Influence of screw configuration on reduction and stabilization of simulated complete lateral condylar fracture in equine limbs.

OBJECTIVE: To determine the influence of screw configuration on the reduction and stabilization of simulated complete lateral condylar fracture. STUDY DESIGN: Randomized experimental crossover study. METHODS: A lateral condylar fracture was simulated in 18 cadaver limbs from nine horses. Each limb underwent repair with 4.5 mm diameter cortex screws, tightened to 4 Nm, in a linear and triangular configuration. Computed tomography (CT) of each repair was performed with the limbs in unloaded and loaded conditions. Fracture gaps were measured at the dorsal, palmar, and middle locations of the third metacarpal condyle. Fracture gap measurements were graded 0-4, based on voxels. Following descriptive analysis, a Bayesian network (BN) model was fitted to the data. RESULTS: The median fracture grade was 0 (range: 0-4) for unloaded linear repairs and 2 (0-4) for loaded linear repairs. The median fracture grade was 0 (0-3) for unloaded triangular repairs and 1 (0-3) for loaded triangular repairs. Bayesian network sensitivity analysis showed that the construct configuration reduced the uncertainty in the measured fracture outcome by 0.8%. CONCLUSION: Triangular screw configuration resulted in better fracture reduction and stability in comparison with linear screw configuration. However, the BN sensitivity analysis results showed that the effect of construct configuration on fracture outcome was weak. CLINICAL SIGNIFICANCE: These findings indicate a low probability that triangular repair of lateral condylar fracture will result in improved outcomes, when compared with linear repair.

Arthroscopically guided lag screw fixation of subchondral bone cysts in the medial femoral condyle in Thoroughbred racehorses: description of technique and comparative results.

OBJECTIVE: To describe an arthroscopically guided technique for lag screw placement across subchondral bone cyst (SBC) in the medial femoral condyle (MFC) and to compare postoperative racing performance with corticosteroid injection and cyst debridement. STUDY DESIGN: Retrospective cohort study. ANIMALS: One hundred twenty-three horses with 134 MFC SBCs undergoing treatment at a single referral hospital in the UK between January, 2009, and December, 2020. METHODS: Sex, age, limb affected, radiographic cyst dimensions, preoperative and postoperative lameness, surgical technique (lag screw placement, cyst debridement, intralesional corticosteroid injection), and, where applicable, screw positioning were recorded retrospectively. A ratio was calculated using measurements from preoperative and postoperative radiographs. Outcome was assessed by resolution or improvement in lameness, reduction in cyst size, and starting one race after treatment. Outcome data was compared between treatment groups. RESULTS: Twenty-six of 45 (57.8%) horses that underwent transcondylar screw placement raced postoperatively, at a median of 403 days between surgery and first postoperative race. There was no difference between treatment groups with regard to racing or preoperative and postoperative lameness. Cysts treated with transcondylar screw placement had a greater reduction in cyst size and a reduced period of convalescence in comparison with those that underwent debridement; the results were similar to those treated by intralesional corticosteroid injection. CONCLUSION: Postoperative racing rates were similar for all techniques. Convalescence was reduced for lag screw placement and corticosteroid injection compared to debridement. CLINICAL SIGNIFICANCE: The arthroscopically guided technique results in radiographically consistent screw placement and cyst engagement and offers a viable alternative to other treatments.

Medial versus lateral transcondylar screw placement for canine humeral intracondylar fissures: A randomized clinical trial.

OBJECTIVE: To determine the influence of screw direction on complications following transcondylar screw placement for the treatment of canine humeral intracondylar fissures (HIFs). STUDY DESIGN: Equivalence, parallel group, randomized clinical trial. SAMPLE POPULATION: Fifty-two client owned dogs (73 elbows). METHODS: Transcondylar screw placement was randomized to either a medial or lateral approach. The primary outcome was the incidence of postoperative complications. RESULTS: There were 37 cases in the lateral approach group and 36 cases in the medial approach group. There was a significantly greater proportion of postoperative complications following placement of transcondylar screws from a lateral to medial direction (p = .001). There were seven cases with complications (19%) in the medial approach group versus 23 cases with complications (62%) in the lateral approach group. The majority of complications were seromas (n = 13) and surgical site infections (n = 16) with 4 complications requiring further surgery. Implant area moment of inertia (AMI), normalized to bodyweight, was lower in dogs with a major complication (p = .037). CONCLUSION: Transcondylar screws placed from lateral to medial for canine HIFs had a greater proportion of postoperative complications in this randomized clinical trial design. Implants with a lower AMI, relative to bodyweight, were more likely to lead to major complications. CLINICAL SIGNIFICANCE: We recommend placing transcondylar screws from medial to lateral for canine HIFs to reduce the risk of postoperative complications. Relatively small diameter implants had an increased risk of major complications.

Tibial fracture associated with use of Arthrex self-tapping screws during tibial plateau leveling osteotomy in dogs and development of transcortical tibial fracture.

OBJECTIVE: Medical records for dogs treated with tibial plateau leveling osteotomy (TPLO) using Arthrex 3.5 mm self-tapping screws (STS) were evaluated to determine the incidence rate of transcortical tibial fractures (TCTF) and development of complications. STUDY DESIGN: Retrospective case report. STUDY POPULATION: A total of 78 dogs. METHODS: Dogs that underwent a TPLO performed from March 2022 to August 2023 were reviewed. Postoperative TPLO radiographs were examined for evidence of a TCTF with Arthrex 3.5 mm STS. Records were reviewed for complications up to 14 weeks after surgery. RESULTS: Evidence of a TCTF was found in 42% of cases (33 of 78) and 14% (36 of 250) of STS screws distal to the osteotomy. TCTFs were only identified distal to the osteotomy. Three dogs had radiographic evidence of more than one TCTF. Of the dogs with radiographic TCTF, 6% of patients (2 of 33) developed a major complication that required surgical stabilization of a tibial fracture associated with screw angulation relative to the plate. CONCLUSION: Use of Arthrex 3.5 mm STS for TPLO is associated with risk of TCTF. TCTF can compromise the structural properties of the tibia and cause complete tibial fracture requiring major revision surgery. CLINICAL SIGNIFICANCE: Development of TCTF after use of STS for TPLO has been recognized, in contrast to use of non-self-tapping screws, and was considered a benign complication. Our findings suggest TCTF associated with Arthrex 3.5 mm STS use in TPLO can contribute to major complications after surgery, including complete tibial fracture, particularly if screws are not placed perpendicular to the plate.

A novel transcoronal surgical technique for the treatment of cystic lesions of the distal phalanx: A cadaveric study.

OBJECTIVE: To assess the feasibility of a novel transcoronal approach for the treatment of axial type 3 cysts of the palmar/plantar aspect of the distal phalanx (P3). STUDY DESIGN: Ex vivo, experimental study. SAMPLE POPULATION: Ten cadaveric specimens, four forelimbs and six hindlimbs. METHODS: All cadaveric specimens underwent radiographically guided drilling, followed by cortical screw placement. The cartilage was macroscopically assessed after disarticulation of the distal interphalangeal joint. The entry point and trajectory were evaluated with computed tomography. Results were categorized as: axial, near-axial and abaxial. The minimal distance from the outer margin of the drill hole and the proximal border of the subchondral bone plate was measured using frontal computed tomographic slices. RESULTS: Eight of the 10 screws were in an axial to near-axial position and nine followed the desired axial to near-axial trajectory. One screw was inserted axially but continued in an abaxial trajectory. Iatrogenic damage to the joint cartilage, flexor cortex and solar canal of P3 was not observed. All cortical screws were placed close to the proximal subchondral bone-plate of P3. CONCLUSION: The desired axial/near-axial drilling and screw placement, under radiographic guidance, was achieved in nine out of 10 specimens. CLINICAL SIGNIFICANCE: This novel technique seems promising for the treatment of inaccessible P3 cysts. Additional studies are required to investigate its feasibility in clinical cases, and the long-term outcome following transcystic screw placement of type 3 P3 cysts.

Prospective evaluation of the surgical stabilization and outcome of canine tibial plateau fractures in three cases.

OBJECTIVE: To report the surgical approaches and stabilization of lateral and medial tibial plateau fractures (TPF), as well as the long-term outcome following repair. STUDY DESIGN: Prospective series of three client-owned dogs. ANIMALS: Three dogs. METHODS: For the two lateral TPF cases (Unger type 41-B1), the surgical approach included separation of the lateral collateral ligament and long digital extensor tendon. The lateral meniscus was elevated to allow visualization of the tibial surface and assess fracture reduction. The first case was repaired using two 2.0 mm lag screws (with washers). The second case sustained a lateral TPF, fibular fracture and concurrent tubercle of Gerdy fracture. Both tibial fractures were stabilized using two 2.0 mm lag screws with washers and two 0.9 mm Kirschner wires (K-wires). A third case, diagnosed with an Unger type 41-B2 medial TPF, was treated using 0.9 mm K-wires and 22-gauge tension band. RESULTS: There were no major complications noted. One minor complication occurred (screw yield two weeks postoperatively). By 8 weeks, all patients reached clinical union with good limb function. Owners were contacted 9-36 months postoperatively. LOAD scores and examinations were performed for two of three patients; the third patient was not contactable after relocating out of state. Both cases with completed questionnaires had a LOAD score of 5/52. CONCLUSION: Tibial plateau fractures are rare in canine patients. While challenging, they can be successfully managed using a combination of lag screws, K-wires, and tension band. CLINICAL SIGNIFICANCE: Surgical stabilization of TPF is feasible and may reduce the risk of meniscal injury.

Fluoroscopically-assisted closed reduction and percutaneous fixation of sacroiliac luxations in cats using 2.4 mm headless cannulated compression screws: Description, evaluation and clinical outcome.

OBJECTIVE: To describe fluoroscopically-assisted closed reduction and percutaneous fixation of sacroiliac-luxation (SIL) in cats and report radiographic results and long-term functional outcomes. STUDY DESIGN: Retrospective clinical study. ANIMALS: Eleven cats. METHODS: Percutaneous fixation of 17 SILs in 11 cats was performed with 2.4 mm headless cannulated compression screws under fluoroscopic guidance. Luxation-reduction, screw placement and purchase within the sacral body, pelvic canal diameter ratio (PCDR) and hemipelvic canal width ratio (HCWR) were assessed on pre- and postoperative radiographs. Radiographic follow-up was performed to assess the same parameters when available. Long-term clinical outcome was evaluated with an owner questionnaire. Wilcoxon paired-test was performed for comparison. RESULTS: Mean age and bodyweight of the cats were 3.3 ± 2.6 years and 4.0 ± 0.82 kg, respectively. Nine cats presented with concurrent pelvic injuries. Median luxation-reduction was 94.1% (IQR = 13.9) and median screw-purchase within the sacral body was 73.3% (IQR = 17.0) immediately postoperatively. One screw exited the sacral body caudally. Upon 7-week radiographic follow-up, luxation-reduction (88.3%, IQR = 20.1) and screw-purchase (70.7%, IQR = 12.8) had decreased compared to immediately postoperatively (p = .008 and p = .013 respectively). Screw migration was not observed. PCDR and HCWR measured on postoperative radiographs indicated successful restoration of the pelvic canal width. Owners reported an excellent long-term functional outcome (mean postoperative time: 19 ± 5 months). CONCLUSION: Fluoroscopically-assisted closed reduction and fixation of feline SIL using 2.4 mm headless cannulated compression screws allowed good reduction and optimal screw purchase within the sacral body. An excellent functional outcome was reported. CLINICAL SIGNIFICANCE: Minimally invasive reduction and fixation with headless compression screws should be considered in cats with SIL.

Biomechanical comparison of titanium alloy additively manufactured and conventionally manufactured plate-screw constructs.

AIM: To biomechanically compare the bending stiffness, strength, and cyclic fatigue of titanium additively manufactured (AM) and conventionally manufactured (CM) limited contact plates (LCP) of equivalent dimensions using plate-screw constructs. METHODS: Twenty-four 1.5/2.0-mm plate constructs (CM: n = 12; AM: n = 12) were placed under 4-point bending conditions. Data were collected during quasi-static single cycle to failure and cyclic fatigue testing until implants plastically deformed or failed. Bending stiffness, bending structural stiffness, and bending strength were determined from load-displacement curves. Fatigue life was determined as number of cycles to failure. Median test variables for each method were compared using the Wilcoxon rank sum test within each group. Fatigue data was also analysed by the Kaplan-Meier estimator of survival function. RESULTS: There was no evidence for a difference in bending stiffness and bending structural stiffness between AM and CM constructs. However, AM constructs exhibited greater bending strength (median 3.07 (min 3.0, max 3.4) Nm) under quasi-static 4-point bending than the CM constructs (median 2.57 (min 2.5, max 2.6) Nm, p = 0.006). Number of cycles to failure under dynamic 4-point bending was higher for the CM constructs (median 164,272 (min 73,557, max 250,000) cycles) than the AM constructs (median 18,704 (min 14,427, max 33,228) cycles; p = 0.02). Survival analysis showed that 50% of AM plates failed by 18,842 cycles, while 50% CM plates failed by 78,543 cycles. CONCLUSION AND CLINICAL RELEVANCE: Additively manufactured titanium implants, printed to replicate a conventional titanium orthopaedic plate, were more prone to failure in a shorter fatigue period despite being stronger in single cycle to failure. Patient-specific implants made using this process may be brittle and therefore not comparable to CM orthopaedic implants. Careful selection of their use on a case/patient-specific basis is recommended.

Proximal femoral deformity correction and total hip arthroplasty in a dog using 3D printed custom guides.

OBJECTIVE: To report the successful correction of a proximal femoral deformity (PFD) and total hip arthroplasty (THA) in a dog with the use of three-dimensionally (3D) printed custom surgical guides (CSGs). STUDY DESIGN: Case report. ANIMALS: One-year-old, male neutered, Goldendoodle. METHODS: Uniapical proximal varus and recurvatum femoral deformity (PFD) precluded femoral stem placement for THA, which was indicated for severe hip dysplasia. Using CT-derived bone and implant models, custom ostectomy and reduction guides for deformity correction were designed. A 13-hole 3.5 mm locking compression plate was contoured and applied to 3D printed models of the corrected femur and screw trajectory holes were incorporated into the CSGs. RESULTS: A caudolateral closing wedge ostectomy of the proximal femur was achieved with the aid of the CSGs and precontoured plate to within 2° of varus and 1° of recurvatum of the virtual surgical plan. Placement of a press-fit femoral stem was achieved with 7° of varus and 9° of caudal angulation. The plate was secured using six locking screws, two cortical screws, and two 18-gauge double-loop cerclage wires. No lameness and normal range of motion of the hip were observed on clinical examination 3 months after surgery. Radiographs at 3 and 6 months revealed static implant positioning, and complete bony union at the ostectomy site. CONCLUSION: Virtual surgical planning and CSGs led to successful concurrent THA and femoral deformity correction.

The effect of an aiming device on the accuracy of humeral transcondylar screw placement.

OBJECTIVES: (1) To evaluate the accuracy of an aiming device on placement of humeral transcondylar screws compared to fluoroscopic methods. (2) To compare experience level on outcome. STUDY DESIGN: Randomized, match pair, prospective ex-vivo study. SAMPLE POPULATION: A total of 68 dogs. METHODS: Canine cadaveric forelimbs were randomly assigned to either aiming device or fluoroscopic-guided groups, and to diplomate or resident. Digital radiography was used to evaluate screw trajectory deviation and eccentricity on the humeral condyle. Procedure time, outcome based on experience, and complications were recorded. RESULTS: The aiming device screw trajectory angle was decreased in the right limb (1.9 ± 1.1°) compared with the left (3.6 ± 1.1°, p = .0178), and compared to fluoroscopy (3.4 ± 1.1° p = .0128). There was no difference between leg laterality with fluoroscopy (p = .9979). Trajectory angle was increased with resident versus diplomate (3.4 ± 1.1° and 2.5 ± 1.1° respectively, p = .0366). Eccentricity deviation was decreased using fluoroscopy versus aiming device (3.1 ± 0.36 mm, 4.2 ± 0.36 mm, respectively, p = .0017). The risk of joint involvement was 8 times greater in aiming device groups, though not significant (p = .0575). Significant complications included increased drill attempts in fluoroscopic groups (p = .0237). CONCLUSION: The aiming device provided accurate placement of transcondylar screws, in terms of both position on the condyle and trajectory angle. Results were similar to fluoroscopic-guided method. CLINICAL SIGNIFICANCE: An aiming device is an acceptable means of placing humeral transcondylar screws. The use of the aiming device had an eight times increased risk of joint involvement compared to fluoroscopy.

Biomechanical comparison of compact versus standard flute drill bits, and interlocking versus buttress thread self-tapping cortical bone screws in cadaveric equine third metacarpal condyle.

OBJECTIVES: To compare (1) performance of compact versus standard flute drill bits, (2) screw insertion properties and (3) pullout variables between interlocking thread (ITS) and buttress thread (BTS) self-tapping screws in third metacarpi. STUDY DESIGN: In vitro experimental study. SAMPLE POPULATION: Paired third metacarpi from 11 Thoroughbreds aged 2-4 years. METHODS: Screws were inserted into the lateral condylar fossae following bone preparation using the respective drill bit for each screw type. Screw pullout was achieved using a mechanical testing system. Density and porosity of bone surrounding screw holes was measured with microcomputed tomography following each pullout test. Drilling, screw insertion and pullout variables were compared between drill bit and screw types using repeated measures ANOVA. Linear regression analyses were used to characterize relationships between bone tissue properties and drill bit and screw outcomes. RESULTS: Maximum torque power spectral density (PSD) was lower for compact flute drill bits. Insertion torque was 50% higher for ITS. BTS had 33% greater preyield stiffness and 7% greater mean yield force. Bone tissue properties affected measured variables similarly for both screw and drill bit types. CONCLUSIONS: Lower torque PSD may increase durability of the compact flute drill bit. ITS had greater insertional torque, which may reflect greater bone engagement. BTS had greater resistance to axial pullout forces. CLINICAL SIGNIFICANCE: Metacarpal bone provides a simple model for comparison of drill bit and screw designs. Use of ITS to repair equine fractures subject to predominantly tensile forces is not justified based on the results of this study.

Outcomes for 15 cats with bilateral sacroiliac luxation treated with transiliosacral toggle suture repair.

OBJECTIVE: To report a surgical technique and outcomes of transiliosacral toggle suture repair to treat feline bilateral sacroiliac luxation/fracture (SILF). STUDY DESIGN: Retrospective study. ANIMALS: Fifteen client-owned cats. METHODS: The medical records of cats with bilateral SILF treated using a transiliosacral toggle suture repair were reviewed. Short- and medium-term outcomes were assessed through standard postoperative clinical evaluation and radiographs, including measurements of angle of deviation (AoD), percentage of reduction (PoR), and pelvic canal width ratio (PCWR). Long-term functional follow up was obtained from a questionnaire derived from the Feline Musculoskeletal Pain Index (FMPI). RESULTS: Fifteen cats were enrolled retrospectively, among which 13 survived to discharge. One minor wound complication, treated by secondary intention healing, was encountered. No major complication was reported. Immediately postoperatively, the mean absolute PoR values were 88.1 ± 11.2% and 91 ± 11.6% on the right and left side, respectively. The mean absolute AoD was 3.1 ± 2.8°, and the mean PCWR was 1.24 ± 0.08. The medium-term radiographic follow up at a median of 205 (71-682) days postsurgery revealed the good stability of the repair. Excellent functional outcomes were identified upon the analysis of 12 long-term questionnaires at a median of 365 (119-798) days postsurgery. CONCLUSION: Anatomic reduction was satisfactory and comparable with previously described techniques with good implant placement documented. Functional outcomes based on FMPI-derived questionnaires were good to excellent in our population. CLINICAL SIGNIFICANCE: Transiliosacral toggle suture stabilization of bilateral SILF was associated with good outcomes in cats. Further studies are required to compare biomechanical properties and outcomes between this technique and previously described transiliosacral stabilization.

Surgical management of a Salter-Harris type I proximal physeal fracture of the tibia in a foal: a case report.

BACKGROUND: One of the traumatic fractures occurring in the hindlimb of the foals is physeal fractures of the tibia. The most common type of proximal tibial fracture in foals is reported to be Salter-Harris type II. CASE PRESENTATION: This case report describes the history, clinical signs, radiographic findings, and surgical management of a proximal physeal fracture of the tibia due to the kick trauma in a 2-weeks-old Kurdish female foal, with signs of left pelvic limb lameness, valgus deviation with non-weight-bearing, non-mobility in stifle region and crepitation in the affected area. In this case, radiography was utilized to confirm the fracture and detect the exact location of the fracture fragments. The Salter-Harris type I accompanied by tibial tuberosity fracture was diagnosed. In this case, a size 4.5 mm seven-hole, T-plate, and cortical bone screws were employed to fix the physeal fracture, and a cortical bone screw was utilized to fix the tibial tuberosity in the normal position. Case follow-up during two months showed no significant complications, and the patient was fully recovered (no lameness anymore). CONCLUSIONS: To our knowledge, this is the first report of Salter-Harris type I fracture in proximal tibia accompanied by tibial tuberosity fracture in a foal treated by a T-plate implant. A cortical screw in lag fashion for tibial tuberosity was utilized in this case for the first time, and the results were satisfying. T-Plate fixation can be recommended as an effective surgical treatment for proximal tibial fractures in foals.

Ex vivo biomechanical comparison of four Center of Rotation Angulation Based Leveling Osteotomy fixation methods.

OBJECTIVE: To compare the strength of four constructs used to secure an osteotomy in a Center of Rotation Angulation (CORA)-Based Leveling Osteotomy (CBLO) in an ex vivo model. STUDY DESIGN: Ex vivo study. SAMPLE POPULATION: Thirty-two canine tibiae from 17 skeletally mature cadavers weighing between 18 and 33.2 kg. METHODS: Thirty-two paired tibiae with patella and patellar tendon were collected. Each tibia was randomly allocated to a construct group: plate and pin (Plate), plate with countersink compression screw (HCS), plate with tension band (TB), or plate with HCS and TB (HCSTB). Samples were loaded by distraction until failure. The stiffness, yield load, and ultimate load were compared between each fixation method. RESULTS: No difference in stiffness of the constructs was detected between groups (p = .6937). Yield load for the HCSTB group (1211.06 N) was greater than the TB group (1016.41 N), the HCS group (907.20 N), and the Plate group (787.73 N) (p = .0069). The ultimate load for the HCSTB group (1387.82 N) was greater than the TB group (1076.36 N), HCS group (926.62 N), and the Plate group (774.35 N) (p = .0004). CONCLUSIONS: CBLO fixation augmented with a TB and HCS provided a stronger construct that withstood a greater yield load and ultimate load than either augmentation strategy alone. CLINICAL SIGNIFICANCE: Augmenting a CBLO fixation with a TB and a HCS can provide increased construct strength.

Compression generated by cortical screws in an artificial bone model of an equine medial femoral condylar cyst.

OBJECTIVE: Determine compression generated by lag and neutral screws over 12 h using two bone analogs. STUDY DESIGN: Experimental study. SAMPLE POPULATION: Bone analogs were made of composite synthetic bone (CSB) or three-dimensional printed polylactic acid (PLA). Analogs had a 2 mm exterior shell with a 10 mm thick internal layer of open-cell material. METHODS: Bone analogs were opposed, making a 4-sided box with open ends. A central channel contained the sensor and the screws passed through it to engage both paired analogs. Four screw/analog conditions were tested: neutral and lag screw with bicortical engagement, neutral and lag screw with unicortical engagement. All screws were tightened to 2 Nm torque and compression values recorded at 0, 0.5, 1, 2, 6, and 12 h (six trials per condition). Medians were compared across groups for statistical significance. RESULTS: There was no difference in median compression between lag and neutral bicortical screws. For PLA, greater median compression was generated by neutral (median 437 N) and lag (median 379 N) bicortical screws compared to neutral unicortical screws (median 208 N, p < .001); lag bicortical screws generated greater median compression than lag unicortical screws (median 265 N, p = .012). For CSB, lag bicortical screws (median 293 N) generated greater median compression than neutral unicortical screws (median 228 N, p = .008). CONCLUSION: Lag and neutral screws generated similar compression. Bicortical screws had higher median compression than unicortical screws in bone analogs. CLINICAL SIGNIFICANCE: Neutral screws generate compression in cancellous bone analogs that can be increased with bicortical bone engagement.

Ex vivo comparison of lateral plate repairs of experimental oblique ilial fractures in cats.

OBJECTIVE: To determine the biomechanical behavior of different plate systems used for oblique ilial fracture fixation in cats. STUDY DESIGN: Ex vivo biomechanical study. SAMPLE POPULATION: Fifty fresh-frozen feline hemipelvises. METHODS: Standardized simple oblique ilial fractures were created and fixed via lateral plating, using different implant systems (10 fractures in each group) The systems were: (1) the Advanced Locking Plate System (ALPS-5); (2) the Advanced Locking Plate System (ALPS-6.5); (3) the Locking Compression Plate 2.0 (LCP); (4) the FIXIN 1.9-2.5 Series (FIXIN), and (5) the Dynamic Compression Plate 2.0 (DCP). Stepwise sinusoidal cyclic loading was applied until failure (10-mm displacement). The groups were compared with regard to construct stiffness and the number of cycles withstood before 1-, 2-, 5-, and 10-mm displacement. RESULTS: Bending stiffness was lower in ALPS-5 than in other specimens (P < .05). The ALPS-6.5 specimens withstood more cycles (P < .05) before 2-, 5-, and 10-mm displacement than the ALPS-5 and DCP specimens . The LCP and FIXIN specimens endured more cycles than DCP specimens before displaying 5- and 10-mm displacement (P < .05). The ALPS-6.5, FIXIN, and LCP specimens endured higher loads before failure than the DCP specimens (P < .05). Screw loosening occurred in all nonlocking specimens, and bone slicing occurred in all locking specimens. CONCLUSION: The DCP and ALPS-5 constructs are less resistant to cyclic loading. Failure in nonlocking specimens involved screw loosening. It involved bone slicing in locking specimens. CLINICAL SIGNIFICANCE: Both the plate size and the plate-screw interface are key to lateral plating success in cases of feline ilial fractures. The use of locking plates reduces the risk of the screw loosening in such cases.

The failure mode of a mechanically loaded equine medial femoral condyle analog with a void and the impact of lag and neutral screw placement.

OBJECTIVE: To determine the failure method of simulated equine medial femoral condyle (MFC) subchondral bone defects under compression and the influence of screw placement on failure resistance. STUDY DESIGN: In vitro study. SAMPLE POPULATION: Composite disks (CD) simulating the moduli of yearling bone in the MFC. METHODS: Four CD conditions were tested, all with a 12.7 mm void (n = 6 per condition): intact (no void), void only, void with a 4.5 mm screw placed in neutral fashion, and void with a 4.5 mm screw placed in lag fashion. Composite disks of each condition were tested under monotonic compression to 6000 N and cyclic compression to 10 000 cycles. Observable failure, load at first observable failure, and displacement at peak 2000 N load were compared among conditions. RESULTS: Specimens failed by cracking at the superior aspect of the void or the screw exit hole. After monotonic loading, cracks were observed 6/6 CD with a void, 6/6 CD with a void/lag screw, and 5/6 CD with a void/neutral screw. After cyclical testing, cracks were noted only on the superior aspect of 6/6 CD with a void and 3/6 CD with a void/lag screw. Displacement at peak load was 0.06 mm (intact), 0.32 mm (void), 0.24 mm (void/lag screw), and 0.11 mm (void/neutral screw). CONCLUSION: Model MFC voids failed by superior cracking that was resisted by lag and neutral screw placement. CLINICAL SIGNIFICANCE: Neutral screws may be an acceptable treatment for subchondral lucencies in the MFC.

Accuracy of a drilling with a custom 3D printed guide or free-hand technique in canine experimental sacroiliac luxations.

OBJECTIVE: To improve the accuracy of drilling during the repair of sacroiliac luxations (SILs) with a 3D-printed patient-specific drill guide (3D-GDT) compared to free-hand drilling technique (FHDT). STUDY DESIGN: Blinded, randomized, prospective ex vivo study. SAMPLE POPULATION: Sixteen canine cadavers (20-25 kg). METHODS: Dorsal, bilateral SILs were created. Pelvic CT was performed pre- and post-drilling. The FHDT was drilled followed by 3D-GDT. CT and 3D measurements of craniocaudal and dorsoventral angles were compared between FHDT and 3D-GDT, as well as deviations of entry and exit points relative to optimal trajectory. RESULTS: Mean craniocaudal and dorsoventral angles for both CT- and 3D-measured 3D-GDT (CT 4.2 ± 3.9° and 3.9 ± 3.2°, respectively; 3D 5.1 ± 5.1° and 2.8 ± 2.3°, respectively p = .0006) were lower compared to FHDT (CT 11.8 ± 4.0°, p < .0001 and 8.9 ± 6.1°, p = .01; 3D 12.4 ± 5.9°, p = .0006 and 5.3 ± 5.24°, p = .05). Entry dorsoventral and end craniocaudal, dorsoventral, and 3D linear deviations were reduced with 3D-GDT. Sacral corridor disruption was present in 20% (3/15) for FHDT compared with 0% for 3D-GDT. CT and 3D analyses were in strong agreement (r = 0.77). CONCLUSION: Deviations of drill trajectories were minimized relative to optimal trajectories with 3D-GDT compared to FHDT in the dorsoventral and craniocaudal planes. CLINICAL SIGNIFICANCE: The use of 3D-GDT improves accuracy of sacral drilling compared with FHDT in canine cadavers. These results justify further evaluation in a clinical, prospective study.

Mechanical evaluation of canine sacroiliac joint stabilization using two short screws.

OBJECTIVE: To assess the feasibility and mechanical stability of sacroiliac (SI) joint stabilization using 2 short 3.5 mm cortical screws, each spanning an average of 23% of the width of the sacral body. STUDY DESIGN: Cadaveric experimental study. SAMPLE POPULATION: Twenty-four canine pelvis specimens. METHODS: Pelvis specimens were prepared by disarticulation of the left SI joint and osteotomy of the left pubis and left ischium, and stabilized using a single long lag screw (LLS), 2 short lag screws (SLS) or 2 short positional screws (SPS). Computed tomography (CT) imaging was used to determine standardized screw lengths for each group and was repeated following implant insertion. Specimens were secured within a servohydraulic test frame and loaded through the acetabulum to simulate weight bearing under displacement control at 4 mm/min for 20 mm total displacement. Group mechanical testing data were compared. RESULTS: Peak load, yield load, and stiffness were more than 2 times greater in both the SLS and SPS groups when compared with the LLS group. No mechanical difference was identified between the short-screw groups. CONCLUSION: Sacroiliac luxation fixation using 2 short screws created a stronger, stiffer construct when compared with fixation using a single lag screw spanning 60% of the width of the sacral body. No mechanical advantage was observed between short screws inserted in positional vs. lag fashion. CLINICAL SIGNIFICANCE: Sacroiliac luxation fixation using 2 short screws creates a mechanically superior construct with a larger region of acceptable implant positioning and potentially reduced risk of iatrogenic injury compared with conventional fixation.

Medial epicondylar fissure fracture as a complication of transcondylar screw placement for the treatment of humeral intracondylar fissure.

OBJECTIVE: To report the incidence of medial epicondylar fissure fracture (MEFF) after medial-to-lateral transcondylar screw placement in dogs with humeral intracondylar fissure (HIF) and to identify risk factors for MEFF. STUDY DESIGN: Retrospective study. SAMPLE POPULATION: Seventy-four client-owned dogs (88 elbows). METHODS: Medical records of dogs surgically treated for HIF, and postoperative imaging studies were reviewed for demographics, fracture characteristics, and repair techniques. The width of the transcondylar screw was expressed relative to the height of the condyle. Screw angle and degree of countersinking were recorded. Information from case records and follow-up radiographs were used to identify complications. RESULTS: Medial epicondylar fissure fracture was identified in 10 elbows (11.4%) following medial-to-lateral transcondylar screw placement: 4 cases were detected intraoperatively, 2 on immediate postoperative radiographs, 1 during routine radiographic follow up, and 3 when radiographs were reviewed for this study. A larger relative screw size was found to increase the risk of MEFF (P = .004, OR = 1.5). Fifteen additional complications were identified in 13/80 elbows at a median of 6 weeks postoperatively (range 1-56 weeks). Screw loosening was the most frequent complication (n = 9) and was the only complication in dogs with MEFF (n = 3); MEFF tended to increase the risk of perioperative screw loosening (P = .06). CONCLUSION: Medial epicondylar fissure fracture occurred in 10/88 elbows treated for HIF and was more common in elbows treated with a larger screw size relative to the height of the condyle. CLINICAL SIGNIFICANCE: Placing transcondylar screws with a diameter inferior to 41% of the height of the condyle is recommended to avoid MEFF. Medial epicondylar fissure fracture appears to have a low clinical significance in the perioperative period, although its effect on long-term outcome remains unknown.