Novel Collagen Surgical Patches for Local Delivery of Multiple Drugs.

Effective control of post-operative inflammation after tissue repair remains a clinical challenge. A tissue repair patch that could appropriately integrate into the surrounding tissue and control inflammatory responses would improve tissue healing. A collagen-based hybrid tissue repair patch has been developed in this work for the local delivery of an anti-inflammatory drug. Dexamethasone (DEX) was encapsulated into PLGA microspheres and then co-electrocompacted into a collagen membrane. Using a simple process, multiple drugs can be loaded into and released from this hybrid composite material simultaneously, and the ratio between each drug is controllable. Anti-inflammatory DEX and the anti-epileptic phenytoin (PHT) were co-encapsulated and released to validate the dual drug delivery ability of this versatile composite material. Furthermore, the Young's modulus of this drug-loaded collagen patch was increased to 20 KPa using a biocompatible riboflavin (vitamin B2)-induced UV light cross-linking strategy. This versatile composite material has a wide range of potential applications which deserve exploration in further research.

Melt Electrospinning of Nanofibers from Medical-Grade Poly(ε-Caprolactone) with a Modified Nozzle.

Melt electrospun fibers, in general, have larger diameters than normally achieved with solution electrospinning. This study uses a modified nozzle to direct-write melt electrospun medical-grade poly(ε-caprolactone) onto a collector resulting in fibers with the smallest average diameter being 275 ± 86 nm under certain processing conditions. Within a flat-tipped nozzle is a small acupuncture needle positioned so that reduces the flow rate to ≈0.1 µL h-1 and has the sharp tip protruding beyond the nozzle, into the Taylor cone. The investigations indicate that 1-mm needle protrusion coupled with a heating temperature of 120 °C produce the most consistent, small diameter nanofibers. Using different protrusion distances for the acupuncture needle results in an unstable jet that deposited poor quality fibers that, in turn, affects the next adjacent path. The material quality is notably affected by the direct-writing speed, which became unstable above 10 mm min-1 . Coupled with a dual head printer, first melt electrospinning, then melt electrowriting could be performed in a single, automated process for the first time. Overall, the approach used here resulted in some of the smallest melt electrospun fibers reported to date and the smallest diameter fibers from a medical-grade degradable polymer using a melt processing technology.

Advanced fabrication approaches to controlled delivery systems for epilepsy treatment.

INTRODUCTION: Epilepsy is a chronic brain disease characterized by unprovoked seizures, which can have severe consequences including loss of awareness and death. Currently, 30% of epileptic patients do not receive adequate seizure alleviation from oral routes of medication. Over the last decade, local drug delivery to the focal area of the brain where the seizure originates has emerged as a potential alternative and may be achieved through the fabrication of drug-loaded polymeric implants for controlled on-site delivery. AREAS COVERED: This review presents an overview of the latest advanced fabrication techniques for controlled drug delivery systems for refractory epilepsy treatment. Recent advances in the different techniques are highlighted and the limitations of the respective techniques are discussed. EXPERT OPINION: Advances in biofabrication technologies are expected to enable a new paradigm of local drug delivery systems through offering high versatility in controlling drug release profiles, personalized customization and multi-drug incorporation. Tackling some of the current issues with advanced fabrication methods, including adhering to GMP-standards and industrial scale-up, together with innovative solutions for complex designs will see to the maturation of these techniques and result in increased clinical research into implant-based epilepsy treatment. ABBREVIATIONS: GMP: Good manufacturing process; DDS(s): Drug delivery system(s); 3D: Three-dimensional; AEDs: Anti-epileptic drugs; BBB: Blood brain barrier; PLA: Polylactic acid; PLGA: Poly(lactic-co-glycolic acid); PCL: poly(ɛ-caprolactone); ESE: Emulsification solvent evaporation; O/W: Oil-in-water; W/O/W: Water-in-oil-in-water; DZP: Diazepam; PHT: Phenytoin; PHBV: Poly(hydroxybutyrate-hydroxyvalerate); PEG: Polyethylene glycol; SWD: Spike-and-wave discharges; CAD: Computer aided design; FDM: Fused deposition modeling; ABS: Acrylonitrile butadiene styren; eEVA: Ethylene-vinyl acetate; GelMA: Gelatin methacrylate; PVA: Poly-vinyl alcohol; PDMS: Polydimethylsiloxane; SLA: Stereolithography; SLS: Selective laser sintering.