RESUMEN
Mine tailings exposed to water and oxygen generate acid mine drainage (AMD) when the neutralizing minerals are insufficient to buffer the acid produced by sulfide oxidation. Mineral reactivity, such as sulfide oxidation and carbonate dissolution, leads to several changes within mine tailings in terms of their physical, mineralogical, and geochemical properties, which may lead to the release of metal(oid)s (e.g., As, Cu, Zn, Fe, S) into the environment. Fresh and oxidized tailings were sampled at two vertical profiles in a tailings storage facility (TSF). The TSF contains tailings from gold ore processing at a mine that has been closed for more than 25 years. Oxidized tailings have formed by in-situ oxidation of fresh tailings over more than 20 years. The collected samples were analyzed for: i) chemical composition by inductively coupled plasma atomic emission spectroscopy (ICP-AES), X-ray fluorescence (XRF), and total S/C; and ii) mineralogical composition by X-ray diffraction (XRD), Mineral Liberation Analyzer (MLA), Mossbauer spectroscopy, and Fe L-edge X-ray absorption near-edge spectroscopy (XANES). Mineralogically, the fresh tailings included more than 22 wt% carbonates and more than 10 wt% sulfides. In contrast, the oxidized tailings were composed mainly of secondary minerals such as iron oxy-hydroxides and gypsum. Geochemically, the fresh tailings exhibited a circumneutral behavior during weathering cell experiments and contaminants such as As were negligibly released (<0.3 mg/L). The latter is explained by formation of secondary iron oxy-hydroxides, which are known for the capacity to uptake several contaminants from the leachate. Long term oxidation of fresh tailings will lead to highly oxidized tailings similar to those collected in situ. The oxidized tailings exhibited an acidic behavior despite sulfide depletion due to latent acidity. The geochemical behavior was strongly controlled by the reactivity of secondary minerals (e.g., dissolution of gypsum and iron oxy-hydroxides). Quantitatively, the oxidized tailings released 163 mg/kg Fe, around 12,000 mg/kg S, and around 6 mg/kg Zn.
RESUMEN
Millions of tons of contaminated sediments are dredged each year from the main harbors in France. When removed from water, these sediments are very reactive, therefore their geochemical behavior must be understood in order to avoid dispersion of contaminated lixiviates in the surrounding soils. In this objective, it is necessary to evaluate the principal physicochemical parameters, and also achieve advanced mineralogical characterization. These studied sediments are highly contaminated by metals, notably copper (1445 and 835mg/kg, in the unweathered and naturally-weathered sediments, respectively), lead (760 and 1260mg/kg, respectively), zinc (2085 and 2550mg/kg, respectively), as well as by organic contaminants (PAH, PCB) and organometallics (organotins). A high concentration of sulfide minerals was also observed both in the unweathered sediment preserved under water (3.4wt% of pyrite especially), and in the naturally weathered sediment (2wt% pyrite), and in particular framboïdal pyrite was observed in the two materials. The presence of reactive mineral species in the naturally-weathered sediment can be explained by the deposit of a protective layer, composed of sulfide and their oxidation products (sulfate and iron oxides), thus preventing oxygen from diffusing through to the sulfide minerals. Additionally, the presence of aluminosilicates aggregates coating the sulfide minerals could also explain their presence in the naturally-weathered sediment. As organic matter is one of the principal constituents of the sediments (5.8 and 6.3wt% total organic carbon in the unweathered and weathered sediment, respectively), the aggregates are probably partially constituted of refractory humic material. It therefore appears that the natural weathering has led to a significant decrease in PAHs and organotins, but not in PCBs. The evolution of the granulometric structure and the distribution of the metallic contaminants could therefore lead us to consider a treatment by size separation, and a possible valorization of the dredged sediments in civil engineering.
RESUMEN
Predicting the water quality at mine sites is of significant importance for developing mines with respect for the environment. Acid mine drainage (AMD) occurs when sulfides are in contact with oxygen and water, and several parameters and mechanisms influence final drainage quality. Galvanic interactions influence the reactivity of sulfide minerals, which act as semi-conductors. These galvanic interactions have been insufficiently studied in the context of AMD generation. In this study, the influence of pyrite on the reactivity of sphalerite and chalcopyrite was investigated. Five blends, comprised of free grains of quartz/pyrite, quartz/chalcopyrite, quartz/sphalerite, quartz/pyrite/chalcopyrite, and quartz/pyrite/sphalerite, were subjected to geochemical testing. Five weathering cells were monitored over a 200-day period during which they were leached twice weekly. Leachates were analyzed for pH, Eh, electrical conductivity, and sulfate and metal concentrations. The results of these analyses showed that galvanic interactions occurred between free sulfide grains. Pyrite was galvanically protected over the full testing period in the quartz/pyrite/chalcopyrite blend, and partially protected in the quartz/pyrite/sphalerite blend. Moreover, the release of Cu from chalcopyrite and Zn, Mn, and Cd from sphalerite was accelerated in the presence of pyrite. This work provides a better understanding of the influence of pyrite on chalcopyrite and sphalerite reactivity by highlighting the galvanic effects. In the future, to improve the reliability of AMD prediction tests, galvanic interactions should be considered in both the prediction of the acid generation potential and the estimation of metal and metalloid release rates.
Asunto(s)
Electroquímica/métodos , Hierro/química , Sulfuros/química , Ácidos/química , Cobre/análisis , Contaminantes Ambientales/química , Concentración de Iones de Hidrógeno , Cinética , Microscopía Electrónica de Rastreo , Minerales/análisis , Minería , Oxidación-Reducción , Cuarzo , Reproducibilidad de los Resultados , Sulfatos/análisis , Azufre/química , Compuestos de Zinc/químicaRESUMEN
Mine wastes from sulfide-bearing ore extraction and processing are often stored at the surface of mine sites and could generate mine drainage. Prediction tests are completed to predict the water quality associated with the deposition of mining wastes. Static tests can quickly assess the acid-generating potential (AP) and the neutralization potential (NP). Whereas some studies recommend to take into account a mineral reactivity factor for the NP determination, the reactivity rates of acidifying minerals are not considered in the AP calculation. The aim of this study is to bring contribution to the improvement of the static test determination by adding kinetic factors in the AP determination. Eight sulfides (pyrite, Ni-pyrite, pyrrhotite, Ni-pyrrhotite, chalcopyrite, galena, sphalerite, arsenopyrite) and a sulfosalt (gersdorffite) were separately submitted to kinetic tests in modified weathering cells. This test was selected for its rapidity of results and for the low amount of material used, as it is somewhat difficult to obtain pure minerals samples. Five synthetic tailings were composed by mixing pure sulfides in various proportions and submitted to the same kinetic tests. The oxidation rates of synthetic tailings were compared with the weighted combined oxidation rates of individual pure sulfides. The oxidation rates of the synthetic tailings calculated from those of pure sulfides are within the same order of magnitude than those obtained through the kinetic experiments. The AP of synthetic tailings were calculated according to standard equations of the literature and compared with the new method.
Asunto(s)
Ácidos/análisis , Minería , Modelos Químicos , Aguas Residuales/química , Calidad del Agua , Monitoreo del Ambiente/métodos , Cinética , Oxidación-Reducción , Sulfuros/análisis , Sulfuros/químicaRESUMEN
Municipal Solid Waste Incineration (MSWI) Bottom Ash (BA) is a potential alternative adsorbent for biogas treatment due to its reactivity with hydrogen sulfide (H2S). The quality of BA depends however on the nature of the waste and the process technology of the waste incineration facility. To determine whether the origin of the BA could have an influence on its H2S elimination efficiency, comparative experimental tests were conducted in a landfill site with six bottom ashes from different MSW incinerators. Results showed that one of the BAs (A) had a much higher adsorption capacity than the rest (B-F), with 37g H2S/kg dry BA, compared to 11-16g H2S/kg dry BA for the other bottom ashes. Detailed physico-chemical analyses of the six BA were performed and complemented by principal component analysis to understand the different behaviors. BA iron content and specific surface area provided by the quench product stood out as key factors that promote the elimination of H2S.
Asunto(s)
Contaminantes Atmosféricos/análisis , Sulfuro de Hidrógeno/análisis , Incineración/métodos , Residuos Sólidos , Instalaciones de Eliminación de ResiduosRESUMEN
PURPOSE: Dredging of sediments, a requirement for harbor maintenance, removes millions of tons of mineral wastes, contaminated at varying degrees with trace metals, from the water. In previous investigations, Cu and Zn have been identified as highly concentrated trace metals associated to sulfides, mineral phases sensitive to oxidation. In order to ensure their sustainable management, the solidification/stabilization (S/S) and/or the valorization of contaminated sediments as secondary raw materials is a way to be promoted. Indeed, their reuse as a substitute of sand in cemented mortar formulation would allow combining both treatment and valorization of such wastes. METHODS: In the present study, the environmental assessment of mortars formulated with raw and weathered marine sediments (in particular contaminated with Cu, Pb and Zn), compared to sand reference mortars, was conducted through two kinetic leaching tests: weathering cell tests (WCTs), in which mortars were crushed and leached twice a week, and a tank monolith leaching test (MLT), in which leaching was performed on monolithic mortars with increasing leachate renewal time. RESULTS: In both leaching tests, calcium and sulfur were released continuously from sediment mortars, showing the oxidation-neutralization processes of sulfides and carbonates. In the MLT, Cu was released by sediment mortars through diffusion, particularly by weathered mortars, at low concentrations during 60 days of the test duration. With the more aggressive WCT, Cu concentrations were higher at the beginning but became negligible after 7 days of testing. Pb was released through diffusion mechanisms until depletion in both tests, whereas Zn was particularly well immobilized in the cemented matrices. CONCLUSIONS: The S/S process applied using hydraulic binders proved to be efficient in the stabilization of Cu, Pb, and Zn highly presents in studied sediments, and further valorization in civilian engineering applications could be considered.
Asunto(s)
Sedimentos Geológicos/análisis , Oxidación-Reducción , Sulfuros/análisis , Oligoelementos/análisisRESUMEN
Contaminated dredged sediments are often considered hazardous wastes, so they have to be adequately managed to avoid leaching of pollutants. The mobility of inorganic contaminants is a major concern. Metal sulfides (mainly framboïdal pyrite, copper, and zinc sulfides) have been investigated in this study as an important reactive metal-bearing phase sensitive to atmospheric oxygen action. An oxygen consumption test (OC-Test) has been adapted to assess the reactivity of dredged sediments when exposed to atmospheric oxygen. An experimental column set-up has been developed allowing the coupling between leaching and oxygen consumption test to investigate the reactivity of the sediment. This reactivity, which consisted of sulfide oxidation, was found to occur for saturation degree between 60 and 90 % and until the 20th testing week, through significant sulfates releases. These latter were assumed to come from sulfide oxidation in the first step of the test, then probably from gypsum dissolution. Confrontation results of OC-Test and leachate quality shows that Cu was well correlated to sulfates releases, which in turn, leads to Ca and Mg dissolution (buffer effect). Cu, and mostly Zn, was associated to organic matter, phyllosilicates, and other minerals through organo-clay complexes. This research confirmed that the OC-Test, originally developed for mine tailings, could be a useful tool in the dredged sediment field which can allow for intrinsic characterization of reactivity of a material suspected to readily reacting with oxygen and for better understanding of geochemical processes that affect pollutants behavior, conversion, and transfer in the environment.
Asunto(s)
Sedimentos Geológicos/química , Metales/química , Oxígeno/química , Sulfuros/química , Contaminantes Químicos del Agua/químicaRESUMEN
The tools developed for acid mine drainage (AMD) prediction were proven unsuccessful to predict the geochemical behavior of mine waste rocks having a significant chemical sorption capacity, which delays the onset of contaminated neutral drainage (CND). The present work was performed in order to test a new approach of water quality prediction, by using a chelating agent solution (0.03 M EDTA, or ethylenediaminetetraacetic acid) in kinetic testing used for the prediction of the geochemical behavior of geologic material. The hypothesis underlying the proposed approach is that the EDTA solution should chelate the metals as soon as they are released by sulfide oxidation, inhibiting their sorption or secondary precipitation, and therefore reproduce a worst-case scenario where very low metal attenuation mechanisms are present in the drainage waters. Fresh and weathered waste rocks from the Lac Tio mine (Rio tinto, Iron and Titanium), which are known to generate Ni-CND at the field scale, were submitted to small-scale humidity cells in control tests (using deionized water) and using an EDTA solution. Results show that EDTA effectively prevents the metals to be sorbed or to precipitate as secondary minerals, therefore enabling to bypass the delay associated with metal sorption in the prediction of water quality from these materials. This work shows that the use of a chelating agent solution is a promising novel approach of water quality prediction and provides general guidelines to be used in further studies, which will help both practitioners and regulators to plan more efficient management and disposal strategies of mine wastes.
Asunto(s)
Quelantes/química , Ácido Edético/química , Restauración y Remediación Ambiental/métodos , Metales/análisis , Minerales/análisis , Contaminantes Químicos del Agua/química , Contaminación Química del Agua/prevención & control , Cinética , Minería , QuebecRESUMEN
The underground extraction of Pb-Zn mineralization in the Touiref area stopped in 1958. A large volume of flotation tailings (more than 500 Mt) containing sulfides were deposited in a tailings impoundment. The goals of this study are to evaluate the neutralization capacity of the unoxidized and oxidized tailings, to assess the speciation of metals between the different components of the tailings material, and to assess the mobility of metals and the secondary minerals' precipitation in pore waters using geochemical modeling. To accomplish these objectives, representative samples from both fresh and oxidized zones were collected along a vertical profile through the tailings pile. Physical, chemical (ICP-MS), and mineralogical characterization (X-ray diffraction (XRD), reflected light microscopy, scanning electron microscope (SEM)) of these samples was performed. Grain size analysis shows that the tailings are dominated by silt- to sand-sized fractions. The microscopic observation highlights the presence of pyrite, marcasite, galena, and sphalerite as primary minerals in a carbonated matrix. The study reveals also the presence of secondary minerals represented by cerussite, smithsonite, anglesite, and Fe oxi-hydroxides as important scavengers for trace elements. The static tests show that the presence of calcite in the tailing samples ensures acid-neutralizing capacity (ANC), which is significantly greater than the acidity potential (PA). The geochemical characterization of the unoxidized samples shows higher Cd, Pb, and Zn concentrations than the oxidized samples containing the highest values for Fe and SO4. Sequential extraction tests show that significant percentages of metals are distributed between the acid-soluble fractions (Cd, Pb, and Zn) and the reducible one (Zn). Pore water analysis indicates that Ca is the dominant cation (8,170 and 6,200 mg L(-1), respectively), whereas sulfate is the principal anion (6,900 and 5,100 mg L(-1), respectively). Saturation index (SI) calculations of minerals in pore water extracted from both the oxidized and unoxidized samples are indicative of gypsum (SI >0) and Fe(III) oxides (SI â«0) precipitation. The latter controls the Fe concentration in solution.
Asunto(s)
Contaminantes Ambientales/análisis , Residuos Industriales/análisis , Metales/análisis , Minerales/análisis , Sulfatos/análisis , Sulfuros/análisis , Monitoreo del Ambiente , Minería , Modelos Teóricos , Túnez , Difracción de Rayos XRESUMEN
The environmental assessment of potential effects of contaminated harbor sediments stabilized with hydraulic binders and the determination of remediation endpoints require the determination of pollutants leaching potentials. Moreover, little information about the speciation and mobility of inorganic contaminants in these specific solid matrices is available in the literature. The objective of this paper is to investigate the relationship between mineralogy and leachability of contaminants (copper, lead, and zinc) present in a French harbor sediment stabilized with quicklime and Portland cement. Batch equilibrium leaching tests at various pH, chemical analysis of leachates, and mineralogical studies (X-ray diffraction, scanning electron microscopy-energy dispersive spectroscopy, and diffuse reflectance infrared Fourier transform) have been combined in the present investigation. The acid neutralization capacity of the stabilized matrix studied is first controlled by the dissolution of portlandite (pH ~12), followed by the dissolution of C-S-H (pH ~11) and the dissolution of ettringite (pH ~10). Finally, a very high buffering capacity of this stabilized sediment is observed for pH values around 6. This equilibrium is mainly controlled by the dissolution of iron sulfides and carbonate minerals. Consequently, the mobilization of inorganic contaminants as a function of pH remains very low (<0.1 wt%) for pH values above 6 and significantly increases for pH below these values. This research confirms the importance of a combined methodology for the intrinsic characterization of potential mobilization of contaminants in a stabilized sediment and for a better understanding of geochemical processes that affect contaminant fate, transformation, and transport in the subsurface environment.