Subcutaneous Injection Site Pain of Formulation Matrices.

PURPOSE: The objective of this work was to systematically evaluate the effects of formulation composition on subcutaneous injection site pain (ISP) using matrices comprising of common pharmaceutical excipients. METHODS: Two randomized, blinded, crossover studies in healthy subjects were conducted at a single site, where subjects received 1 mL SC injections of the buffer matrices. ISP intensity was measured using a 100 mm visual analogue scale (VAS), which was then analyzed via heatmap, categorical grouping, subgroup analysis, and paired delta analysis. RESULTS: Buffer type, buffer concentration and tonicity agent showed a substantial impact on ISP. Citrate buffer demonstrated a higher ISP than acetate buffer or saline). The 20 mM citrate buffer was more painful than 10 or 5 mM citrate buffers. NaCl and propylene glycol were significantly more painful than sugar alcohols (mannitol, sucrose, trehalose or glycerol). Histidine buffers exhibited ISP in the descending order of 150 mM > 75 mM > 25 mM > 0 mM NaCl, while histidine buffers containing Arginine-HCl at 0, 50, or 150 mM all showed very low ISP. Histidine buffer at pH 6.5 showed a lower ISP than pH 5.7. CONCLUSIONS: This systematic study via orthogonal analyses demonstrated that subcutaneous ISP is significantly influenced by solution composition.

Considerations for the Use of Polysorbates in Biopharmaceuticals.

PURPOSE: Polysorbates are commonly added to protein formulations and serve an important function as stabilizers. This paper reviews recent literature detailing some of the issues seen with the use of polysorbate 80 and polysorbate 20 in protein formulations. Based on this knowledge, a development strategy is proposed that leads to a control strategy for polysorbates in protein formulations. METHODS: A consortium of Biopharmaceutical scientists working in the area of protein formulations, shared experiences with polysorbates as stabilizers in their formulations. RESULTS: Based on the authors experiences and recent published literature, a recommendation is put forth for a development strategy which will lead into the appropriate control strategy for these excipients. CONCLUSIONS: An appropriate control strategy may comprise one or more elements of raw material, in-process and manufacturing controls. Additionally, understanding the role, if any, polysorbates play during stability will require knowledge of the criticality of the excipient, based upon its impact on CQAs due to variations in concentration and degradation level.

Subvisible (2-100 µm) particle analysis during biotherapeutic drug product development: Part 2, experience with the application of subvisible particle analysis.

Measurement and characterization of subvisible particles (including proteinaceous and non-proteinaceous particulate matter) is an important aspect of the pharmaceutical development process for biotherapeutics. Health authorities have increased expectations for subvisible particle data beyond criteria specified in the pharmacopeia and covering a wider size range. In addition, subvisible particle data is being requested for samples exposed to various stress conditions and to support process/product changes. Consequently, subvisible particle analysis has expanded beyond routine testing of finished dosage forms using traditional compendial methods. Over the past decade, advances have been made in the detection and understanding of subvisible particle formation. This article presents industry case studies to illustrate the implementation of strategies for subvisible particle analysis as a characterization tool to assess the nature of the particulate matter and applications in drug product development, stability studies and post-marketing changes.

Intramodule pressure profiles and protein accumulation during tangential flow filtration.

Tangential flow filtration (TFF) through a 30 kDa nominal molecular weight cut-off (MWCO) ultrafiltration membrane is widely employed to concentrate purified monoclonal antibodies (mAbs) to levels required for their formulation into injectable biologics. While TFF has been used to remove casein from milk for cheese production for over 35 years, and in pharmaceutical manufacture of biotherapeutic proteins for 20 years, the rapid decline in filtration rate (i.e., flux) at high protein concentrations is a limitation that still needs to be addressed. This is particularly important for mAbs, many of which are 140-160 kDa immunoglobulin G (IgG) type proteins recovered at concentrations of 200 mg/mL or higher. This work reports the direct measurement of local transmembrane pressure drops and off-line confocal imaging of protein accumulation in stagnant regions on the surface of a 30 kDa regenerated cellulose membrane in a flat-sheet configuration widely used in manufacture of biotherapeutic proteins. These first-of-a-kind measurements using 150 kDa bovine IgG show that while axial pressure decreases by 58 psi across a process membrane cassette, the decrease in transmembrane pressure drop is constant at about 1.2 psi/cm along the 20.7 cm length of the membrane. Confocal laser scanning microscopy of the membrane surface at the completion of runs where retentate protein concentration exceeds 200 mg/mL, shows a 50 µm thick protein layer is uniformly deposited. The localized measurements made possible by the modified membrane system confirm the role of protein deposition on limiting ultrafiltration rate and indicate possible targets for improving membrane performance.

A simple method for the detection of insoluble aggregates in protein formulations.

Low levels of insoluble aggregates in protein formulations can sometimes only be detected by visual inspection. To overcome the subjectivity and other limitations associated with visual inspection, a microscopic technique based on filtration/staining was developed. This method is a simple modification of the microscopic method listed in USP for particulate matter analysis and it provides two major advantages over the original method. First, particles are easier to see because of the staining. Second, this method is specific to protein aggregates so that it avoids interferences from other nonproteinaceous particles. In addition, this method does not have any restrictions on the rheological or optical properties of the samples. This method can be a useful tool in protein formulation development as demonstrated by its application in the evaluation of monoclonal antibody formulations.

Subvisible (2-100 µm) Particle Analysis During Biotherapeutic Drug Product Development: Part 1, Considerations and Strategy.

Measurement and characterization of subvisible particles (defined here as those ranging in size from 2 to 100 µm), including proteinaceous and nonproteinaceous particles, is an important part of every stage of protein therapeutic development. The tools used and the ways in which the information generated is applied depends on the particular product development stage, the amount of material, and the time available for the analysis. In order to compare results across laboratories and products, it is important to harmonize nomenclature, experimental protocols, data analysis, and interpretation. In this manuscript on perspectives on subvisible particles in protein therapeutic drug products, we focus on the tools available for detection, characterization, and quantification of these species and the strategy around their application.