Atmospheric Carbon Capture Performance of Legacy Iron and Steel Waste.

Legacy iron (Fe) and steel wastes have been identified as a significant source of silicate minerals, which can undergo carbonation reactions and thus sequester carbon dioxide (CO2). In reactor experiments, i.e., at elevated temperatures, pressures, or CO2 concentrations, these wastes have high silicate to carbonate conversion rates. However, what is less understood is whether a more "passive" approach to carbonation can work, i.e., whether a traditional slag emplacement method (heaped and then buried) promotes or hinders CO2 sequestration. In this paper, the results of characterization of material retrieved from a first of its kind drilling program on a historical blast furnace slag heap at Consett, U.K., are reported. The mineralogy of the slag material was near uniform, consisting mainly of melilite group minerals with only minor amounts of carbonate minerals detected. Further analysis established that total carbon levels were on average only 0.4% while average calcium (Ca) levels exceeded 30%. It was calculated that only ∼3% of the CO2 sequestration potential of the >30 Mt slag heap has been utilized. It is suggested that limited water and gas interaction and the mineralogy and particle size of the slag are the main factors that have hindered carbonation reactions in the slag heap.

Origin and Fate of Vanadium in the Hazeltine Creek Catchment following the 2014 Mount Polley Mine Tailings Spill in British Columbia, Canada.

Results from the analysis of aqueous and solid-phase V speciation within samples collected from the Hazeltine Creek catchment affected by the August 2014 Mount Polley mine tailings dam failure in British Columbia, Canada, are presented. Electron microprobe and X-ray absorption near-edge structure (XANES) analysis found that V is present as V3+ substituted into magnetite and V3+ and V4+ substituted into titanite, both of which occur in the spilled Mount Polley tailings. Secondary Fe oxyhydroxides forming in inflow waters and on creek beds have V K-edge XANES spectra exhibiting E1/2 positions and pre-edge features consistent with the presence of V5+ species, suggesting sorption of this species on these secondary phases. PHREEQC modeling suggests that the stream waters mostly contain V5+ and the inflow and pore waters contain a mixture of V3+ and V5+. These data, and stream, inflow, and pore water chemical data, suggest that dissolution of V(III)-bearing magnetite, V(III)- and V(IV)-bearing titanite, V(V)-bearing Fe(-Al-Si-Mn) oxhydroxides, and V-bearing Al(OH)3 and/or clay minerals may have occurred. In the circumneutral pH environment of Hazeltine Creek, elevated V concentrations are likely naturally attenuated by formation of V(V)-bearing secondary Fe oxyhydroxide, Al(OH)3, or clay mineral colloids, suggesting that the V is not bioavailable. A conceptual model describing the origin and fate of V in Hazeltine Creek that is applicable to other river systems is presented.

Sustained Bauxite Residue Rehabilitation with Gypsum and Organic Matter 16 years after Initial Treatment.

Bauxite residue is a high volume byproduct of alumina manufacture which is commonly disposed of in purpose-built bauxite residue disposal areas (BRDAs). Natural waters interacting with bauxite residue are characteristically highly alkaline, and have elevated concentrations of Na, Al, and other trace metals. Rehabilitation of BRDAs is therefore often costly and resource/infrastructure intensive. Data is presented from three neighboring plots of bauxite residue that was deposited 20 years ago. One plot was amended 16 years ago with process sand, organic matter, gypsum, and seeded (fully treated), another plot was amended 16 years ago with process sand, organic matter, and seeded (partially treated), and a third plot was left untreated. These surface treatments lower alkalinity and salinity, and thus produce a substrate more suitable for biological colonisation from seeding. The reduction of pH leads to much lower Al, V, and As mobility in the actively treated residue and the beneficial effects of treatment extend passively 20-30 cm below the depth of the original amendment. These positive rehabilitation effects are maintained after 2 decades due to the presence of an active and resilient biological community. This treatment may provide a lower cost solution to BRDA end of use closure plans and orphaned BRDA rehabilitation.

Mechanism of Vanadium Leaching during Surface Weathering of Basic Oxygen Furnace Steel Slag Blocks: A Microfocus X-ray Absorption Spectroscopy and Electron Microscopy Study.

Basic oxygen furnace (BOF) steelmaking slag is enriched in potentially toxic V which may become mobilized in high pH leachate during weathering. BOF slag was weathered under aerated and air-excluded conditions for 6 months prior to SEM/EDS and µXANES analysis to determine V host phases and speciation in both primary and secondary phases. Leached blocks show development of an altered region in which free lime and dicalcium silicate phases were absent and Ca-Si-H was precipitated (CaCO3 was also present under aerated conditions). µXANES analyses show that V was released to solution as V(V) during dicalcium silicate dissolution and some V was incorporated into neo-formed Ca-Si-H. Higher V concentrations were observed in leachate under aerated conditions than in the air-excluded leaching experiment. Aqueous V concentrations were controlled by Ca3(VO4)2 solubility, which demonstrate an inverse relationship between Ca and V concentrations. Under air-excluded conditions Ca concentrations were controlled by dicalcium silicate dissolution and Ca-Si-H precipitation, leading to relatively high Ca and correspondingly low V concentrations. Formation of CaCO3 under aerated conditions provided a sink for aqueous Ca, allowing higher V concentrations limited by kinetic dissolution rates of dicalcium silicate. Thus, V release may be slowed by the precipitation of secondary phases in the altered region, improving the prospects for slag reuse.

Removal and recovery of vanadium from alkaline steel slag leachates with anion exchange resins.

Leachable vanadium (V) from steel production residues poses a potential environmental hazard due to its mobility and toxicity under the highly alkaline pH conditions that characterise these leachates. This work aims to test the efficiency of anion exchange resins for vanadium removal and recovery from steel slag leachates at a representative average pH of 11.5. Kinetic studies were performed to understand the vanadium sorption process. The sorption kinetics were consistent with a pseudo-first order kinetic model. The isotherm data cannot differentiate between the Langmuir and Freundlich models. The maximum adsorption capacity (Langmuir value qmax) was 27 mg V g-1 resin. In column anion exchange, breakthrough was only 14% of the influent concentration after passing 90 L of steel slag leachate with 2 mg L-1 V through the column. When eluting the column 57-72% of vanadium was recovered from the resin with 2 M NaOH. Trials on the reuse of the anion exchange resin showed it could be reused 20 times without loss of efficacy, and on average 69% of V was recovered during regeneration. The results document for the first time the use of anion exchange resins to remove vanadium from steel slag leachate. As an environmental contaminant, removal of V from leachates may be an obligation for long-term management requirements of steel slag repositories. Vanadium removal coupled with the recovery can potentially be used to offset long-term legacy treatment costs.

EXAFS Study of Sr sorption to Illite, Goethite, Chlorite, and Mixed Sediment under Hyperalkaline Conditions.

Strontium is an important contaminant radionuclide at many former nuclear sites. This paper investigates the effect of changing pH and ionic strength on the sorption of Sr to a range of common soil minerals. Specifically it focuses on the sorption of Sr onto illite, chlorite, goethite, and a mixed sediment. The interplay between ionic strength and pH was determined by varying the background ionic strength of the system using both NaCl (for a constant pH) and NaOH (to also vary pH). Under conditions of moderate pH, Sr sorption decreased with increasing ionic strength, due to competition between the Na and Sr atoms for the outer-sphere complexes. However, where increasing ionic strength was accompanied by increasing pH, Sr sorption remained high. This suggested that Sr was sorbed to the minerals without competition from background Na ions. Extended X-ray absorption fine structure (EXAFS) spectra confirmed that at highly alkaline pH (>12.5) Sr was forming inner-sphere complexes on the surfaces of all minerals. This specific adsorption of the Sr (as SrOH(+)) explains why it was still adsorbed to the minerals under very high ionic strength conditions and was not out-competed by Na.

Use of bauxite residue (red mud) as a low cost sorbent for sulfide removal in polluted water remediation.

Sulfide is an important pollutant in aqueous systems. Sulfide removal from polluted waters is required prior to discharge. Red mud (RM) is a solid waste of bauxite processing that is rich in reactive iron oxides and consequently has the potential to be used to remove sulfide from aqueous systems. A series of experiments was undertaken using raw and sintered RM to remove sulfide from waters. RM was highly efficient at sulfide removal (average 75% sulfide removal at initial concentration of ∼5 mg L(-1), with 500 mg L(-1) RM addition) due to both physical adsorption (high specific area) and chemical reaction (with amorphous Fe). Sintered RM, which has a lower surface area and lower mineral reactivity, was much less efficient at removing sulfide (∼20% removal under equivalent experimental conditions). Furthermore, concomitant metal release from raw RM was lower than for sintered RM during the sulfide removal process. The results showed that raw RM is a potentially suitable material for sulfide removal from polluted waters and consequently could be used as a low cost alternative treatment in certain engineering applications.

Impact of the Diamond Light Source on research in Earth and environmental sciences: current work and future perspectives.

Diamond Light Source Ltd celebrated its 10th anniversary as a company in December 2012 and has now accepted user experiments for over 5 years. This paper describes the current facilities available at Diamond and future developments that enhance its capacities with respect to the Earth and environmental sciences. A review of relevant research conducted at Diamond thus far is provided. This highlights how synchrotron-based studies have brought about important advances in our understanding of the fundamental parameters controlling highly complex mineral-fluid-microbe interface reactions in the natural environment. This new knowledge not only enhances our understanding of global biogeochemical processes, but also provides the opportunity for interventions to be designed for environmental remediation and beneficial use.

Extracellular electron transport-mediated Fe(III) reduction by a community of alkaliphilic bacteria that use flavins as electron shuttles.

The biochemical and molecular mechanisms used by alkaliphilic bacterial communities to reduce metals in the environment are currently unknown. We demonstrate that an alkaliphilic (pH > 9) consortium dominated by Tissierella, Clostridium, and Alkaliphilus spp. is capable of using iron (Fe(3+)) as a final electron acceptor under anaerobic conditions. Iron reduction is associated with the production of a freely diffusible species that, upon rudimentary purification and subsequent spectroscopic, high-performance liquid chromatography, and electrochemical analysis, has been identified as a flavin species displaying properties indistinguishable from those of riboflavin. Due to the link between iron reduction and the onset of flavin production, it is likely that riboflavin has an import role in extracellular metal reduction by this alkaliphilic community.

Immobilization of chromate in hyperalkaline waste streams by green rusts and zero-valent iron.

Zero-valent iron (ZVI) and green rusts can be used as reductants to convert chromium from soluble, highly toxic Cr(VI) to insoluble Cr(III). This study compared the reduction rates of Cr(VI) by ZVI and two carbonate green rust phases in alkaline/hyperalkaline solutions. Batch experiments were carried out with synthetic chromate solutions at pH 7.7-12.3 and a chromite ore processing residue (COPR) leachate (pH approximately 12.2). Green rust removes chromate from high pH solutions (pH 10-12.5) very rapidly (<400 s). Chromate reduction rates for both green rust phases were consistently higher than for ZVI throughout the pH range studied; the surface area normalized rate constants were two orders of magnitude higher in the COPR leachate solution at pH 12.2. The performances of both green rusts were unaffected by changes in pH. In contrast, ZVI exhibited a marked decline in reduction rate with increasing pH to become almost ineffective above pH12.

Evolution of Cu and Zn speciation in agricultural soil amended by digested sludge over time and repeated crop growth.

Metals such as Zn and Cu present in sewage sludge applied to agricultural land can accumulate in soils and potentially mobilise into crops. Sequential extractions and X-ray absorption spectroscopy results are presented that show the speciation changes of Cu and Zn sorbed to anaerobic digestion sludge after mixing with soils over three consecutive 6-week cropping cycles, with and without spring barley (Hordeum vulgare). Cu and Zn in digested sewage sludge are primarily in metal sulphide phases formed during anaerobic digestion. When Cu and Zn spiked sludge was mixed with the soil, about 40% of Cu(I)-S phases and all Zn(II)-S phases in the amended sludge were converted to other phases (mainly Cu(I)-O and outer sphere Zn(II)-O phases). Further transformations occurred over time, and with crop growth. After 18 weeks of crop growth, about 60% of Cu added as Cu(I)-S phases was converted to other phases, with an increase in organo-Cu(II) phases. As a result, Cu and Zn extractability in the sludge-amended soil decreased with time and crop growth. Over 18 weeks, the proportions of Cu and Zn in the exchangeable fraction decreased from 36% and 70%, respectively, in freshly amended soil, to 28% and 59% without crop growth, and to 24% and 53% with crop growth. Overall, while sewage sludge application to land will probably increase the overall metal concentrations, metal bioavailability tends to reduce over time. Therefore, safety assessments for sludge application in agriculture should be based on both metal concentrations present and their specific binding strength within the amended soil.

Reuse potential of municipal solid waste incinerator bottom ash as secondary aggregate: Material characteristics, persistent organic pollutant content and effects of pH and selected environmental lixiviants on leaching behaviour.

Increasing municipal solid waste (MSW) production poses challenges for sustainable urban development. Modern energy-from-waste (EfW) facilities incinerate MSW, reducing mass and recovering energy. In the UK, MSW incineration bottom ash (MSW IBA) is primarily reused in civil engineering applications. This study characterizes UK-produced MSW IBA, examining its pH-dependent leaching behaviour and response to environmental lixiviants. Results show predominant components include a melt phase, primary glass and fine ash aggregations, and a chemical composition dominated by SiO2 (30-50 %), CaO (∼15 %), Fe2O3 (∼10 %), and Al2O3 (∼8%). X-ray absorption near edge structure (XANES) analysis shows that Zn and Cu are most likely oxygen-bound (adsorbed to oxy-hydroxides and as oxides) with some sulphur bound. Polychlorinated biphenyls (PCBs) and polychlorinated dibenzodioxins/furans (PCDD/Fs) are well below regulatory limits, and polycyclic aromatic hydrocarbons (PAHs) were undetectable. Leaching tests indicate trace elements mobilize at pHs ≤ 6. With a natural pH of 11.3 and high buffering capacity, significant acid inputs to the MSW IBA are required to reach this pH, which are improbable in the environment. Wood chip additions increase leachate's dissolved organic carbon (DOC) and reduce pH, but had minimal impact on metal-leaching behaviour. Synthetic plant exudate solutions minimally affect metal leaching at realistic concentrations, only enhancing leaching at ≥ 1500 mg l-1 DOC. This work supports MSW IBA's low-risk in specified civil engineering applications.

Metagenomes from microbial populations beneath a chromium waste tip give insight into the mechanism of Cr (VI) reduction.

Dumped Chromium Ore Processing Residue (COPR) at legacy sites poses a threat to health through leaching of toxic Cr(VI) into groundwater. Previous work implicates microbial activity in reducing Cr(VI) to less mobile and toxic Cr(III), but the mechanism has not been explored. To address this question a combined metagenomic and geochemical study was undertaken. Soil samples from below the COPR waste were used to establish anaerobic microcosms which were challenged with Cr(VI), with or without acetate as an electron donor, and incubated for 70 days. Cr was rapidly reduced in both systems, which also reduced nitrate, nitrite then sulfate, but this sequence was accelerated in the acetate amended microcosms. 16S rRNA gene sequencing revealed that the original soil sample was diverse but both microcosm systems became less diverse by the end of the experiment. A high proportion of 16S rRNA gene reads and metagenome-assembled genomes (MAGs) with high completeness could not be taxonomically classified, highlighting the distinctiveness of these alkaline Cr impacted systems. Examination of the coding capacity revealed widespread capability for metal tolerance and Fe uptake and storage, and both populations possessed metabolic capability to degrade a wide range of organic molecules. The relative abundance of genes for fatty acid degradation was 4× higher in the unamended compared to the acetate amended system, whereas the capacity for dissimilatory sulfate metabolism was 3× higher in the acetate amended system. We demonstrate that naturally occurring in situ bacterial populations have the metabolic capability to couple acetate oxidation to sequential reduction of electron acceptors which can reduce Cr(VI) to less mobile and toxic Cr(III), and that microbially produced sulfide may be important in reductive precipitation of chromate. This capability could be harnessed to create a Cr(VI) trap-zone beneath COPR tips without the need to disturb the waste.

Effect of grain size variation on strontium sorption to heterogeneous aquifer sediments.

Strontium-90 (90Sr) is a major contaminant at nuclear legacy sites. The mobility of 90Sr is primarily governed by sorption reactions with sediments controlled by high surface area phases such as clay and iron oxides. Sr2+ adsorption was investigated in heterogeneous unconsolidated aquifer sediments, analogous to those underlying the UK Sellafield nuclear site, with grainsizes ranging from gravels to clays. Batch sorption tests showed that a linear Kd adsorption model was applicable to all grainsize fractions up to equilibrium [Sr] of 0.28 mmol L-1. Sr2+ sorption values (Kd; Langmuir qmax) correlated well with bulk sediment properties such as cation exchange capacity and surface area. Electron microscopy showed that heterogeneous sediments contained porous sandstone clasts with clay minerals (i.e. chlorite) providing an additional adsorption capacity. Therefore, gravel corrections that assumed that the > 2 mm fractions are inert were not appropriate and underestimated Kd(bulk) adsorption coefficients. However, Kd (<2 mm) values measured from sieved sediment fractions, were effectively adjusted to within error of Kd (bulk) using a surface area dependant gravel correction based on particle size distribution data. Amphoteric pH dependent Sr2+ sorption behaviour observed in batch experiments was consistent with cation exchange modelling between pH 2-7 derived from the measured cation exchange capacities. Above pH 7 model fits were improved by invoking a coupled cation exchange/surface complexation which allowed for addition sorption to iron oxide phases. The overall trends in Sr2+ sorption (at pH 6.5-7) produced by increasing solution ionic strength was also reproduced in cation exchange models. Overall, the results showed that Sr2+ sorption to heterogeneous sediment units could be estimated from Kd (<2 mm) data using appropriate gravel corrections, and effectively modelled using coupled cation exchange and surface complexation processes.

Environmental behaviour of iron and steel slags in coastal settings.

Iron and steel slags have a long history of both disposal and beneficial use in the coastal zone. Despite the large volumes of slag deposited, comprehensive assessments of potential risks associated with metal(loid) leaching from iron and steel by-products are rare for coastal systems. This study provides a national-scale overview of the 14 known slag deposits in the coastal environment of Great Britain (those within 100 m of the mean high-water mark), comprising geochemical characterisation and leaching test data (using both low and high ionic strength waters) to assess potential leaching risks. The seaward facing length of slag deposits totalled at least 76 km, and are predominantly composed of blast furnace (iron-making) slags from the early to mid-20th Century. Some of these form tidal barriers and formal coastal defence structures, but larger deposits are associated with historical coastal disposal in many former areas of iron and steel production, notably the Cumbrian coast of England. Slag deposits are dominated by melilite phases (e.g. gehlenite), with evidence of secondary mineral formation (e.g. gypsum, calcite) indicative of weathering. Leaching tests typically show lower element (e.g. Ba, V, Cr, Fe) release under seawater leaching scenarios compared to deionised water, largely ascribable to the pH buffering provided by the former. Only Mn and Mo showed elevated leaching concentrations in seawater treatments, though at modest levels (<3 mg/L and 0.01 mg/L, respectively). No significant leaching of potentially ecotoxic elements such as Cr and V (mean leachate concentrations <0.006 mg/L for both) were apparent in seawater, which micro-X-Ray Absorption Near Edge Structure (µXANES) analysis show are both present in slags in low valence (and low toxicity) forms. Although there may be physical hazards posed by extensive erosion of deposits in high-energy coastlines, the data suggest seawater leaching of coastal iron and steel slags in the UK is likely to pose minimal environmental risk.

Alteration of sediments by hyperalkaline K-rich cement leachate: implications for strontium adsorption and incorporation.

Results are presented from 1 year batch experiments where K-rich hyperalkaline pH 13.5 young cement water (YCW) was reacted with sediments to investigate the effect of high pH, mineral alteration, and secondary mineral precipitation on (90)Sr sorption. After reaction with YCW, Sr sorption was found to be greater than 75% in all samples up to 365 days and 98% in a sample reacted for 365 days at 70 °C. Scanning electron microscopy analysis of sediment samples reacted at room temperature showed surface alteration and precipitation of a secondary phase, likely a K-rich aluminosilicate gel. The presence of Sr-Si(Al) bond distances in Sr K-edge extended X-ray absorption fine structure (EXAFS) analysis suggested that the Sr was present as an inner-sphere adsorption complex. However, sequential extractions found the majority of this Sr was still exchangeable with Mg(2+) at pH 7. For the sample reacted for 1 year at 70 °C, EXAFS analysis revealed clear evidence for ∼6 Sr-Si(Al) backscatters at 3.45 Å, consistent with Sr incorporation into the neoformed K-chabazite phase that was detected by X-ray diffraction and electron microscopy. Once incorporated into chabazite, (90)Sr was not exchangeable with Mg(2+), and chemical leaching with pH 1.5 HNO3 was required to remobilize 60% of the (90)Sr. These results indicate that, in high pH cementitious leachate, there is significantly enhanced Sr retention in sediments due to changes in the adsorption mechanism and incorporation into secondary silicate minerals. This suggests that Sr retention may be enhanced in this high pH zone and that the incorporation process may lead to irreversible exchange of the contaminant over extended time periods.

Behavior of aluminum, arsenic, and vanadium during the neutralization of red mud leachate by HCl, gypsum, or seawater.

Red mud leachate (pH 13) collected from Ajka, Hungary is neutralized to < pH 10 by HCl, gypsum, or seawater addition. During acid neutralization >99% Al is removed from solution during the formation of an amorphous boehmite-like precipitate and dawsonite. Minor amounts of As (24%) are also removed from solution via surface adsorption of As onto the Al oxyhydroxides. Gypsum addition to red mud leachate results in the precipitation of calcite, both in experiments and in field samples recovered from rivers treated with gypsum after the October 2010 red mud spill. Calcite precipitation results in 86% Al and 81% As removal from solution, and both are nonexchangeable with 0.1 mol L(-1) phosphate solution. Contrary to As associated with neoformed Al oxyhydroxides, EXAFS analysis of the calcite precipitates revealed only isolated arsenate tetrahedra with no evidence for surface adsorption or incorporation into the calcite structure, possibly as a result of very rapid As scavenging by the calcite precipitate. Seawater neutralization also resulted in carbonate precipitation, with >99% Al and 74% As removed from solution during the formation of a poorly ordered hydrotalcite phase and via surface adsorption to the neoformed precipitates, respectively. Half the bound As could be remobilized by phosphate addition, indicating that As was weakly bound, possibly in the hydrotalcite interlayer. Only 5-16% V was removed from solution during neutralization, demonstrating a lack of interaction with any of the neoformed precipitates. High V concentrations are therefore likely to be an intractable problem during the treatment of red mud leachates.

Gypsum addition to soils contaminated by red mud: implications for aluminium, arsenic, molybdenum and vanadium solubility.

Red mud is highly alkaline (pH 13), saline and can contain elevated concentrations of several potentially toxic elements (e.g. Al, As, Mo and V). Release of up to 1 million m(3) of bauxite residue (red mud) suspension from the Ajka repository, western Hungary, caused large-scale contamination of downstream rivers and floodplains. There is now concern about the potential leaching of toxic metal(loid)s from the red mud as some have enhanced solubility at high pH. This study investigated the impact of red mud addition to three different Hungarian soils with respect to trace element solubility and soil geochemistry. The effectiveness of gypsum amendment for the rehabilitation of red mud-contaminated soils was also examined. Red mud addition to soils caused a pH increase, proportional to red mud addition, of up to 4 pH units (e.g. pH 7 â†’ 11). Increasing red mud addition also led to significant increases in salinity, dissolved organic carbon and aqueous trace element concentrations. However, the response was highly soil specific and one of the soils tested buffered pH to around pH 8.5 even with the highest red mud loading tested (33 % w/w); experiments using this soil also had much lower aqueous Al, As and V concentrations. Gypsum addition to soil/red mud mixtures, even at relatively low concentrations (1 % w/w), was sufficient to buffer experimental pH to 7.5-8.5. This effect was attributed to the reaction of Ca(2+) supplied by the gypsum with OH(-) and carbonate from the red mud to precipitate calcite. The lowered pH enhanced trace element sorption and largely inhibited the release of Al, As and V. Mo concentrations, however, were largely unaffected by gypsum induced pH buffering due to the greater solubility of Mo (as molybdate) at circumneutral pH. Gypsum addition also leads to significantly higher porewater salinities, and column experiments demonstrated that this increase in total dissolved solids persisted even after 25 pore volume replacements. Gypsum addition could therefore provide a cheaper alternative to recovery (dig and dump) for the treatment of red mud-affected soils. The observed inhibition of trace metal release within red mud-affected soils was relatively insensitive to either the percentage of red mud or gypsum present, making the treatment easy to apply. However, there is risk that over-application of gypsum could lead to detrimental long-term increases in soil salinity.

Speciation of arsenic, chromium, and vanadium in red mud samples from the Ajka spill site, Hungary.

Results are presented from X-ray absorption spectroscopy based analysis of As, Cr, and V speciation within samples of bauxite ore processing residue (red mud) collected from the spill site at Ajka, Western Hungary. Cr K-edge XANES analysis found that Cr is present as Cr(3+) substituted into hematite, consistent with TEM analysis. V K-edge XANES spectra have E(1/2) position and pre-edge features consistent with the presence of V(5+) species, possibly associated with Ca-aluminosilicate phases. As K-edge XANES spectra identified As present as As(5+). EXAFS analysis reveals arsenate phases in red mud samples. When alkaline leachate from the spill site is neutralized with HCl, 94% As and 71% V are removed from solution during the formation of amorphous Al-oxyhydroxide. EXAFS analysis of As in this precipitate reveals the presence of arsenate Al-oxyhydroxide surface complexes. These results suggest that in the circumneutral pH, oxic conditions found in the Torna and Upper Marcal catchments, incorporation and sorption, respectively, will restrict the environmental mobility of Cr and As. V is inefficiently removed from solution by neutralization, therefore, the red mud may act as a source of mobile V(5+) where the red mud deposits are not removed from affected land.