Phosphonic Acids for Interfacial Engineering of Transparent Conductive Oxides.

Transparent conducting oxides (TCOs), such as indium tin oxide and zinc oxide, play an important role as electrode materials in organic-semiconductor devices. The properties of the inorganic-organic interface-the offset between the TCO Fermi level and the relevant transport level, the extent to which the organic semiconductor can wet the oxide surface, and the influence of the surface on semiconductor morphology-significantly affect device performance. This review surveys the literature on TCO modification with phosphonic acids (PAs), which has increasingly been used to engineer these interfacial properties. The first part outlines the relevance of TCO surface modification to organic electronics, surveys methods for the synthesis of PAs, discusses the modes by which they can bind to TCO surfaces, and compares PAs to alternative organic surface modifiers. The next section discusses methods of PA monolayer deposition, the kinetics of monolayer formation, and structural evidence regarding molecular orientation on TCOs. The next sections discuss TCO work-function modification using PAs, tuning of TCO surface energy using PAs, and initiation of polymerizations from TCO-tethered PAs. Finally, studies that examine the use of PA-modified TCOs in organic light-emitting diodes and organic photovoltaics are compared.

Determining Band-Edge Energies and Morphology-Dependent Stability of Formamidinium Lead Perovskite Films Using Spectroelectrochemistry and Photoelectron Spectroscopy.

We show for the first time that the frontier orbital energetics (conduction band minimum (CBM) and valence band maximum (VBM)) of device-relevant, methylammonium bromide (MABr)-doped, formamidinium lead trihalide perovskite (FA-PVSK) thin films can be characterized using UV-vis spectroelectrochemistry, which provides an additional and straightforward experimental technique for determining energy band values relative to more traditional methods based on photoelectron spectroscopy. FA-PVSK films are processed via a two-step deposition process, known to provide high efficiency solar cells, on semitransparent indium tin oxide (ITO) and titanium dioxide (TiO2) electrodes. Spectroelectrochemical characterization is carried out in a nonsolvent electrolyte, and the onset potential for bleaching of the FA-PVSK absorbance is used to estimate the CBM, which provides values of ca. -4.0 eV versus vacuum on both ITO and TiO2 electrodes. Since electron injection occurs from the electrode to the perovskite, the CBM is uniquely probed at the buried metal oxide/FA-PVSK interface, which is otherwise difficult to characterize for thick films. UPS characterization of the same FA-PVSK thin films provide complementary near-surface measurements of the VBM and electrode-dependent energetics. In addition to energetics, controlled electrochemical charge injection experiments in the nonsolvent electrolyte reveal decomposition pathways that are related to morphology-dependent heterogeneity in the electrochemical and chemical stability of these films. X-ray photoelectron spectroscopy of these electrochemically treated FA-PVSK films shows changes in the average near-surface stoichiometry, which suggests that lead-rich crystal termination planes are the most likely sites for electron trapping and thus nanometer-scale perovskite decomposition.

Extremely Long-Lived Charge Donor States Formed by Visible Irradiation of Quantum Dots.

Using cyclic voltammetry under illumination, we recently demonstrated that CdS quantum dots (QDs) form charge donor states that live for at least several minutes after illumination ends, ∼12 orders of magnitude longer than expected for free carriers. This time scale suggests that the conventionally accepted mechanism of charge transfer, wherein charges directly transfer to an acceptor following exciton dissociation, cannot be complete. Because of these long time scales, this unconventional pathway is not readily observed using time-resolved spectroscopy to probe charge transfer dynamics. Here, we investigated the chemical nature of these charge donor states using cyclic voltammetry under illumination coupled with NMR spectroscopy, X-ray diffraction, X-ray photoelectron spectroscopy, and optical spectroscopy. Our data reveal that charges are stored locally rather than as free carriers, and the number of charges stored is dependent on the QD surface ligation and stoichiometry. Altogether, our results confirm that electrons are stored at ligated surface Cd, these sites are competent charge donors, and this storage is charge balanced by X-type ligand desorption. We found that charge storage occurs in every QD system studied, including CdS, CdSe, and InP capped with carboxylate and phosphonate ligands.

Reducing delamination of an electron-transporting polymer from a metal oxide for electrochemical applications.

Delamination of the electron-transporting polymer N2200 from indium tin oxide (ITO) in aqueous electrolytes is mitigated by modifying ITO with an azide-functionalized phosphonic acid (PA) which, upon UV irradiation, reacts with the polymer. The optical, electrochemical, and spectroelectrochemical properties of N2200 thin films are retained in aqueous and non-aqueous media.

The modification of indium tin oxide with phosphonic acids: mechanism of binding, tuning of surface properties, and potential for use in organic electronic applications.

Transparent metal oxides, in particular, indium tin oxide (ITO), are critical transparent contact materials for applications in next-generation organic electronics, including organic light emitting diodes (OLEDs) and organic photovoltaics (OPVs). Understanding and controlling the surface properties of ITO allows for the molecular engineering of the ITO-organic interface, resulting in fine control of the interfacial chemistries and electronics. In particular, both surface energy matching and work function compatibility at material interfaces can result in marked improvement in OLED and OPV performance. Although there are numerous ways to change the surface properties of ITO, one of the more successful surface modifications is the use of monolayers based on organic molecules with widely variable end functional groups. Phosphonic acids (PAs) are known to bind strongly to metal oxides and form robust monolayers on many different metal oxide materials. They also demonstrate several advantages over other functionalizing moieties such as silanes or carboxylic acids. Most notably, PAs can be stored in ambient conditions without degradation, and the surface modification procedures are typically robust and easy to employ. This Account focuses on our research studying PA binding to ITO, the tunable properties of the resulting surfaces, and subsequent effects on the performance of organic electronic devices. We have used surface characterization techniques such as X-ray photoelectron spectroscopy (XPS) and infrared reflection adsorption spectroscopy (IRRAS) to determine that PAs bind to ITO in a predominantly bidentate fashion (where two of three oxygen atoms from the PA are involved in surface binding). Modification of the functional R-groups on PAs allows us to control and tune the surface energy and work function of the ITO surface. In one study using fluorinated benzyl PAs, we can keep the surface energy of ITO relatively low and constant but tune the surface work function. PA modification of ITO has resulted in materials that are more stable and more compatible with subsequently deposited organic materials, an effective work function that can be tuned by over 1 eV, and energy barriers to hole injection (OLED) or hole-harvesting (OPV) that can be well matched to the frontier orbital energies of the organic active layers, leading to better overall device properties.

Soft Materials for Photoelectrochemical Fuel Production.

Polymer semiconductors are fascinating materials that could enable delivery of chemical fuels from water and sunlight, offering several potential advantages over their inorganic counterparts. These include extensive synthetic tunability of optoelectronic and redox properties and unique opportunities to tailor catalytic sites via chemical control over the nanoenvironment. Added to this is proven functionality of polymer semiconductors in solar cells, low-cost processability, and potential for large-area scalability. Herein we discuss recent progress on soft photoelectrochemical systems and define three critical knowledge gaps that must be closed for these materials to reach their full potential. We must (1) understand the influence of electrolyte penetration on photoinduced charge separation, transport, and recombination, (2) learn to exploit the swollen polymer/electrolyte interphase to drive selective fuel formation, and (3) establish co-design criteria for soft materials that sustain function in the face of harsh chemical challenges. Achieving these formidable goals would enable tailorable systems for driving photoelectrochemical fuel production at scale.

Surface-initiated synthesis of poly(3-methylthiophene) from indium tin oxide and its electrochemical properties.

Poly(3-methylthiophene) (P3MT) was synthesized directly from indium tin oxide (ITO) electrodes modified with a phosphonic acid initiator, using Kumada catalyst transfer polymerization (KCTP). This work represents the first time that polymer thickness has been controlled in a surface initiated KCTP reaction, highlighting the utility of KCTP in achieving controlled polymerizations. Polymer film thicknesses were regulated by the variation of the solution monomer concentration and ranged from 30 to 265 nm. Electrochemical oxidative doping of these films was used to manipulate their near surface composition and effective work function. Doped states of the P3MT film are maintained even after the sample is removed from solution and potential control confirming the robustness of the films. Such materials with controllable thicknesses and electronic properties have the potential to be useful as interlayer materials for organic electronic applications.

Rationalizing energy level alignment by characterizing Lewis acid/base and ionic interactions at printable semiconductor/ionic liquid interfaces.

Charge transfer and energy conversion processes at semiconductor/electrolyte interfaces are controlled by local electric field distributions, which can be especially challenging to measure. Herein we leverage the low vapor pressure and vacuum compatibility of ionic liquid electrolytes to undertake a layer-by-layer, ultra-high vacuum deposition of a prototypical ionic liquid EMIM+ (1-ethyl-3-methylimidazolium) and TFSI- (bis(trifluoromethylsulfonyl)-imide) on the surfaces of different electronic materials. We consider a case-by-case study between a standard metal (Au) and four printed electronic materials, where interfaces are characterized by a combination of X-ray and ultraviolet photoemission spectroscopies (XPS/UPS). For template-stripped gold surfaces, we observe through XPS a preferential orientation of the TFSI anion at the gold surface, enabling large electric fields (∼108 eV m-1) within the first two monolayers detected by a large surface vacuum level shift (0.7 eV) in UPS. Conversely, we observe a much more random orientation on four printable semiconductor surfaces: methyl ammonium lead triiodide (MAPbI3), regioregular poly(3-hexylthiophene-2,5-diyl (P3HT)), sol-gel nickel oxide (NiOx), and PbIx-capped PbS quantum dots. For the semiconductors considered, the ionization energy (IE) of the ionic liquid at 3 ML coverage is highly substrate dependent, indicating that underlying chemical reactions are dominating interface level alignment (electronic equilibration) prior to reaching bulk electronic structure. This indicates there is no universal rule for energy level alignment, but that relative strengths of Lewis acid/base sites and ion-molecular interactions should be considered. Specifically, for P3HT, interactions are found to be relatively weak and occurring through the π-bonding structure in the thiophene ring. Alternatively, for NiOx, PbS/PbIx quantum dots, and MAPbI3, our XPS data suggest a combination of ionic bonding and Lewis acid/base reactions between the semiconductor and IL, with MAPbI3 being the most reactive surface. Collectively, our results point towards new directions in interface engineering, where strategically chosen ionic liquid-based anions and cations can be used to preferentially passivate and/or titrate surface defects of heterogeneous surfaces while simultaneously providing highly localized electric fields. These opportunities are expected to be translatable to opto-electronic and electrochemical devices, including energy conversion and storage and biosensing applications.

Phosphonic acid functionalized asymmetric phthalocyanines: synthesis, modification of indium tin oxide, and charge transfer.

Metalated and free-base A(3)B-type asymmetric phthalocyanines (Pcs) bearing, in the asymmetric quadrant, a flexible alkyl linker of varying chain lengths terminating in a phosphonic acid (PA) group have been synthesized. Two parallel series of asymmetric Pc derivatives bearing aryloxy and arylthio substituents are reported, and their synthesis and characterization through NMR, combustion analysis, and MALDI-MS are described. We also demonstrate the modification of indium tin oxide (ITO) substrates using the PA functionalized asymmetric Pc derivatives and monitoring their electrochemistry. The PA functionalized asymmetric Pcs were anchored to the ITO surface through chemisorption and their electrochemical properties characterized using cyclic voltammetry to investigate the effects of PA structure on the thermodynamics and kinetics of charge transfer. Ionization energies of the modified ITO surfaces were measured using ultraviolet photoemission spectroscopy.

Photoelectrochemical processes in polymer-tethered CdSe nanocrystals.

We demonstrate the electrochemical capture of CdSe semiconductor nanocrystals (NCs), with thiophene-terminated carboxylic acid capping ligands, at the surfaces of electrodeposited poly(thiophene) films (i) poly((diethyl)propylenedixoythiophene), P(Et)(2)ProDOT; (ii) poly(propylenedioxythiophene), PProDOT; and (iii) poly(ethylenedioxythiophene), PEDOT, coupled with the exploration of their photoelectrochemical properties. Host polymer films were created using a kinetically controlled electrodeposition protocol on activated indium-tin oxide electrodes (ITO), producing conformal films that facilitate high rates of electron transfer. ProDOT-terminated, ligand-capped CdSe-NCs were captured at the outer surface of the host polymer films using a unique pulse-potential step electrodeposition protocol, providing for nearly close-packed monolayers of the NCs at the host polymer/solution interface. These polymer-confined CdSe NCs were used as sensitizers in the photoelectrochemical reduction of methyl viologen (MV(+2)). High internal quantum efficiencies (IQEs) are estimated for photoelectrochemical sensitized MV(+2) reduction using CdSe NCs ranging from 3.1 to 7.0 nm diameters. Cathodic photocurrent at high MV(+2) concentrations are limited by the rate of hole-capture by the host polymer from photoexcited NCs. The rate of this hole-capture process is determined by (a) the onset potential for reductive dedoping of the host polymer film; (b) the concentration ratio of neutral to oxidized forms of the host polymer ([P(n)]/[P(ox)]); and (c) the NC diameter, which controls its valence band energy, E(VB). These relationships are consistent with control of photoinduced electron transfer by Marcus-like excess free energy relationships. Our electrochemical assembly methods provide an enabling route to the capture of functional NCs in conducting polymer hosts in both photoelectrochemical and photovoltaic energy conversion systems.

Synthesis and colloidal polymerization of ferromagnetic Au-Co nanoparticles into Au-Co3O4 nanowires.

The preparation of cobalt oxide nanowires with gold nanoparticle (AuNP) inclusions (Au-Co(3)O(4) nanowires) via colloidal polymerization of dipolar core-shell NPs is reported. Polystyrene-coated ferromagnetic NPs composed of a dipolar metallic cobalt shell and a gold NP core (PS-AuCoNPs) were synthesized by thermolysis of octacarbonyldicobalt [Co(2)(CO)(8)] in the presence of AuNP seeds and polymeric ligands. The colloidal polymerization process of these dipolar PS-AuCoNPs comprises dipolar nanoparticle assembly and solution oxidation of preorganized NPs to form interconnected cobalt oxide nanowires via the nanoscale Kirkendall effect, with AuNP inclusions in every repeating unit of the one-dimensional mesostructure. Calcination of the polymer-coated nanowires afforded polycrystalline Au-Co(3)O(4) nanowires that were determined to be electroactive. Nanocomposite materials were characterized by transmission electron microscopy, field-emission scanning electron microscopy, X-ray diffraction, vibrating sample magnetometry, and cyclic voltammetry. We demonstrate that the optical and electrochemical properties of Au-Co(3)O(4) nanowires are significantly enhanced in comparison with hollow Co(3)O(4) nanowires prepared via colloidal polymerization.

A planar, chip-based, dual-beam refractometer using an integrated organic light-emitting diode (OLED) light source and organic photovoltaic (OPV) detectors.

We present a simple chip-based refractometer with a central organic light-emitting diode (OLED) light source and two opposed organic photovoltaic (OPV) detectors on an internal reflection element (IRE) substrate, creating a true dual-beam sensor platform. For first-generation platforms, we demonstrate the use of a single heterojunction OLED based on electroluminescence from an Alq(3)/TPD heterojunction (tris-(8-hydroxyquinoline)aluminum/N,N'-bis(3-methylphenyl)-N,N'-diphenylbenzidine) and light detection with planar heterojunction pentacene/C(60) OPVs. The sensor utilizes the considerable fraction of emitted light from conventional thin-film OLEDs that is coupled into guided modes in the IRE, instead of into the forward (display) direction. A ray-optics description is used to describe light throughput and efficiency-limiting factors for light coupling from the OLED into the substrate modes, light traversing through the IRE substrate, and light coupling into the OPV detectors. The arrangement of the OLED at the center of the chip provides for two sensing regions: a "sample" channel and a "reference" channel, with detection of light by independent OPV detectors. This configuration allows for normalization of the sensor response against fluctuations in OLED light output, stability, and local fluctuations (temperature) that might influence sensor response. The dual-beam configuration permits significantly enhanced sensitivity to refractive index changes, relative to single-beam protocols, and is easily integrated into a field-portable instrumentation package. Changes in refractive index (DeltaRI) between 10(-2) and 10(-3) RI units could be detected for single beam operation, with sensitivity increased to DeltaRI approximately 10(-4) RI units when the dual-beam configuration is employed.

Oxide contacts in organic photovoltaics: characterization and control of near-surface composition in indium-tin oxide (ITO) electrodes.

The recent improvements in the power conversion efficiencies of organic photovoltaic devices (OPVs) promise to make these technologies increasingly attractive alternatives to more established photovoltaic technologies. OPVs typically consist of photoactive layers 20-100 nm thick sandwiched between both transparent oxide and metallic electrical contacts. Ideal OPVs rely on ohmic top and bottom contacts to harvest photogenerated charges without compromising the power conversion efficiency of the OPV. Unfortunately, the electrical contact materials (metals and metal oxides) and the active organic layers in OPVs are often incompatible and may be poorly optimized for harvesting photogenerated charges. Therefore, further optimization of the chemical and physical stabilities of these metal oxide materials with organic materials will be an essential component of the development of OPV technologies. The energetic and kinetic barriers to charge injection/collection must be minimized to maximize OPV power conversion efficiencies. In this Account, we review recent studies of one of the most common transparent conducting oxides (TCOs), indium-tin oxide (ITO), which is the transparent bottom contact in many OPV technologies. These studies of the surface chemistry and surface modification of ITO are also applicable to other TCO materials. Clean, freshly deposited ITO is intrinsically reactive toward H(2)O, CO, CO(2), etc. and is often chemically and electrically heterogeneous in the near-surface region. Conductive-tip atomic force microscopy (C-AFM) studies reveal significant spatial variability in electrical properties. We describe the use of acid activation, small-molecule chemisorption, and electrodeposition of conducting polymer films to tune the surface free energy, the effective work function, and electrochemical reactivity of ITO surfaces. Certain electrodeposited poly(thiophenes) show their own photovoltaic activity or can be used as electronically tunable substrates for other photoactive layers. For certain photoactive donor layers (phthalocyanines), we have used the polarity of the oxide surface to accelerate dewetting and "nanotexturing" of the donor layer to enhance OPV performance. These complex surface chemistries will make oxide/organic interfaces one of the key focal points for research in new OPV technologies.

Ferrocene functional polymer brushes on indium tin oxide via surface-initiated atom transfer radical polymerization.

The synthesis and electrochemical characterization of ferrocene functional polymethacrylate brushes on indium tin oxide (ITO) electrodes using surface-initiated atom transfer radical polymerization (SI-ATRP) is reported. SI-ATRP of ferrocene-containing methacrylate (FcMA) monomers from a phosphonic acid initiator-modified ITO substrate yielded well-defined homo- and block (co)polymer brushes of varying molar mass (4,000 to 37,000 g/mol). Correlation of both electrochemical properties and brush thicknesses confirmed controlled SI-ATRP from modified ITO surfaces. The preparation of block copolymer brushes with varying sequences of FcMA segments was conducted to interrogate the effects of spacing from the ITO electrode surface on the electrochemical properties of a tethered electroactive film.

Site-isolated, intermolecularly photocrosslinkable and patternable dendritic quinacridones.

Quinacridone-cored dendrimers with photocrosslinkable cinnamate moieties on the periphery can be patterned down to 5 micron features while retaining luminescence.

An electroactive fiber optic chip for spectroelectrochemical characterization of ultra-thin redox-active films.

The first, fully integrated, planar fiber optic platform with spectroelectrochemical capabilities, termed the electroactive fiber optic chip (EA-FOC) is presented here. Spectroelectrochemical techniques provide complementary optical and electrochemical data which are important for applications ranging from thin film characterization to advanced sensor design. To create the EA-FOC a side-polished fiber optic is coated with a thin film of indium-tin oxide (ITO) as the working electrode and used to probe electrochemically-driven changes in absorbance for surface-confined redox species. A sensitivity enhancement of approximately 40 times higher than a transmission measurement is demonstrated for this first-generation EA-FOC, using the methylene blue (MB) redox couple, cycling between the visibly colored, oxidized form of MB, and its leuco (transparent) reduced form. Additionally, the EA-FOC is used to probe the redox spectroelectrochemistry of an electrodeposited thin film, about 0.3% of a monolayer, of the conducting polymer poly(3,4-ethylenedioxythiophene) (PEDOT). Unlike other waveguide formats, the EA-FOC offers an ease of use due to its ability to simply couple to light sources and detectors through standard fiber connectors to create a sensitive planar waveguide spectroelectrochemical platform.

Impact of Titanium Dioxide Surface Defects on the Interfacial Composition and Energetics of Evaporated Perovskite Active Layers.

This investigation elucidates critical Brønsted and Lewis acid-base interactions at the titanium dioxide (TiO2) surface that control the interfacial composition and, thus, the energetics of vacuum-processed methylammonium lead iodide (MAPbI3) perovskite active layers (PALs). In situ photoelectron spectroscopy analysis shows that interfacial growth, chemical composition, and energetics of co-deposited methylammonium iodide (MAI)/PbI2 thin films are significantly different on bare and (3-aminopropyl)triethoxysilane (APTES)-functionalized TiO2 surfaces. Mass spectroscopy analysis indicates that MAI dissociates into hydrogen iodide and methylamine in the gas phase and suggests that MAPbI3 nucleation is preceded by adsorption and coupling of these volatile MAI precursors. Prior to MAPbI3 nucleation on the bare TiO2 surface, we suggest that high coverages of methylamine adsorbed to surface defect sites (e.g., undercoordinated Ti atoms and hydroxyls) promote island-like growth of large, PbI2-rich nuclei that inhibit nucleation and lead to a thick substoichiometric interface layer that impedes charge transport and collection energetics. APTES functional groups passivate TiO2 surface defects and facilitate more conformal growth of small, PbI2-rich nuclei that enhance MAPbI3 nucleation and significantly improve interfacial energetics for charge transport and extraction. This work highlights the considerable influence of TiO2 surface chemistry on PAL composition and energetics, which are critical factors that impact the performance and long stability of these materials in emerging photovoltaic device technologies.

Planar fiber-optic chips for broadband spectroscopic interrogation of thin films.

A planar fiber-optic chip (FOC) has been developed using side-polished optical fibers and characterized for broadband absorbance and fluorescence detection of molecular films. FOC technology combines the sensitivity of an attenuated total reflection (ATR) element with the ease of use of fiber-optic-based spectrometers and light sources to create an improved platform for spectroscopic analysis of molecular adsorbates. A multi-mode optical fiber (core diameter = 50 mum, numerical aperture = 0.22, stepped refractive index profile) mounted in a glass V-groove block was side-polished to create a planar platform that allows access to the evanescent field escaping from the fiber core. For this generation of FOC technology, the exposed evanescent field has an interaction length of approximately 17.2 mm. The FOC platform was independently characterized through measurements of thin-film and bulk absorbing samples. The device performance was compared to the existing ATR technology and methods for increasing sensitivity of the FOC were investigated and validated. Additionally, we have demonstrated the ability of the FOC to both evanescently excite and collect fluorescence through guided modes of the optical fiber for a surface-confined luminescent semiconductor nanoparticle film (4 nm diameter, ligand capped, CdSe core). The FOC described here with a supported planar interface can facilitate the use of conventional planar deposition technologies and provide a robust planar platform that is amenable for incorporation into various sensor technologies.

Critical Interface States Controlling Rectification of Ultrathin NiO-ZnO p-n Heterojunctions.

Herein, we consider the heterojunction formation of two prototypical metal oxides: p-type NiO and n-type ZnO. Elementally abundant, low-cost metal oxide/oxide' heterojunctions are of interest for UV optical sensing, gas sensing, photocatalysis, charge confinement layers, piezoelectric nanogenerators, and flash memory devices. These heterojunctions can also be used as current rectifiers and potentially as recombination layers in tandem photovoltaic stacks by making the two oxide layers ultrathin. In the ultrathin geometry, understanding and control of interface electronic structure and chemical reactions at the oxide/oxide' interface are critical to functionality, as oxygen atoms are shared at the interface of the dissimilar materials. In the studies presented here the extent of chemical reactions and interface band bending is monitored using X-ray and ultraviolet photoelectron spectroscopies. Interface reactivity is controlled by varying the near surface composition of nickel oxide, nickel hydroxide, and nickel oxyhydroxide using standard surface-treatment procedures. A direct correlation between relative percentage of interface hydroxyl chemistry (and hence surface Lewis basicity) and the local band edge alignment for ultrathin p-n junctions (6 nm NiO/30 nm ZnO) is observed. We propose an acid-base formulism to explain these results: the stronger the acid-base reaction, the greater the fraction of interfacial electronic states which lower the band offset between the ZnO conduction band and the NiO valence band. Increased interfacial gap states result in larger reverse bias current of the p-n junction and lower rectification ratios. The acid-base formulism could serve as a future design principle for oxide/oxide' and other heterojunctions based on dissimilar materials.