior parts of the tongue at month 6 compared to preoperative in LFIO patients (p < 0.05). CONCLUSION: Taste perception is affected due to potential damage to the chemosensory nerves during orthognathic surgical procedures. Generally, non-significant alterations have been observed in taste perception after orthognathic surgery, except for significant alterations in bitter and sweet taste perceptions. CLINICAL RELEVANCE: Maxillofacial surgeons should be aware of taste perception change after orthognathic surgery procedures and patients should be informed accordingly. THE TRIAL REGISTRATION NUMBER (TRN): NCT06103422/Date of registration: 10.17.2023 (retrospectively registered).

Simultaneous standard total joint prosthesis reconstruction with SSRO and Le Fort I osteotomy in the treatment of unilateral temporomandibular joint ankylosis with jaw deformity: a case cohort study.

OBJECTIVE: Unilateral temporomandibular joint ankylosis with jaw deformity (UTMJAJD) may require simultaneous total joint prosthesis (TJP) reconstruction, sagittal split ramus (SSRO), and Le Fort I osteotomies. The purpose of this study was to evaluate outcomes in patients treated with these procedures. METHODS: Patients diagnosed UTMJAJD between 2016 and 2018 were selected for the study. Mandible-first procedure was performed after ankylosis release with TJP on the ankylosed side and SSRO on the contralateral side. Le Fort I osteotomy with and without genioplasty was lastly performed. Maximal incisor opening (MIO), facial symmetry, and jaw and condyle stability were compared before, after operation, and during follow-ups. RESULTS: Seven patients were included in the study. Their average chin deviation was 9.5 ± 4.2 mm, and maxillary cant was 5.1 ± 3.0°. After operation, jaw deformity significantly improved, with chin deviation corrected 7.6 ± 4.1 mm (p = 0.015) and advanced 5.9 ± 2.5 mm (p = 0.006). After an average follow-up of 26.6 ± 17.1 months, MIO significantly increased from 11.4 ± 9.3 to 35.7 ± 2.6 mm (p = 0.000). The occlusion was stable with no significant positional or rotational changes of the jaw (p > 0.05). There was no obvious condylar resorption during follow-ups. CONCLUSION: Simultaneous TJP reconstruction, SSRO, and Le Fort I osteotomy are reliable and effective methods for the treatment of UTMJAJD.

Comparison of the skeletal stability after mandibular counter-clockwise rotation in three surgical procedures.

The treatment of mandibular deformities with an anterior open bite is challenging. In this study, skeletal stability after mandibular osteotomies was evaluated to determine the best treatment for mandibular prognathism with an anterior open bite in three procedures: intraoral vertical ramus osteotomy (IVRO), conventional sagittal split ramus osteotomy (conv-SSRO), and SSRO without bone fixation (nonfix-SSRO). Patients who underwent mandibular osteotomy to correct skeletal mandibular protrusion were included. Changes in skeletal and soft tissues were assessed using lateral cephalograms taken before (T1), 3 ± 2 days (T2), and 12 ± 3 months (T3) after surgery. Thirty-nine patients were included: nine in the IVRO group and 11 and 19 in the conv- and nonfix-SSRO groups, respectively. The mandibular plane angles (MPAs) of the T2-T1 were - 2.7 ± 2.0 (p = 0.0040), - 3.7 ± 1.7 (p < 0.0001), and - 2.3 ± 0.7 (p < 0.0001) in the IVRO, conv-SSRO, and nonfix-SSRO groups, respectively. The skeletal relapse of the MPAs was not related to the MPA at T2-T1, and it was approximately 1.3° in the conv-SSRO group. The skeletal relapse of the MAPs was significantly correlated with the MPA of T2-T1 in the IVRO (p = 0.0402) and non-fix-SSRO (p = 0.0173) groups. When the relapse of the MPAs was less than 1.3°, the MPA of T2-T1 was calculated as 2.5° in the nonfix-SSRO group. When the MPA of T2-T1 is less than 2.5°, non-fix SSRO may produce a reliable outcome, and when it is more than 2.5°, conv-SSRO may produce better outcomes.

Morphological Changes of the Mandibular Angle After Orthognathic Surgery with Class III Deformity in East Asia.

The aims of this study were to analyze the morphological changes of the mandibular angle after orthognathic surgery for mandibular setback and investigate related factors. This retrospective study included patients from January 2017 to December 2021 diagnosed with skeletal class III deformity who underwent BSSRO (Group I) or bimaxillary surgery (Group II). Preoperative (T0), within 1 month postoperatively (T1), and 6 months postoperatively (T2) CT scans were collected from 61 patients to three-dimensionally analyze the proximal segment displacement, the linear and angular changes of the mandibular angle. The gonion points moved posteriorly and laterally (P < 0.001), while the inferior movement was not significant (P = 1.000, P = 0.274). The intergonial width increased by 3.32 ± 1.87 mm and 2.34 ± 1.77 mm as revealed by T2 CTs, respectively, in Group I and Group II. Mandibular angle decreased in both groups and by 1.41 ± 2.95° in Group I and 1.37 ± 3.41° in Group II. The increase in intergonial width between T1 and T0 was negatively correlated with the preoperative mandibular angle (P = 0.003) and positively correlated with the transverse outward movement of the proximal segment (P < 0.001). After surgery, the intergonial width increased and the inferior and posterior border of the proximal segment flared outward. The changes in intergonial width and mandibular angle were mainly related to the rotation of the proximal segment, which has a certain impact on the aesthetics of the lower face. Therefore, controlling the position of the proximal segment is of vital importance to lessen the changes in the mandibular angle area.Level of Evidence III. This journal requires that authors assign a level of evidence to each article. For a full description of these Evidence-Based Medicine ratings, please refer to the Table of Contents or the online Instructions to Authors www.springer.com/00266 .

Determining the safety margin of mandibular lingula in sagittal split ramus osteotomy.

PURPOSE: The anatomical position of the lingula is clinically very important to prevent injuries during sagittal split ramus osteotomy. Our study aims to evaluate the localisation of the lingula by cone beam computed tomography (CBCT) and to compare the localisation of the lingula between malocclusion, gender, and lingula types. METHODS: A retrospective study was conducted to evaluate the shape and location of the lingula using CBCT. A total of 250 CBCT images were included in this study. The lingula was classified as nodular, assimilated, truncated, or triangular type. Six defined distances from the top of the lingula were measured: anterior border of the ramus (L-A), posterior border of the ramus (L-P), internal oblique ridge (L-IOR), mandibular notch (L-N), and distal surface of the mandibular second molar (L-M2) and occlusal plane (L-OP). The measured distances were compared between gender, malocclusion, and lingula types. RESULTS: The most common type of lingula was nodular (32.4%). The L-N, L-P, L-M2, and L-OP distances between genders were statistically higher in male patients than in female patients. The L-IOR, L-M2, and L-OP distances exhibited statistically significant differences found between malocclusions. No statistically significant difference was found when the distances of the lingula to the anatomical points were compared between the lingula types. CONCLUSION: These variations in positioning of the lingula depending on the dysmorphoses are developing towards a systematic 3D examination before any mandibular osteotomy to precisely visualize the position and shape of the lingula.

Effects of sagittal split Ramus osteotomy on condylar position and Ramal orientation in patients with mandibular asymmetry.

OBJECTIVE: The purpose of this study is to assess the impact of Sagittal Split Ramus Osteotomy (SSRO) on the alignment of the condyle and orientation of the Ramal segment following surgery in patients operated for the correction of mandibular asymmetry. METHODS: A total of 27 patients who underwent SSRO were enrolled in this study, and study groups were defined as asymmetric (study group) and symmetric (control group) using linear measurements from the dental midline based on a three-dimensional coordinate system. Differences on preoperative and postoperative values of anterior (AJS), posterior (PJS) and superior joint spaces (SJS), condylar axial angle (CAA), Sagittal Ramal Angle (SRA), and Coronal Ramal Angles (CRA) of study and control groups were measured and compared. The data was analyzed using the "Wilcoxon signed-ranks test" to identify differences between groups. RESULTS: Differences between preoperative and postoperative values of CRA and SRA of the contralateral group showed statistically significant results with p-values of 0.007 and 0.005, respectively. A statistically significant change in CAA angle was found in the control and deviation groups (p = 0.018 and p = 0.010, respectively). CONCLUSIONS: SSRO has inevitable effects on the condylar and ramal orientation. Individuals with asymmetry require particular attention throughout the planning process and beyond. Conjunctive modalities and modifications should be considered and utilized when necessary. Future studies with larger sample sizes, homogenous follow-up periods, and more comprehensive clinical data are needed to substantiate understanding of the response of the condylar segment. CLINICAL RELEVANCE: Orthognathic surgeries inevitably alter the alignment and harmony of temporomandibular structures and may result in change of AJS, PJS, SJS, CAA, SRA, and LRA, which may change the biomechanics of joint and lead to several complications like temporomandibular disorders. Especially in cases with midline asymmetry needs special consideration from planning till the end of the treatment to achieve best results. In severe cases, conjunctive modalities and modifications and other alternatives such as inverted-L osteotomies should be considered.

Comparison of the quality of life changes of patients receiving sagittal split ramus osteotomy or intraoral vertical subsigmoid osteotomy for mandibular prognathism.

OBJECTIVE: To investigate and compare the effect of two orthognathic procedures for mandibular setback, namely, sagittal split ramus osteotomy (SSRO) and intraoral vertical ramus osteotomy (IVRO), on oral health, mental- and physical health-related quality of life across time. MATERIALS AND METHODS: Patients with mandibular prognathism and planned for orthognathic surgery were recruited in this study. Patients were randomized into two groups (IVRO and SSRO groups). Quality of life (QoL) was assessed with the 14-item Short-Form Oral Health Impact Profile (OHIP-14) and the 36-item Short-Form Health Survey (SF-36) preoperatively (T0), postoperative 2 weeks (T1), 6 weeks (T2), 3 months (T3), 6 months (T4), 12 months (T5), and 24 months (T6). A comparison of OHIP-14 and SF-36 scores between two groups was conducted. RESULTS: Ninety-eight patients (49 SSRO group, 49 IVRO group) participated in this study. There was no significant difference in OHIP-14 scores between SSRO and IVRO throughout the treatment process. SSRO group had significant reduction of OHIP-14 score (i.e., improving oral health-related QoL) since postoperative 2 weeks, whereas IVRO group had significant reduction since postoperative 6 weeks. Starting from postoperative 3 months, the oral health-related QoL of both groups was already significantly better than the baseline level and continued to steadily improve afterwards. For SF-36, both groups had increased physical health summary score starting from postoperative 2 weeks, indicating an early and gradual recovery of physical health-related QoL. The mental health summary score of the SSRO group began to increase from postoperative 2 weeks, but that of the IVRO group only began to increase from postoperative 6 weeks. Patient age at the time of surgery was positively correlated with OHIP scores in the postoperative period. CONCLUSIONS: The study concludes that both SSRO and IVRO contributed to the improvement of QoL in the long term, but oral health- and mental health-related QoL of SSRO groups showed earlier improvement. CLINICAL RELEVANCE: Undergoing orthognathic surgery at early ages is advised, as older age of patients appeared to have worse QoL. TRIAL REGISTRATION: Clinical trial registration number: HKUCTR-1985. Date of Registration: 14 Apr 2015.

Modeling the effect of bilateral sagittal split osteotomy on posterior, superior and medial space dimensions of the temporomandibular joint: a retrospective controlled cohort study.

BACKGROUND: To model the effect of isolated bilateral sagittal split osteotomy (BSSO) on changes in posterior (PSD), superior (SSD), and medial space dimensions (MSD) of the temporomandibular joint. METHODS: Using a retrospective cohort study design, pre- and postoperative (immediately after surgery; 1 year follow-up) cone-beam computed tomography measurements of 36 patients who had undergone BSSO for mandibular advancement were compared with a control group of 25 subjects from whom a mandibular odontogenic cyst was removed under general anesthesia. Generalized estimation equation (GEE) models were used to examine the independent effects of study group, preoperative condylar position, and time points on PSD, SSD, and MSD adjusting for covariates (age, sex, and mandibular advancement). RESULTS: No significant differences were found regarding changes in PSD (p = 0.144), SSD (p = 0.607), or MSD (p = 0.565) between the BSSO and control groups. However, the preoperative posterior condylar position showed significant effects on PSD (p < 0.001) and MSD (p = 0.043), while the preoperative central condylar position demonstrated a significant effect on PSD (p < 0.001). CONCLUSION: The data suggest that preoperative posterior condylar position is a significant effect modifier of PSD and MSD over time in this cohort.

Risk Factors Analysis for Different Types of Unfavorable Fracture Patterns During Sagittal Split Ramus Osteotomy: A Retrospective Study of 2008 Sides.

PURPOSE: To summarize unfavorable fracture patterns during sagittal split ramus osteotomy (SSRO) and investigate the association with influencing factors. MATERIALS AND METHODS: We conducted a retrospective analysis of 1007 patients with 2008 sides of SSRO and classified unfavorable fracture patterns into three types: fracture lines involving the sigmoid notch, condylar process, or coronoid process (Type A); fracture lines extending from the posterior border of the mandibular ramus to the mandibular body or the anterior border of the ramus (Type B); and unfavorable fractures located in the anterior horn of the proximal segment with free fragment (Type C). Logistic regression analysis was used to evaluate factors influencing unfavorable fracture patterns, including sex, age at the time of operation, class of occlusion, presence of the third molar, uni- or bi-maxillary surgery, and the distance from the mandibular canal to the buccal cortex. RESULTS: The distance from the mandibular canal to the buccal cortex was significantly associated with unfavorable fracture patterns during SSRO. The presence of third molars was significantly associated with Type A fractures. The distance from the mandibular canal to the buccal cortex was significantly lower in Type B fractures. CONCLUSION: We found that the influencing factors for unfavorable fracture patterns varied. Clinicians should pay specific attention to patients with factors for each unfavorable fracture pattern during SSRO. LEVEL OF EVIDENCE IV: This journal requires that authors assign a level of evidence to each article. For a full description of these Evidence-Based Medicine ratings, please refer to the Table of Contents or the online Instructions to Authors www.springer.com/00266 .

Quantitative sensory testing of mandibular somatosensory function following orthognathic surgery-A pilot study in Chinese with class III malocclusion.

BACKGROUND: Somatosensory changes after sagittal split ramus osteotomy (SSRO) have not been fully studied in Chinese patients by the latest technologies. OBJECTIVE: To provide a comprehensive analysis of somatosensory function at the lower lip and chin at different time points following SSRO in a Chinese population. METHODS: A total of 22 patients (18-27 years; nine men) with skeletal III malocclusion and scheduled for SSRO were recruited. Quantitative sensory testing (QST) was performed at pre-operation (baseline), 1 week (1W), 1, 3 and 6 months (1M, 3M, 6M) post-operatively. Cold detection threshold (CDT), warm detection threshold (WDT), cold pain threshold (CPT), heat pain threshold (HPT), mechanical detection threshold (MDT), mechanical pain threshold (MPT), pressure pain threshold (PPT) and two-point discrimination threshold (2PD) were tested at the lower lip and chin. RESULTS: Except for PPT at both test sides at 1W and 1M, all QST values indicated a significantly reduced sensitivity (p < .05). All values had returned to baseline values at 3M with exception of HPT at the right chin which, however, had recovered at 6M (p > .05). CONCLUSIONS: Somatosensory function at the lower lip and chin appears to be fully recovered in the majority of young Chinese adults 6 months after SSRO for skeletal class III malocclusion.

Postoperative CT findings of orthognathic surgery and its complications: A guide for radiologists.

Orthognathic surgery is the standard procedure to correct congenital, developmental, or acquired dentofacial deformities. The maxillomandibular relationship corrected by orthognathic surgery can improve facial esthetics, masticatory function, articulation, and breathing. The most common types of osteotomies include the combination of Le Fort I osteotomy, bilateral sagittal split mandibular ramus osteotomy, and genioplasty. High-resolution low-dose computed tomography is useful for evaluating the facial skeleton and soft tissues after surgery as well as for depicting a variety of possible complications. This article reviews the postoperative imaging findings of the most common orthognathic surgeries and their potential complications on multidetector-row computed tomography.

Importance in the occurrence rate of shortest buccal bone marrow distance (<1 mm) for sagittal split ramus osteotomy.

BACKGROUND/PURPOSE: The neurosensory disturbance is a common complication following sagittal split ramus osteotomy (SSRO) whereas the shortest buccal bone marrow (SBM) is an important risk factor. The present study aimed to investigate the relationship between the occurrence rates of SBM among three skeletal patterns. METHODS: The cone-beam computed tomography (CBCT) images of 90 participants were divided into skeletal Class I, II, and III. There were six horizontal planes separated apart by a 2 mm interval; it started with plane 0 (original intact mandibular canal) to plane 5 which was 10 mm below. The data of SBM were divided into two groups (SBM ≥ 1 mm and SBM < 1 mm). With an SBM value < 1 mm, we defined a high occurrence rate of postoperative neurosensory abnormality or unfavorable split. RESULTS: The Class III patients had the smallest SBM value (1.31-1.75 mm) whereas the Class II patients had the largest SBM value (1.57-2.09 mm). For the Class III patients, the highest and lowest occurrence rates of SBM were 56.5% and 43.5% respectively. For the Class II patients, the highest and lowest occurrence rates of SBM were 37.1% and 17.7% respectively. The patients with Class III malocclusion had higher occurrence rates of SBM than the patients with Class II malocclusion. CONCLUSION: Class III had a significantly higher occurrence of probability (SBM < 1 mm) than Class II. Therefore, patients with Class III were more likely to experience postoperative neurosensory abnormalities and unfavorable split than patients with Class II.

Evaluation of the Therapeutic Effect of Bi-Maxillary Osteotomy Using the Stress Distribution on the Temporomandibular Joint When Doing Anterior Teeth Occlusion.

The purpose of this study was to investigate how sagittal split ramus osteotomy (SSRO) and Le Fort 1 osteotomy affected the stress distribution of the temporomandibular joint (TMJ) during an anterior teeth bite using the three-dimensional (3D) finite element (FE) method. Fourteen orthognathic surgery patients were examined with mandibular prognathism, facial asymmetry, and mandibular retraction. They underwent Le Fort 1 osteotomy in conjunction with SSRO. In addition, ten asymptomatic subjects were recruited as the control group. The 3D models of the mandible, disc, and maxilla were reconstructed according to cone-beam computed tomography (CBCT). Contact was used to simulate the interaction of the disc-condyle, disc-temporal bone, and upper-lower dentition. Muscle forces and boundary conditions corresponding to the anterior occlusions were applied on the models. The stresses on the articular disc and condyle in the pre-operative group were significantly higher than normal. The contact stress and minimum principal stress in TMJ for patients with temporomandibular disorder (TMD) were abnormally higher. The peak stresses of the TMJ of the patients under anterior occlusions decreased after bimaxillary osteotomy. No postoperative TMD symptoms were found. Maxillofacial deformity led to excessive stress on the TMJ. Bimaxillary osteotomy can partially improve the stress distributions of the TMJ and relieve the symptoms of TMD.

Facial profile and frontal changes after bimaxillary surgery in patients with mandibular prognathism.

BACKGROUND/PURPOSE: Patients are always concerned about their postoperative appearance before surgery for facial deformity correction. The present study investigated the facial profile and frontal changes following two-jaw surgery. METHODS: Forty patients who underwent two-jaw surgery were divided by the amount of mandibular setback (group I: ≤8 mm and group II: >8 mm). Cephalometric radiograms (lateral and frontal) were collected and analyzed at three intervals: preoperatively (T1), immediately postoperatively (T2), and final follow-up (T3). The following points were identified: cheek points (C1-C5), pronasale (Prn, tip of the nose), anterior nasal spine (ANS), subnasal (Sn), point A, labrale superius (Ls), incision superius (Is), labrale inferius (Li), incision inferius (Ii), point B, labiomental sulcus (Si), pogonion (Pog), soft tissue pogonion (PogS), ramus point (RP), and gonion (Go). The immediate postoperative changes (T21), final postoperative changes (T32), and final stability (T31) were calculated and analyzed. RESULTS: In T31, the cheek line showed significant advancements of 2.3 mm (group I) and 1.6 mm (group II). The soft:hard tissue ratios were significantly correlated: Prn:ANS (0.37:1), Prn:A (0.39:1), Sn:A (0.85:1), C3:A (0.82:1), Ls:Is (0.92:1), Li:Ii (0.91:1), Si:B (0.88:1), and PogS:Pog (group I, 0.78:1 and group II, 0.93:1). The intercondylion and intergonial widths of group II (T31) significantly increased 1.8 and 4 mm, respectively. Regarding the postoperative skeletal stability (T32), group I showed significant correlations between amounts of mandibular setback, but group II did not. CONCLUSION: In the facial profile, the cheek line showed significant advancement postoperatively. The frontal mandibular transverse dimensions were significantly increased.

Three-dimensional Finite Element Analysis of Bone Fixation in Bilateral Sagittal Split Ramus Osteotomy Using Individual Models.

The purpose of this study was to investigate factors involved in stress on locking mini-plate/screws used in orthognathic surgery based on patient-specific 3-dimensional finite element analysis. Data were obtained from 10 patients undergoing mandibular advancement by bilateral sagittal split ramus osteotomy. All underwent osteosynthesis with 2.0-mm titanium locking mini-plate/screws. A 3-dimensional finite element model of the mandible was created for each patient and each model subjected to the same loading conditions, which produced different stress values on locking mini-plate/screws. When the contact area of the proximal and distal bone segments was narrower and bone mineral density (BMD) lower, the von Mises stress values on the plate/screws were higher (contact area, p<0.01; BMD, p<0.05). The present results suggest that bone contact area and BMD should be considered as plate stress factors.

Tongue-palatal contact changes in patients with skeletal mandibular prognathism after sagittal split ramus osteotomy: an electropalatography study.

The purpose of this study was to investigate the changes in tongue-palatal contact patterns using electropalatography (EPG) before and after sagittal split ramus osteotomy (SSRO) in patients with mandibular prognathism. Nine clients who underwent SSRO for mandibular setback and seven control subjects were participated in this study. Tongue-palatal contact patterns for /t/, /s/ and /k/ production were investigated using EPG before surgery and 3 months after surgery. The mean value of whole total of palate contact (WT) in the maximum contact frame was examined before and after SSRO. The correlation quantity between the change of center of gravity (COG) value and the amount of mandibular setback was also evaluated. The mean value of WT for /t/ and /s/ significantly increased after SSRO, and the EPG pattern became normal. However, a remarkable change in WT for /k/ was not observed, and the mean value was significantly larger in the SSRO group before and after surgery than in the control group. A negative correlation between COG variation and the amount of mandibular setback for /t/ and positive correlation for /s/ was observed. This study demonstrated that tongue-palatal contact patterns for /t/ and /s/ articulation improved clearly after SSRO. There was a significant correlation between COG variation and the amount of mandibular setback. However, no significant change was detected through perceptual assessment before and after SSRO. Further investigation is needed to determine whether these results will change over time.

Anatomical position of the mandibular canal in relation to the buccal cortical bone in Chinese patients with different dentofacial relationships.

BACKGROUND/PURPOSE: The purpose of this study was to determine the position of the mandibular canal in relation to the buccal cortical bone in Chinese patients with three dentofacial relationships: normal dentition, retrognathism, and prognathism. METHODS: Cone-beam computed tomography and lateral cephalograms of patients with normal dentation, retrognathism, and prognathism (n = 32 each group) were reviewed. Measurements of the shortest distance from the outer/buccal edge of the mandibular canal to the inner surface of the buccal cortex, and the distance from the lingula of the ramus to the dorsal root of the first molar were recorded. RESULTS: No significant difference was observed between the three groups in the distribution of contact or fusion of the mandibular canal, or in the course of the mandibular canal on the right or left side. When the shortest distance at the lingula on the left side was >2.1 mm, no instances of contact or fusion were observed. On the right side, 100% of the patients had no contact or fusion when the shortest distance was >2.7 mm at the lingula. CONCLUSION: The shortest distance from the outer/buccal edge of the mandibular canal to the inner surface of the buccal cortex measured at the lingula can predict contact or fusion. During sagittal split ramus osteotomy, great care should be observed at the point halfway between the lingula and the anterior ramus border where the inferior alveolar nerve is the closest to the cortical bone.

Evaluation of different screw fixation techniques and screw diameters in sagittal split ramus osteotomy: finite element analysis method.

Sagittal split ramus osteotomy (SSRO) is used for correction of numerous congenital or acquired deformities in facial region. Several techniques have been developed and used to maintain fixation and stabilisation following SSRO application. In this study, the effects of the insertion formations of the bicortical different sized screws to the stresses generated by forces were studied. Three-dimensional finite elements analysis (FEA) and static linear analysis methods were used to investigate difference which would occur in terms of forces effecting onto the screws and transmitted to bone between different application areas. No significant difference was found between 1·5- and 2-mm screws used in SSRO fixation. Besides, it was found that 'inverted L' application was more successful compared to the others and that was followed by 'L' and 'linear' formations which showed close rates to each other. Few studies have investigated the effect of thickness and application areas of bicortical screws. This study was performed on both advanced and regressed jaws positions.