A Dual-Polythiophene Blending Strategy to Reduce the Efficiency-Stability-Cost Gap of Solar Cells.

Benefiting from the photovoltaic material innovation and delicate device optimization, high-efficiency solar cells employing polymeric materials are thriving. Reducing the gap of cost, efficiency, and stability is the critical challenge faced by the emerging solar cells such as organics, quantum dots and perovskites. Poly(3-alkylthiophene) demonstrates great potential in organic solar cells and quantum dot solar cells as the active layer or the hole transport layer due to its large scalability, excellent photoelectric performance, and favorable hydrophobicity. The present low efficiency and insufficient stability, restrict its commercial application. In this work, a facile strategy of blending two simple polythiophenes is put forward to manipulate the film microstructure and enhance the device efficiency and thermal stability of solar cells. The introduction of P3PT can improve the power conversion efficiency (PCE) of a benchmark cost-effective blend P3HT:O-IDTBR to 7.41%, and the developed ternary solar cells also exhibit increased thermal stability. More strikingly, the quantum dot solar cells with the dual-polythiophene hole transport layer achieve the highest PCE of 10.51%, which is among the topmost efficiencies for quantum dots/polythiophene solar cells. Together, this work provides an effective route to simultaneously optimize the device efficiency and thermal stability of solar cells.

Influence of Block Ratio on Thermal, Optical, and Photovoltaic Properties of Poly(3-hexylthiophene)-b-poly(3-butylthiophene)-b-poly(3-octylthiophene).

Efforts to improve the solar power conversion efficiencies of binary bulk heterojunction-type organic photovoltaic devices using an active layer consisting of a poly-(3-alkylthiophene) (P3AT) homopolymer and a suitable fullerene derivative face barriers caused by the intrinsic properties of homopolymers. To overcome such barriers, researchers might be able to chemically tailor homopolymers by means of monomer ratio-balanced block copolymerization to obtain preferable properties. Triblock copolymers consisting of three components-3-hexylthiophene (HT), 3-butylthiophene (BT), and 3-octylthiophene (OT)-were synthesized via Grignard metathesis (GRIM) polymerization. The component ratios of the synthesized block copolymers were virtually the same as the feeding ratios of the monomers, a fact which was verified using 1H-NMR spectra. All the copolymers exhibited comparable crystalline and melting temperatures, which increased when one type of monomer became dominant. In addition, their power conversion efficiencies and photoluminescence properties were governed by the major components of the copolymers. Interestingly, the HT component-dominated block copolymer indicated the highest power conversion efficiency, comparable to that of its homopolymer, although its molecular weight was significantly shorter.

Kelvin Probe Microscopy Investigation of Poly-Octylthiophene Aggregates.

Conductive polymers have fundamental relevance as well as novel technological applications in the organic optoelectronics field. Their photophysical and transport properties strongly depend on the molecular arrangement, and nanoscale characterization is needed to fully understand the optoelectronic processes taking place in organic devices. In this work, we study the electrostatic properties of poly-3-octylthiophene isolated structures: disordered low-packed polymer chains and crystalline layered lamellar assemblies. We characterize the electronic ground state using Kelvin probe microscopy. This allows us to resolve a rich variety of surface potential regions that emerge over the different polymer structures. These SP regions are correlated with different molecular aggregates.

Effects of Chain Orientation in Self-Organized Buffer Layers Based on Poly(3-alkylthiophene)s for Organic Photovoltaics.

Surface-segregated monolayers (SSMs) based on two poly(3-alkylthiophene)s with semifluoroalkyl groups at either the side chains (P3DDFT) or one end of the main chain (P3BT-F17) were used as self-organized buffer layers at the electrode interfaces in bulk heterojunction (BHJ) organic photovoltaic devices. Both of the SSMs greatly shifted the vacuum levels of the BHJ films at the surface due to the aligned permanent dipole moments of the semifluoroalkyl chains. Hole extraction in the BHJ of poly(3-hexylthiophene) (P3HT):[6,6]-phenyl C61-butyric acid methyl ester (PCBM) became more efficient in the presence of the P3DDFT buffer layer, resulting in an improved power conversion efficiency. In contrast, the SSM of P3BT-F17 induced changes in the chain orientation of P3HT and the morphology of the BHJ films, resulting in decreased performance. These results indicate that the molecular design of polymer-based SSMs can affect not only the energy structure at the interface but also the morphology and the molecular orientations in the BHJs.

The Impact of Polymer Dynamics on Photoinduced Carrier Formation in Films of Semiconducting Polymers.

A better understanding of the carrier formation process in photosemiconducting polymers is crucial to design and construct highly functionalized thin film organic photodevices. Almost all studies published focus on the effect of structure on the photoinduced carrier formation process. Here, we study the dynamics of polymer chain impacts on the carrier formation process for a series of poly(3-alkylthiophene)s (P3ATs) with different alkyl side-chain lengths. The formation of polarons (P) from polaron pairs (PP) was accelerated at a temperature at which the twisting motion of thiophene rings occurs. Among all P3ATs employed, in P3AT with hexyl groups, or poly(3-hexylthiophene) (P3HT), it was easiest to twist the thiophene rings and generate P from PP. The activation energy for P formation was proportional to that of thiophene ring motion. This makes it clear that chain dynamics, in addition to the crystalline structure, is a controlling factor for the carrier formation process in photosemiconducting polymers.

Side group of poly(3-alkylthiophene)s controlled dispersion of single-walled carbon nanotubes for transparent conducting film.

Controlled dispersion of single-walled carbon nanotubes (SWCNTs) in common solvents is a challenging issue, especially for the rising need of low cost flexible transparent conducting films (TCFs). Utilizing conductive polymer as surfactant to facilitate SWCNTs solubility is the most successful pragmatic approach to such problem. Here, we show that dispersion of SWCNT with polymer significantly relies on the length of polymer side groups, which not only influences the diameter distribution of SWCNTs in solution, also eventually affects their effective TCF performance. Surfactants with longer side groups covering larger nanotube surface area could induce adequate steric effect to stabilize the wrapped SWCNTs against the nonspecific aggregation, as discerned by the optical and microscopic measurements, also evidenced from the resultant higher electrokinetic potential. This approach demonstrates a facile route to fabricate large-area SWCNTs-TCFs exhibiting high transmittance and high conductivity, with considerable uniformity over 10 cm × 10 cm.