Enhancing mouthguard longevity: Impact of surface treatment against aging from brushing and disinfectant exposure.

BACKGROUND/AIMS: The study aimed to assess the surface characteristics of sports mouthguards under mechanical stresses during cleaning, either by brushing or immersion in disinfectant solutions. MATERIAL AND METHODS: Ethylene-vinyl acetate samples, 4 mm thick, were randomly assigned to cleaning methods: control (C-no cleaning), brushing with water (B.W), brushing with neutral liquid soap (B.S), brushing with toothpaste (B.T), immersion in distilled water for 10 min (I.W), immersion in 2.25% sodium hypochlorite solution for 10 min (I.SH), and immersion in sodium bicarbonate solution for 5 min (I.SB). All cleaning methods were applied for 28 days. Surface roughness average (Ra) and wettability were measured at baseline for the control group (n = 9), and after cleaning for all the other groups. RESULTS: One-way ANOVA with Tukey tests (5% significance) indicated significant differences among groups (p < .05). The I.SB group had higher surface roughness than B.S and B.T (p < .05). B.W showed the lowest wettability, significantly lower than B.T, I.W, and I.SB (p < .05). I.SB exhibited the highest wettability, significantly different from sodium hypochlorite, neutral liquid soap, brushing with water, and control groups (p < .05). The sodium bicarbonate immersion group (I.SB) demonstrated greater statistical variation, displaying higher susceptibility to aging compared to brushing with neutral liquid soap. CONCLUSION: Cleaning mouthguards with a toothbrush, water, and neutral liquid soap emerged as the most promising method, causing minimal surface changes in the material.

Fatigue behavior, failure mode, and stress distribution of occlusal veneers: influence of the prosthetic preparation cusp inclinations and the type of restorative material.

OBJECTIVE: To evaluate the effects of cusp inclination of the prosthetic preparation's occlusal surface and type of restorative material on the fatigue behavior, failure mode, and stress distribution of occlusal veneers. MATERIALS AND METHODS: Glass fiber-reinforced epoxy resin prosthetic preparations for occlusal veneers with three different occlusal surface cusp inclination degrees (0°, 15°, and 30°) were produced and assigned into six testing groups (n = 11) according to the cusp inclination (0°, 15°, or 30°) and type of restorative material (lithium disilicate-LD or resin composite-RC). Despite different substrate preparation cusp inclination degrees, the restorations were designed maintaining 30° inclination between the cusps at the occlusal surface and a thickness of 0.7 mm at the central groove region of the restorations to be machined in a CAD/CAM system. After cementation, the specimens were stored for about 7 days (under water at 37 °C), and subsequently submitted to a load to failure test (n = 2) and an intermittent cyclic fatigue test (n = 9) (initial load: 100 N; step size: 50 N; cycles/step: 10,000; loading frequency: 20 Hz; loading piston: 6-mm-diameter stainless steel) until observing cracks. The data were analyzed by two-way ANOVA, Kaplan-Meier, and Mantel-Cox post hoc tests. Finite element analysis (FEA) and fractographic analyses were performed. RESULTS: The fatigue performance of LD and RC occlusal veneers was evaluated based on different prosthetic preparation cusp inclinations. The 0° inclination showed the best fatigue performance for both materials (LD: 944N, RC: 861N), while the 15° and 30° inclinations had lower values (LD: 800N and 533N, RC: 739N and 717N, respectively). The study also found that for a 0° inclination, LD occlusal veneers performed better than RC ones (LD: 944 N > RC: 861N), while for a 30° inclination, RC occlusal veneers had better fatigue performance than LD ones (LD: 533N < RC: 717N). No significant difference was observed between the materials for a 15° inclination (LD: 800N = RC: 739N). The FEA results showed a higher tensile stress concentration on lithium disilicate than on resin composite occlusal veneers. All lithium disilicate occlusal veneers showed radial crack failures, while resin composite occlusal veneers showed Hertzian cone cracks and radial cracks combined. CONCLUSION: Considering mechanical perspective only, RC occlusal veneers should be indicated when prosthetic preparation cusps inclinations are 30°. When 0° prosthetic preparation cusps inclinations are observed, LD occlusal veneers will behave mechanically better. When a 15° cusp inclination is preserved, both restorative materials behave similarly.

Effect of resin cement elastic modulus on the biaxial flexural strength and structural reliability of an ultra-thin lithium disilicate glass-ceramic material.

OBJECTIVES: Photo- and dual-polymerized resin-based luting agent was evaluated for elastic moduli effects on ultra-thin lithium disilicate (LD) glass-ceramic strengthening, structural reliability, and stress distribution. MATERIALS AND METHODS: One hundred-sixty LD discs (IPS e.max CAD, Ivoclar/Vivadent) were produced in ultra-thin thicknesses (half with 0.3 mm and the other half with 0.5 mm). The ultra-thin ceramic disks were coated with two different cement types (Variolink Veneer - V and Panavia F 2.0 - P). Two positive control groups were tested following hydrofluoric (HF) acid etching (LDt3, LDt5) and two negative control groups were tested for untreated ceramic (LD 3, LD 5). Biaxial flexural strength (BFS), characteristic strength (σ0) and Weibull modulus (m) were the response variables (n = 20) at the ceramic/resin cement interface (z = 0). Finite element analysis (FEA) was used to calculate maximum principal stress. Data were analyzed using two-way ANOVA, and Tukey's test. Scanning electron microscopy (SEM) was used to analyze the failed specimens using fractography and surface morphology. RESULTS: The BFS of LD at either thickness was not affected by cement types, as also demonstrated by FEA. Structural reliability significantly improved in the positive control group (LDt5). CONCLUSION: The cementation of ultra-thin LD with a resin-cement of varying elastic moduli did not influence BFS. LD surface modification by HF acid-etching increased the reliability. CLINICAL RELEVANCE: Ultra-thin anterior veneer designs made from lithium disilicate have been widely proposed and the apparent success of LD ultra-thin veneers was not influenced by the cement choice in the current studies albeit the elastic moduli luting agents used were of similar values.

Fatigue survival of endodontically treated teeth restored with different fiber-reinforced composite resin post strategies versus universal 2-piece fiber post system: An in vitro study.

STATEMENT OF PROBLEM: Various strategies have been proposed to reduce the cement space of foundation restorations for endodontically treated teeth. However, they may add more operative steps, or the dentist must keep different sizes of drills and posts in stock. A 2-piece universal adjustable post system has been developed to overcome this problem, but whether the system has acceptable fatigue survival performance is unclear. PURPOSE: The purpose of this in vitro study was to evaluate the fatigue survival and stress distribution of endodontically treated teeth without a ferrule and restored with different glass fiber post strategies versus a recently introduced universal 2-piece fiber post system. MATERIAL AND METHODS: Bovine incisor roots were randomly assigned to 3 groups as per the post used (n=13): adapted glass fiber post with post space preparation of the same size, composite resin-custom glass fiber post (CTM), and universal 2-piece glass fiber-reinforced composite resin post (UNI). The posts were adhesively luted, the composite resin core was added, and a composite resin crown was produced with computer-aided design and computer-aided manufacturing (CAD-CAM), and then adhesively luted to each core. A fatigue test was performed with the stepwise stress method (10 000 cycles/step; 20 Hz; load=100 N to 750 N; step=50 N) until fracture, and the failure mode analyzed. The stress distribution was evaluated by finite element analysis with the maximum principal stress criteria by following the parameters of the in vitro test. The solids were considered homogeneous, linear, and isotropic, except for the glass fiber post (orthotropic), and a load of 450 N at 30 degrees was applied. The fatigue failure load and the number of cycles for failure were analyzed with Kaplan-Meier and Mantel-Cox (log rank test) (α=.05). The finite element analysis results were analyzed with colorimetric graphs. RESULTS: The highest fatigue failure load and the number of cycles for failure were found in the UNI system, whereas the lowest results were found in the CTM group. All groups exhibited repairable failures. The finite element analysis showed the lowest stress in root dentin in the UNI system. The CTM system had the largest stress regions at the dentin and dentin-core interface. CONCLUSIONS: The use of a 2-piece universal glass fiber post system resulted in more fatigue behavior compared with composite resin-custom glass fiber posts.

Fatigue resistance of polymeric restorative materials: effect of supporting substrate.

The objective of this study was to investigate the effect of mismatch between the elastic properties of substrate and restorative material on the fatigue resistance and stress distribution of multilayer structures. The tested hypotheses were that (1) both an indirect composite resin (IR) and a polymer-infiltrated ceramic network (PICN) would show a higher survival rate after cyclic loading when cemented to a substrate with a high elastic modulus (E); and (2) PICN structures would have higher survival rates than IR structures regardless of the supporting substrate. Blocks of PICN and IR were cut to obtain 1.0-mm-thick sections, which were cemented to substrates with different E values: c, core resin cement (low E); r, composite resin (intermediate E); and m, metal (nickel-chromium alloy; high E). The resulting 6 groups of specimens (n = 20 per group) were subjected to a cyclic fatigue test (106 cycles). Stress distribution was verified using finite element analysis, and the risk of failure was estimated. Fatigue data were analyzed using Kaplan-Meier and Holm-Sidák tests. The χ2 test was used to evaluate the type of crack. The groups IRc, IRr, and PICNm had the highest survival rates after cyclic loading and were statistically similar to each other. Their survival rates were significantly greater than those of the IRm, PICNr, and PICNc groups (P < 0.001), which were all significantly different from each other (P < 0.001). There was a significant relationship between the experimental group and type of crack (P < 0.001). Specimens cemented to core resin cement and composite resin substrates showed predominantly radial cracks, while those cemented to nickel chromium alloy had predominantly cone cracks. The risk of failure values revealed that PICN was more sensitive to the type of substrate than IR. PICN has greater fatigue-resistant behavior when cemented to a substrate with a high E value, while IR has superior performance when substrates with lower and intermediate E values are used.

Fracture resistance and biomechanical behavior of different access cavities of maxillary central incisors restored with different composite resins.

OBJECTIVES: The aim of this study was to compare the effect of three different access cavities on the tissue removal, deflection, fracture resistance, and stress distribution of extracted maxillary central incisors. MATERIALS AND METHODS: Forty human maxillary central incisors were randomly assigned in four experimental group (n = 10) including conservative access cavity "CAC," traditional access cavity "TAC," invasive access cavity "IAC," and without access cavity (control group). Cone-beam computed tomography "CBCT" scans were used to evaluate the tissue removal during the different access cavities. All specimens were restored with composite resin (Admira Fusion, Voco, Cuxhaven, Germany) and embedded in acrylic resin blocks after simulating the periodontal ligament using red wax, then the specimens were submitted to the deflection test applying a load of 250 N and to the load-to-fracture test after artificial aging in a mechanical cycling machine (150 N, 5 × 106 cycles, 10 Hz). Lastly, stress distribution was assessed by three-dimensional finite element analysis (3D-FEA), simulating the specimens restoration by two types of composite resins of low and high elastic modulus (8 and 18 GPa respectively) after the access cavities. The data were submitted to Shapiro-Wilk and KS normality tests. Then, they were analyzed by one-way ANOVA and Tukey tests with a significance level (α ≤ 0.05). RESULTS: CBCT scans showed a significant difference of worn tissues in CAC and TAC when compared to the IAC (P < 0.0001). In deflection test, CAC showed lower deformation values than the TAC and IAC. Load-to-fracture test presented no significant difference among the three experimental groups (P = 0.6901). 3D-FEA showed that the more conservative the access cavity, the higher the stress magnitude. CONCLUSIONS: CAC promote less worn tissue; however, this does not improve the stress distribution or fracture resistance of endodontically treated maxillary incisors. CLINICAL RELEVANCE: Clinicians should reconsider the pros and cons of the conservative access cavity.

Fracture resistance and stress distribution of weakened teeth reinforced with a bundled glass fiber-reinforced resin post.

OBJECTIVES: To make an in vitro assessment of fracture resistance of weakened and non-weakened teeth receiving intraradicular reinforcement using Rebilda bundled glass fiber-reinforced composite posts (GT), Rebilda conventional glass fiber posts (RP), or both systems combined (GT + RP). MATERIALS AND METHODS: Eighty sound bovine incisors were prepared and divided randomly into eight groups as follows: (a) nWnR: without simulating weakness, and without intraradicular reinforcement; (b) WnR: simulating weakness, but without intraradicular reinforcement; (c) nWGT: without simulating weakness, but with GT; (d) WGT: simulating weakness, and with GT; (e) nWRP: without simulating weakness, but with RP; (f) WRP: simulating weakness, and with RP; (g) nWGTRP: without simulating weakness, but with GT + RP; (h) WGTRP: simulating weakness, and with GT + RP. The specimens were subjected to the load-to-fracture test using the DL-2000MF universal testing machine. The finite element method assessed the mechanical behavior and stress distribution in endodontically treated teeth. RESULTS: The groups nWGTRP and WGTRP presented the best results in the load-to-fracture test, with the former being better than the latter, but with no statistically significant difference (P > 0.05). However, there was a significant difference between these and the other groups (P < 0.05), except for nWRP. Stress distribution inside the canal wall was different among the groups, with promising mechanical behavior for nWGTRP and nWRP. CONCLUSIONS: The Rebilda conventional fiber post (RP), combined with the Rebilda bundled glass fiber-reinforced composite post (GT) improves the resistance and stress distribution of immature teeth. CLINICAL RELEVANCE: Longitudinal fracture is less frequent in teeth restored with GT and RP posts.

Fabrication and characterization of low-shrinkage dental composites containing montmorillonite nanoclay.

Dental composites are aesthetic materials widely used in Dentistry for replacing hard dental tissues lost due to caries or traumas. The aim of this study was to fabricate low-shrinkage dental composite charged with nanoclay fillers (montmorillonite Cloisite®-MMT) and evaluate their cytotoxicity and physicomechanical properties. Four dental composites were produced from the same organic matrix: Bis-GMA/TEGDMA (30 wt.%). The filler system was constituted of BaSi, SiO2, and MMT in the following concentrations (wt.%): 93.8/6.2/0, 89.1/5.9/5, 86.7/5.8/7.5, and 84.4/5.6/10 (E0: 0; E5: 5%; E7.5: 7.5%; E10: 10% of MMT nanoclays). The following properties were tested: in vitro cytotoxicity, flexural strength, elastic modulus, volumetric shrinkage, water sorption, water solubility, and hygroscopic expansion. Scanning electron microscopy was used to characterize composites' topography. Data were analyzed by one-way ANOVA and Tukey's HSD post hoc test (p < 0.05). MMT nanoclays did not affect the cytotoxicity. E5 and E7.5 groups showed a significant decrease in polymerization shrinkage while maintained the overall physicomechanical properties. The inclusion of 5 and 7.5 wt.% of MMT nanoclays allowed the fabrication of dental composites with low cytotoxicity and low polymerization shrinkage, without jeopardizing the overall behaviour of their physicomechanical properties (flexural strength, elastic modulus, water sorption, water solubility, and hygroscopic expansion). These aspects suggest that the usage of MMT nanoclays could be an effective strategy to formulate new dental composites with clinical applicability.

Canine guidance reconstruction with ceramic or composite resin: A 3D finite element analysis and in vitro wear study.

STATEMENT OF PROBLEM: Wear of the maxillary canine cusps is a common clinical condition which can affect function and esthetics and, in some situations, lead to occlusal pathology. The mechanical behavior of different restorative techniques for the condition is unclear. PURPOSE: The purpose of this in vitro study was to evaluate the biomechanical behavior of direct or indirect restorative techniques used in restoring canine guidance. MATERIAL AND METHODS: Three-dimensional models obtained from 10 extracted undamaged maxillary canines were modeled by using reverse engineering. Each model received 2 different preparations: incisal (I) or incisal and labial (IL), restored with composite resin (CR) or ceramic (C), compared with unrestored teeth (U). Finite element analysis was used to evaluate the total deformation and the maximum principal stress. For the in vitro wear test, 30 teeth were divided into groups: U (control), I-CR, and IL-C. The teeth were wear tested for 240 000 cycles with a 2-mm sliding contact, a load of 49 N applied, with a 4-Hz cycle with a composite resin piston as antagonist. The wear of restorations and antagonists was quantified by the digital image correlation technique. The 1-way analysis of variance test for total deformation and the Tukey test for the maximum principal stress were used (α=.05) to statistically analyze the data. The Friedman test was applied in the comparison between wear cycles, and the Tukey test was used in the comparison among groups. RESULTS: No significant difference was found among groups (P>.05) for the total deformation. IL-CR showed a higher failure probability, reaching stress peaks which exceeded the tensile strength of the material. I-CR showed greater wear in the in vitro test than IL-C (P=.02). No difference was found among groups in antagonist wear (P=.074). CONCLUSIONS: Ceramic restorations with labial involvement show biomechanical behavior closer to that of unrestored teeth in restoring canine guidance compared with composite resin.

Impact of different complete coverage onlay preparation designs and the intraoral scanner on the accuracy of digital scans.

STATEMENT OF PROBLEM: The trueness and precision of intraoral scanners (IOSs) and the effect of intracoronal restorations have been reported. However, studies addressing the accuracy of IOSs in reproducing different complete coverage onlay preparation designs are lacking. PURPOSE: The purpose of this in vitro study was to evaluate the influence of complete coverage onlay preparation design and intraoral scanning devices on the accuracy of digital scans in terms of trueness and precision. MATERIAL AND METHODS: Three preparation designs on the mandibular first molar were considered: a traditional preparation design with isthmus reduction (IST), a traditional preparation design without isthmus reduction (wIST), and simplified nonretentive preparation (nRET). Digital scans of epoxy resin mandibular arch reference models of the preparations (containing second premolar, first molar, and second molar) were obtained by using 3 IOSs (iTero Element 2 [ELE], Trios 3 [TRI], and Primescan [PRI]) (n=10). Trueness (µm) and precision (µm) were analyzed by superimposing the digital scan on the digital reference models obtained with a high-accuracy industrial scanner (ATOS Core 80) in a tridimensional metrology software program. Accuracy was quantified by the absolute deviation (µm). Local and overall mean positive and negative deviations for trueness were also obtained. Data were analyzed by using the Kruskal-Wallis and Dunn tests with a statistical software program (α=.05). RESULTS: The nonretentive preparation groups obtained higher trueness (3.8 µm) and precision (2.7 µm) than the IST and wIST groups (trueness=7.5 to 6.3 µm, precision=5.5 to 4.6 µm). Trueness values were lower with ELE×IST (16 µm), followed by ELE×wIST (13 µm), and PRI×IST (7.8 µm). In general, no difference was found between PRI and TRI scanners (6.3 to 5.9 µm), with lower performance for ELE (13 µm). Positive deviations were higher on the proximal box of the IST and wIST preparation and on the occlusal box of the IST group. Negative deviation was higher on the ELE×IST occlusal box. CONCLUSIONS: Different intraoral scanners and preparation designs influenced the accuracy of digital scans. A more complex preparation such as IST and wIST showed higher deviation. The iTero Element 2 scanner exhibited higher deviation for both trueness and precision.

Effect of Biologically Oriented Preparation Technique on the Stress Concentration of Endodontically Treated Upper Central Incisor Restored with Zirconia Crown: 3D-FEA.

The aim of this study was to evaluate the effect of biologically oriented preparation technique on the stress concentration of endodontically treated upper central incisors restored with zirconia crown (yttria-stabilized zirconia polycrystalline ceramic) through finite element analysis (FEA). Four models of maxillary central incisors containing enamel, dentin, periodontal ligament, cortical and medullary bone were created in CAD. Each model received a polymeric core-build up with nanofilled dental resin composite. The evaluated models were SM-preparation in shoulder 90°; CM-chamfer preparation; BOPT-biologically oriented preparation technique and BOPTB-BOPT preparation 1 mm below the cement-enamel junction. All models received zirconia crowns (5Y-TZP), fiberglass post and 1 mm ferrule. The models were imported into the analysis software with parameters for mechanical structural testing using the maximum principal stress and the tensile strength as the analysis criteria. Then, load of 150 N was applied at the cingulum with 45° slope to the long axis of the tooth, with the fixed base for each model. The type of marginal preparation affected the stresses concentration in endodontically treated teeth and in the zirconia crown margin. Considering the stress magnitude only, BOPT is a viable option for anterior monolithic zirconia crowns; however, with the highest stress magnitude at the restoration margin.

Scaffolds of PCL combined to bioglass: synthesis, characterization and biological performance.

Biomaterials may be useful in filling lost bone portions in order to restore balance and improve bone regeneration. The objective of this study was to produce polycaprolactone (PCL) membranes combined with two types of bioglass (Sol-Gel and melt-quenched) and determine their physical and biological properties. Membranes were produced through electrospinning. This study presented three experimental groups: pure PCL membranes, PCL-Melt-Bioglass and PCL-Sol-gel-Bioglass. Membranes were characterized using Scanning Electron Microscopy, Fourier Transform Infrared Spectrophotometry (FTIR), Energy-Dispersive Spectroscopy and Zeta Potential. The following in vitro tests were performed: MTT assay, alkaline phosphatase activity, total protein content and mineralization nodules. Twenty-four male rats were used to observe biological performance through radiographic, fracture energy, histological and histomorphometric analyses. The physical and chemical analysis results showed success in manufacturing bioactive membranes which significantly enhanced cell viability and osteoblast differentiation. The new formed bone from the in vivo experiment was similar to that observed in the control group. In conclusion, the electrospinning enabled preparing PCL membranes with bioglass incorporated into the structure and onto the surface of PCL fibers. The microstructure of the PCL membranes was influenced by the bioglass production method. Both bioglasses seem to be promising biomaterials to improve bone tissue regeneration when incorporated into PCL.

Different combinations of CAD/CAM materials on the biomechanical behavior of a two-piece prosthetic solution.

AIM: This study evaluated the stress distribution of implant-supported prostheses, varying the different combinations of computer-aided design/computer-aided manufacturing (CAD/CAM) materials between the hybrid abutment and the monolithic crown by three-dimensional (3D) finite element analysis (FEA). MATERIALS AND METHODS: Nine models were designed with Rhinoceros 3D and Ansys software. Each model contained a bone block of the molar area, including an implant (IH; Ø 3.75 × 11 mm) supporting a hybrid abutment (ceramic mesostructure (MS) cemented onto a titanium [Ti] base) and a monolithic crown. The occlusal load was applied to the fossa bottom (300 N; 30 degrees). The results were analyzed using the von Mises stress for each separated prosthetic structure and microstrain for the bone tissue. RESULT: Von Mises maps of the crown, ceramic MS, implant, screw, and cement layers showed a decreased stress concentration as the elastic modulus (E modulus) of the ceramic crown (CR) associated with a rigid ceramic MS decreased. No differences in bone tissue regarding microstrain were observed. CONCLUSION: Implant-supported crowns present less stress concentration when a rigid abutment is associated with resilient crowns.

Do Mechanical Advantages Exist in Relining Fiber Posts with Composite Prior to its Cementation?

PURPOSE: To evaluate two different techniques for glass fiber-reinforced resin post (FRC) insertion by assessing the stress distribution under polymerization shrinkage or masticatory loading and measuring the pull-out bond strength to dentin. MATERIALS AND METHODS: A model of an endodontically treated maxillary central incisor was used for three-dimensional simulation with two conditions: conventionally cemented (FRC) and relined (RFRC). The volumetric solids were exported to analysis software (ANSYS 17.2, ANSYS) in STEP (Standard for the Exchange of Product Data) format. All contacts were considered perfectly bonded between the geometries. Numerical models received a load of 100 N (45 degrees) on the lingual surface. The composite cement polymerization shrinkage was simulated by thermal analogy to obtain Von Mises, maximum principal stress, and shear stress. For in vitro evaluation, a pull-out bond strength test (n = 20/N = 40) was performed (50 Kgf, 1 mm/min) after mechanical cycling (in water at 37°C, 84 N, 2 bar, 45 degrees, 106 cycles, 4 Hz), and failure analysis was subsequently performed. The results were analyzed using one-way ANOVA and Tukey's test (α < 0.05). RESULTS: The FRC group showed more stress concentration in the cement layer. The RFRC group [(32 ± 13); (288 ± 129)] presented better performance than the FRC group [(6 ± 7); (152 ± 87)] for stress distribution and bond strength (p < 0.05). Adhesive and mixed failures occurred in both groups. CONCLUSION: Relined fiberglass posts reduced the stress generated by polymerization shrinkage and showed greater bond strength to dentin.

Validation of a Simplified Implant-Retained Cantilever Fixed Prosthesis.

PURPOSE: To evaluate the stress and strain generated in a fixed four-element prosthesis under the application of axial and nonaxial loads using a simplified implant-supported fixed prosthesis model. MATERIALS AND METHODS: A 3-dimensional model was constructed containing 3 implants with a conventional anatomical prosthesis (G1). The second model with the same implant system received the simplified prosthesis (G2). A load of 300 N was applied at an axial point and a nonaxial point through finite element analysis software. RESULTS: The G2 group showed different values of stress concentration in the prosthesis, fixation screw, retention screw, and abutments when compared with G1. Within a limit of 10% degrees of acceptability, the stress on the implants and the bone strain were enclosed for both models of prostheses. CONCLUSION: The simplified fixed prosthesis evaluated presents biomechanical behavior similar to an anatomical prosthesis in the implants and in the surrounding bone structure.

Influence of custom-made and stock mouthguard thickness on biomechanical response to a simulated impact.

BACKGROUND/AIMS: Mouthguards (MGs) are devices that can reduce the risks of facial trauma. However, the large variety of MG types and thicknesses raises the question of which type is the most effective and beneficial for the athletes. The aim of this study was to evaluate stress distribution in the skull, teeth, and jaws as a consequence of a direct impact. MATERIAL AND METHODS: Using modeling software, a human skull was modeled and a human jaw was created with all teeth inserted into the respective alveolus. The models were divided according to the MG type (custom-made or stock) and thickness (1, 2, and 4 mm). Two models without MG were evaluated with and without teeth contact. The geometries were exported to analysis software and the materials were considered ideal. Fixation occurred at the base of the foramen magnum. The load (500 N) was applied on the canine tooth with a ball. Maximum principal (MPa) and Von-Mises results were obtained. RESULTS: Without any protection, the generated tensile stress was of greater magnitude causing more damage in the absence of teeth contact. The presence of a MG significantly reduced the generated stress in all structures, and the customized/individualized type was more efficient than stock MGs. CONCLUSIONS: In extreme situations when it is impossible to use a MG, keeping the teeth in maximum intercuspal position is less harmful. Despite this, the use of any MG is beneficial and assists in dampening the generated stress. The thicker the device, the greater the capacity for decreasing the damage in all structures. The use of individual protectors for each patient is even more beneficial for preventing trauma during at-risk activities of impact.

Fracture load of complete-arch implant-supported prostheses reinforced with nylon-silica mesh: An in vitro study.

STATEMENT OF PROBLEM: Complete-arch implant-supported prostheses without a framework have a high risk of failure: a straightforward and inexpensive reinforcement material, such as nylon mesh, could improve their longevity. PURPOSE: The purpose of this in vitro study was to evaluate a nylon-silica mesh compound on the fracture strength of acrylic resin and the fracture load of complete-arch implant-supported prostheses. MATERIAL AND METHODS: Twenty-four complete mandibular arch implant-supported prostheses were divided into 2 groups according to cantilever length (molar and premolar) and subdivided into another 2 subgroups according to the presence or absence of reinforcing mesh. The specimens were submitted to a maximum load-to-fracture test in a universal testing machine, with a 100-N load cell, a 2 mm/min crosshead speed, and a spherical metal tip diameter of 4 mm at different points (molar and premolar). These were submitted to 1-way analysis of variance for repeated measurement and the post hoc Tukey multiple comparison test (α=.05). RESULTS: The mean maximum load ±standard deviation for the molar group was 393.4 ±95.0 N with reinforcement and 305.4 ±76.3 N without reinforcement (P=.02); and for the premolar group was 1083.3 ±283.7 N with reinforcement and 605.3 ±90.5 N without reinforcement (P=.001). CONCLUSIONS: Reinforcement with nylon mesh increased the mean maximum load of implant-supported complete-arch prostheses at both cantilever lengths. The cantilever to the premolar (5 mm) presented the highest maximum load values to fracture.

The Role of New Removable Complete Dentures in Stimulated Salivary Flow and Taste Perception.

PURPOSE: To evaluate the effect of replacement of inadequate complete dentures on salivary flow and taste perception in geriatric patients. MATERIALS AND METHODS: Thirty-three patients, 13 males and 20 females, with a mean age of 64.4 years were submitted to stimulated and unstimulated salivary flow rate and salivary pH measurements, and sense of taste evaluation. Tests were performed 3 months before complete denture substitution and 3 weeks after denture insertion. RESULTS: The mean for unstimulated saliva (USS) was 2.1 ml before and 2.7 ml after replacement (p = 0.003). The mean volume of stimulated saliva was 6.3 ml before and 8.2 ml after replacement (p = 0.004). The pH mean of USS was 7.8 ± 0.44 before and 8.02 ± 0.41 after replacement (p = 0.005). No statistically significant difference was determined in the sense of taste before and 3 weeks after complete denture replacement. CONCLUSIONS: The replacement of inadequate complete dentures increases saliva flow; however, it does not improve taste perception.

Computer-aided design finite element modeling of different approaches to rehabilitate endodontically treated teeth.

BACKGROUND: Carious lesions and dental fractures cause weakening in the dental structure. In these situations, endodontic treatment and prosthetic rehabilitation using an intraradicular post are indicated. However, the postspace preparation of the root canal further weakens the dental remnant, especially if there is no ferrule present. This study aimed to evaluate the stress distribution in endodontically treated upper premolars treated with different rehabilitation approaches. MATERIALS AND METHODS: An endodontically treated first upper premolar was modeled for finite element analysis. Three different approaches were carried out on this model: rehabilitation with fiberglass post (FCP), endocrown (ECW), or buildup. The models were exported in STEP format to the analysis software (ANSYS 17.2, ANSYS Inc., Houston, TX, USA). The solids were considered isotropic, homogeneous, and linearly elastic. A mechanical, structural static analysis was used as the criterion of maximum principal stress to show regions under tensile stress to evaluate the stress distribution in the restoration, cementation line, and root. A load of 400 N (90°) was applied to the lingual triangular ridge. The values of maximum principal stress in MPa were evaluated through colorimetric graphs. RESULTS: Similar stress concentration was observed for all groups. However, the ECW group presented higher values in the restoration/cement interface and root dentin. CONCLUSIONS: All the treatment modalities had favorable mechanical behavior to support the masticatory loads; nevertheless, the ECW group presented a higher risk of detachment failure.

Finite element analysis of the influence of geometry and design of zirconia crowns on stress distribution.

PURPOSE: To evaluate the influence of the geometry and design of prosthetic crown preparations on stress distribution in compression tests, using finite element analysis (FEA). MATERIALS AND METHODS: Six combinations of 3D drawings of all-ceramic crowns (yttria-stabilized zirconia framework and porcelain veneer) were evaluated: F, flat preparation and simplified crown; FC, flat preparation and crown with contact point; FCM, flat preparation and modified crown; A, anatomical preparation and simplified anatomical crown framework; AC, anatomical preparation and crown with contact point; and ACM, anatomical preparation and modified crown. Bonded contact types at all interfaces with the mesh were assigned, and the material properties used were according to the literature. A 200 N vertical load was applied at the center of each model. The maximum principal stresses were quantitatively and qualitatively analyzed. RESULTS: The highest values of tensile stress were observed at the interface between the ceramics in the region under the load application for the simplified models (F and A). Reductions in stress values were observed for the model with the anatomical preparation and modified infrastructure (ACM). The stress distribution in the flat models was similar to that of their respective anatomical models. CONCLUSIONS: The modified design of the zirconia coping reduces the stress concentration at the interface with the veneer ceramic, and the simplified preparation can exert a stress distribution similar to that of the anatomical preparation at and near the load point, when load is applied to the center of the crown.