A Metasurface-Based LTC Polarization Converter with S-Shaped Split Ring Resonator Structure for Flexible Applications.

This paper presents a metasurface-based linear-to-circular polarization converter with a flexible structure for conformal and wearable applications. The converter consists of nested S- and C-shaped split ring resonators in the unit cell and can convert linearly polarized incident waves into left-handed circularly polarized ones at 12.4 GHz. Simulation results show that the proposed design has a high polarization conversion rate and efficiency at the operating frequency. Conformal tests are also conducted to evaluate the performance under curvature circumstances. A minor shift in the operating frequency is observed when the converter is applied on a sinusoidal wavy surface.

Frequency Switchable Global RFID Tag Antennae with Metal Compatibility for Worldwide Vehicle Transportation.

This paper presents an effective way to design an RFID tag antenna to operate at three different frequencies by incorporating a switching technique. PIN diode has been used to switch the RF frequency because of its good efficiency and simplicity. The conventional dipole-based RFID tag has been improvised with added co-planar ground and PIN diode. The layout of the antenna is designed with a size of 0.083 λ0 × 0.094 λ0 at UHF (80-960) MHz, where λ0 is the free-space wavelength corresponding to the mid-point of the targeted UHF range. The RFID microchip is connected to the modified ground and dipole structures. Bending and meandering techniques on the dipole length help to match the complex chip impedance with the dipole impedance. Additionally, it scales down the total structure of the antenna. Two PIN diodes are placed along the dipole length at appropriate distances with proper biasing. The ON-OFF switching states of the PIN diodes enable the RFID tag antenna to switch over the frequency ranges (840-845) MHz (India), 902-928 MHz (North America), and 950-955 MHz (Japan).

Ultra-Wideband Compact Fractal Antenna for WiMAX, WLAN, C and X Band Applications.

In this paper, a compact dual-wideband fractal antenna is created for Bluetooth, WiMAX, WLAN, C, and X band applications. The proposed antenna consists of a circularly shaped resonator that contains square slots and a ground plane where a gap line is incorporated to increase the gain and bandwidth with a small volume of 40 × 34 × 1.6 mm3. The patch was supported by the FR4 dielectric, which had a permittivity of 4.4 and tan δ = 0.02. A 50 Ω microstrip line fed this antenna. The antenna was designed by the HFSS program, and after that, the simulated results were validated using the measured results. The measurement results confirm that the suggested antenna achieves dual-band frequencies ranging from 2.30 to 4.10 GHz, and from 6.10 GHz to 10.0 GHz, resonating at 2.8, 3.51, 6.53, and 9.37 GHz, respectively, for various applications including commercial, scholarly, and medical applications. Moreover, the antenna's ability to operate within the frequency range of 3.1-10.6 GHz is in accordance with the FCC guidelines for the use of UWB antennas in breast cancer detection. Over the operational bands, the gain varied between 2 and 9 dB, and an efficiency of 92% was attained. A good agreement between the simulation and the measured results was found.

UWB Circular Fractal Antenna with High Gain for Telecommunication Applications.

The present study proposes a new, highly efficient fractal antenna with ultra-wideband (UWB) characteristics. The proposed patch offers a wide simulated operating band that reaches 8.3 GHz, a simulated gain that varies between 2.47 and 7.73 dB throughout the operating range, and a high simulated efficiency that comes to 98% due to the modifications made to the antenna geometry. The modifications carried out on the antenna are composed of several stages, a circular ring extracted from a circular antenna in which four rings are integrated and, in each ring, four other rings are integrated with a reduction factor of 3/8. To further improve the adaptation of the antenna, a modification of the shape of the ground plane is carried out. In order to test the simulation results, the prototype of the suggested patch was built and tested. The measurement results validate the suggested dual ultra-wideband antenna design approach, which demonstrates good compliance with the simulation. From the measured results, the suggested antenna with a compact volume of 40 × 24.5 × 1.6 mm3 asserts ultra-wideband operation with a measured impedance bandwidth of 7.33 GHz. A high measured efficiency of 92% and a measured gain of 6.52 dB is also achieved. The suggested UWB can effectively cover several wireless applications such as WLAN, WiMAX, and C and X bands.

Compact Quad Band MIMO Antenna Design with Enhanced Gain for Wireless Communications.

In this paper, a novel microstrip line-fed meander-line-based four-elements quad band Multiple Input and Multiple Output (MIMO) antenna is proposed with a gain enhancement technique. The proposed structure resonates at four bands simultaneously, that is, 1.23, 2.45, 3.5 and 4.9 GHz, which resemble GPS L2, Wi-Fi, Wi-MAX and WLAN wireless application bands, respectively. The unit element is extended to four elements MIMO antenna structure exhibiting isolation of more than 22 dB between the adjacent elements without disturbing the resonant frequencies. In order to enhance the gain, two orthogonal microstrip lines are incorporated between the antenna elements which result in significant gain improvement over all the four resonances. Furthermore, the diversity performance of the MIMO structure is analyzed. The Envelope Co-Relation Coefficient (ECC), Diversity Gain (DG), Channel Capacity Loss (CCL), Mean Effective Gain (MEG) and Multiplexing Efficiency are obtained as 0.003, 10 dB, 0.0025 bps/Hz, -3 dB (almost) and 0.64 (min.), respectively, which are competent and compatible with practical wireless applications. The Total Active Reflection Coefficient (TARC) resembles the characteristic of the individual antenna elements. The layout area of the overall MIMO antenna is 0.33 λ × 0.29 λ, where λ is the free-space wavelength corresponding to the lowest resonance. The advantage of the proposed structure has been assessed by comparing it with previously reported MIMO structures based on number of antenna elements, isolation, gain, CCL and compactness. A prototype of the proposed MIMO structure is fabricated, and the measured results are found to be aligned with the simulated results.

A Conformal Frequency Reconfigurable Antenna with Multiband and Wideband Characteristics.

A compact flexible multi-frequency antenna for smart portable and flexible devices is presented. The antenna consists of a coplanar waveguide-fed slotted circular patch connected to a rectangular secondary resonator (stub). A thin low-loss substrate is used for flexibility, and a rectangular stub in the feedline is deployed to attain wide operational bandwidth. A rectangular slot is etched in the middle of the circular patch, and a p-i-n diode is placed at its center. The frequency reconfigurability is achieved through switching the diode that distributes the current by changing the antenna's electrical length. For the ON state, the antenna operates in the UWB region for -10 dB impedance bandwidth from 2.76 to 8.21 GHz. For the OFF state of the diode, the antenna operates at the ISM band (2.45/5.8 GHz), WLAN band (5.2 GHz), and lower X-band (8 GHz) with a minimum gain of 2.49 dBi and a maximum gain of 5.8 dBi at the 8 GHz band. Moreover, the antenna retains its performance in various bending conditions. The proposed antenna is suitable for modern miniaturized wireless electronic devices such as wearables, health monitoring sensors, mobile Internet devices, and laptops that operate at multiple frequency bands.

Implementation of a Miniaturized Planar Tri-Band Microstrip Patch Antenna for Wireless Sensors in Mobile Applications.

Antennas in wireless sensor networks (WSNs) are characterized by the enhanced capacity of the network, longer range of transmission, better spatial reuse, and lower interference. In this paper, we propose a planar patch antenna for mobile communication applications operating at 1.8, 3.5, and 5.4 GHz. A planar microstrip patch antenna (MPA) consists of two F-shaped resonators that enable operations at 1.8 and 3.5 GHz while operation at 5.4 GHz is achieved when the patch is truncated from the middle. The proposed planar patch is printed on a low-cost FR-4 substrate that is 1.6 mm in thickness. The equivalent circuit model is also designed to validate the reflection coefficient of the proposed antenna with the S11 obtained from the circuit model. It contains three RLC (resistor-inductor-capacitor) circuits for generating three frequency bands for the proposed antenna. Thereby, we obtained a good agreement between simulation and measurement results. The proposed antenna has an elliptically shaped radiation pattern at 1.8 and 3.5 GHz, while the broadside directional pattern is obtained at the 5.4 GHz frequency band. At 1.8, 3.5, and 5.4 GHz, the simulated peak realized gains of 2.34, 5.2, and 1.42 dB are obtained and compared to the experimental peak realized gains of 2.22, 5.18, and 1.38 dB at same frequencies. The results indicate that the proposed planar patch antenna can be utilized for mobile applications such as digital communication systems (DCS), worldwide interoperability for microwave access (WiMAX), and wireless local area networks (WLAN).

Design of a Tri-Band Wearable Antenna for Millimeter-Wave 5G Applications.

A printed monopole antenna for millimeter-wave applications in the 5G frequency region is described in this research. As a result, the proposed antenna resonates in three frequency bands that are designated for 5G communication systems, including 28 GHz, 38 GHz, and 60 GHz (V band). For the sake of compactness, the coplanar waveguide (CPW) method is used. The overall size of the proposed tri-band antenna is 4 mm × 3 mm × 0.25 mm. Using a watch strap and human tissue, such as skin, the proposed antenna gives steady results. At 28 GHz, 38 GHz, and 60 GHz, the antenna's gain is found to be 5.29 dB, 7.47 dB, and 9 dB, respectively. The overall simulated radiation efficiency is found to be 85% over the watch strap. Wearable devices are a great fit for the proposed tri-band antenna. The antenna prototype was built and tested in order to verify its performance. It can be observed that the simulated and measured results are in close contact. According to our comparative research, the proposed antenna is a good choice for smart 5G devices because of its small size and simple structure, as well as its high gain and radiation efficiency.

Compact Dual-Band Antenna with Paired L-Shape Slots for On- and Off-Body Wireless Communication.

A simple dual-band patch antenna with paired L-shap slots for on- and off-body communications has been presented in this article. The proposed antenna resonates in the industrial, scientific, and medical (ISM) band at two different frequencies, at 2.45 GHz and 5.8 GHz. At the lower frequency band, the antenna's radiation pattern is broadsided directional, whereas it is omni-directional at the higher frequency band. The efficiency and performance of the proposed antenna under the influence of the physical body are improved, and the specific absorption rate (SAR) value is significantly reduced by creating a full ground plane behind the substrate. The substrate's material is FR-4, the thickness of which is 1.6 mm and it has a loss tangent of tanδ = 0.02. The overall size of the proposed design is 40 mm × 30 mm × 1.6 mm. Physical phantoms, such as skin, fat and muscle, are used to evaluate the impact of physical layers at 2.45 GHz and 5.8 GHz. The SAR values are assessed and found to be 0.19 W/kg and 1.18 W/kg at 2.45 GHz and 5.8 GHz, respectively, over 1 gram of mass tissue. The acquired results indicate that this antenna can be used for future on- and off-body communications and wireless services.

Single-fed broadband CPW-fed circularly polarized implantable antenna for sensing medical applications.

Biomedical telemetry relies heavily on implantable antennas. Due to this, we have designed and tested a compact, a circularly polarized, a low-profile biomedical implantable antenna that operate in the 2.45 GHz ISM band. In order to keep the antenna compact, modified co-planar waveguide (CPW) technology is used. Slotted rectangular patch with one 45-degree angle slot and truncated little patch on the left end of the ground plane generate a frequency-range antenna with circular polarization. Using a 0.25-millimeter-thick Roger Duroid-RT5880 substrate with a thickness of εr = 2.2, tanδ = 0.0009 provides flexibility. The volume of the antenna is 21 mm x 13.5 mm x 0.254 mm (0.25λg × 0.16λg × 0.003λg). The antenna covers 2.35-2.55 GHz (200 MHz) in free space and 1.63-1.17 GHz (1.17 GHz) in epidermal tissue. With skin tissue that has more bandwidth, the (x and y)-axis bends of the antenna are also simulated via the simulation. Bended antenna simulations and measurements show excellent agreement. At 2.45 GHz, the skin-like gel had -10dB impedance and 3dB axial ratio (AR) bandwidths of 47.7 and 53.8%, respectively. The ultimate result is that the SAR values are 0.78 W/kg in skin over 1 g of bulk tissue, as determined by simulations. The suggested SAR values are lower than the FCC's maximum allowable limit (FCC). This antenna is small enough to be implanted in the body, making it perfect for biomedical applications.

A wideband circularly polarized CPW-fed substrate integrated waveguide based antenna array for ISM band applications.

This article presents a compact size circularly polarized substrate integrated waveguide (SIW) based wideband antenna array that serves industrial, scientific, and medical (ISM) band applications. A coplanar waveguide (CPW) technique is used to ensure the antenna size compactness. The proposed antenna is fabricated on a low-profile Rogers RT6002 substrate with a dielectric constant of 2.94, tanδ of 0.0012 and an approximate height of 0.76mm. The proposed design covers the frequency range from 2.15 GHz to 3.63 GHz (60.4%) while the axial ratio has a 3 dB bandwidth covering from 2.19 GHz to 2.51 GHz (13%) at the operating band of 2.45 GHz. The antenna is miniaturized and has a size of about 46.50 × 29 × 0.76 mm3. The simulation and experimental results are taken into consideration and there is a good promise between them. Hence, the antenna is a suitable applicant to be utilized for the applications in the ISM band.

A Low Profile Ultra-Wideband Antenna with Reconfigurable Notch Band Characteristics for Smart Electronic Systems.

This study describes the design and implementation of a small printed ultra-wideband (UWB) antenna for smart electronic systems with on-demand adjustable notching properties. A contiguous sub-band between 3-4.1 GHz, 4.45-6.5 GHz, or for both bands concurrently, can be mitigated by the antenna. Numerous technologies and applications, including WiMAX, Wi-Fi, ISMA, WLAN, and sub-6 GHz, primarily utilize these band segments remitted by the UWB. The upper notch band is implemented by inserting an open-ended stub with the partial ground plane; the lower notch band functionality is obtained by etching a U-shaped slot from the radiating structure. The basic UWB mode is then changed to a UWB mode, with a single or dual notch band, using two diodes to achieve reconfigurability. The antenna has a physically compact size of 17 × 23 mm2 and a quasi-omnidirectional maximum gain of 4.9 dBi, along with a high efficiency of more than 80%, according to both simulation and measurement data. A significant bandwidth in the UWB region is also demonstrated by the proposed design, with a fractional bandwidth of 180% in relation to the 5.2 GHz center frequency. Regarding compactness, consistent gain, and programmable notch features, the proposed antenna outperforms the antennas described in the literature. In addition to these benefits, the antenna's compact size makes it simple to incorporate into small electronic devices and enables producers to build many antennas without complications.