The Effect of Firing Cycles on the Fit of Cobalt-Chromium Multiunit Prostheses Fabricated by Additive Manufacturing.

PURPOSE: The effect of annealing and firing cycle on the adaptation of cobalt-chromium (CoCr) restorations fabricated by additive manufacturing has been poorly documented. This study compared the marginal and internal fit of CoCr three-unit fixed dental prostheses before and after firing cycles. MATERIAL AND METHODS: The first right maxillary premolar (MP) and molar (MM) on a typodont model, were prepared with a circumferential 1.2 mm chamfer, 2 mm occlusal reduction, and total taper of 8 degrees, to receive 3-unit fixed dental prostheses (FDP). After the framework design, 20 framework specimens were fabricated using CoCr metal powder by selective laser melting. The replica technique was used for marginal and internal fit measurements in mesiodistal and buccolingual planes. The specimens were submitted to an annealing process, and to ceramic firing protocol. Measurements were repeated after each firing cycle. The data were compared by using Levene test, t-test, and analysis of variance (ANOVA) (α = 0.05). RESULTS: A significant difference was found in the total intaglio surface discrepancy between the 3 treatments. The annealing treatment induced a statistical difference in the discrepancy value compared to the as printed state (p = 0.028). A significant difference was detected between the initial manufacturing phase and the ceramic layering firing cycle (p = 0.003). CONCLUSIONS: Firing cycles induced an alteration of the frameworks adaptation.

A Comparison of the Surface and Mechanical Properties of 3D Printable Denture-Base Resin Material and Conventional Polymethylmethacrylate (PMMA).

PURPOSE: To study the surface and mechanical properties of 3D printed denture-base resin materials and compare them with conventional heat-cured polymethylmethacrylate (PMMA). MATERIALS AND METHODS: Three brands of 3D printed denture-base resin materials and one conventional heat-cured PMMA were tested in this study: NextDent 3D printed resin, Dentona 3D printed resin, ASIGA 3D printed resin, and Meliodent conventional PMMA. Sixty specimens (25 × 25 × 3 mm) were fabricated (n=15 per group) to perform the following tests: wettability, surface roughness, and microhardness. One hundred twenty specimens (65 × 10 × 3 mm) were fabricated (n=30 per group) and stored in distilled water at (37 ±1°C) for 7 days. Specimens (N = 15) in each group were subjected to the three-point bending test and impact strength test, employing the Charpy configuration on un-notched specimens. The morphology of the fractured specimens was studied under scanning electron microscope (SEM). Statistical analysis was performed using one-way ANOVA and Tukey-pairwise multiple comparisons with 95% confidence interval. P-values of ≤0.05 were considered significant. RESULTS: The conventional heat-cured specimens demonstrated the highest means of surface roughness (0.23 ± 0.07 µm), Vickers hardness number (18.11 ±0.65) and flexural strength (92.44 ±7.91 MPa), and the lowest mean of contact angle (66.71° ±3.38°). ASIGA group showed the highest mean of contact angle (73.44° ±2.74°) and the lowest mean of surface roughness (0.19 ±0.03 µm). The highest mean of impact strength was recorded in the Dentona group (17.98 ±1.76 kg/m2 ). NextDent specimens showed the lowest means of Vickers hardness number (16.20 ±0.93), flexural strength (74.89 ±8.44 MPa), impact strength (15.20 ±0.69 kg/m2 ), and recorded the highest mean of bending modulus (2,115.80 ±178.95 MPa). CONCLUSIONS: 3D printed resin exhibited noticeable differences in surface and mechanical properties between different brands and with conventional heat-polymerized PMMA.

Analysis of the effect magnitude of different parameters on smile attractiveness.

OBJECTIVE: To evaluate the effect magnitude of different parameters on smile attractiveness. MATERIALS AND METHODS: A reference and 13 images were produced by manipulating 13 parameters. Image rating was performed with a 4-point Likert scale from least attractive (1) to most attractive (4). Image raters included laypeople, dental students, dentists, and dental specialists. Friedman and Wilcoxon image were used for estimate of effect size. Parameters were classified into small (0.10- < 0.30), medium (0.30- < 0.5), or large (≥0.50). RESULTS: A total of 1040 people participated with good consistency (α = 0.861), and moderate reliability (0.64-0.7). The reference image had the highest rank (laypeople:11.79, dental background: 12.55). For effect size; gingival margin level (-0.11, -0.01), teeth width proportion (-0.09, -0.10), inverted smile arch (-0.09, -0.21), commissure line cant (-0.15, -0.17) and low smile (-0.24, -0.23) had small effect size; occlusal plane cant (-0.36, -0.49), midline cant (-0.36, -0.48), and midline shift (-0.37, -0.49) had medium effect size; diastema (-0.55, -0.54) and color (-0.56, -0.56) had large effect size for the laypeople and dental groups. High smile (-0.42, -0.51), incisor edge symmetry (-0.46, -0.54) had medium effect size in laypeople group and large effect size in the dental group. Width to length tooth proportion (-0.26, -0.39) had small effect size in the laypeople group and medium effect size in the dental group. CONCLUSIONS: Smile parameters had different effect magnitude on smile attractiveness and were classified into small, medium, or large parameters. Neither laypeople nor professionals have a collective judgment on what constitutes a beautiful smile. CLINICAL SIGNIFICANCE: This study investigated the effect magnitudes of 13 smile parameters and presented a small, medium, and large smile parameters classification. It should provide the clinician with an insight into the expected effect each parameter has on the smile.

Effect of CAD/CAM Bur Deterioration on the Surface Roughness of Ceramic Crowns.

PURPOSE: To evaluate the effect of repetitive milling on the surface roughness of ceramic crowns. MATERIALS AND METHODS: Twenty feldspathic ceramic crowns (VITABLOCS Mark II; Vita Zahnfabrik, Bad Säckingen, Germany) milled with hard milling protocol, and 20 zirconia crowns (5Y-TZP, inCoris TZI; Dentsply Sirona, York, PA) milled with soft milling protocol, using a 5-axis milling machine (inLab MC X5; Dentsply Sirona) were investigated. Atomic force microscopy (SPM SmartSPM™-1000) was used for surface roughness measurements (Ra, RMS). Pearson correlation between bur deterioration percentage as provided by the software of the milling machine and surface roughness was performed with an (r) range between 1 and -1. Trend analysis between the 2-half and among the 4-quarter bur lifetime was performed with linear contrast analysis and partial eta squared (η) for estimate of effect size. Analysis of mean variance between the zirconia and feldspathic ceramic groups was performed with a t-test, with α = 0.05. RESULTS: Correlation analysis showed small correlation for Ra, RMS (r = -0.02, -0.16 for the feldspathic ceramic crowns and r = 0.044, 0.034 for the zirconia crowns), and no significant differences for the 2-half and 4-quarter groups (p > 0.05) for both crown types. Estimate of effect size was rated as medium for the 2-half groups (Ra = 0.420, RMS = 0.395) and large for the 4-quarter groups (RA = 0.22, F = 1.48, RMS = 0.19, F = 1.26) for the feldspathic ceramic crowns, and small effect size for the 2-half groups (Ra = 0.18, RMS = 0.20) and the 4-quarter groups (Ra = 0.035, RMS = 0.037) for the zirconia crowns. There was no significant difference (p = 0.178, F = 0.016. p = 0.088, F = 0.002) between the feldspathic ceramic and zirconia crowns with medium and large effect size (0.45, 0.57) for RA and RMS. CONCLUSIONS: Milling zirconia and feldspathic ceramic crowns had small correlation between bur deterioration and surface roughness when the burs were used within their recommended lifetime. However, hard milled feldspathic ceramic crowns had higher surface roughness than the soft milled zirconia crowns. Bur deterioration had a larger effect on the surface roughness of the feldspathic ceramic crowns than the zirconia crowns.

Fit Alteration of Presintered Co-Cr and Zirconia Multiple-Unit Prostheses After Ceramic Layering.

PURPOSE: The fit alteration after ceramic layering of soft Cobalt-Chromium (Co-Cr) and zirconia is poorly documented. This study compared the marginal and internal fit of presintered Co-Cr and zirconia three-unit fixed dental prostheses before and after ceramic veneering. MATERIALS AND METHODS: Co-Cr master model was prepared and duplicated 60 times to receive three-unit fixed dental prostheses (FDPs). Sixty dies were prepared, scanned and assigned to 3 groups (n = 20/group), to receive the FDPs made of presintered Co-Cr (CS), presintered zirconia (CZ) and cast Ni-Cr (Wi). Each framework was seated on its specific cast. A replica technique was used for marginal and internal discrepancy measurements in mesiodistal and buccolingual planes. Frameworks were ceramic veneered. Results were compared before and after ceramic layering within each group. Data were analyzed using the Levene, t test, and ANOVA (α = 0.05). RESULTS: Significant difference was found when gaps were compared within groups for CS and CZ but not for Wi. At the abutments level, significant difference was found for both premolars and molars in the buccolingual planes (p < 0.001). A multiple comparison between materials tested showed significant differences between presintered and cast Ni-Cr. No significant difference was detected between CS and CZ (p = 1.000). CONCLUSIONS: Although ceramic layering increased the discrepancy for presintered Co-Cr and zirconia, the marginal adaptation remained clinically acceptable.

Should Digital Complete Dentures Be Part of A Contemporary Prosthodontic Education?

Digital complete dentures should be incorporated into a contemporary dental school education due to factors that include the substantial increase in the number of scientific publications devoted to digital dentures, the increased number of companies producing these prostheses, and the expanded use by practitioners. These factors increased recently due to multiple advantages of digital dentures that are described. Based on positive clinical experiences with such prostheses, preclinical curriculum changes were made with examples presented of both didactic and laboratory courses that now include digital dentures. Perspectives are presented regarding online laboratory procedures where a substantial portion can be performed at home through remote instruction.

CAD/CAM Complete Denture Systems and Physical Properties: A Review of the Literature.

PURPOSE: CAD/CAM complete dentures have increased in popularity and a wide variety of systems are currently available. These prostheses present many advantages for clinicians, technicians and patients. Subtractive manufacturing is used by most of the available systems while a few manufacturers use an additive manufacturing technique. This article describes the currently available systems and materials available for the fabrication of CAD/CAM complete dentures and reviews the literature relative to their physical properties. METHODS: A comprehensive review of the literature was completed to enumerate the currently available techniques to fabricate CAD/CAM complete dentures and discuss their physical properties. A search of English language peer-reviewed literature was undertaken using MEDLINE and PubMed on research articles published between 2000 and 2019. A hand search of relevant dental journals was also completed. RESULTS: The literature indicates the physical properties of CAD/CAM milled poly(methylmethacrylate) or PMMA as it is commonly described is superior to conventionally processed PMMA for the fabrication of complete dentures. CONCLUSION: The incorporation of CAD/CAM technology into complete denture design and fabrication streamlines the clinical and laboratory processes and provides improved physical properties that enhance denture quality.

Effect of Milling Protocols on Trueness and Precision of Ceramic Crowns.

PURPOSE: To investigate the effect of different milling protocols for different ceramic materials on the trueness and precision of milled ceramic crowns. MATERIALS AND METHODS: A definitive impression from a patient requiring a ceramic crown was used to fabricate forty glass ceramic crowns (VITABLOCS mark II, Vita Zahnfabrik) milled with wet, hard milling protocol, and 40 zirconia crowns (inCoris TZI, Dentsply, Sirona) milled with dry, soft milling protocol, using a 5-axis milling machine (inLab MC X5; Dentsply Sirona). Trueness and precision for different crown areas were evaluated with a 3D evaluation software (Geomagic Control X, 3D systems). Statistical analysis was performed between the 2 crown types with independent t-test, and analysis of variances followed by Bonferroni tests among crown areas for each crown. RESULTS: All areas of the glass ceramic crowns had higher trueness than the zirconia crown areas (p < 0.05). Crown areas of each crown type had significantly different trueness values (p < 0.001, F = 175.17 for glass crowns, p < 0.001, F = 35.04 for zirconia crowns). Glass crowns had 3.78 µm precision, while zirconia crowns had 4.12 µm precision, with a precision difference range between the 2 types of crowns from 0.32 µm for the inner surface to 6.5 µm for the marginal surface. CONCLUSIONS: Type of ceramic material and milling protocol affected trueness of the milled crown, with higher trueness for the hardmilled glass crowns than the soft milled zirconia crowns. Soft milled zirconia crowns were generally overmilled in comparison with the reference design and glass crowns. However, glass crowns exhibited more undermilling in thin and deep areas. The crown area affected trueness, with external areas having better trueness than internal areas. The 5-axis milling machine had high precision, which was minimally affected by the ceramic type, milling protocol, or crown area.

Factors Affecting Implant Stability Quotients at Immediately and Conventionally Loaded Implants in the Posterior Maxilla: A Split-Mouth Randomized Controlled Trial.

PURPOSE: To assess primary and secondary stability of variable-thread tapered implants in the posterior maxilla and analyze the impact of various factors on implant stability quotients (ISQs). MATERIALS AND METHODS: Twenty-six subjects received 3-4 adjacent implants in the maxillary premolar-molar sextants to replace bilateral tooth loss. The implants on one side were immediately loaded with a provisional fixed prosthesis regardless of their primary stability. The contralateral control implants were conventionally loaded. Bone quality was subjectively recorded and primary stability was assessed by means of insertion torque values (ITVs) and ISQs in 4 directions. Secondary stability was measured by ISQ at definitive prosthesis delivery (3-3.5 months postoperatively), and 12 months after definitive loading. The impact of measurement direction, loading protocol, time, site-related (bone quality, implant position, crestal buccal bone thickness, apical cortical anchorage), and implant-related (implant dimensions, abutment height) variables on ISQs was assessed. RESULTS: For logistic reasons, ISQs were obtained for only 18 patients with 60 test and 60 control implants. Most of the implants (82%) at baseline had their lowest ISQ on the buccal aspect. There were no significant differences between ISQs measured in the buccal and palatal directions, or between ISQs in the mesial and distal directions. The mean of buccal and palatal ISQs was significantly lower than the mean of the 2 interproximal measurements at all evaluation periods. ISQs were not significantly different between the 2 loading groups at any time point. All implants showed a time-dependent increase in ISQs. Baseline ISQ correlated weakly with bone quality and ITV. None of the variables had a significant impact on baseline ISQs, except for implants in second molar sites which showed poorer primary stability than first premolars. CONCLUSION: Measurement direction and time are the most significant parameters affecting ISQs of variable-thread tapered implants in the posterior maxilla.

Effect of Inlays, Onlays and Endocrown Cavity Design Preparation on Fracture Resistance and Fracture Mode of Endodontically Treated Teeth: An In Vitro Study.

PURPOSE: To evaluate the fracture resistance and failure modes of endodontically treated mandibular molars restored with different designs of inlays, onlays and endocrowns. MATERIALS AND METHODS: Extracted mandibular third molars (n = 180) were used. An access cavity was prepared on the occlusal surface of each tooth and the roots were obturated with gutta percha. All specimens were randomly divided into 6 groups (n = 30/group) according to the cavity design and the restoration material used. C: control group without access cavity preparation. IE: MOD inlay preparation with EverX Posterior (GC Europe) in the pulp chamber. IG: MOD inlay preparation with G-aenial Universal Flo (GC America) in the pulp chamber. OE: onlay preparation with EverX Posterior (GC Europe) in the pulp chamber. OG: onlay preparation with G-aenial Universal Flo (GC America) in the pulp chamber. EC: endocrown with an empty pulp chamber. All restorations were fabricated with CAD/CAM system using CERASMART® (GC Dental products Europe, Belgium) CAD/CAM blocks. Specimens were thermal-cycled and were subjected to a compressive load applied at 30° angle relative to the long axis of the tooth with a universal testing machine. Results were statistically analyzed by ANOVA followed by Tukey post hoc tests. Chi-square test and Fisher Exact tests were used for the comparisons among groups. RESULTS: The mean fracture strength was significantly different between the groups (p < 0.001); it was significantly highest for intact teeth, followed by endocrowns (p = 0.021). The strength was significantly lower for inlays (with G-aenial Universal Flo and EverX Posterior), intermediate for onlays with EverX Posterior followed by onlays with G-aenial Universal Flo. CONCLUSIONS: Endocrowns exhibited higher fracture resistance than other tested composite resin groups. Endocrowns and onlays showed a more favorable failure mode than inlay restorations.

Stainability of acrylic resin materials used in CAD-CAM and conventional complete dentures.

STATEMENT OF PROBLEM: The effect of staining beverages on the color of dentures made with computer-aided design and computer-aided manufacturing (CAD-CAM) is unknown. PURPOSE: The purpose of this in vitro study was to evaluate the stainability of acrylic resins used in CAD-CAM-fabricated complete dentures compared with conventional materials. MATERIAL AND METHODS: Acrylic resin denture teeth from 3 different manufacturers (2 conventional and 1 milled) were obtained (N=45). Denture base acrylic resin specimens were made with 3 different techniques (compression molding, injection molding, and milling) (N=45). Conventional and/or milled acrylic resins were used to make specimens comprising both denture teeth and denture base acrylic resins (4 conventional, 2 milled denture bases with bonded teeth, and 1 all-milled) (N=105). All specimens were then immersed in coffee, red wine, or distilled water as control. The CIELab color differences between before and after immersion were determined by using a VITA Easyshade spectrophotometer. The tooth-denture base interface of the denture blocks was evaluated visually for the presence of stain. The CIELab data were analyzed by using ANOVA, and chi-square test was used for visual assessment (α=.05). RESULTS: Significant interactions were found between each acrylic resin material and each staining solution immersion when compared with distilled water immersion (P<.001). Denture teeth had similar color change after immersion in coffee (P=.149), while the most pronounced color change was observed with Portrait teeth upon immersion in wine (P<.001). Injection-molded denture base specimens exhibited less color change upon staining in wine than compression-molded or milled specimens (P<.001). Upon staining in coffee, milled specimens were not significantly different from injection- (P=.053) and compression-molded specimens (P=.180). The chi-square test showed a significant association between processing technique and stain accumulation at the tooth-denture base interface when evaluated visually (P<.001). Stain accumulation was greatest with compression-molded specimens (58%), followed by injection-molded (43%) and milled specimens with bonded teeth (8%). Monolithic teeth with milled denture base had no stain deposits at the tooth-denture base interface. CONCLUSIONS: The stainability of milled acrylic resins was no better than that of conventional materials. However, CAD-CAM milled denture blocks with teeth and base acrylic resins had greater resistance to stain accumulation at the tooth-denture base interface than those of conventional processing methods.

Evaluation of Marginal and Internal Fit of Presintered Co-Cr and Zirconia Three-Unit Fixed Dental Prosthesis Compared to Cast Co-Cr.

PURPOSE: The precision of soft metal processing technologies is poorly documented. This study compared marginal and internal fit of presintered cobalt-chromium (Co-Cr) and zirconia three-unit fixed dental prostheses (FDPs) to cast Co-Cr. MATERIALS AND METHODS: Three-unit FDPs were prepared on metal dies (N = 60) from typodont preparations of the maxillary right first premolar and molar. A standardized preparation of a metal-ceramic restoration was done on abutment teeth. The dies (N = 60) were scanned and divided into three groups (n = 20/group) to receive the FDP made of presintered Co-Cr (Ceramill Si), presintered zirconia (Ceramill Zi), and cast Co-Cr (Girobond NB). Each framework was seated on its specific cast. A replica technique was used for marginal and internal discrepancies measurements in mesiodistal and buccolingual planes. Data were analyzed using the Levene test, t-test, and analysis of variance (α = 0.05). RESULTS: When the overall mean discrepancy values were compared in the mesiodistal plane, a significant difference was found between Ceramill Sintron and Ceramill Zi groups (p = 0.026). No significant difference was detected between Girobond NB and Ceramill Sintron groups and between Girobond NB and Ceramill Zi groups (p = 0.537 and p = 0.569, respectively). In the buccolingual plane, there was no significant difference in the overall mean discrepancy between the three groups: CS/CZ (p = 1.000), GI/CS (p = 0.51), and GI/CZ (p = 0.87). Significant differences at several measurement points were found at the inter or intramaterial level. The increase in discrepancy values between marginal and occlusal measurements was evident for the three groups. CONCLUSIONS: Presintered three-unit FDPs fabricated from zirconia and Co-Cr exhibited internal and marginal discrepancy values similar to cast Co-Cr. A significant difference was reported between CS and CZ in mesiodistal planes. The axial and marginal differences in values for the three tested groups were below or around the 120 µm clinically acceptable threshold except for the occlusal area. When comparing first premolar to first molar, the internal and marginal discrepancies were similar with no apparent distortion of the framework after the sintering process.

The Effect of Ceramic Type and Background Color on Shade Reproducibility of All-Ceramic Restorations.

PURPOSE: To investigate the effects of background color on shade reproduction using CAD/CAM zirconia and lithium disilicate ceramics. MATERIALS AND METHODS: A plastic tooth was prepared for an all-ceramic crown and scanned. Tooth-shaped light background dies were manufactured. Full-contour crowns were milled from translucent zirconia (ZT) and low translucency lithium disilicates (E [LT]). Copings from opaque zirconia (Z) and medium opacity lithium disilicate (E[MO]) ceramics were milled and layered with veneering porcelain to full contour. Metal copings were used to produce a dark background. Specimens were divided into 8 groups with 3 variables: background color, ceramic type, and translucency. Crowns were cemented using composite resin cement. Color was measured with a spectrophotometer. Color difference (∆E) was calculated using the CIEDE2000 formula between the specimens and the target shade, A1. Statistical analysis was performed using a nested design 3-way ANOVA and Tukey multiple comparisons. RESULTS: The closest ∆E to target shade was produced by E (LT) (2.13 ± 0.19) on the dark background. This increased significantly to 2.90 ± 0.19 on the light background (p = 0.03). The e.max (MO) groups significantly increased (p = 0.001) to 4.40 ± 0.22 and 4.47 ± 0.4, (p = 1.00) for the dark and light backgrounds, respectively. ∆E for the zirconia groups were higher and ranged from 4.85 ± 0.48 to 5.60 ± 0.48 in the ZT groups (p = 0.04) and 6.5 ± 0.82 to 7.75 ± 0.53 (p = 0.001) for Z groups from dark to light backgrounds. There was an overall lack of chromaticity between the specimens and the target shade A1 CONCLUSIONS: Ceramic color was affected by ceramic type, background, and translucency. Lithium disilicate appeared to be better than zirconia in shade reproduction. Less-opaque materials matched the target shade better, while opaque materials and low translucencies were more suitable for dark backgrounds.

Influence of Addition of Different Nanoparticles on the Surface Properties of Poly(methylmethacrylate) Denture Base Material.

PURPOSE: To evaluate and compare the surface properties (roughness and hardness) of poly(methylmethacrylate) denture base material modified with zirconium dioxide (ZNPs), silicon dioxide (SNPs), and diamond (DNPs) nanoparticles. MATERIALS AND METHODS: Two hundred sixty heat-polymerized acrylic resin disks (15 × 2 mm) were prepared. ZNPs, SNPs, and DNPs were added in concentrations of 0%, 0.5%, 1.0%, 2.5%, and 5.0% by weight of acrylic powder. This yielded a total of 13 groups for each test according to filler type and concentration (n = 10/group). The control group was made of pure acrylic. A mechanical polisher was used to standardize specimens' surfaces before testing. A profilometer and Vickers hardness indenter were used to test the surface roughness and hardness, respectively. ANOVA and Tukey post hoc tests were used for data analysis (α = 0.05). RESULTS: In comparison to control, results showed a nonsignificant increase in surface roughness (Ra ) of acrylic material after the addition of 0.5% nanoparticles (ZNPs p = 0.168, SNPs p = 0.166, and DNPs p = 0.177), while a significant increase was seen with all other concentrations (p ˂ 0.05). Ra values of ZNP and DNP groups were significantly higher than those of the SNPs group (p < 0.001). The addition of any of the fillers to acrylic denture base materials significantly increased the hardness (p ˂ 0.05), with ZNPs and DNPs having values lower than those of the SNPs group (p < 0.001). CONCLUSIONS: Although nanofiller addition increased the hardness of denture base material, Ra was adversely affected when the concentration exceeded 0.5%. Therefore, 0.5% is suggested to be the most appropriate ratio to improve hardness with acceptable Ra .

A Comparison of the Flexural and Impact Strengths and Flexural Modulus of CAD/CAM and Conventional Heat-Cured Polymethyl Methacrylate (PMMA).

PURPOSE: The introduction of computer-aided design/computer-aided manufacturing (CAD/CAM) technology to the field of removable prosthodontics has recently made it possible to fabricate complete dentures of prepolymerized polymethyl methacrylate (PMMA) blocks, which are claimed to be of better mechanical properties; however, no published reports that have evaluated mechanical properties of CAD/CAM PMMA. The purpose of this study was to compare flexural strength, impact strength, and flexural modulus of two brands of CAD/CAM PMMA and a conventional heat-cured PMMA. MATERIALS AND METHODS: 45 rectangular specimens (65 mm × 10 mm × 3 mm) were fabricated (15 CAD/CAM AvaDent PMMA specimens from AvaDent, 15 CAD/CAM Tizian PMMA specimens from Shütz Dental, 15 conventional Meliodent PMMA specimens from Heraeus Kulzer) and stored in distilled water at (37  ± 1°C) for 7 days. Specimens (N = 15) in each group were subjected to the three-point bending test and impact strength test, employing the Charpy configuration on unnotched specimens. The morphology of the fractured specimens was studied under a scanning electron microscope (SEM). Statistical analysis was performed using one-way ANOVA and Tukey pairwise multiple comparisons with 95% confidence interval. RESULTS: The Schütz Dental specimens showed the highest mean flexural strength (130.67 MPa) and impact strength (29.56 kg/m2 ). The highest mean flexural modulus was recorded in the AvaDent group (2519.6 MPa). The conventional heat-cured group showed the lowest mean flexural strength (93.33 MPa), impact strength (14.756 kg/m2 ), and flexural modulus (2117.2 MPa). Differences in means of flexural properties between AvaDent and Schütz Dental specimens were not statistically significant (p > 0.05). CONCLUSIONS: As CAD/CAM PMMA specimens exhibited improved flexural strength, flexural modulus, and impact strength in comparison to the conventional heat-cured groups, CAD/CAM dentures are expected to be more durable. Different brands of CAD/CAM PMMA may have inherent variations in mechanical properties.

Effect of Simulated Mastication on the Retention of Locator Attachments for Implant-Supported Overdentures: An In Vitro Pilot Study.

PURPOSE: Limited information is currently available relative to the effect of masticatory loads on the retentive properties of Locator attachments. The aims of this in vitro study were to assess and compare the effect of simulated mastication on the retention of white, pink, and blue Locator inserts for overdentures retained by 2 implants. MATERIALS AND METHODS: Thirty specimens simulating a nonanatomic edentulous flat ridge with two implants and an overdenture were divided into 3 groups according to the color of the fitted insert: transparent clear group (n = 10), pink group (n = 10), and blue group (n = 10). Retention forces were measured in an axial direction initially and after 100,000 cycles of simulated masticatory loads. One-way ANOVA followed by Tukey's post hoc tests were used to compare retention values and percentage retention loss between the 3 groups with significance set at p = 0.05. RESULTS: The 3 groups presented significant differences in retention at baseline (9.95 ± 1.91 N, 15.43 ± 4.08 N, and 41.73 ± 9.29 N for the blue, pink, and clear groups, respectively) and after simulated mastication (6.37 ± 2.64 N, 14.00 ± 3.89 N, 38.20 ± 5.11 N for the blue, pink, and clear groups, respectively). Within the same group, cyclic loading did not significantly affect retention in the clear and pink groups, while the blue inserts showed a significant retention loss (-37%) after loading. CONCLUSIONS: The results suggest that short-term simulated mastication affects the extra-light blue inserts but not the more-retentive inserts.

Comparative Effect of Glass Fiber and Nano-Filler Addition on Denture Repair Strength.

PURPOSE: To evaluate and compare the effects of glass fiber (GF), Zirconium oxide nanoparticles (nano-ZrO2 ), and silicon dioxide nanoparticles (nano-SiO2 ) addition on the flexural strength and impact strength of repaired denture base material. MATERIALS AND METHODS: Heat-polymerized acrylic resin specimens were fabricated. All specimens were sectioned centrally and beveled creating 2.5 mm repair gap except for 10 controls. Specimen grouping (n = 10/group) was done according to filler concentration of 0%, 0.25%, 0.5%, and 0.75% of auto-polymerized acrylic powder. Modified resin was mixed, packed in the repair gap, polymerized, finished and polished. Three-point bending test and Charpy type impact testing were done. Data were analyzed using one-way-ANOVA and Post-Hoc Tukey test (α = 0.05). RESULTS: All additives significantly increased flexural strength and impact strength (p < 0.05). Within the modified subgroups, no significant differences were found for GF. Significant increase for nano-ZrO2 and significant decrease for nano-SiO2 as the concentration of additive increased were noted for both flexural strength and impact strength. Highest flexural strength was found with 0.75%-nano-ZrO2 (69.59 ± 2.52MPa) and the lowest was found with 0.75%-nano-SiO2 (53.82 ± 3.10MPa). The 0.25%-nano-SiO2 showed the highest impact strength value (2.54 ± 0.21 kJ/m2 ) while the lowest impact strength value was seen with 0.75%-nano-SiO2 (1.54 ± 0.17 kJ/m2 ). CONCLUSION: Nano-filler effect was concentration dependent and its addition to repair resin increased the flexural and impact strengths. The incorporation of 0.75%-ZrO2 or 0.25%-SiO2 into repair resin proved to be a promising technique to enhance repair strength and avoid repeated fractures.

A comparison of the marginal and internal fit of porcelain laminate veneers fabricated by pressing and CAD-CAM milling and cemented with 2 different resin cements.

STATEMENT OF PROBLEM: The marginal and internal adaptations of porcelain laminate veneers (PLVs) are key elements in their long-term success. However, the marginal and internal fit obtained with a pressable material compared with computer-aided design and computer-aided manufacturing (CAD-CAM) needs further investigation as does the choice of cement used. PURPOSE: The purpose of this in vitro study was to evaluate the marginal and internal fit of PLVs fabricated using pressing and CAD-CAM milling and cemented using 2 types of composite resin cement. MATERIAL AND METHODS: Twenty PLVs were fabricated from VITA PM9 pressable material, and 20 veneers were milled using VITA Blocs Mark II. Veneers were cemented to composite resin dies using either RelyX Veneer cement or Variolink-N cement. Specimens were embedded in clear resin and sectioned incisogingivally and mesiodistally. Marginal discrepancy at the incisal and cervical positions and the internal gap at 6 different locations were evaluated by using a scanning electron microscope. Two-way ANOVA followed by Tukey multiple comparisons were used to examine difference among groups (α=.05). RESULTS: The cement and fabrication methods did not show any significant effect for absolute marginal gap (AMG) at the incisal edge, AMG at the cervical margin or marginal gap at the incisal edge. However, both had a significant effect on marginal gap at the cervical margin (P=.038 for the fabrication method and P=.050 for the cement used). Also, both cement and fabrication methods had a significant effect on internal gap average (P<.001). The lowest gap values were reported for veneers fabricated from VITA PM9 by using the press technique and cemented with RelyX Veneer cement. When the position of gap measurements was taken into consideration, it was the only significant factor (P<.001 for the effect of position on AMG and P<.001 for the effect of position on marginal gap). Gaps at the cervical position were significantly lower than gaps at the incisal position. CONCLUSIONS: Smaller marginal and internal discrepancies were recorded for PLVs fabricated by using the pressing technique and cemented using RelyX Veneer cement compared with milled veneers and Variolink-N cement. Larger discrepancies were present incisally than cervically.

The influence of simulated aging on the color stability of composite resin cements.

STATEMENT OF PROBLEM: Data for the color stability of dual-polymerized and light-polymerized resin cements used in esthetic dentistry are lacking. PURPOSE: The purpose of this in vitro study was to evaluate the color stability of 4 types of composite resin cements after water aging. MATERIAL AND METHODS: Specimens (n=30) of each resin cement (Variolink Esthetic LC, RelyX Ultimate DC, Nexus 3 DC, Nexus 3 LC) were prepared. The shade selected was Light+ for Variolink Esthetic, B 0.5 for RelyX Ultimate, and White for both Nexus 3 DC and LC. All 120 specimens were aged by water for 30 days at 37°C under dark conditions, using a thermocycling machine. The specimens' color characteristics (L*, luminosity; a*, red-green; b*, yellow-blue) and color differences (ΔE) were measured with a spectrophotometer before day 0, after day 1, and after 30 days of immersion. Statistical analysis used ANOVA and Tukey post hoc tests (α=.05). RESULTS: Considering ΔE<3.3 as clinically acceptable, results showed significant color variations for all cements (RelyX Ultimate=3.69; Nexus 3 LC=3.76; Nexus 3 DC=5.34), except for Variolink Esthetic (0.88). However, this variation was significantly less when day 1 was considered the baseline measurement, showing clinically acceptable ΔE values for all types of cement. CONCLUSIONS: Water aging had a significant effect on color stability; most color variations occurred in the first 24 hours of polymerization, with relatively nonsignificant variations afterwards.

Comparison of the effects of cement removal from zirconia and titanium abutments: An in vitro study.

STATEMENT OF PROBLEM: Excess cement around dental implants is a significant cause of peri-implant inflammation. Research has focused on approaches to cement removal, the type of cement used, and the different instruments used for cement removal with titanium abutments. However, data comparing zirconia with titanium abutments are lacking. PURPOSE: The purpose of this in vitro study was to compare the effectiveness of excess cement removal from zirconia and titanium custom abutments using an explorer and to compare the effects of cement removal on the abutment surfaces. MATERIAL AND METHODS: Implant analogs were placed in a cast in the position of the 2 maxillary central incisors. After creating similar emergence profiles for both the implant abutments, 18 zirconia and titanium custom abutments were fabricated with 1-mm subgingival finish lines on the facial and interproximal areas and an equigingival finish line on the palatal side. The crowns were cemented with zinc oxide-eugenol cement, and a steel explorer was used to remove the excess cement. All abutments were analyzed under a scanning electron microscope for cement remnants and scratches. RESULTS: The mean surface area of cement remnants on the zirconia abutments was 778 ±113 µm2, and for titanium abutments, it was 1123 ±252 µm2, which in terms of the mean percentage area was 3.27% of the total surface area of zirconia and 4.71% of titanium abutments. Only a few abutments from each group showed scratches, and no deep scratches or gouges were observed. CONCLUSIONS: Zirconia and titanium abutments had statistically similar cement remnants. Scratches were observed on only a few specimens.