Structural analysis of the initial lithiation of NiO thin film electrodes.

Observations of the initial lithiation of NiO electrodes demonstrate how to seed conversion reactions using interfaces in a thin film Ni/NiO bilayer architecture. Operando X-ray reflectivity (XRR) reveals that structural changes in a NiO film begin at potentials near the theoretical reduction potential (1.8-2.0 V) with detectable lithiation of both the buried Ni/NiO interface and the outer NiO surface that occur prior to the reaction of the NiO film. This initial conversion reaction is most pronounced in ultrathin NiO films (∼20 Å) with only small changes to the NiO film surface for thicker films (∼67 Å). The limited reactivity of thicker NiO films probed using operando grazing incidence small-angle X-ray scattering (GISAXS) shows the growth of nanoparticles at the electrode/electrolyte interface during initial lithium ion insertion, with a 16-20 Å average radius. Ex situ X-ray photoelectron spectroscopy (XPS), time-of-flight secondary ion mass spectrometry (ToF-SIMS), and scanning transmission electron microscopy/electron energy loss spectroscopy (STEM/EELS) confirm our conclusions about the morphological changes accompanying initial stage of lithiation in these conversion reaction electrodes. The present study reveals the interconnected challenges of solid-solid transitions, overpotentials, interfacial nucleation and kinetics, and transition metal dissolution in conversion-type electrodes that are critical for their use as electrodes in lithium-ion batteries.

Sorting of Molecular Building Blocks from Solution to Surface.

We demonstrate that molecular gradients on an organic monolayer is formed by preferential binding of ruthenium complexes from solutions also containing equimolar amounts of isostructural osmium complexes. The monolayer consists of a nanometer-thick assembly of 1,3,5-tris(4-pyridylethenyl)benzene (TPEB) covalently attached to a silicon or metal-oxide surface. The molecular gradient of ruthenium and osmium complexes is orthogonal to the surface plane. This gradient propagates throughout the molecular assembly with thicknesses over 30 nm. Using other monolayers consisting of closely related organic molecules or metal complexes results in the formation of molecular assemblies having an homogeneous and equimolar distribution of ruthenium and osmium complexes. Spectroscopic and computational studies revealed that the geometry of the complexes and the electronic properties of their ligands are nearly identical. These subtle differences cause the isostructural osmium and ruthenium complexes to pack differently on modified surfaces as also demonstrated in crystals grown from solution. The different packing behavior, combined with the organic monolayer significantly contributes to the observed differences in chemical composition on the surface.

Lithiation of multilayer Ni/NiO electrodes: criticality of nickel layer thicknesses on conversion reaction kinetics.

X-ray reflectivity and transmission electron microscopy (TEM) were used to characterize the morphological changes in thin film electrodes with alternating Ni and NiO layers during lithiation as a function of the Ni buffer layer thickness. Complete lithiation of the active NiO layers occurs only when the thickness of the Ni/NiO bilayers are less than 75 Å - a threshold value that is determined by the sum of the Ni quantity in the Ni/NiO bilayer of the multilayer stack. Thicker Ni/NiO bilayers present a kinetic barrier for lithium ion diffusion inside the stack resulting in partial lithiation of the multilayer electrodes in which only the top NiO layer lithiates. Lithiation of NiO layers in a multilayer stack also leads to an interface-specific reaction that is observed to increase the thicknesses of adjacent Ni layers by 3-4 Å and is associated with the formation of a low-density Li2O layer, corresponding to an interfacially-driven phase separation of the NiO. Rate dependent cyclic voltammetry studies reveal a linear relation between the peak current and scan rate suggesting that the lithiation kinetics are controlled by charge transfer resistance at the liquid-solid interface.

Light-Induced Conversion of Chemical Permeability to Enhance Electron and Molecular Transfer in Nanoscale Assemblies.

In this paper, we demonstrate how photochemically enhancing the permeability of metal-organic assemblies results in a significant enhancement of the electrochemical activity of metal complexes located within the assembly. The molecular assemblies consist of different layers of redox-active metal complexes ([M(mbpy-py)3][PF6]2; M = Ru or Os) that are separated by redox-inactive spacers consisting of 1,4-bis[2-(4-pyridyl)ethenyl]benzene (BPEB) and PdCl2 of variable thicknesses (0-13.4 nm). UV-irradiation (λ = 254 nm) of our assemblies induces a photochemical reaction in the redox-inactive spacer increasing the permeability of the assembly. The observed increase was evident by trapping organic (nBu4NBF4) and inorganic (NiCl2) salts inside the assemblies, and by evaluating the electrochemical response of quinones absorbed inside the molecular assemblies before and after UV irradiation. The increase in permeability is reflected by higher currents and a change in the directionality of electron transfer, i.e., from mono- to bidirectional, between the redox-active metal complexes and the electrode surface. The supramolecular structure of the assemblies dominates the overall electron transfer properties and overrules possible electron transfer mediated by the extensive π-conjugation of its individual organic components.

Effect of solvent polarizability on the assembly and ordering of nanoscale polyhedral oligomeric silsesquioxane films.

Understanding the factors that affect molecular self-assembly is crucial to building designed nanoscale structures. We have deposited nanoscale films of polyhedral oligomeric silsesquioxane (POSS) onto polished silicon substrates from a range of organic solvents. We studied these films using synchrotron X-ray reflectivity and found that dip-coating from benzene, toluene, or chloroform results in near-substrate ordering only, but when acetone, hexane, or THF is used, self-assembled layers are formed throughout the entire deposited film. We conclude that solvent polarizability is the factor that determines the alignment of the POSS molecules. We have successfully tested this prediction using additional solvents selected on the basis of their calculated polarizabilities.

Composite molecular assemblies: nanoscale structural control and spectroelectrochemical diversity.

The controlled deposition of metal complexes from solution on inorganic surfaces offers access to functional materials that otherwise would be elusive. For such surface-confined interfaces to form, specific assembly sequences are often used. We show here that varying the assembly sequence of two well-defined and iso-structural osmium and ruthenium polypyridyl complexes results in interfaces with strikingly different spectroelectrochemical properties. Successive deposition of redox-active layers of osmium and ruthenium polypyridyl complexes, leads to self-propagating molecular assemblies (SPMAs) with distinct internal interfaces and individually addressable components. In contrast, the clear separation of these interfaces upon sequential deposition of these two complexes, results in charge trapping or electrochemical communication between the metal centers, as a function of layer thickness and applied assembly sequence. The SPMAs were characterized using a variety of techniques, including: UV­vis spectroscopy, spectroscopic ellipsometry, electrochemistry, synchrotron X-ray reflectivity, angle-resolved X-ray photoelectron spectroscopy, and spectroelectrochemistry. The combined data demonstrate that the sequence-dependent assembly is a decisive factor that influences and provides the material properties that are difficult to obtain otherwise.

Assembly of surface-confined homochiral helicates: chiral discrimination of DOPA and unidirectional charge transfer.

Surface-confined double-helical polymers are generated by dynamic covalent assembly with preservation of chirality, metal coordination environment, and oxidation state of the precursor complexes. This one-step procedure involves both in solution and solution-to-surface assembly and resulted in chiral interfaces where pairs of ligands are wrapped around arrays of metal ions. In-plane XRD experiments revealed the formation of a highly ordered structure along the substrate surface. The chirality of the surfaces is expressed by the selective recognition of 3,4-dihydroxyphenylalanine (DOPA). The CD measurements show a response of the Δ-polymer-modified quartz substrates toward D-DOPA, whereas no change was observed after treatment with L-DOPA. These coordination-based interfaces assembled on metal-oxide substrates in combination with a redox-probe, [Os(bpy)3](PF6)2, in solution can resemble the behavior of a rectifier.

Coordination-based molecular assemblies of oligofurans and oligothiophenes.

Molecular assemblies (MAs) of oligofurans and oligothiophenes were formed from solutions on various substrates. These films were obtained by alternating deposition of organic chromophores (oligofurans or oligothiophenes) and a palladium salt. These coordination-based MAs were characterized by UV/Vis spectroscopy, spectroscopic ellipsometry, atomic force microscopy (AFM), X-ray reflectivity (XRR), X-ray photoelectron spectroscopy (XPS), and electrochemistry. The MAs exhibit similar electrochemical behavior and their growth and structure are apparently not affected when different organic template layers are used. The density of the MAs is a function of the structure of the molecular component. The oligothiophene density is approximately 50% higher than that observed for the oligofuran-based assemblies. The optical and electrochemical properties of the MAs scale linearly with their thickness. The UV/Vis data indicate that upon increasing the film thickness, there is no significant conjugation between the metal-separated organic chromophores. DFT calculations confirmed that the HOMO-LUMO gap of the surface-bound oligofuran and oligothiophene metal oligomers do not change significantly upon increasing their chain length. However, electrochemical measurements indicate that the susceptibility of the MAs towards oxidation is dependent on the number of chromophore units.

Preparation and characterization of graphene oxide paper.

Free-standing paper-like or foil-like materials are an integral part of our technological society. Their uses include protective layers, chemical filters, components of electrical batteries or supercapacitors, adhesive layers, electronic or optoelectronic components, and molecular storage. Inorganic 'paper-like' materials based on nanoscale components such as exfoliated vermiculite or mica platelets have been intensively studied and commercialized as protective coatings, high-temperature binders, dielectric barriers and gas-impermeable membranes. Carbon-based flexible graphite foils composed of stacked platelets of expanded graphite have long been used in packing and gasketing applications because of their chemical resistivity against most media, superior sealability over a wide temperature range, and impermeability to fluids. The discovery of carbon nanotubes brought about bucky paper, which displays excellent mechanical and electrical properties that make it potentially suitable for fuel cell and structural composite applications. Here we report the preparation and characterization of graphene oxide paper, a free-standing carbon-based membrane material made by flow-directed assembly of individual graphene oxide sheets. This new material outperforms many other paper-like materials in stiffness and strength. Its combination of macroscopic flexibility and stiffness is a result of a unique interlocking-tile arrangement of the nanoscale graphene oxide sheets.

Enhanced LiMn2O4 Thin-Film Electrode Stability in Ionic Liquid Electrolyte: A Pathway to Suppress Mn Dissolution.

Spinel-type lithium manganese oxide (LiMn2O4) cathodes suffer from severe manganese dissolution in the electrolyte, compromising the cyclic stability of LMO-based Li-ion batteries (LIBs). In addition to causing structural and morphological deterioration to the cathode, dissolved Mn ions can migrate through the electrolyte to deposit on the anode, accelerating capacity fade. Here, we examine single-crystal epitaxial LiMn2O4 (111) thin-films using synchrotron in situ X-ray diffraction and reflectivity to study the structural and interfacial evolution during cycling. Cyclic voltammetry is performed in a wide range (2.5-4.3 V vs Li/Li+) to promote Mn3+ formation, which enhances dissolution, for two different electrolyte systems: an imidazolium ionic liquid containing lithium bis-(trifluoromethylsulfonyl)imide (LiTFSI) and a conventional carbonate liquid electrolyte containing lithium hexafluorophosphate (LiPF6). We find exceptional stability in this voltage range for the ionic liquid electrolyte compared to the conventional electrolyte, which is attributed to the absence of Mn dissolution in the ionic liquid. X-ray reflectivity shows a negligible loss of cathode material for the films cycled in the ionic liquid electrolyte, further confirmed by inductively coupled plasma mass spectrometry and transmission electron microscopy. Conversely, a substantial loss of Mn is found when the film is cycled in the conventional electrolyte. These findings show the significant advantages of ionic liquids in suppressing Mn dissolution in LiMn2O4 LIB cathodes.

Electrolyte Reactivity on the MgV2O4 Cathode Surface.

Predictive understanding of the molecular interaction of electrolyte ions and solvent molecules and their chemical reactivity on electrodes has been a major challenge but is essential for addressing instabilities and surface passivation that occur at the electrode-electrolyte interface of multivalent magnesium batteries. In this work, the isolated intrinsic reactivities of prominent chemical species present in magnesium bis(trifluoromethanesulfonimide) (Mg(TFSI)2) in diglyme (G2) electrolytes, including ionic (TFSI-, [Mg(TFSI)]+, [Mg(TFSI):G2]+, and [Mg(TFSI):2G2]+) as well as neutral molecules (G2) on a well-defined magnesium vanadate cathode (MgV2O4) surface, have been studied using a combination of first-principles calculations and multimodal spectroscopy analysis. Our calculations show that nonsolvated [Mg(TFSI)]+ is the strongest adsorbing species on the MgV2O4 surface compared with all other ions while partially solvated [Mg(TFSI):G2]+ is the most reactive species. The cleavage of C-S bonds in TFSI- to form CF3- is predicted to be the most desired pathway for all ionic species, which is followed by the cleavage of C-O bonds of G2 to yield CH3+ or OCH3- species. The strong stabilization and electron transfer between ionic electrolyte species and MgV2O4 is found to significantly favor these decomposition reactions on the surface compared with intrinsic gas-phase dissociation. Experimentally, we used state-of-the-art ion soft landing to selectively deposit mass-selected TFSI-, [Mg(TFSI):G2]+, and [Mg(TFSI):2G2]+ on a MgV2O4 thin film to form a well-defined electrolyte-MgV2O4 interface. Analysis of the soft-landed interface using X-ray photoelectron, X-ray absorption near-edge structure, electron energy-loss spectroscopies, as well as transmission electron microscopy confirmed the presence of decomposition species (e.g., MgFx, carbonates) and the higher amount of MgFx with [Mg(TFSI):G2]+ formed in the interfacial region, which corroborates the theoretical observation. Overall, these results indicate that Mg2+ desolvation results in electrolyte decomposition facilitated by surface adsorption, charge transfer, and the formation of passivating fluorides on the MgV2O4 cathode surface. This work provides the first evidence of the primary mechanisms leading to electrolyte decomposition at high-voltage oxide surfaces in multivalent batteries and suggests that the design of new, anodically stable electrolytes must target systems that facilitate cation desolvation.

Understanding the Solid-State Electrode-Electrolyte Interface of a Model System Using First-Principles Statistical Mechanics and Thin-Film X-ray Characterization.

Intermixing of atomic species at the electrode-electrolyte boundaries can impact the properties of the interfaces in solid-state batteries. Herein, this work uses first-principles statistical mechanics along with experimental characterization to understand intermixing at the electrode-electrolyte interface. For the model presented in this work, lithium manganese oxide (LiMn2O4, LMO) and lithium lanthanum titanate (Li3xLa2/3-xTiO3, LLTO) are employed as the cathode and electrolyte, respectively. The results of the computational work show that Ti-Mn intermixing at the interface is significant at synthesis temperatures. The experimental results in this work find that, at some critical temperatures between 600 and 700 °C for material preparation, the interface of LLTO-LMO becomes blurred. Calculations predict that the interface is unstable with regard to Ti-Mn intermixing starting at 0 K, suggesting that the critical temperature found in the experiment is related to kinetics. The work overall suggests that, in designing a solid-state battery, the fundamental reactions such as intermixing need to be considered.

Synergism in multicomponent self-propagating molecular assemblies.

Multicomponent self-propagating molecular assemblies (SPMAs) have been generated from an organic chromophore, a redox-active polypyridyl complex, and PdCl(2). The structure of the multicomponent SPMA is not a linear combination of two assemblies generated with a single molecular constituent. Surface-confined assemblies formed from only the organic chromophore and PdCl(2) are known to follow linear growth, whereas the combination of polypyridyl complexes and PdCl(2) results in exponential growth. The present study demonstrates that an iterative deposition of both molecular building blocks with PdCl(2) results in an exponentially growing assembly. The nature of the assembly mechanism is dictated by the polypyridyl complex and overrides the linear growth process of the organic component. Relatively smooth, multicomponent SPMAs have been obtained with a thickness of ∼20 nm on silicon, glass, and indium-tin oxide (ITO) coated glass. Detailed information of the structure and of the surface-assembly chemistry were obtained using transmission optical (UV/Vis) spectroscopy, ellipsometry, atomic force microscopy (AFM), synchrotron X-ray reflectivity (XRR), and electrochemistry.

Stepwise assembly of coordination-based metal-organic networks.

Metal-organic networks (MONs) were created by a stepwise solution deposition approach from vinylpyridine-based building blocks and PdCl(2). The combined experimental and computational study demonstrates the formation of saturated, structurally organized systems on solid supports. The rigid nature and geometry of the components are well-suited to form honeycomb and parallelogram structures, as predicted by a computational study. Detailed structural information of the new MONs was obtained by optical (UV/vis) spectroscopy, ellipsometry, atomic force microscopy (AFM), X-ray photoelectron spectroscopy (XPS), and synchrotron X-ray reflectivity (XRR). Notably, the XPS elemental composition indicates the formation of a palladium coordination-based network.

Control of thin liquid film morphology during solvent-assisted film deposition.

Liquid films of different silicate esters were deposited from volatile solvents on hydroxylated and hydrogen-passivated silicon surfaces. We show that adsorption of silicate ester molecules and the resulting structural morphology of the liquid films not only are determined by attractive van der Waals forces with contributions from electrostatic interactions between the silicone ester moieties and oxide surface sites but also can be tuned by modifying the substrate surface or by changing the liquid-solvent interactions. Our results also show the importance of the conformational properties of liquid molecules and their rearrangements at the liquid/solid interface for controlled solvent-assisted film deposition.

Structural signal of a dynamic glass transition.

Pentaphenyl trimethyl trisiloxane is an isotropic liquid at room temperature with a dynamic glass transition at 224 K. Using x-ray reflectivity, we see surface density oscillations (layers) develop below 285 K, similar to those seen in other metallic and dielectric liquids and in computer simulations. The layering threshold is approximately 0.23 times the liquid-gas critical temperature. Upon cooling further, there is a sharp increase at 224 K in the persistence of the surface layers into the bulk material, i.e., an apparently discontinuous change in static structure at the glass transition.

Understanding the Role of Overpotentials in Lithium Ion Conversion Reactions: Visualizing the Interface.

Oxide conversion reactions are known to have substantially higher specific capacities than intercalation materials used in Li-ion batteries, but universally suffer from large overpotentials associated with the formation of interfaces between the resulting nanoscale metal and Li2O products. Here we use the interfacial sensitivity of operando X-ray reflectivity to visualize the structural evolution of ultrathin NiO electrodes and their interfaces during conversion. We observe two additional reactions prior to the well-known bulk, three-dimensional conversion occurring at 0.6 V: an accumulation of lithium at the buried metal/oxide interface (at 2.2 V) followed by interfacial lithiation of the buried NiO/Ni interface at the theoretical potential for conversion (at 1.9 V). To understand the mechanisms for bulk and interfacial lithiation, we calculate interfacial energies using density functional theory to build a potential-dependent nucleation model for conversion. These calculations show that the additional space charge layer of lithium is a crucial component for reducing energy barriers for conversion in NiO.

Molecular assembly of a 3D-ordered multilayer.

Combining strong metal-ligand coordination and pi-pi interactions affords a 3D-ordered molecular-based multilayer. The organization of the assembly is apparent from the optical properties and X-ray reflectivity.

Self-propagating assembly of a molecular-based multilayer.

Accelerated growth of a molecular-based material that is an active participant in its continuing self-propagated assembly has been demonstrated. This nonlinear growth process involves diffusion of palladium into a network consisting of metal-based chromophores linked via palladium.

Selective monitoring of parts per million levels of CO by covalently immobilized metal complexes on glass.

Optical detection of parts-per-million (ppm) levels of CO by a structurally well-defined monolayer consisting of bimetallic rhodium complexes on glass substrates has been demonstrated.