RESUMEN
It is vital to maximize the safety of outdoor constructions, airplanes, and space vehicles by protecting against the impact of airborne debris from increasing winds due to climate change, or from bird strikes or micrometeoroids. In a widely-used compression-molded short glass fiber polyester bulk-molded compound (SGFRP-BMC) with 55% wt. CaCO3 filler, the center of the mother panel has lower impact strength than the outer sections with solidification texture angles and short glass fiber (SGF) orientations being random from 0 to 90 degrees. Therefore, a new double-step process of: (1) reducing commercial fiber length without change in molding equipment; followed by a (2) 0.86 MGy dose of homogeneous low-voltage electron beam irradiation (HLEBI) to both sides of the finished samples requiring no chemicals or additives, which is shown to increase the Charpy impact value (auc) about 50% from 6.26 to 9.59 kJm-2 at median-accumulative probability of fracture, Pf = 0.500. Shortening the SGFs results in higher fiber spacing density, Sf, as the thermal compressive stress site proliferation by action of the CTE difference between the matrix and SGF while the composite cools and shrinks. To boost impact strength further, HLEBI provides additional nano-compressive stresses by generating dangling bonds (DBs) creating repulsive forces while increasing SGF/matrix adhesion. Increased internal cracking apparently occurs, raising the auc.
RESUMEN
Impact by hailstone, volcanic rock, bird strike, or also dropping tools can cause damage to aircraft materials. For maximum safety, the goal is to increase Charpy impact strength (auc) of a carbon-fiber-reinforced thermoplastic polyphenylene sulfide polymer (CFRTP-PPS) composite for potential application to commercial aircraft parts. The layup was three cross-weave CF plies alternating between four PPS plies, [PPS-CF-PPS-CF-PPS-CF-PPS], designated [PPS]4[CF]3. To strengthen, a new process for CFRP-PPS was employed applying homogeneous low voltage electron beam irradiation (HLEBI) to both sides of PPS plies prior to lamination assembly with untreated CF, followed by hot press under 4.0 MPa at 573 K for 8 min. Experimental results showed a 5 kGy HLEBI dose was at or near optimum, increasing auc at each accumulative probability, Pf. Optical microscopy of 5 kGy sample showed a reduction in main crack width with significantly reduced CF separation and pull-out; while, scanning electron microscopy (SEM) and electron dispersive X-ray (EDS) mapping showed PPS adhering to CF. Electron spin resonance (ESR) of a 5 kGy sample indicated lengthening of PPS chains as evidenced by a reduction in dangling bond peak. It Is assumed that 5 kGy HLEBI creates strong bonds at the interface while strengthening the PPS bulk. A model is proposed to illustrate the possible strengthening mechanism.
RESUMEN
In an interlayered carbon fiber-reinforced polycarbonate polymer (CFRPC) composite composed of three sized of CF plies, alternating between four PC sheets, designated [PC]4[CF]3, and a new process of activating CF cross-weave cloth plies directly on both sides with homogeneous low-energy electron beam irradiation (HLEBI) before lamination assembly and hot pressing at 6.0 MPa and 537 K for 8 min was produced. Experimental results show that a dose of 215 kGy of HLEBI raised the bending strength, σb, at each experimental accumulative probability, Pa, with the σb at a median Pa of 0.50, increasing by 25% over that of the untreated sample. Three-parameter Weibull analysis showed that when quality can be controlled, a dose of 215 kGy of HLEBI can raise the statistically lowest bending strength, σs, at Pa = 0 (94.3 Mpa), with a high correlation coefficient. This is because, although it had a higher bending strength than that in the other experimental conditions, the weakest sample of the 215 kGy data set had a much lower σb value than that of the others. Electron spin resonance (ESR) of the CF showed that naturally occurring dangling bonds in CF were increased at 215 kGy. Charge transfer to the PC occurs, apparently generating stronger bonds, which are possibly covalent, resulting in enhanced adhesion at the CF-PC interface.
RESUMEN
New types of hybrid aluminum joints: Al-acrylonitrile butadiene styrene (ABS) carbon fiber reinforced thermoplastic polymer (CFRTP) designated Al/Ni-CFP/ABS, and Al-18-8 Stainless steel, Al/Ni-CFP/18-8, by Ni-plated carbon fiber plug (Ni-CFP) insert not before seen in the literature have been fabricated. The goal is to take advantage of extremely high ~6 mm CF surface area for high adhesion, to enhance the safety level of aircraft and other parts. This is without fasteners, chemical treatment, or glue. First, the CFP is plated with Ni. Second, the higher melting point half-length is spot welded to the CFP; and third, the remaining half-length is fabricated. The ultimate tensile strength (UTS) of Al/Ni-CFP/ABS was raised 15 times over that of Al/ABS. Normalized cUTS according to CFP cross-section by Rule of Mixtures for cAl/Ni-CFP/18-8 was raised over that of cAl/Ni-CFP/18-8 from 140 to 360 MPa. Resistance energy to tensile deformation, UT, was raised 12 times from Al/ABS to Al/Ni-CFP/ABS, and 6 times from Al/CFP/18-8 to Al/Ni-CFP/18-8. Spot welding allows rapid melting followed by rapid solidification for amorphous metal structures minimizing grain boundaries. The Ni-coating lowers or counters the effects of brittle Al4C3 and FexC formation at the interface and prevents damage by impingement to CFs, allowing joints to take on more of the load.
RESUMEN
Bird strike, volcanic rock, hailstones, micrometeoroids, or space debris can cause damage to aircraft and space vehicles, therefore their composite materials must have high impact resistance to maximize safety. In a 55% wt. CaCO3 compression molded short glass fiber polyester GFRP-BMC (bulk molded compound), shortening the nominal 6.4 mm fiber length formulation, by 30 min extended mixing, to 0.44 mm was found to increase Charpy impact values, auc, without a change in the compression molding equipment. Specimens were cut from square panels in a spiral configuration in conformity with ASTM D 6110-02 for orthotropic panels, the flow direction approximately radially outward from the charge. At a median-fracture probability of Pf = 0.50, extended mixing improved auc by 29%, from 7.43 to 9.59 kJm-2, and for each solidification texture angle, namely, 0 to 90 (random), 71, 45 and 18 deg, the auc increased by 25% (6.26 to 7.86 kJm-2), 18% (9.36 to 11.07 kJm-2), 35% (7.68 to 10.37 kJm-2), and 20% (6.96 to 8.36 kJm-2), respectively. This strengthening can be explained by an increased number of thermal compressive stress sites between the glass fiber and matrix due to a difference in the coefficient of thermal expansion (CTE) during cool-down, and shrinkage, with an increased number of spaces between fibers, |Sf| from 217 to approximately 2950 per mm3, enhancing impact energy.
RESUMEN
A literature review of up-to-date methods to strengthen Ti/carbon-fiber-reinforced polymer (CFRP) hybrid joints is given. However, there are little or no studies on Ti/CFRP joints by carbon fiber plug insert, which takes advantage of the extremely high surface adhesion area of ~6 µm CFs. Therefore, we cover the current status and review our previously published results developing hybrid joints by a CF plug insert with spot-welded Ti half-lengths to enhance the safety levels of aircraft fan blades. A thermoset Ti/CF/epoxy joint exhibited an ultimate tensile strength (UTS) of 283 MPa when calculated according to the rule of mixtures (RM) for the CF cross-section portion. With concern for the environment, thermoplastic polymers (TPs) allowed recyclability. However, a drawback is easy CF pull-out from difficult-to-adhere TPs due to insufficient contact sites. Therefore, research on a novel method of homogeneous low voltage electron beam irradiation (HLEBI) to activate a bare CF half-length prior to dipping in a TP resin was reviewed and showed that the UTS by the RM of Ti/EBCF/acrylonitrile butadiene styrene (ABS) and Ti/EBCF/polycarbonate (PC) joints increased 154% (from 55 to 140 MPa) and 829% (from 30 to 195 MPa), respectively, over the untreated sample. The optimum 0.30 MGy HLEBI prevented CF pull-out by apparently growing crystallites into the TP around the CF circumference, raising the UTS amount closer to that of epoxy.
RESUMEN
Strong adhesion between recyclable thermoplastic (TP) polymer and carbon fiber (CF) has always been highly sought after. Therefore, for an interlayered CF reinforced TP polypropylene (CFRTPP) composite composed of 3 sized CF plies, alternating between 4 PP sheets, designated [PP]4[CF]3, a process of activating CF plies directly on both sides with homogeneous low energy electron beam irradiation (EBI) under N2 gas, prior to lamination assembly and hot press of 4.0 MPa at 493 K for 3 min was carried out. Experimental results showed EBI dose of 43.2, 129, or 216 kGy significantly raised Charpy impact values, auc at all fracture probabilities, Pf. The 129 kGy dose appeared to be at or near optimum increasing auc 103%, 83%, and 65% at low-, median-, and high-Pf = 0.07, 0.50, and 0.93; while raising statistically lowest impact value, as at Pf = 0 calculated by 3-dimensional Weibull equation about 110%, indicating increased safety and reliability. It is assumed dangling bonds generated by the EBI rapidly form covalent bonds CF:C:O:C:PP and CF:C:C:PP at the interface, along with cross-linking in the PP near the CF. This is by charge transfer from CF to PP.