Shape-Tunable BaTiO3 Crystals Presenting Facet-Dependent Optical and Piezoelectric Properties.

BaTiO3 octahedra, edge-, and corner-truncated cubes, and cubes with four tunable sizes from 132 to 438 nm are synthesized by a solvothermal growth approach. Acetic acid treatment can cleanly remove BaCO3 impurity. Rietveld refinement of X-ray diffraction patterns and Raman spectra help to confirm the particles have a tetragonal crystal structure. The crystals also exhibit size- and facet-dependent bandgap shifts. BaTiO3 octahedra show larger piezoelectric, ferroelectric, and pyroelectric effects than truncated cubes and cubes. The measured dielectric constant differences should be associated with their various facet-dependent behaviors. Piezoelectric nanogenerators fabricated from BaTiO3 octahedra consistently show the best performance than those containing truncated cubes and cubes. In particular, a nanogenerator with 30 wt.%-incorporated octahedra displays an open-circuit voltage of 23 V and short-circuit current of 324 nA. The device performance is also highly stable. The maximum output power reaches 3.9 µW at 60 MΩ. The fabricated nanogenerator can provide sufficient electricity to power light-emitting diodes. This work further demonstrates that various physical properties of semiconductor crystals show surface dependence.

Polarization-Dependent Large Photorefractive Effect In A Wide Bandgap 2D Metal Halide Ferroelectric.

Photorefractive effect of ferroelectrics refers to the light-induced change of refractive index, which is an optical controlling avenue in holographic storage and image processing. For most ferroelectrics, however, the small photorefractive effect (10-5 -10-4 ) hinders their practical application and it is urgent to exploit new photorefractive system. Here, for the first time, strong photorefractive effects are achieved in a 2D metal-halide ferroelectric, [CH3 (CH2 )3 NH3 ]2 (CH3 NH3 )Pb2 Cl7 (1), showing large spontaneous polarization (≈4.1 µC cm-2 ) and wide optical bandgap (≈3.20 eV). Notably, under light irradiation, 1 enables a large variation of refractive indices up to ≈ 1× 10-3 , being one order higher than the existing materials and comparable to the state-of-the-art inorganic ferroelectrics. This intriguing photorefractive behavior involves with the sharp variation of polarization caused by photo-pyroelectricity. As the first report of 2D metal-halide photorefractive ferroelectric, this work sheds light on optical controlling of physical properties in electric-ordered materials.

Low-Energy Photons Dual Harvest for Photocatalytic Hydrogen Evolution: Bimodal Surface Plasma Resonance Related Synergism of Upconversion and Pyroelectricity.

Utilization of low-energy photons for efficient photocatalysis remains a challenging pursuit. Herein, a strategy is reported to boost the photocatalytic performance, by promoting low-energy photons dual harvest through bimodal surface plasmon resonance (SPR)-enhanced synergistically upconversion and pyroelectricity. It is achieved by introducing triplet-triplet annihilation upconversion (TTA-UC) materials and plasmonic material (Au nanorods, AuNRs) into composite fibers composed of pyroelectric substrate (poly(vinylidene fluoride)) and photocatalyst Cd0.5 Zn0.5 S. Interestingly, the dual combination of TTA-UC and AuNRs SPR in the presence of polyvinylidene fluoride substrate with pyroelectric property promotes the photocatalytic hydrogen evolution performance by 2.88 folds with the highest average apparent quantum yield of 7.0% under the low-energy light (λ > 475 nm), which far outweighs the role of separate application of TTA-UC (34%) and AuNRs SPR (76%). The presence of pyroelectricity plays an important role in the built-in electric field as well as the accordingly photogenerated carrier behavior in the composite photocatalytic materials, and the pyroelectricity can be affected by AuNRs with different morphologies, which is proved by the Kelvin probe force microscopy and photocurrent data. This work provides a new avenue for fully utilizing low-energy photons in the solar spectrum for improving photocatalytic performance.

Harvesting microwave energy using pyroelectricity of nanostructured graphene/zirconium-doped hafnium oxide ferroelectric heterostructures.

In this work, we present the design, atomistic/circuit/electromagnetic simulations, and the experimental results for graphene monolayer/zirconium-doped hafnium oxide (HfZrO) ultra-thin ferroelectric-based field effect transistors fabricated at the wafer scale, regarding the pyroelectricity generation directly from microwave signals, at room temperature and below it, namely at 218 K and at 100 K. The transistors work like energy harvesters, i.e. they collect low-power microwave energy and transform it into DC voltages with a maximum amplitude between 20 and 30 mV. The same devices function as microwave detectors in the band 1-10.4 GHz and at very low input power levels not exceeding 80µW when they are biased by using a drain voltage, with average responsivity values in the range 200-400 mV mW-1.

Centimeter-Size Single Crystals of Halide Perovskite Photoferroelectric Solid Solution with Ultrahigh Pyroelectricity Boosted Photodetection.

Photoferroelectrics, especially emerging halide perovskite ferroelectrics, have motivated tremendous interests owing to their fascinating bulk photovoltaic effect (BPVE) and cross-coupled functionalities. However, solid solutions of halide perovskite photoferroelectrics with controllable structure and enhanced performance are scarcely explored. Herein, through mixing cage cation, a homogeneous halide perovskite photoferroelectric PA2 FAx MA1-x Pb2 Br7 solid solution (PA, FA and MA are CH3 CH2 CH2 NH3 + , NH2 CHNH2 + and CH3 NH3 + , 0≤x≤1) has been developed, which demonstrates tunable Curie temperature in a wide range of 263-323 K and excellent optoelectrical features. As the component adjusted to x=0.7, the bulk crystal demonstrates ultrahigh pyroelectric coefficient up to 1.48 µC cm-2 K-1 around room temperature. Strikingly, benefiting from the light-induced pyroelectricity and remarkable BPVE, a self-powered and sensitive photodetector based solid solution crystals with boosted responsivity and detectivity over than 1300 % has been achieved. This pioneering work sheds light on the exploration of photoferroelectric solid solutions towards high-performance photoelectronic devices.

Engineering of Pyroelectric Crystals Decoupled from Piezoelectricity as Illustrated by Doped α-Glycine.

Design of pyroelectric crystals decoupled from piezoelectricity is not only a topic of scientific curiosity but also demonstrates effects in principle that have the potential to be technologically advantageous. Here we report a new method for the design of such materials. Thus, the co-doping of centrosymmetric crystals with tailor-made guest molecules, as illustrated by the doping of α-glycine with different amino acids (Threonine, Alanine and Serine). The polarization of those crystals displays two distinct contributions, one arising from the difference in dipole moments between guest and host and the other from the displacement of host molecules from their symmetry-related positions. These contributions exhibit different temperature dependences and response to mechanical deformation. Thus, providing a proof of concept for the ability to design pyroelectric materials with reduced piezoelectric coefficient (d22 ) to a minimal value, below the resolution limit of the method (<0.005 pm/V).

Catalytic Applications of Non-Centrosymmetric Oxide Nanomaterials.

Noble-metal-free catalytic nanoparticles hold the promise being abundant, low-cost materials having a small environmental footprint and excellent performance, albeit inferior to that of noble metal counterparts. Several materials have a long-standing history of success in photocatalysis, in particular titanium dioxide, and in recent years more complex oxides and added functionality have emerged with enhanced performance. We will discuss different approaches related to the use of non-centrosymmetric and polar oxide nanoparticles and how the bulk photovoltaic effect, piezoelectricity, and pyroelectricity add to photocatalysis and tribocatalysis. We pay special attention to discriminate between the role of free versus that of bound charges within the catalyst, which is crucial to disentangle the different contributions to the catalytic reaction for the benefit of the overall enhanced catalytic performance in e.g. wastewater treatment and ultimately water-splitting.

Tetragonal CH3NH3PbI3 is ferroelectric.

Halide perovskite (HaP) semiconductors are revolutionizing photovoltaic (PV) solar energy conversion by showing remarkable performance of solar cells made with HaPs, especially tetragonal methylammonium lead triiodide (MAPbI3). In particular, the low voltage loss of these cells implies a remarkably low recombination rate of photogenerated carriers. It was suggested that low recombination can be due to the spatial separation of electrons and holes, a possibility if MAPbI3 is a semiconducting ferroelectric, which, however, requires clear experimental evidence. As a first step, we show that, in operando, MAPbI3 (unlike MAPbBr3) is pyroelectric, which implies it can be ferroelectric. The next step, proving it is (not) ferroelectric, is challenging, because of the material's relatively high electrical conductance (a consequence of an optical band gap suitable for PV conversion) and low stability under high applied bias voltage. This excludes normal measurements of a ferroelectric hysteresis loop, to prove ferroelectricity's hallmark switchable polarization. By adopting an approach suitable for electrically leaky materials as MAPbI3, we show here ferroelectric hysteresis from well-characterized single crystals at low temperature (still within the tetragonal phase, which is stable at room temperature). By chemical etching, we also can image the structural fingerprint for ferroelectricity, polar domains, periodically stacked along the polar axis of the crystal, which, as predicted by theory, scale with the overall crystal size. We also succeeded in detecting clear second harmonic generation, direct evidence for the material's noncentrosymmetry. We note that the material's ferroelectric nature, can, but need not be important in a PV cell at room temperature.

Heterogeneous Electrofreezing Triggered by CO2 on Pyroelectric Crystals: Qualitatively Different Icing on Hydrophilic and Hydrophobic Surfaces.

By performing icing experiments on hydrophilic and hydrophobic surfaces of pyroelectric amino acids and on the x-cut faces of LiTaO3 , we discovered that the effect of electrofreezing of super cooled water is triggered by ions of carbonic acid. During the cooling of the hydrophilic pyroelectric crystals, a continuous water layer is created between the charged hemihedral faces, as confirmed by impedance measurements. As a result, a current of carbonic acid ions, produced by dissolved environmental CO2 , flows through the wetted layer towards the hemihedral faces and elevates the icing temperature. This proposed mechanism is based on the following: (i) on hydrophilic surfaces, water with dissolved CO2 (pH 4) freezes at higher temperatures than pure water of pH 7. (ii) In the absence of the ionic current, achieved by linking the two hemihedral faces of hydrophilic crystals by a conductive paint, water of the two pH levels freeze at the same temperature. (iii) On hydrophobic crystals with similar pyroelectric coefficients, where there is no continuous wetted layer, no electrofreezing effect is observed.

Heterogeneous Electrofreezing of Super-Cooled Water on Surfaces of Pyroelectric Crystals is Triggered by Trigonal Planar Ions.

Electrofreezing experiments of super-cooled water (SCW) with different ions, performed directly on the charged hemihedral faces of pyroelectric LiTaO3 and AgI crystals, in the presence and in the absence of pyroelectric charge are reported. It is demonstrated that bicarbonate (HCO3 - ) ions elevate the icing temperature near the positively charged faces. In contrast, the hydronium (H3 O+ ) slightly reduces the icing temperature. Molecular dynamics simulations suggest that the hydrated trigonal planar HCO3 - ions self-assemble with water molecules near the surface of the AgI crystal as clusters of slightly different configuration from those of the ice-like hexagons. These clusters, however, have a tendency to serve as embryonic nuclei for ice crystallization. Consequently, we predicted and experimentally confirmed that the trigonal planar ions of NO3 - and guanidinium (Gdm+ ), at appropriate concentrations, elevate the icing temperature near the positive and negative charged surfaces, respectively. On the other hand, the Cl- and SO4 2- ions of different configurations reduce the icing temperature.

Harnessing Plasticity in an Amine-Borane as a Piezoelectric and Pyroelectric Flexible Film.

We demonstrate that trimethylamine borane can exhibit desirable piezoelectric and pyroelectric properties. The material was shown to be able operate as a flexible film for both thermal sensing, thermal energy conversion and mechanical sensing with high open circuit voltages (>10 V). A piezoelectric coefficient of d33 ≈10-16 pC N-1 , and pyroelectric coefficient of p≈25.8 µC m-2 K-1 were achieved after poling, with high pyroelectric figure of merits for sensing and harvesting, along with a relative permittivity of ϵ 33 σ ≈ 6.3.

Solvent-Induced Crystal Polymorphism as Studied by Pyroelectric Measurements and Impedance Spectroscopy: Alcohols as Tailor-Made Inhibitors of α-Glycine.

Metastable polymorphs commonly emerge when the formation of the stable analogues is inhibited by using different solvents or auxiliaries. Herein, we report that when glycine is grown in aqueous solutions in the presence of low concentrations of different co-solvents, only alcohols and acetone, unlike water and acetic acid, are selectively incorporated in minute amounts within the bulk of the α-polymorph. These findings demonstrate that although water binds more strongly to the growing face of the crystal, alcohols and acetone are exclusively incorporated, and thus serve as efficient inhibitors of this polymorph, leading to the precipitation of the ß-form. These solvents then create polar domains detectable by pyroelectric measurements and impedance spectroscopy. These results suggest that in the control of crystal polymorphism with co-solvents, one should consider also the different desolvation rates in addition to the energy of binding to the growing faces of the crystal.

The Contribution of Pyroelectricity of AgI Crystals to Ice Nucleation.

The pyroelectricity of AgI crystals strongly affects the icing temperature of super-cooled water, as disentangled from that of epitaxy. This deduction was achieved by the design of polar crystalline ceramic pellets of AgI, with experimentally determined sense of polarity. These pellets are suitable for measuring both their pyroelectric properties as well as the icing temperature of super-cooled water, separately on each of the expressed Ag+ and I- hemihedral surfaces. The positive pyroelectric charge at the silver-enriched side elevates the icing temperature, whereas the negative charge at the iodide side decreases that temperature. Moreover, the effect of pyroelectric charge remains dominant despite the presence of contaminants on both the silver and the iodide-enriched surfaces. Consequently an electrochemical process for ice nucleation is suggested, which might be of relevance for understanding the role played by electric charges in heterogeneous icing processes in general.

A Strip Cell in Pyroelectric Devices.

The pyroelectric effect affords the opportunity to convert temporal temperature fluctuations into usable electrical energy in order to develop abundantly available waste heat. A strip pyroelectric cell, used to enhance temperature variation rates by lateral temperature gradients and to reduce cell capacitance to further promote the induced voltage, is described as a means of improving pyroelectric energy transformation. A precision dicing saw was successfully applied in fabricating the pyroelectric cell with a strip form. The strip pyroelectric cell with a high-narrow cross section is able to greatly absorb thermal energy via the side walls of the strips, thereby inducing lateral temperature gradients and increasing temperature variation rates in a thicker pyroelectric cell. Both simulation and experimentation show that the strip pyroelectric cell improves the electrical outputs of pyroelectric cells and enhances the efficiency of pyroelectric harvesters. The strip-type pyroelectric cell has a larger temperature variation when compared to the trenched electrode and the original type, by about 1.9 and 2.4 times, respectively. The measured electrical output of the strip type demonstrates a conspicuous increase in stored energy as compared to the trenched electrode and the original type, by of about 15.6 and 19.8 times, respectively.

Pyroelectric Polyelectrolyte Brushes.

Piezo- and pyroelectric materials are of interest, for example, for energy harvesting applications, for the development of tactile sensors, as well as neuromorphic computing. This study reports the observation of pyro- and piezoelectricity in thin surface-attached polymer brushes containing zwitterionic and electrolytic side groups that are prepared via surface-initiated polymerization. The pyro- and piezoelectric properties of the surface-grafted polyelectrolyte brushes are found to sensitively depend on and can be tuned by variation of the counterion. The observed piezo- and pyroelectric properties reflect the structural complexity of polymer brushes, and are attributed to a complex interplay of the non-uniform segment density within these films, together with a non-uniform distribution of counterions and specific ion effects. The fabrication of thin pyroelectric films by surface-initiated polymerization is an important addition to the existing strategies toward such materials. Surface-initiated polymerization, in particular, allows for facile grafting of polar thin polymer films from a wide range of substrates via a straightforward two-step protocol that obviates the need for multistep laborious synthetic procedures or thin film deposition protocols. The ability to produce polymer brushes with piezo- and pyroelectric properties opens up new avenues of application of these materials, for example, in energy harvesting or biosensing.

Magnetron-Sputtered Lead Titanate Thin Films for Pyroelectric Applications: Part 2-Electrical Characteristics and Characterization Methods.

Pyroelectric materials are naturally electrically polarized and exhibits a built-in spontaneous polarization in their unit cell structure even in the absence of any externally applied electric field. These materials are regarded as one of the ideal detector elements for infrared applications because they have a fast response time and uniform sensitivity at room temperature across all wavelengths. Crystals of the perovskite lead titanate (PbTiO3) family show pyroelectric characteristics and undergo structural phase transitions. They have a high Curie temperature (the temperature at which the material changes from the ferroelectric (polar) to the paraelectric (nonpolar) phase), high pyroelectric coefficient, high spontaneous polarization, low dielectric constant, and constitute important component materials not only useful for infrared detection, but also with vast applications in electronic, optic, and MEMS devices. However, the preparation of large perfect and pure single crystals PbTiO3 is challenging. Additionally, difficulties arise in the application of such bulk crystals in terms of connection to processing circuits, large size, and high voltages required for their operation. In this part of the review paper, we explain the electrical behavior and characterization techniques commonly utilized to unravel the pyroelectric properties of lead titanate and its derivatives. Further, it explains how the material preparation techniques affect the electrical characteristics of resulting thin films. It also provides an in-depth discussion of the measurement of pyroelectric coefficients using different techniques.

The effect of Zn doping on the structure, phase transformation and electric properties of 0.5BZT-0.5BCT materials.

In the current study, an improved method of adding Zn ion doping to the 0.5BZT-0.5BCT-based films with high pyroelectric properties was designed. Under different Zn ion doping ratios, the structure, dielectric constant, phase transition relationship and other characteristics of the test product were analyzed experimentally to obtain the optimal ratio parameters. The experimental results demonstrate that the dielectric properties of the 0.5BZT-0.5BCT-xZn-based films proposed in this study can be far superior to those of other films under the optimal preparation process. The optimal dielectric properties and ferroelectric properties are obtained when the doped data are 0.008. Considering the comprehensive dielectric and energy storage capacity, the optimal doping ratio is 0.01, which can take into account dielectric data and energy storage performance. The energy storage density is 1.842 J / c m 3 , and the energy storage efficiency exceeds 30%. From 0 to 0.02, the properties of the material, such as the hysteresis loop and phase transition relationship are excellent. The properties of the materials studied in this study are excellent, and they are excellent candidate materials for the future application of ferroelectric materials, and provide ideas for related work.

Virus-Based Pyroelectricity.

The first observation of heat-induced electrical potential generation on a virus and its detection through pyroelectricity are presented. Specifically, the authors investigate the pyroelectric properties of the M13 phage, which possesses inherent dipole structures derived from the noncentrosymmetric arrangement of the major coat protein (pVIII) with an α-helical conformation. Unidirectional polarization of the phage is achieved through genetic engineering of the tail protein (pIII) and template-assisted self-assembly techniques. By modifying the pVIII proteins with varying numbers of glutamate residues, the structure-dependent tunable pyroelectric properties of the phage are explored. The most polarized phage exhibits a pyroelectric coefficient of 0.13 µC m-2 °C-1 . Computational modeling and circular dichroism (CD) spectroscopy analysis confirm that the unfolding of α-helices within the pVIII proteins leads to changes in phage polarization upon heating. Moreover, the phage is genetically modified to enable its pyroelectric function in diverse chemical environments. This phage-based approach not only provides valuable insights into bio-pyroelectricity but also opens up new opportunities for the detection of various viral particles. Furthermore, it holds great potential for the development of novel biomaterials for future applications in biosensors and bioelectric materials.

Quasi-harmonic approach to evaluate pyroelectric properties in Janus CrSeBr monolayer.

Two-dimensional materials are emerging as promising dielectric materials and have enormous possibilities in wearable micro and nanoelectronics, sensor, and detectors. The theoretical calculation is performed to investigate the pyroelectric coefficient and pyroelectric figure of merit (FOM) of Janus CrSeBr monolayer. Quasi-harmonic approximation (QHA) is used to calculate primary (p1) and secondary (p2) pyroelectric coefficients. Spontaneous polarization is calculated for different temperatures using QHA. Pyroelectric coefficient (1.21 µC m-2 K at 300 K) is obtained for CrSeBr monolayer, which is∼5times higher compared to MoSSe monolayer. A high FOM is found for CrSeBr monolayer(Fv=0.035 m2 C-1),(Fi=1.97 pm V-1). High FOM for voltage responsivity of CrSeBr monolayer could be beneficial for several commercial applications.

A Polymorph of Dipeptide Halide Glycyl-L-Alanine Hydroiodide Monohydrate: Crystal Structure, Optical Second Harmonic Generation, Piezoelectricity and Pyroelectricity.

A polymorph of glycyl-L-alanine HI.H2O is synthesized from chiral cyclo-glycyl-L-alanine dipeptide. The dipeptide is known to show molecular flexibility in different environments, which leads to polymorphism. The crystal structure of the glycyl-L-alanine HI.H2O polymorph is determined at room temperature and indicates that the space group is polar (P21), with two molecules per unit cell and unit cell parameters a = 7.747 Å, b = 6.435 Å, c = 10.941 Å, α = 90°, ß = 107.53(3)°, γ = 90° and V = 520.1(7) Å3. Crystallization in the polar point group 2, with one polar axis parallel to the b axis, allows pyroelectricity and optical second harmonic generation. Thermal melting of the glycyl-L-alanine HI.H2O polymorph starts at 533 K, close to the melting temperature reported for cyclo-glycyl-L-alanine (531 K) and 32 K lower than that reported for linear glycyl-L-alanine dipeptide (563 K), suggesting that although the dipeptide, when crystallized in the polymorphic form, is not anymore in its cyclic form, it keeps a memory of its initial closed chain and therefore shows a thermal memory effect. Here, we report a pyroelectric coefficient as high as 45 µC/m2K occurring at 345 K, one order of magnitude smaller than that of semi-organic ferroelectric triglycine sulphate (TGS) crystal. Moreover, the glycyl-L-alanine HI.H2O polymorph displays a nonlinear optical effective coefficient of 0.14 pm/V, around 14 times smaller than the value from a phase-matched inorganic barium borate (BBO) single crystal. The new polymorph displays an effective piezoelectric coefficient equal to deff=280 pCN-1, when embedded into electrospun polymer fibers, indicating its suitability as an active system for energy harvesting.