Calorimetric Heats of Intrusion of LiCl Aqueous Solutions in Hydrophobic MFI-Type Zeosil: Influence of the Concentration.

For the first time, we report calorimetric measurements of intrusion of aqueous LiCl solutions in a hydrophobic pure siliceous MFI zeolite (silicalite-1) under high pressure. Our results show that the intrusion heats are strongly dependent on the LiCl concentration. The intrusion process is endothermic for diluted solutions (molar H2O/LiCl = 12) as well as for water, but it becomes exothermic for a concentration close to saturation (molar H2O/LiCl = 4). Analysis of the data in the framework of wetting thermodynamics shows that besides surface wetting, other phenomena occur during intrusion, such as hydrogen-bond weakening and composition change. In all cases, water is preferentially intruded so that the intruded phase becomes more diluted than the bulk solution. In the case of the most diluted solution, only water molecules seemed to be intruded. Furthermore, silicalite-1 is shown to be very stable in the presence of LiCl solution, with no noticeable structural and textural modifications observed after intrusion.

Heterogeneous Photoredox Catalysis Based on Silica Mesoporous Material and Eosin Y: Impact of Material Support on Selectivity of Radical Cyclization.

Heterogenization of the photocatalyst appears to be a valuable solution to reach sustainable processes. Rapid and efficient synthesis of supported photocatalyst is still a remaining challenge and the choice of the support material is crucial. The present study aims at preparing a new generation of hybrid inorganic/organic photocatalysts based on silica mesoporous material and Eosin Y. These results highlight the influence of non-covalent interactions between the material support and the reagent impacting the selectivity of the reaction.

Synthesis of Hierarchical MOR-Type Zeolites with Improved Catalytic Properties.

Hierarchical MOR-type zeolites were synthesized in the presence of hexadecyltrimethylammonium bromide (CTAB) as a porogen agent. XRD proved that the concentration of CTAB in the synthesis medium plays an essential role in forming pure hierarchical MOR-type material. Above a CTAB concentration of 0.04 mol·L-1, amorphous materials are observed. These hierarchical mordenite possess a higher porous volume compared to its counterpart conventional micrometer crystals. Nitrogen sorption showed the presence of mesoporosity for all mordenite samples synthesized in the presence of CTAB. The creation of mesopores due to the presence of CTAB in the synthesis medium does not occur at the expense of zeolite micropores. In addition, mesoporous volume and BET surface seem to increase upon the increase of CTAB concentration in the synthesis medium. The Si/Al ratio of the zeolite framework can be increased from 5.5 to 9.1 by halving the aluminum content present in the synthesis gel. These synthesized hierarchical MOR-type zeolites possess an improved catalytic activity for n-hexane cracking compared to large zeolite crystals obtained in the absence of CTAB.

Hierarchical Zeolites as Catalysts for Biodiesel Production from Waste Frying Oils to Overcome Mass Transfer Limitations.

Hierarchical crystals with short diffusion path, conventional microcrystals and nanocrystals of ZSM-5 zeolites were used for biodiesel production from waste frying oils and were assessed for their catalytic activity in regard to their pore structure and acidic properties. Produced zeolites were characterized using XRD, nitrogen adsorption-desorption, SEM, TEM, X-ray fluorescence, and FTIR. Pore size effect on molecular diffusion limitation was assessed by Thiele modulus calculations and turnover frequencies (TOF) were used to discuss the correlation between acidic character and catalytic performance of the zeolites. Owing to the enhanced accessibility and mass transfer of triglycerides and free fatty acids to the elemental active zeolitic structure, the catalytic performance of nanosponge and nanosheet hierarchical zeolites was the highest. A maximum yield of 48.29% was reached for the transesterification of waste frying oils (WFOs) using HZSM-5 nanosheets at 12:1 methanol to WFOs molar ratio, 180 °C, 10 wt % catalyst loading, and 4 h reaction time. Although HZSM-5 nanosponges achieved high conversions, these more hydrophilic zeolites did not function according to their entire acidic strength in comparison to HZSM-5 nanosheets. NSh-HZSM5 catalytic performance was still high after 4 consecutive cycles as a result of the zeolite regeneration.

Zeolite-Polymer Composite Materials as Water Scavenger.

The influence of the charge compensating cation nature (Na+, Mg2+) on the water adsorption properties of LTA-type zeolites used as filler in composite materials (zeolite/polymers) was investigated. Large scale cation exchanges were performed on zeolite powder at 80 °C for 2 h using 1 M magnesium chloride (MgCl2) aqueous solutions. XRF, ICP, and EDX analyses indicate a successful cationic exchange process without the modification of the zeolite structure as shown by XRD and solid-state NMR analyses. Composite materials (granulates and molded parts) were manufactured using to extrusion and injection processes. In the case of MgA zeolite, nitrogen adsorption-desorption experiments allowed us to measure a microporous volume, unlike NaA zeolite, which is non-porous to nitrogen probe molecule. SEM and EDX analyses highlighted the homogeneous distribution of zeolite crystals into the polymer matrix. Water adsorption capacities confirmed that the trends observed in the zeolite powder samples are preserved after dragging zeolites into composite formulations. Granulates and molded parts composite samples containing the magnesium exchanged zeolite showed an increase of their water adsorption capacity up to +27% in comparison to composite samples containing the non-exchanged zeolite. The MgA composite is more promising for water decontamination applications due to its higher water adsorption properties than the NaA composite.

Offretite Zeolite Single Crystals Synthesized by Amphiphile-Templating Approach.

Offretite zeolite synthesis in the presence of cetyltrimethylammonium bromide (CTABr) is reported. The offretite crystals were synthesized with a high crystallinity and hexagonal prismatic shape after only 72 h of hydrothermal treatment at 180 °C. The CTABr has dual-functions during the crystallization of offretite, viz. as structure-directing agent and as mesoporogen. The resulting offretite crystals, with a Si/Al ratio of 4.1, possess more acid sites than the conventional offretite due to their high crystallinity and hierarchical structure. The synthesized offretite is also more reactive than its conventional counterpart in the acylation of 2-methylfuran for biofuel production under non-microwave instant heating condition, giving 83.5% conversion with 100% selectivity to the desired product 2-acetyl-5-methylfuran. Hence, this amphiphile synthesis approach offers another cost-effective and alternative route for crystallizing zeolite materials that require expensive organic templates.

Effect of zeolite morphology on charge separated states: ZSM-5-type nanocrystals, nanosheets and nanosponges.

In the present work, we investigate the electron transfer occurring in the porous void of three MFI-type zeolite (ZSM-5) nanomaterials (nanocrystals, nanosheets and nanosponges) after adsorption and photoexcitation of t-stilbene (t-St). ZSM-5 nanosheets are constituted of lamellar stacking of several nanosheets (20-40 nm) where each nanosheet has a thickness of 2 nm. Nanosponges are composed of ZSM-5 nanocrystals (2-3 nm) separated by mesoporous holes of 5.8 nm facilitating the synthesis of hierachical materials. While the nanosheets show microporosity similar to that observed for the ZSM-5 nanocrystals, the absorption isotherms of the nanosponges show the existence of secondary micropores. After photoirradiation of t-St, UV-vis absorption spectroscopy shows the formation of charge separated states (radical cation and charge transfer complex) in the nanocrystals and in the nanosheets whereas no ionized species is detected in the nanosponges. The radical cation (RC) is stabilized in the nanosheets while it evolves very rapidly towards a Charge Transfer Complex (CTC) in the nanocrocrystals. The particular morphology of the nanosheets and nanosponges is put forward to explain this result since all host materials are of the MFI-type. To investigate ultra-short phenomena in the three nanomaterials, the UV-vis transient spectra were recorded between 2 and 450 µs after photoexcitation by nanosecond laser pulses. In the nanocrystals and nanosheets only the RC is detected whereas CTC formation is not observed. Photoexcitation of t-St in the nanosponges also leads to the formation of a RC but it recombines completely within 70 µs. This suggests the preferential location of t-St in the secondary micropores with pores larger than the micropores of the MFI-type framework and possibly in the mesopores of the nanosponges.

Structural interpretation of the energetic performances of a pure silica LTA-type zeolite.

The high pressure intrusion-extrusion process of different electrolyte aqueous solutions (NaCl and CaCl2, 2 M and 3 M) in a hydrophobic pure-silica LTA zeolite was investigated for energetic purposes by means of in situ X-ray powder diffraction, porosimeter tests, thermogravimetric analysis and NMR spectroscopy. The intrusion pressure of the saline solutions was proved to be higher than that of pure water, with the highest value measured for CaCl2, thus increasing the energetic performance of the system. The intrusion of NaCl solutions was irreversible (bumper behavior), whereas that of CaCl2 solutions is partially reversible (shock absorber behavior). The structural investigation allowed interpreting these results on the basis of the different intrusion mechanisms, in turn induced by the different nature of the cations present in the electrolyte solutions. When Si-LTA is intruded by NaCl solution, firstly H2O molecules penetrate the pores, leading to higher silanol defect formation followed by the solvated ions. With CaCl2, instead, due to a higher solvation enthalpy of Ca2+, a higher pressure is required for intrusion, and both H2O and ions penetrate at the same pressure. The structural refinements demonstrate (i) a different arrangement of the extraframework species in the two systems, (ii) the intrusion of the salt solutions occurs through strong desolvation of the ions and (iii) the salt/H2O ratios of the intruded species are higher than those of the starting electrolyte solutions.

Energetic Performance of Pure Silica Zeolites under High-Pressure Intrusion of LiCl Aqueous Solutions: An Overview.

An overview of all the studies on high-pressure intrusion-extrusion of LiCl aqueous solutions in hydrophobic pure silica zeolites (zeosils) for absorption and storage of mechanical energy is presented. Operational principles of heterogeneous lyophobic systems and their possible applications in the domains of mechanical energy storage, absorption, and generation are described. The intrusion of LiCl aqueous solutions instead of water allows to considerably increase energetic performance of zeosil-based systems by a strong rise of intrusion pressure. The intrusion pressure increases with the salt concentration and depends considerably on zeosil framework. In the case of channel-type zeosils, it rises with the decrease of pore opening diameter, whereas for cage-type ones, no clear trend is observed. A relative increase of intrusion pressure in comparison with water is particularly strong for the zeosils with narrow pore openings. The use of highly concentrated LiCl aqueous solutions instead of water can lead to a change of system behavior. This effect seems to be related to a lower formation of silanol defects under intrusion of solvated ions and a weaker interaction of the ions with silanol groups of zeosil framework. The influence of zeosil nanostructure on LiCl aqueous solutions intrusion-extrusion is also discussed.

Synthesis of FAU-Type Zeolite Membranes with Antimicrobial Activity.

In this study, a layer of a pure and dense phase of FAU-type zeolite was synthesized directly on the surface of α-Al2O3 plane macroporous support. Before hydrothermal synthesis, a step of cleaning of the support by an anionic detergent was performed, a roughness surface is created, allowing the anchoring of the zeolite nuclei and then their growth, favoring in this sense the formation of a homogeneous zeolite layer. The obtained membranes were fully characterized using X-ray diffraction analysis (XRD), nitrogen sorption, scanning electron microscopy (SEM), and mercury porosimetry. After 24 h of thermal treatment at 75 °C, a homogeneous zeolite layer composed of bipyramidal crystals of FAU-type zeolite is obtained with a thickness of about 2.5 µm. No obvious defects or cracks can be observed. It was found that the increase in heating temperature could lead to the appearance of an impurity phase, GIS-type zeolite. Then the ideal zeolite membrane was exchanged with Ag+ or Zn2+ cations to studies their antimicrobial properties. Zeolites membranes exchanged with Ag+ showed an agar-diffusive bactericidal activity against gram negative Escherichia coli (E. coli) bacteria. Zn2+ exchanged zeolite membrane presented a bacteriostatic activity that is less diffusive in agar. As expected, non-exchanged zeolite membrane (in its Na+ form) have no effect on bacterial activity. This process is particularly interesting for the synthesis of a good quality FAU-type zeolite membranes with antimicrobial properties.

Efficient Removal of Volatile Organic Compounds by FAU-Type Zeolite Coatings.

Silicone and pure organic binders were used to develop FAU-type zeolite coatings applied on pre-treated aluminum substrates by using a spraying method and then cured under specific conditions. The influence of the amount of binder on adhesion properties of zeolite coatings was first investigated to determine the optimum ratio between zeolite and binder. Zeolite coatings were then elaborated with a high zeolite content (between 70 and 80 wt.%) to ensure high adsorption capacities. The amount of binders involved in different zeolite coatings was sufficient to achieve interesting adhesion and cohesion properties. The accessibility of zeolite microporosity was studied by nitrogen adsorption-desorption measurements, which revealed a very small or no loss of the micropore volume for the optimized coatings. Volatile Organic Compounds (VOCs) adsorption measurements were carried out using n-hexane as probe molecule. FAU-type zeolite in powder form adsorbs 180 mg/ganhydrous zeolite, whereas the amounts of n-hexane adsorbed by zeolite coatings ranged from 131 to 175 mg/ganhydrous zeolite.

Synthesis of Hierarchical Zeolites with Morphology Control: Plain and Hollow Spherical Beads of Silicalite-1 Nanosheets.

Binderless pure silica zeolites (zeosils) spheres and hollow spheres with a diameter of 20 µm composed of silicalite-1 nanosheets particles were prepared by pseudomorphic transformation of spherical silica beads using different temperatures (110, 130, and 150 °C) and treatment times (1-5 days) in order to adapt the local dissolution rate of silica to the crystallization rate of silicalite-1 nanosheets allowing to preserve the initial morphology of the silica beads. Fully crystalline beads of 20 µm were obtained at 110 °C for 5 days, whereas hollow spheres similar in size were synthesized at higher temperatures. The crystallization process seems to begin at the outer surface of the amorphous silica beads and spreads with the time in the interior of the beads leading to a dissolution of the inner amorphous part of the beads to create zeosil hollow spheres for the highest treatment temperatures (130 and 150 °C). The dissolution rate of the inner amorphous part of the beads increases by increasing the hydrothermal treatment temperature from 130 to 150 °C. The silicalite-1 beads synthesized at 110 °C for 5 days showed to be promising for rapid molecular decontamination by adsorbing n-hexane in larger amount than the silicalite-1 conventional big crystals in powder forms.

Influence of the Compensating Cation Nature on the Water Adsorption Properties of Zeolites.

The influence of the compensating cation (Na+, Li+, Mg2+) nature on the water adsorption properties of LTA and FAU-type zeolites was investigated. Cation exchanges were performed at 80 °C for 2 h using 1 M aqueous solutions of lithium chloride (LiCl) or magnesium chloride (MgCl2). XRF and ICP-OES analyses indicate that the cation exchange yields reach values between 59 to 89% depending on the number of exchange cycles and the nature of the zeolite and cation, while both zeolites structures are preserved during the process, as shown by XRD and solid state NMR analyses. Nitrogen adsorption-desorption experiments indicate a higher available microporous volume when sodium cations are replaced by smaller monovalent lithium cations or by divalent magnesium cations because twice less cations are needed compared to monovalent cations. Up to 15% of gain in the available microporous volume is obtained for FAU-type zeolites exchanged with magnesium cation. This improvement facilitates the adsorption of water with an increase in the water uptake up to 30% for the LTA and FAU type zeolites exchanged with magnesium. These exchanged zeolites are promising for uses in water decontamination because a smaller amount is needed to trap the same amount of water compared to their sodium counterparts.

Synthesis of Binderless ZK-4 Zeolite Microspheres at High Temperature.

Binderless zeolite macrostructures in the form of ZK-4 microspheres were prepared using anion-exchange resin beads as shape-directing macrotemplates. The particles were synthesized under hydrothermal conditions at different temperatures and treatment times. The influence of the different synthesis parameters was investigated by X-ray diffraction, scanning electron microscopy, fluorescence X, nitrogen adsorption measurements and 29Si solid-state NMR. Fully crystalline spheres similar in size and shape to the original resin beads were obtained by a hydrothermal treatment at the highest temperatures (150⁻180 °C) for a short treatment time of 24 h. The synthesized microspheres showed to be promising in the molecular decontamination of volatile organic compounds (VOCs).

Energetic behavior of the pure silica ITQ-12 (ITW) zeolite under high pressure water intrusion.

Experimental water intrusion-extrusion isotherms were obtained at room temperature on pure silica ITW-type zeolites (ITQ-12 zeosil). The water intrusion is obtained by applying a high hydraulic pressure corresponding to the intrusion step. When the pressure is released, the water extrusion occurs at a similar pressure to that of the intrusion one. Therefore, the "ITW zeosil-water" system behaves like a spring and the phenomenon is reproducible over several cycles. Several characterization techniques have been performed before and after water intrusion-extrusion experiments in order to reveal the presence or the lack of defects after such experiments. Structural modifications at the long range order cannot be observed by XRD analysis after three water intrusion-extrusion cycles. However, solid state NMR spectroscopy provides evidence of the presence of Q3 groups revealing the breaking of some siloxane bridges after the intrusion step. The "ITW zeosil-water" system can restore 100% of the stored energy corresponding to about 8 J g(-1).

Rational Design and Characterisation of Novel Mono- and Bimetallic Antibacterial Linde Type A Zeolite Materials.

The development of antimicrobial devices and surfaces requires the setup of suitable materials, able to store and release active principles. In this context, zeolites, which are microporous aluminosilicate minerals, hold great promise, since they are able to serve as a reservoir for metal-ions with antimicrobial properties. Here, we report on the preparation of Linde Type A zeolites, partially exchanged with combinations of metal-ions (Ag+, Cu2+, Zn2+) at different loadings (0.1-11.9 wt.%). We combine X-ray fluorescence, scanning electron microscopy, energy-dispersive X-ray spectroscopy, and X-ray diffraction to monitor the metal-ion contents, distribution, and conservation of the zeolite structure after exchange. Then, we evaluate their antimicrobial activity, using agar dilution and optical-density monitoring of Escherichia coli cultures. The results indicate that silver-loaded materials are at least 70-fold more active than the copper-, zinc-, and non-exchanged ones. Moreover, zeolites loaded with lower Ag+ concentrations remain active down to 0.1 wt.%, and their activities are directly proportional to the total Ag content. Sequential exchanges with two metal ions (Ag+ and either Cu2+, Zn2+) display synergetic or antagonist effects, depending on the quantity of the second metal. Altogether, this work shows that, by combining analytical and quantitative methods, it is possible to fine-tune the composition of bi-metal-exchanged zeolites, in order to maximise their antimicrobial potential, opening new ways for the development of next-generation composite zeolite-containing antimicrobial materials, with potential applications for the design of dental or bone implants, as well as biomedical devices and pharmaceutical products.

A Novel Numerical Procedure to Estimate the Electric Charge in the Pore from Filtration of Single-Salt Solutions.

The assessment of physicochemical parameters governing the transport of ions through nanoporous membranes is a major challenge due to the difficulty in experimental estimation of the dielectric constant of the solution confined in nanopores and the volumetric membrane charge. Numerical identification by adjusting their values to fit experimental data is a potential solution, but this method is complicated for single-salt solutions due to the infinite number of couples that can describe a rejection curve. In this study, a novel procedure based on physical simplifications which allows the estimation of a range of values for these two parameters is proposed. It is shown here that the evolution of the interval of membrane charge with salt concentration can be described in all the experimental conditions by the Langmuir-Freundlich hybrid adsorption isotherm. Finally, it is highlighted that considering the mean dielectric constant and the adsorption isotherms assessed from a range of concentrations allowed a good prediction of rejection curves, irrespective of the salt and membrane considered.

Deposition of NiO Nanoparticles on Nanosized Zeolite NaY for Production of Biofuel via Hydrogen-Free Deoxygenation.

Nickel-based catalysts play an important role in the hydrogen-free deoxygenation for the production of biofuel. The yield and quality of the biofuel are critically affected by the physicochemical properties of NiO supported on nanosized zeolite Y (Y65, crystal size of 65 nm). Therefore, 10 wt% NiO supported on Y65 synthesized by using impregnation (IM) and deposition-precipitation (DP) methods were investigated. It was found that preparation methods have a significant effect on the deoxygenation of triolein. The initial rate of the DP method (14.8 goil·h-1) was 1.5 times higher than that of the IM method (9.6 goil·h-1). The DP-Y65 showed the best deoxygenation performance with a 80.0% conversion and a diesel selectivity of 93.7% at 380 °C within 1 h. The outstanding performance from the DP method was due to the smaller NiO particle size (3.57 ± 0.40 nm), high accessibility (H.F value of 0.084), and a higher Brönsted to Lewis acidity (B/L) ratio (0.29), which has improved the accessibility and deoxygenation ability of the catalyst. The NH4+ released from the decomposition of the urea during the DP process increased the B/L ratio of zeolite NaY. As a result, the pretreatment to convert Na-zeolite to H-zeolite in a conventional zeolite synthesis can be avoided. In this regard, the DP method offers a one-pot synthesis to produce smaller NiO-supported nanosized zeolite NaY with a high B/L ratio, and it managed to produce a higher yield with selectivity towards green diesel via deoxygenation under a hydrogen-free condition.

Reminiscent capillarity in subnanopores.

Fluids in large and small pores display different behaviors with a crossover described through the concept of critical capillarity. Here we report experimental and simulation data for various siliceous zeolites and adsorbates that show unexpected reminiscent capillarity for such nanoporous materials. For pore sizes D exceeding the fluid molecule size, the filling pressures p are found to follow a generic behavior kBT ln p ∼ γ/ρD where γ and ρ are the fluid surface tension and density. This result is rationalized by showing that the filling chemical potential for such ultra-small pores is the sum of an adsorption energy and a capillary energy that remains meaningful even for severe confinements. A phenomenological model, based on Derjaguin's formalism to bridge macroscopic and molecular theories for condensation in porous materials, is developed to account for the behavior of fluids confined down to the molecular scale from simple parameters.

Performance of surfactant-modified *BEA-type zeolite nanosponges for the removal of nitrate in contaminated water: Effect of the external surface.

Hierarchical *BEA-type nanosponges zeolite with a high external surface area (116 m2.g-1) and small crystal size, synthesized in the presence of a dual-porogenic organic compound, were modified with a cationic surfactant (HDTMA+Br-: hexadecyltrimethyl ammonium bromide) in order to create a new anion exchanger system: the surfactant-modified zeolite nanosponges (SMZNS). For comparison, two other surfactant-modified *BEA-type zeolite materials, SMZMC and SMZNC, were obtained by modifying the synthesized conventional micron-size microcrytals and nanocrystals *BEA-type zeolite with HDTMA+Br-, respectively. Textural and structural properties were determined for the three prepared materials using N2 adsorption/desorption analysis, XRD, SEM, and TEM. Nitrate adsorption isotherms were drawn in a large concentration range [0.8-24.2 mmol.L-1] and fitted with Langmuir isotherm model. The maximum nitrate removal capacity (1338 mmol.Kg-1/83 mg.g-1) was obtained for SMZNS material. This value is the highest ever observed for nitrate removal using surfactant-modified zeolite. The nitrate removal kinetics were fitted with the pseudo second-order model for both materials SMZNS and SMZNC.