Determination of Cleavage Energy and Efficient Nanostructuring of Layered Materials by Atomic Force Microscopy.

A method is presented to use atomic force microscopy to measure the cleavage energy of van der Waals materials and similar quasi-two-dimensional materials. The cleavage energy of graphite is measured to be 0.36 J/m2, in good agreement with literature data. The same method yields a cleavage energy of 0.6 J/m2 for MoS2 as a representative of the dichalcogenides. In the case of the weak topological insulator Bi14Rh3I9 no cleavage energy is obtained, although cleavage is successful with an adapted approach. The cleavage energies of these materials are evaluated by means of density-functional calculations and literature data. This further validates the presented method and sets an upper limit of about 0.7 J/m2 to the cleavage energy that can be measured by the present setup. In addition, this method can be used as a tool for manipulating exfoliated flakes, prior to or after contacting, which may open a new route for the fabrication of nanostructures.

Charge Trapping and Defect Dynamics as Origin of Memory Effects in Metal Halide Perovskite Memlumors.

Large language models for artificial intelligence applications require energy-efficient computing. Neuromorphic photonics has the potential to reach significantly lower energy consumption in comparison with classical electronics. A recently proposed memlumor device uses photoluminescence output that carries information about its excitation history via the excited state dynamics of the material. Solution-processed metal halide perovskites can be used as efficient memlumors. We show that trapping of photogenerated charge carriers modulated by photoinduced dynamics of the trapping states themselves explains the memory response of perovskite memlumors on time scales from nanoseconds to minutes. The memlumor concept shifts the paradigm of the detrimental role of charge traps and their dynamics in metal halide perovskite semiconductors by enabling new applications based on these trap states. The appropriate control of defect dynamics in perovskites allows these materials to enter the field of energy-efficient photonic neuromorphic computing, which we illustrate by proposing several possible realizations of such systems.

Electrical Doping of Metal Halide Perovskites by Co-Evaporation and Application in PN Junctions.

Electrical doping of semiconductors is a revolutionary development that enabled many electronic and optoelectronic technologies. While doping of many inorganic and organic semiconductors is well-established, controlled electrical doping of metal halide perovskites (MHPs) is yet to be demonstrated. In this work, efficient n- and p-type electrical doping of MHPs by co-evaporating the perovskite precursors alongside organic dopant molecules is achieved. It is demonstrated that the Fermi level can be shifted by up to 500 meV toward the conduction band and by up to 400 meV toward the valence band by n- and p-doping, respectively, which increases the conductivity of the films. The doped layers are employed in PN and NP diodes, showing opposing trends in rectification. Demonstrating controlled electrical doping by a scalable, industrially relevant deposition method opens the route to developing perovskite devices beyond solar cells, such as thermoelectrics or complementary logic.

Directional Amplified Photoluminescence through Large-Area Perovskite-Based Metasurfaces.

Perovskite nanocrystals are high-performance, solution-processed materials with a high photoluminescence quantum yield. Due to these exceptional properties, perovskites can serve as building blocks for metasurfaces and are of broad interest for photonic applications. Here, we use a simple grating configuration to direct and amplify the perovskite nanocrystals' original omnidirectional emission. Thus far, controlling these radiation properties was only possible over small areas and at a high expense, including the risks of material degradation. Using a soft lithographic printing process, we can now reliably structure perovskite nanocrystals from the organic solution into light-emitting metasurfaces with high contrast on a large area. We demonstrate the 13-fold amplified directional radiation with an angle-resolved Fourier spectroscopy, which is the highest observed amplification factor for the perovskite-based metasurfaces. Our self-assembly process allows for scalable fabrication of gratings with predefined periodicities and tunable optical properties. We further show the influence of solution concentration on structural geometry. By increasing the perovskite concentration 10-fold, we can produce waveguide structures with a grating coupler in one printing process. We analyze our approach with numerical modeling, considering the physiochemical properties to obtain the desired geometry. This strategy makes the tunable radiative properties of such perovskite-based metasurfaces usable for nonlinear light-emitting devices and directional light sources.

Towards low-temperature processing of efficient γ-CsPbI3 perovskite solar cells.

Inorganic cesium lead iodide (CsPbI3) perovskite solar cells (PSCs) have attracted enormous attention due to their excellent thermal stability and optical bandgap (∼1.73 eV), well-suited for tandem device applications. However, achieving high-performance photovoltaic devices processed at low temperatures is still challenging. Here we reported a new method for the fabrication of high-efficiency and stable γ-CsPbI3 PSCs at lower temperatures than was previously possible by introducing the long-chain organic cation salt ethane-1,2-diammonium iodide (EDAI2) and regulating the content of lead acetate (Pb(OAc)2) in the perovskite precursor solution. We find that EDAI2 acts as an intermediate that can promote the formation of γ-CsPbI3, while excess Pb(OAc)2 can further stabilize the γ-phase of CsPbI3 perovskite. Consequently, improved crystallinity and morphology and reduced carrier recombination are observed in the CsPbI3 films fabricated by the new method. By optimizing the hole transport layer of CsPbI3 inverted architecture solar cells, we demonstrate efficiencies of up to 16.6%, surpassing previous reports examining γ-CsPbI3 in inverted PSCs. Notably, the encapsulated solar cells maintain 97% of their initial efficiency at room temperature and under dim light for 25 days, demonstrating the synergistic effect of EDAI2 and Pb(OAc)2 in stabilizing γ-CsPbI3 PSCs.