Organic LEDs Based on Bis(8-hydroxyquinoline) Zinc Derivatives with a Styryl Group.

For the first time, organic light-emitting diodes (OLEDs) based on bis(8-hydroxyquinoline) zinc with a styryl group (ZnStq) dispersed in poly(N-vinylcarbazole) matrix (ZnStq_R:PVK, where R = H, Cl, OCH3) were fabricated. The ZnStq_R:PVK films made via the spin-coating method were used as the active layer in these devices. The produced OLEDs showed strong electroluminescence with yellow emissions at 590, 587 and 578 nm for the ZnStq_H:PVK, ZnStq_Cl:PVK and ZnStq_OCH3:PVK, respectively. For all the studied thin films, the main photoluminescence emission bands were observed between 565 and 571 nm. The OLED with the ZnStq_OCH3:PVK layer with a narrow electroluminescence spectrum was found to have sufficient color purity to produce ultra-high-resolution displays with reduced power consumption (full width at half maximum of 59 nm, maximum brightness of 2244 cd/m2 and maximum current efficiency of 1.24 cd/A, with a turn-on voltage of 6.94 V and a threshold voltage of 7.35 V). To characterize the photophysical properties of the active layer, the ZnStq_R:PVK layers samples were additionally deposited on glass and silicon substrates. We found that the obtained results predestine ZnStq_R:PVK layers for use in the lighting industry in the future.

Influence of Heat Treatment on Surface, Structural and Optical Properties of Nickel and Copper Phthalocyanines Thin Films.

The work presents the effect of annealing on the change of polycrystalline α and ß phases of copper and nickel phthalocyanines. We have found that this process has a great influence on the optical properties of the vapor-deposited layers. The performed measurements showed that for various forms of MPc, the values of the refractive index and the extinction coefficient increased, and consequently, so did the absorption coefficient. The AFM images taken showed that the values before and after heating are morphologically different. Raman measurements showed that the band at about 1526 cm-1 (B1g symmetry) has higher intensity for the α form than for the ß form. The intensity of this band is related to changing the form of phthalocyanine from α to ß. Our measurements have shown that by changing the annealing temperature of the layers, we change their optical properties. As a consequence, we change their optoelectronic parameters, adjusting them to the requirements of new optoelectronic devices, such as solar cells, sensors, displays and OLEDs.

Effect of 2-Methylthiazole Group on Photoinduced Birefringence of Thiazole-Azo Dye Host-Guest Systems at Different Wavelengths of Irradiation.

The photoinduced birefringence behaviors of host-guest systems based on heterocyclic thiazole-azo dyes with different substituents, dispersed into PMMA matrix, were investigated under three excitation wavelengths, i.e., 405 nm, 445 nm or 532 nm. The wavelengths fell on the blue side, near the maximum or on the red side of the absorption bands of trans-azo dyes, respectively. We found that photoinduced birefringence was generated at a similar extent in all studied systems, except the system containing a 2-methyl-5-benzothiazolyl as thiazole-azo dye substituent. For this material, the achieved birefringence value was the highest among the whole series, regardless of the excitation wavelength. Moreover, we identified the optimal irradiation wavelength for efficient birefringence generation and showed that large absorption of excitation light by trans isomer does not account for achieving a significant degree of molecular alignment. The obtained results indicate that thiazole-azo dye with a 2-methyl-5-benzothiazolyl substituent shows promising photoinduced birefringence, and can be considered a dye potentially suitable for optical applications.

Physico-Chemical and Light-Induced Properties of Quinoline Azo-dyes Polymers.

We present investigation of optical and photochromic properties as well as of surface quality of thin films of novel methacrylic polymers with 8-hydroxyquinoline azo-dyes in side-chain. Additionally, thermal stability of polymer powders was examined and their glass transition temperature was determined. Optical properties (extinction coefficient and refractive index) were determined by spectroscopic ellipsometry (SE) combined with absorbance measurements. Photoresponsive behavior was investigated by determination of photoisomerization rates under irradiation with unpolarized 365 nm light, as well as by conduction of holographic grating inscription experiment. Thin film quality was determined by atomic force microscopy (AFM) measurements. Thermal analysis was performed by thermogravimetric (TG), derivative thermogravimetric (DTG) and differential scanning calorimetry (DSC) measurements. We found that optical properties as well as photoisomerization rates of investigated polymers are dependent on the substituent in the para position of the phenyl ring. Surface relief grating inscription was successfully generated only for materials with chromophores containing dimethylamino (N(CH3)2) and methyl (CH3) substituents, but all materials exhibited birefringence grating in the bulk. Surface of most thin films was very smooth, but its quality was impaired by neutral (H) as well as carboxyl (COOH) substituent. Thermal stability of copolymers with side-chain chromophores was improved compared to pure poly(methyl methacrylate) (PMMA).

Enhancement of third-order nonlinear optical susceptibility of Alq3 in polar aprotic solvents.

The influence of solvent polarity on nonlinear optical properties of tris-(8-hydroxyquinoline)-aluminum (Alq3) was investigated by the degenerate four-wave mixing method at the 532 nm. It was obtained that the effective values of the third-order nonlinear optical susceptibility (χeff⟨3⟩) and the second-order hyperpolarizability (γeff) of Alq3 depend on the solvent polarity. Additionally, it was found that Alq3 dissolved in dimethyl sulfoxide has the highest values of χeff⟨3⟩ and γeff. Furthermore, two Stegeman's figures of merit were also calculated. The obtained results suggest that Alq3 is also promising material for application in all-optical signal processing devices.

Influence of P3HT:PCBM Ratio on Thermal and Transport Properties of Bulk Heterojunction Solar Cells.

The influence of P3HT:PCBM ratio on thermal and transport properties of solar cells were determined by photothermal beam deflection spectrometry, which is advantageous tool for non-destructively study of bulk heterojunction layers of organic solar cells. P3HT:PCBM layers of different P3HT:PCBM ratios were deposited on top of PEDOT:PSS/ITO layers which were included in organic bulk-heterojunction solar cells. The thermal diffusivity, energy gap and charge carrier lifetime were measured at different illumination conditions and with a different P3HT:PCBM ratios. As expected, it was found that the energy band gap depends on the P3HT:PCBM ratio. Thermal diffusivity is decreasing, while charge carrier lifetime is increasing with PCBM concentration. Energy band gap was found to be independent on illumination intensity, while thermal diffusivity was increasing and carrier lifetime was decreasing with illumination intensity. The carrier lifetime exhibits qualitatively similar dependence on the PCBM concentration when compared to the open-circuit voltage of operating solar cells under AM1.5 illumination. BDS and standard I-V measurement yielded comparable results arguing that the former is suitable for characterization of organic solar cells.

Spectroscopic Studies of Styrylquinoline Copolymers with Different Substituents.

The aim of the study was to present the influence of various styrylquinoline (StQ) substituents on the luminescence, structural, and optical properties of StQ-containing copolymers. StQ-containing copolymers were synthesized by free-radical thermoinitiated polymerization. The calculations of the copolymerization ratios for the obtained copolymers were based on the basis of the integrated peak areas of the 1H NMR spectra in CDCl3. The luminescence measurements show that the change in the nature of the electron-donating and electron-withdrawing of the substituent shifts the emission band to longer wavelengths and causes a transition from blue fluorescence to green or yellow and orange (or even white), regardless of the electronic nature of the introduced substituent group. The structural properties were measured by Fourier-Transform Infrared (FTIR) and Raman spectroscopies. For all of the compounds, we observed similarities in the bands in FTIR and Raman measurements. The optical parameters were obtained from the absorbance measurements. Additionally, Scanning Electron Microscopy (SEM) was used to study the surface topography of the thin layers on the glass substrate. The SEM images confirm that we obtained smoother layers for two copolymers. The computational Density Functional Theory (DFT) analysis fully supports the beneficial features of the analyzed systems for their applications in optoelectronic devices. Based on the obtained results, it can be concluded that all of the studied styrylquinolines are promising materials for applications in organic light-emitting diodes (OLEDs). However, COP1 with an OCH3 donor substituent possess a wider luminescence band, and its layer is smoother and more transparent.

Influence of the Microstructure and Optical Constants on Plasmonic Properties of Copper Nanolayers.

Copper layers with thicknesses of 12, 25, and 35 nm were thermally evaporated on silicon substrates (Si(100)) with two different deposition rates 0.5 and 5.0 Å/s. The microstructure of produced coatings was studied using atomic force microscopy (AFM) and powder X-ray diffractometer (XRD). Ellipsometric measurements were used to determine the effective dielectric functions <ε˜> as well as the quality indicators of the localized surface plasmon (LSP) and the surface plasmon polariton (SPP). The composition and purity of the produced films were analysed using X-ray photoelectron spectroscopy (XPS).

Distance Effects of Phenylpiperazine-Containing Methacrylic Polymers on Optical and Structural Properties.

New materials based on methacrylic polymers modified with 1-(4-nitrophenyl)piperazine side chains, differing in the distance of the chromophore from the polymer main chain and/or the separation between the chromophoric units in the chain, are obtained and characterized in terms of their potential applications in optoelectronic devices. The surface, structural, and optical properties of the investigated materials are determined using atomic force microscopy, spectroscopic ellipsometry combined with transmission measurements, Raman and Fourier transform infrared spectroscopy, as well as cyclic voltammetry. The relevant model systems are additionally analyzed with quantum chemical density functional theory calculations in order to enable the generalization of the structure-photophysical property relationships for the optimization of the material features. It is found that the structural modification of the material, relying on the transit of the piperazine moiety away from the main polymer chain, leads to the hypsochromic shift of the absorption spectrum. Moreover, the lowest refractive index values are obtained for the polymer with a distant ethylene group in the side-chains and increased separation between the piperazine units. It was shown that the optical energy band gaps of the investigated piperazine-containing polymers are in the range from 2.73 to 2.81 eV, which reveals their promising potential for the advances in photovoltaics, field effect transistors, or electrochromic devices as an alternative for other widely applied polymer materials.

Synthesis, Optical, and Morphological Studies of ZnO Powders and Thin Films Fabricated by Wet Chemical Methods.

Zinc oxide nanoparticles were prepared from Zn5(CO3)2(OH)6 precursor, capped with poly(vinylpyrrolidone) (PVP), and annealed at 600 °C. The obtained powders were characterized by a powder X-ray diffraction (PXD), transmission electron microscopy (TEM), scanning electron microscopy (SEM), UV-visible spectroscopy (UV-vis), Raman spectroscopy, infrared spectroscopy (IR), thermal analysis (TGA/DTA), and third-order nonlinear (NL) optical measurement. Morphological evaluation by TEM and SEM measurements indicated that the precursor micro-particles are ball-shaped structures composed of plates with a thickness of approximately 10 nm. ZnO thin films, as well as ZnO/polymer multilayer layouts, were obtained by wet chemical methods (spin- and dip-coating). Surface topography and morphology of the obtained films were studied by SEM and AFM microscopy. Films with uniformly distributed ZnO plates, due to the erosion of primary micro-particles were formed. The fabricated specimens were also analyzed using a spectroscopic ellipsometry in order to calculate dielectric function and film thickness.