Donor acceptor fluorophores: synthesis, optical properties, TD-DFT and cytotoxicity studies.

Donor-π-acceptor (D-π-A) fluorophores consisting of a donor unit, a π linker, and an acceptor moiety have attracted attention in the last decade. In this study, we report the synthesis, characterization, optical properties, TD-DFT, and cytotoxicity studies of 17 near infrared (NIR) D-π-A analogs which have not been reported so far to the best of our knowledge. These fluorophores have chloroacrylic acid as the acceptor unit and various donor units such as indole, benzothiazole, benzo[e]indole, and quinoline. The fluorophores showed strong absorption in the NIR (700-970 nm) region due to their enhanced intramolecular charge transfer (ICT) between chloroacrylic acid and the donor moieties connected with the Vilsmeier-Haack linker. The emission wavelength maxima of the fluorophores were in between 798 and 870 nm. Compound 20 with a 4-quinoline donor moiety showed an emission wavelength above 1000 nm in the NIR II window. The synthesized fluorophores were characterized by 1H NMR and 13C NMR, and their optical properties were studied. Time dependent density functional theory (TD-DFT) calculations showed that the charge transfer occurs from the donor groups (indole, benzothiazole, benzo[e]indole, and quinoline) to the acceptor chloroacrylic acid moiety. Fluorophores with [HOMO] to [LUMO+1] transitions were shown to possess a charge separation character. The cytotoxicity of selected fluorophores, 4, 7, 10 and 12 was investigated against breast cancer cell lines and they showed better activity than the anti-cancer agent docetaxel.

Curing of UV prints - Assessment of possible toxicological hazard for consumers.

In an experimental setting a laboratory analysis of substances migrating from UV prints under mechanical stress into sweat and saliva simulant was performed. The influence of paper type and curing degree on UV prints was investigated. Five substances were identified at concentrations above the limit of detection in the simulants PPG-3 glyceryl triacrylate, ethoxylated trimethylolpropane triacrylate, trimethylolpropane triacrylate, 2/4-isopropylthioxanthone (ITX), and 2,4-diethylthioxanthone (DETX). Migration of the acrylates and photoinitiators into saliva and sweat simulants were increased when the UV inks were printed on uncoated paper in comparison to coated paper. With an exposure scenario considering a person to leaf through 80 pages of UV-printed paper per day while touching each page with a licked fingertip, Risk Characterisation Ratios (RCR) for oral exposure well below 1 were obtained for all five substances indicating no risk for the general population. The three acrylates are classified for skin sensitisation. The migrated amounts per skin surface area of these three were compared with the EC3 value for a hypothetical substance that could be categorised as strong sensitiser (EC3 = 0.1%). The results show that the risk of skin sensitisation even under worst case conditions can be considered as negligible.

NIR Sensitizer Operating under Long Wavelength (1064 nm) for Free Radical Photopolymerization Processes.

Free radical polymerization upon near-infrared (NIR) light is still the subject of intense research efforts and remains a huge challenge particularly for long wavelengths (>1000 nm). In this study, a NIR sensitizer operating upon long wavelength (1064 nm) is proposed for an efficient polymerization of acrylate monomers. A new three-component photoinitiating system is developed comprising the NIR sensitizer in combination with an Iodonium salt (Iod) and an amine. Remarkably, the NIR sensitizer (IR 1064) absorbing strongly in all the near infrared region (700-1200 nm) offers the possibility to use a broad range of irradiation wavelengths, i.e., examples are provided at 785 and 1064 nm. Such long wavelengths are characterized by many advantages such as a deeper penetration of light and therefore a better curing of the monomer but it is also much safer than UV light. Excellent performance is observed for the three-component IR 1064/Iod/Amine system under air: high conversion of acrylate functions associated with a fast polymerization time. The use of IR 1064 as NIR sensitizer with a broad NIR absorption is-to the best of current knowledge-never proposed in the literature. The photoinitiating performances are studied using real-time Fourier transform infrared spectroscopy.

Real-Time Monitoring of Endogenous Cysteine Levels In Vivo by near-Infrared Turn-on Fluorescent Probe with Large Stokes Shift.

Cysteine (Cys), as an important biothiol, plays a major role in many physiological processes like protein synthesis, detoxification and metabolism, and also is closely associated with a variety of diseases; thus the design of novel highly selective and sensitive near-infrared (NIR) fluorescent probes for Cys detection in vivo is of great significance. Herein, we report a selective and sensitive NIR turn-on fluorescent probe (CP-NIR) with large Stokes shift for detecting Cys in vivo. Upon addition of Cys to the solution of the probe, it is absorption wavelength shifts from 550 to 600 nm, accompanying with an obvious enhancement of NIR fluorescence emission centering around 760 nm. This Michael-addition reaction-based probe shows a large Stokes shift (160 nm), low detection limit (48 nM), fast response time, and low toxicity. Moreover, this novel NIR probe with good cell permeability was successfully applied to monitoring endogenous Cys in living cells and in a mouse model.

Visible-light-initiated thiol-acrylate photopolymerization of heparin-based hydrogels.

An in situ heparin-based forming hydrogel that cures under visible-light is formulated using eosin Y as a photoinitiator with triethanolamine as an electron donor to initiate reaction of thiolated-heparin with acrylate-ended poly(ethylene glycol). Formulations and irradiation conditions are presented for control of heparin content (1.6 to 3.3% w/v), modulus (100-10,000 Pa), and gelation time (30-600 s). Encapsulation of 3T3 fibroblasts in the hydrogel gave over 96% viability for all conditions examined. In vitro characterization of epidermal growth factor released from the hydrogel confirmed that the growth factor remains bioactive. The ability to deliver growth factors, fast gelation kinetics under visible light, and independent control of physical and biochemical properties makes this system a promising candidate for use in regenerative medicine. In particular, irradiation conditions that achieve gelation in 150s are compatible with the stringent light exposure limits of the retina, which affords a wide safety margin for use with other tissues.

Influence of ceramic thickness and type on micromechanical properties of light-cured adhesive bonding agents.

OBJECTIVE: The aim of this study was to evaluate the micromechanical properties of different adhesive bonding agents when polymerized through ceramics. MATERIALS AND METHODS: Sixty sound extracted human third molars were selected and the crowns were sectioned perpendicular to the long axis in order to obtain dentin slices to be bonded with one of the following adhesives: Syntac/Heliobond (Ivoclar-Vivadent) or Adper-Scotchbond-1XT (3M-ESPE). The adhesives were cured by using a LED-unit (Bluephase®, Ivoclar Vivadent) with three different curing times (10 s, 20 s and 30 s) under two ceramics (IPS-e.max-Press, Ivoclar-Vivadent; IPS-Empress®CAD, Ivoclar-Vivadent) of different thicknesses (0 mm, 0.75 mm, 2 mm). Thirty groups were included, each containing 60 measurements. Micromechanical properties (Hardness, HV; indentation modulus, E; and creep, Cr) of the adhesives were measured with an automatic microhardness indenter (Fisherscope H100C, Germany). Data were statistically analyzed by using one-way ANOVA and Tukey's post-hoc test, as well as a multivariate analysis to test the influence of the study parameters (SPSS 18.0). RESULTS: Significant differences were observed between the micromechanical properties of the adhesives (p < 0.05). The ceramic type showed the highest effect on HV (Partial-eta squared (η(2)) = 0.109) of the tested adhesives, while E (η(2) = 0.275) and Cr (η(2) = 0.194) were stronger influenced by the adhesive type. Ceramic thickness showed no effect on the E and Cr of the adhesives. CONCLUSIONS: The adhesive bonding agents used in this study performed well by curing through different thicknesses of ceramics. The micromechanical properties of the adhesives were determined by the adhesive type and were less influenced by ceramic type and curing time.

Color stability of sealed composite resin restorative materials after ultraviolet artificial aging and immersion in staining solutions.

STATEMENT OF PROBLEM: The color alteration of resin-based materials is one of the most common reasons to replace esthetic dental restorations. PURPOSE: This study assessed the influence of surface sealant (Biscover) on the color stability of nanofilled (Supreme XT) and microhybrid (Vit-l-escence and Opallis) composite resins after artificial aging. MATERIAL AND METHODS: One hundred disc-shaped (6 × 1.5 mm) specimens were made for each composite resin. After 24 hours, all specimens were polished and sealant was applied to 50 specimens of each material. Baseline color was measured according to the CIE L*a*b* system using a reflection spectrophotometer. Ten specimens of each group were aged for 252 h in an ultraviolet (UV)-accelerated aging chamber or immersed for 4 weeks in cola soft drink, orange juice, red wine staining solutions or distilled water as control. Color difference (ΔE) after aging was calculated based on the color coordinates before (baseline) and after aging/staining treatment. Data were analyzed with 2-way ANOVA and Fisher's test (α=.05). RESULTS: The results showed significant changes in color after artificial aging in all the groups (P<.05). Independent of the material studied, red wine resulted in the highest level of discoloration. Intermediate values were found for orange juice, UV accelerated aging, and the cola soft drink. The lowest values of ΔE were found for specimens stored in distilled water. CONCLUSIONS: All composite resins showed some color alteration after the aging methods. The surface sealant did not alter the color stability of the tested materials.

Radical polymerization inside living cells.

Polymerization reactions conducted inside cells must be compatible with the complex intracellular environment, which contains numerous molecules and functional groups that could potentially prevent or quench polymerization reactions. Here we report a strategy for directly synthesizing unnatural polymers in cells through free radical photopolymerization using a number of biocompatible acrylic and methacrylic monomers. This offers a platform to manipulate, track and control cellular behaviour by the in cellulo generation of macromolecules that have the ability to alter cellular motility, label cells by the generation of fluorescent polymers for long-term tracking studies, as well as generate a variety of nanostructures within cells. It is remarkable that free radical polymerization chemistry can take place within such complex cellular environments. This demonstration opens up a multitude of new possibilities for how chemists can modulate cellular function and behaviour and for understanding cellular behaviour in response to the generation of free radicals.

Direct UV-replica molding of biomimetic hierarchical structure for selective wetting.

describe a one-step UV-replica molding method for fabricating a biomimetic dual-scale hierarchical structure. The use of UV-curable, acrylate-functionalized perfluoropolyethers allows for a high fidelity replication of a low-energy surface with multiscale texture, thereby directly creating a superhydrophobic surface without any complicated processing. The superhydrophobic surface can simply be transformed selectively into a superhydrophilic surface by exposure to deep ultraviolet light. The prepared surface is inert to chemicals and solvents and maintains its wettability over a long period of time.

Free radical scavenging potential of L-proline: evidence from in vitro assays.

An assessment of the potential of proline to scavenge free radicals was made in a couple of in vitro assay systems, namely graft co-polymerization and autooxidation of pyrogallol. Both these assays are essentially dependent upon free radical mechanisms. Graft co-polymerization involved a ceric (Ce(4+)) ion- or gamma-radiation-induced grafting of methyl acrylate (MA) onto a cellulose backbone. The degree of grafting, measured gravimetrically, was taken as a measure of free radical generation. The gamma-radiation-dependent grafting was far greater than that due to Ce(4+) ions. Inclusion of proline in the assay, irrespective of the initiator used, led to suppression of grafting in a concentration-dependent manner indicating the ability of proline to scavenge free radicals. The gamma-radiation-dependent grafting was also suppressed by hydroquinone and glutathione but not by ascorbate, glycine and spermine. In contrast to graft co-polymerization, proline did not inhibit the autooxidation of pyrogallol, a reaction involving superoxide radical generation. A subset of data constitutes an evidence for the ability of proline to scavenge free radicals in vitro. It is implied by extension that free proline, known to accumulate in plant tissues during abiotic stresses, would contribute to scavenging of surplus free radicals produced under a variety of abiotic stresses.

Can CQ be completely replaced by alternative initiators in dental adhesives?

Despite good clinical acceptance, photoinitiating systems based on camphorquinone and amines raise concerns in terms of yellowing, aging, toxicity, or degradation in low pH conditions. This study aimed to prove whether CQ could be successfully replaced by alternative initiators in adhesive systems. Further, the efficiency of a prototype dual-wavelength LED (= Light Emitting Diode) curing unit was analyzed. In two commercial adhesive systems, CQ was completely replaced by Lucirin TPO. The commercial adhesives and their experimental counterparts were evaluated after curing for 10 seconds and 20 seconds with two dual-wavelength LED units and one regular LED unit, by applying the curing unit on the adhesive surface at two distances of 0 mm and 5 mm. Degree of cure and mechanical properties (Vickers hardness and modulus of elasticity) were assessed after 24-hour storage in distilled water at 37 degrees C. Experimental data showed that the CQ-amine system could be completely replaced by Lucirin TPO when dual-wavelength LED unit was used for photoactivation.

New matrix polymers for photo-activated resin composites using di-alpha-fluoroacrylic acid derivatives.

A novel matrix resin for photo-activated resin composites was developed using alpha-fluoroacrylic acid derivatives. To render resin composites with improved mechanical properties, silica fillers were also used. It was found that the newly developed fluorine-substituted monomer was polymerized quite easily not only by free radical chemical initiators, but also by photoirradiation using free radical photoinitiator system. In particular, the photopolymerization rate of the novel monomer was more than two times faster than that of corresponding methacrylate-based monomer. Composite based on the newly developed matrix resin had higher micro-Vickers hardness and compressive strength values than the methacrylate-based composite, and that it contained only trace residual monomers compared with the methacrylate-based material. The high polymerization conversion of the fluorine-substituted monomer could be attributed to the polar effect or the small steric hindrance of fluorine at the alpha-position.

Transducer impulse response correction for a deconvolution derived ultrasound transit time spectrum.

Propagation of ultrasound through a complex composite sample may exhibit phase interference between two or more sonic-rays if differences in transit time are less than the pulse length. The transit time spectrum of a test sample, equivalent to its impulse response, was derived through active-set deconvolution of ultrasound signals with, and without, the test sample. The aim of this study was to test the hypothesis that in cases where only the transmit ultrasound transducer's digitally-coded excitation signal is available, hence not the input ultrasound signal without the test sample, incorporation of the transducer impulse response may increase both accuracy and precision of ultrasound transit time spectroscopy. A digital 1 MHz sinusoid signal was used to create an ultrasound pulse that was propagated through a 5 step-wedge acrylic sample immersed in water. Transit time spectra were obtained through deconvolution utilising an ultrasound input signal, along with a digital input signal, with and without incorporation of the transducer impulse response. Incorporation of the transducer impulse response reduced a quantitative measure of noise-to-signal ratio by a factor of 12. The paper has demonstrated the potential for increased accuracy and precision of transit time spectroscopy when the transducer impulse response is incorporated within active-set deconvolution analysis.

Comparative behavior between sunscreens based on free or encapsulated UV filters in term of skin penetration, retention and photo-stability.

BACKGROUND: The growing incidence of photodamaging effects caused by UV radiation (e.g. sunburn, skin cancer) has increased the attention from health authorities which recommend the topical application of sunscreens to prevent these skin damages. The economic stakes for those companies involved in this international market are to develop new UV filters and innovative technologies to provide the most efficient, flexible and robust sunscreen products. Today the development of innovative and competitive sunscreen products is a complex formulation challenge. Indeed, the current sunscreens must protect against skin damages, while also being safe for the skin and being sensory and visually pleasant for the customers when applied on the skin. Organic UV filters, while proposing great advantages, also present the risk to penetrate the stratum corneum and diffuse into underlying structures with unknown consequences; moreover, their photo-stability are noted thorny outcomes in sunscreen development and subsequent performance. In recent years, the evaluation of the interaction between skin and sunscreen in terms of penetration after topical application has been considered from European authority but still its testing as their photo-stability assessment are not mandatory in most countries. OBJECTIVE: This study, based on in-vitro approaches, was performed to evaluate and compare the retention and the penetration of organic UV filters in free or encapsulated form inside the skin as well as their respective photo-stability. METHODS: Sunscreen formulation with a combination of Avobenzone and Octocrylene in "free form" and a formulation using the same UV filters but encapsulated in a sol-gel silica capsule, were analyzed and compared by FTIR Imaging Spectroscopy. Tape stripping method was used to investigate the penetration of these UV filters inside the stratum corneum. Their photo-stabilities were evaluated by spectroscopic measurements (FTIR, UV/Vis) and standard measurements were calculated: AUC (Area Under the Curve) and SPF (Sun Protection Factor). RESULT: With traditional formulation, the organic UV filters penetrated significantly into the stratum corneum while the same UV filters combined with encapsulation technology remained on the skin surface. The encapsulation technology also improved significantly their stability. CONCLUSION: Encapsulation technology is a promising strategy to improve the efficacy of sunscreen product using organic UV filters and to reduce safety problem. On the other hand, this study highlighted the pertinence of the FTIR Spectroscopy to test, compare and investigate sunscreen formulations.

Characterisation of UV-cured acrylate networks by means of hydrolysis followed by aqueous size-exclusion combined with reversed-phase chromatography.

UV-cured networks prepared from mixtures of di-functional (polyethylene-glycol di-acrylate) and mono-functional (2-ethylhexyl acrylate) acrylates were analysed after hydrolysis, by aqueous size-exclusion chromatography coupled to on-line reversed-phase liquid-chromatography. The mean network density and the fraction of dangling chain ends of these networks were varied by changing the concentration of mono-functional acrylate. The amount and the molar-mass distribution of the polyethylene-glycol chains between cross-links (M(XL)) and polyacrylic acid (PAA) backbone chains (the so-called kinetic chain length (kcl)) in the different acrylate networks were determined quantitatively. The molar-mass distribution of kcl revealed an almost linear dependence on the concentration of mono-functional acrylate. Analysis of the starting materials showed a significant concentration of mono-functional polyethylene-glycol acrylate. In combination with the analysis of the extractables of the UV-cured networks (polymers not attached to the network, impurities that originate from the photo-initiator and unreacted monomers), more insight in the total network structure was obtained. It was shown that the UV-cured networks contain only small fractions of residual compounds. With these results, the chemical network structure for the different UV-cured acrylate polymers was expressed in network parameters such as the number of PAA units which are cross-linked, the degree of cross-linking, and the network density, which is the molar concentration of effective network chains between cross-links per volume of the polymers. The mean molar mass of chains between chemical network junctions (M(C)) was calculated and compared with results obtained from solid-state NMR and DMA. The mean molar mass of chains between network junctions as determined by these methods was similar.

In situ synthesis of monolithic stationary phases for electrochromatographic separations: study of polymerization conditions.

Acrylate-based monolithic capillary columns were prepared from fused-silica capillaries using UV photopolymerization. The effect of the pretreatment of the capillary wall surface before polymerization was investigated and several procedures were compared. The columns were characterization by van Deemter curves and SEM imaging. The results indicated that a pre-silanization of the capillary wall in order to introduce methacrylate groups at the wall surface gave similar efficiencies but more homogeneous structures than when the silanization agent was introduced in the polymerization mixture. The conditioning of the capillary before silanization, especially the conditions of basic rinsing was also an important factor. The effect of the dose of UV light that was applied for the polymerization had also been investigated. The results demonstrated that the irradiation energy is a critical parameter. The minimum energy threshold required to obtain a suitable monolith was 3 J/cm(2) and the maximum was around 12 J/cm(2). A higher energy destroys the monolith. Within the convenient range of energy, the columns had the same efficiency and a good structure as seen by SEM imaging. Using the optimized procedure for the pretreatment and an adequate energy, the column-to-column repeatability was found good (n = 12). The repeatability was obtained for the plate height at two velocity values, the retention factor and the electroosmotic mobility with RSD values below 10.

A new copolymer membrane controlling clonidine linear release in a transdermal drug delivery system.

A new type of copolymer membranes was prepared through photosynthesis of mixtures of three different monomers. The membranes present a linear permeation property in clonidine transdermal drug delivery system. Monomers used in the photosynthesis were 2-hydroxy-3-phenoxypropylacrylate, 4-hydroxybutyl acrylate and sec-butyl tiglate. Permeation property of the membranes with different monomer ratios and thickness were investigated. When clonidine concentrations were in 3.0 - 5.0 mg/ml range, membranes showed near zero order permeation rates. An optimized membrane was characterized by FTIR, DSC and SEM.

pH-responsive amphiphilic hydrogel networks with IPN structure: a strategy for controlled drug release.

A pH-responsive amphiphilic hydrogel with interpenetrating polymer networks (IPN) structure for controlled drug release was proposed. The IPN was constructed with hydrophilic poly(acrylic acid) (PAA) and hydrophobic poly(butyl acrylate) (PBA). Using drug N-acetyl-5-methoxytryptamine (melatonin, MEL) as a model molecule, the controlled drug release behaviors of the IPN were investigated. It is found that not only the release of MEL from the IPN can respond to change in pH, but also the presence of hydrophobic network can overcome disadvantageous burst effect of hydrophilic network. This may be a result of hydrophobic aggregation encapsulating MEL molecules.

Evaluation of the photostability of different UV filter combinations in a sunscreen.

Development of photostable sunscreens is extremely important to preserve the UV protective capacity and to prevent the reactive intermediates of photounstable filter substances behaving as photo-oxidants when coming into direct contact with the skin. Thus, the objective of this study was to evaluate the photostability of four different UV filter combinations in a sunscreen by using HPLC analysis and spectrophotometry. The formulations that were investigated included four different UV filter combinations often used in SPF 15 sunscreens. The UV filter combinations were: octyl methoxycinnamate (OMC), benzophenone-3 (BP-3) and octyl salicylate (OS) (formulation 1); OMC, avobenzone (AVB) and 4-methylbenzilidene camphor (MBC) (formulation 2); OMC, BP-3 and octocrylene (OC) (formulation 3); OMC, AVB and OC (formulation 4). In the photostability studies, 40 mg of each formulation were spread onto a glass plate and left to dry before exposure to different UVA/UVB irradiation. Exposed samples were then immersed in isopropanol and the dried film dissolved ultrasonically. The filter components in the resulting solution were quantified by HPLC analysis with detection at 325 nm and by spectrophotometry. In this study, the four UV filter combinations showed different photostability profiles and the best one was formulation 3 (OMC, BP-3 and OC), followed by formulations 4, 1 and 2. In addition, OC improved the photostability of OMC, AVB and BP-3.

Large area UV casting using diverse polyacrylates of microchannels separated by high aspect ratio microwalls.

Large area molding of long and deep microchannels separated by high aspect ratio microwalls is important for high sensitivity and high throughput microfluidic devices. Ultraviolet (UV) casting is a feasible, economical and convenient method of replication of such microstructures in plastics. It is shown that a wide variety of polyacrylates with diverse properties such as those made from epoxy (EP), polyurethane (UR), polyester (ES), poly (ethylene glycol) (EG) and poly(propylene glycol) (PG) can be used for the high aspect ratio (7-9) UV casting of such linear microstructures over a 100 mm diameter, enlarging the range of applications of the replicated microstructures. Some challenges arise. With the EG formulation, wavy microstructures were observed; this can be overcome by stress relaxation. With non-polar PG formulation, poor adhesion between the polyester substrate and resin can lead to delamination of the casting from the substrate during demolding; this can be overcome by pre-coating a partially cured same resin on the polyester substrate. An optimum UV irradiation time was important for cure at the deepest end of the microstructure without excessive crosslinking leading to much increased demolding forces. The viscosity and wetting capability of the formulations were found to affect replication fidelity.