Reversible Diels-Alder and Michael Addition Reactions Enable the Facile Postsynthetic Modification of Metal-Organic Frameworks.

Functionalization of metal-organic frameworks (MOFs) is critical in exploring their structural and chemical diversity for numerous potential applications. Herein, we report multiple approaches for the tandem postsynthetic modification (PSM) of various MOFs derived from Zr(IV), Al(III), and Zn(II). Our current work is based on our efforts to develop a wide range of MOF platforms with a dynamic functional nature that can be chemically switched via thermally triggered reversible Diels-Alder (DA) and hetero-Diels-Alder (HDA) ligations. Furan-tagged MOFs (furan-UiO-66-Zr) were conjugated with maleimide groups bearing dienophiles to prepare MOFs with a chemically switchable nature. As HDA pairs, phosphoryl dithioester-based moieties and cyclopentadiene (Cp)-grafted MOF (Cp-MIL-53-Al) were utilized to demonstrate the cleavage and rebonding of the linkages as a function of temperature. In addition to these strategies, the Michael addition reaction was also applied for the tandem PSM of IRMOF-3-Zn. Maleimide groups were postsynthetically introduced in the MOF lattice, which were further ligated with cysteine-based biomolecules via the thiol-maleimide Michael addition reaction. On the basis of the versatility of the herein presented chemistry, we expect that these approaches will help in designing a variety of sophisticated functional MOF materials addressing diverse applications.

Two-in-One: λ-Orthogonal Photochemistry on a Radical Photoinitiating System.

An alkyne functional radical photoinitiator, 2-(4-(2-hydroxy-2-methylpropanoyl)phenoxy)ethyl hex-5-ynoate, and evidence that both reactive moieties - the alkyne and the photoinitiator terminus - can be independently addressed with light of disparate wavelength (λ-orthogonality) are introduced. The alkyne functionality is subjected to a visible light (420 nm) induced copper-catalyzed Huisgen reaction, which is employed for the selective functionalization of the initiator with a poly(ethylene glycol) (PEG) chain. This reaction proceeds completely λ-orthogonal in the presence of the UV-reactive photoinitiating moiety. Conversely, it is demonstrated that the alkyne functionality of the photoinitiator is quantitatively orthogonal to UV irradiation emitted by the pulsing action of an excimer laser (351 nm, pulsed-laser polymerization, PLP) and the generated radical species. In turn, the PEGylated initiator can readily be employed as a macrophotoinitiator during PLP. The introduced λ-orthogonally addressable dual functional initiator can be used in a wide range of applications, including surface lithography and post-synthetic modification of photocured materials.

A photolithographic approach to spatially resolved cross-linked nanolayers.

The preparation of cross-linked nanosheets with 1-2 nm thickness and predefined shape was achieved by lithographic immobilization of trimethacryloyl thioalkanoates onto the surface of Si wafers, which were functionalized with 2-(phenacylthio)acetamido groups via a photoinduced reaction. Subsequent cross-linking via free radical polymerization as well as a phototriggered Diels-Alder reaction under mild conditions on the surface led to the desired nanosheets. Electrospray ionization mass spectrometry (ESI-MS), X-ray photoelectron spectroscopy (XPS), time-of-flight secondary ion mass spectrometry (ToF-SIMS), as well as infrared reflection-absorption spectroscopy (IRRAS) confirmed the success of individual surface-modification and cross-linking reactions. The thickness and lateral size of the cross-linked structures were determined by atomic force microscopy (AFM) for samples prepared on Si wafers functionalized with a self-assembled monolayer of 1H,1H,2H,2H-perfluorodecyl groups bearing circular pores obtained via a polymer blend lithographic approach, which led to the cross-linking reactions occurring in circular nanoareas (diameter of 50-640 nm) yielding an average thickness of 1.2 nm (radical cross-linking), 1.8 nm (radical cross-linking in the presence of 2,2,2-trifluoroethyl methacrylate as a comonomer), and 1.1 nm (photochemical cross-linking) of the nanosheets.

Nanoporous designer solids with huge lattice constant gradients: multiheteroepitaxy of metal-organic frameworks.

We demonstrate the realization of hierarchically organized MOF (metal-organic framework) multilayer systems with pronounced differences in the size of the nanoscale pores. Unusually large values for the lattice constant mismatch at the MOF-MOF heterojunctions are made possible by a particular liquid-phase epitaxy process. The multiheteroepitaxy is demonstrated for the isoreticular SURMOF-2 series [ Liu et al. Sci. Rep. 2012 , 2 , 921 ] by fabricating trilayer systems with lattice constants of 1.12, 1.34, and 1.55 nm. Despite these large (20%) lattice mismatches, highly crystalline, oriented multilayers were obtained. A thorough theoretical analysis of the MOF-on-MOF heterojunction structure and energetics allows us to identify the two main reasons for this unexpected tolerance of large lattice mismatch: the healing of vacancies with acetate groups and the low elastic constant of MOF materials.

Fabrication of highly uniform gel coatings by the conversion of surface-anchored metal-organic frameworks.

We report the fabrication of 3D, highly porous, covalently bound polymer films of homogeneous thickness. These surface-bound gels combine the advantages of metal-organic framework (MOF) materials, namely, the enormous flexibility and the large size of the maximum pore structures and, in particular, the possibility to grow them epitaxially on modified substrates, with those of covalently connected gel materials, namely, the absence of metal ions in the deposited material, a robust framework consisting of covalent bonds, and, most importantly, pronounced stability under biological conditions. The conversion of a SURMOF (surface-mounted MOF) yields a surface-grafted gel. These SURGELs can be loaded with bioactive compounds and applied as bioactive coatings and provide a drug-release platform in in vitro cell culture studies.

Oriented circular dichroism analysis of chiral surface-anchored metal-organic frameworks grown by liquid-phase epitaxy and upon loading with chiral guest compounds.

Oriented circular dichroism (OCD) is explored and successfully applied to investigate chiral surface-anchored metal-organic frameworks (SURMOFs) based on camphoric acid (D- and Lcam) with the composition [Cu2(Dcam)(2x)(Lcam)(2-2x)(dabco)]n (dabco = 1,4-diazabicyclo-[2.2.2]-octane). The three-dimensional chiral SURMOFs with high-quality orientation were grown on quartz glass plates by using a layer-by-layer liquid-phase epitaxy method. The growth orientation, as determined by X-ray diffraction (XRD), could be switched between the [001] and [110] direction by using either OH- or COOH-terminated substrates. These SURMOFs were characterized by using OCD, which confirmed the ratio as well as the orientation of the enantiomeric linker molecules. Theoretical computations demonstrate that the OCD band intensities of the enantiopure [Cu2(Dcam)2(dabco)]n grown in different orientations are a direct result of the anisotropic nature of the chiral SURMOFs. Finally, the enantiopure [Cu2(Dcam)2(dabco)]n and [Cu2(Lcam)2(dabco)]n SURMOFs were loaded with the two chiral forms of ethyl lactate [(+)-ethyl-D-lactate and (-)-ethyl-L-lactate)]. An enantioselective enrichment of >60 % was observed by OCD when the chiral host scaffold was loaded from the racemic mixture.

Post-synthetic modification of metal-organic framework thin films using click chemistry: the importance of strained C-C triple bonds.

In this work, we demonstrate that strain-promoted azide-alkyne cycloaddition (SPAAC) yields virtually complete conversion in the context of the post-synthetic modification (PSM) of metal-organic frameworks (MOFs). We use surface-anchored MOF (SURMOF) thin films, [Zn2(N3-bdc)2(dabco)], grown on modified Au substrates using liquid-phase epitaxy (LPE) as a model system to first show that, with standard click chemistry, presently, the most popular method for rendering additional functionality to MOFs via PSM, quantitative conversion yields, cannot be reached. In addition, it is virtually impossible to avoid contaminations of the product by the cytotoxic Cu(I) ions used as a catalyst, a substantial problem for applications in life sciences. Both problems could be overcome by SPAAC, where a metal catalyst is not needed. After optimization of reaction conditions, conversion yields of nearly 100% could be achieved. The consequences of these results for various applications of PSM-modified SURMOFs in the fields of membranes, optical coatings, catalysis, selective gas separation, and chemical sensing are briefly discussed.

Surface-anchored MOF-based photonic antennae.

The loading of a metal-organic framework (MOF), [Cu(3)(btc)(2)xH(2)O] HKUST-1, with europium ß-diketonate complexes is studied with the goal to using the porous molecular framework as a photonic antenna. Whereas loading of HKUST-1 powder particles produced via the conventional solvothermal synthesis method was strongly hindered, for HKUST-1 SURMOFs, thin MOF films fabricated using the liquid phase epitaxy method, a high filling factor can be achieved. The optical properties of the HKUST-1-MOFs before and after loading were analysed with the aid of luminescence spectroscopy. Careful analysis of the absorption spectra reveals the presence of an effective energy transfer between the HKUST-1 framework and the Eu(3+) centers.

New approaches for bottom-up assembly of tobacco mosaic virus-derived nucleoprotein tubes on defined patterns on silica- and polymer-based substrates.

The capability of some natural molecular building blocks to self-organize into defined supramolecular architectures is a versatile tool for nanotechnological applications. Their site-selective integration into a technical context, however, still poses a major challenge. RNA-directed self-assembly of tobacco mosaic virus-derived coat protein on immobilized RNA scaffolds presents a possibility to grow nucleoprotein nanotubes in place. Two new methods for their site-selective, bottom-up assembly are introduced. For this purpose, isothiocyanate alkoxysilane was used to activate oxidic surfaces for the covalent immobilization of DNA oligomers, which served as linkers for assembly-directing RNA. Patterned silanization of surfaces was achieved (1) on oxidic surfaces via dip-pen nanolithography and (2) on polymer surfaces (poly(dimethylsiloxane)) via selective oxidization by UV-light irradiation in air. Atomic force microscopy and X-ray photoelectron spectroscopy were used to characterize the surfaces. It is shown for the first time that the combination of the mentioned structuring methods and the isothiocyanate-based chemistry is appropriate (1) for the site-selective immobilization of nucleic acids and, thus, (2) for the formation of viral nanoparticles by bottom-up self-assembly after adding the corresponding coat proteins.

The biocompatibility of metal-organic framework coatings: an investigation on the stability of SURMOFs with regard to water and selected cell culture media.

Highly porous thin films based on a [Cu(bdc)(2)](n) (bdc = benzene-1,4-dicarboxylic acid) metal-organic framework, MOF, grown using liquid-phase epitaxy (LPE) show remarkable stability in pure water as well as in artificial seawater. This opens the possibility to use these highly porous coatings for environmental and life science applications. Here we characterize in detail the stability of these SURMOF 2 thin films under aqueous and cell culture conditions. We find that the material degrades only very slowly in water and artificial seawater (ASW) whereas in typical cell culture media (PBS and DMEM) a rapid dissolution is observed. The release of Cu(2+) ions resulting from the dissolution of the SURMOF 2 in the liquids exhibits no adverse effect on the adhesion of fibroblasts, prototype eukaryotic cells, to the substrate and their subsequent proliferation, thus demonstrating the biocompatibility of SURMOF 2 surface coatings. Thus, the results are an important step toward application of these porous materials as a slow release matrix, for example, for pharmaceuticals and growth factors.

Hydrogen Separation Performance of UiO-66-NH2 Membranes Grown via Liquid-Phase Epitaxy Layer-by-Layer Deposition and One-Pot Synthesis.

The quality assurance of hydrogen fuel for mobile applications is assessed by the guidelines and directives given in the European and international standards. However, the presence of impurities in the hydrogen fuel, in particular nitrogen, water, and oxygen, is experienced in several refueling stations. Within this work, metal-organic framework (MOF)-based membranes are investigated as a fine-purification stage of the hydrogen fuel. Three H2/N2 concentrations have been used to analyze the separation factor of UiO-66-NH2 membranes prepared using the layer-by-layer (LBL) and the one-pot (OP) synthesis methods. It is shown that the separation factor for an equimolar ratio is 14.4% higher for the LBL sample compared to the OP membrane, suggesting a higher orientation and continuity of the LBL surface-supported metal-organic framework (SURMOF). Using an equimolar ratio of H2/N2, it is shown that selective separation of hydrogen over nitrogen occurs with a separation factor of 3.02 and 2.64 for the SURMOF and MOF membrane, respectively. To the best of our knowledge, this is the highest reported performance for a single-phase UiO-66-NH2 membrane. For higher hydrogen concentrations, the separation factor decreases due to reduced interactions between pore walls and N2 molecules.

Design of chemically activated polymer microwells by one-step UV-lithography for stem cell adhesion.

A novel method to produce sub-microwalled chemically activated polymer microwells by one-step UV-lithography under ambient conditions which are selectively coated with gelatin is introduced. The dimensions as well as the shape of the resulting polystyrene structures are both tunable merely by the irradiation time through one and the same mask. It is shown that the UV-irradiation initiates three effects at those surface areas which are not covered by the mask: (i) oxidation, (ii) cross-linking, and (iii) degradation of polystyrene. The superposition of those effects results in the formation of microscaled, oxidized polymer wells separated by polymer walls, whereas the polymer walls are formed below the mask structures. Topographical changes induced by the UV-irradiation are investigated by atomic force microscopy after different irradiation times. It is shown by X-ray photoelectron spectroscopy and ellipsometric investigations that the chemical composition of the irradiated areas and the degradation of polystyrene reach an equilibrium state after an irradiation time of 10 min. The lateral distribution of the cross-linked and oxidized and of the nonmodified polystyrene after irradiation was determined by fluorescence microscopy and time-of-flight secondary ion mass spectrometry. After the irradiated samples were treated with gelatin solution, it was found that stem cells selectively attach to the irradiated areas. This is due to the selective immobilization of the gelatin on the irradiated polymer areas, which was proved by X-ray photoelectron spectroscopy experiments.

Liquid-Phase Quasi-Epitaxial Growth of Highly Stable, Monolithic UiO-66-NH2 MOF thin Films on Solid Substrates.

Invited for this month's cover is the group of Dr. Tawheed Hashem from the Karlsruhe Institute of Technology. The cover picture shows a successful synthesis of high quality, monolithic UiO-66-NH2 MOF thin films on diverse solid substrates via a low-temperature liquid phase epitaxy method. The achievement of continuous MOF-coatings with low defect densities and pronounced stability against high temperatures and hot water was proven. The new type of coatings clearly outperforms other reported types of MOF thin films. Read the full text of their Communication at https://doi.org/10.1002/open.201900324.

Liquid-Phase Quasi-Epitaxial Growth of Highly Stable, Monolithic UiO-66-NH2 MOF thin Films on Solid Substrates.

High quality, monolithic UiO-66-NH2 thin films on diverse solid substrates have been prepared via a low temperature liquid phase epitaxy method. The achievement of continuous films with low defect densities and great stability against high temperatures and hot water is proven, clearly outperforming other reported types of MOF thin films.

Introducing electrical conductivity to metal-organic framework thin films by templated polymerization of methyl propiolate.

We herein present a case study on the templated, Pd-catalyzed polymerization reaction of methyl propiolate in the confined pore space of three different surface anchored metal-organic framework (SURMOF) systems in order to introduce electrical conductivity to MOF thin films and provide predictions for potential device integrations. To gain comprehensive insight into the influence of the template on polymerization, we chose Cu(bpdc), Cu2(bdc)2(dabco) and HKUST-1 because of their different types of pore channels, 1D, quasi-1D and 3D, and their free pore volumes. Well-defined MOF thin films were prepared using layer-by-layer deposition, which allows for the application of several characterization techniques not applicable for conventional powder MOFs. With SEM, AFM, XRD, MALDI-ToF/MS, ToF-SIMS and QCM, we were able to investigate the behaviour of the polymer formation. For lower dimensional pore channels, we find a depot-like release of monomeric units leading to top-layer formation determined by desorption kinetics, whereas for the 3D channels, quick release of an excess amount of monomers was observed and polymerization proceeds perfectly. Despite polymerization issues, control over the maximum chain lengths and the molecular weight distribution was achieved depending on the dimensionality of the pore systems. For the HKUST-1 system, polymerization was optimized and we were able to measure the electrical conductivity introduced by the conjugated polymer inside the channels.

Conductive Metal-Organic Framework Thin Film Hybrids by Electropolymerization of Monosubstituted Acetylenes.

1-Hexyne monomers were potentiostatically electropolymerized upon confinement in 1D channels of a surface-mounted metal-organic framework Cu(BDC) (SURMOF-2). A layer-by-layer deposition method allowed for SURMOF depostition on substrates with prepatterned electrodes, making it possible to characterize electrical conductivity in situ, i.e., without having to delaminate the conductive polymer thin film. Successful polymerization was evidenced by mass spectroscopy, and the electrical measurements demonstrated an increase of the electrical conductivity of the MOF material by 8 orders of magnitude. Extensive DFT calculations revealed that the final conductivity is limited by electron hopping between the conductive oligomers.

Mobility of charge carriers in self-assembled monolayers.

We present a new approach to study charge transport within 2D layers of organic semi-conductors (OSCs) using atomic force microscopy (AFM)-based lithography applied to self-assembled monolayers (SAMs), fabricated from appropriate organothiols. The extent of lateral charge transport was investigated by insulating pre-defined patches within OSC-based SAMs with regions of insulating SAM made from large band gap alkanethiolates. The new method is demonstrated using a phenyl-linked anthracenethiolate (PAT), 4-(anthracene-2-ylethynyl)benzyl thiolate. I-V characteristics of differently shaped PAT-islands were measured using the AFM tip as a top electrode. We were able to determine a relationship between island size and electrical conductivity, and from this dependence, we could obtain information on the lateral charge transport and charge carrier mobility within the thin OSC layers. Our study demonstrates that AFM nanografting of appropriately functionalized OSC molecules provides a suitable method to determine intrinsic mobilities of charge carriers in OSC thin films. In particular, this method is rather insensitive with regard to influence of grain boundaries and other defects, which hamper the application of conventional methods for the determination of mobilities in macroscopic samples.

Siloxane-functionalised surface patterns as templates for the ordered deposition of thin lamellar objects.

A novel method is demonstrated for ordered deposition of thin lamellar objects from a liquid environment onto solid substrates by solid/fluid/solid-driven organisation. Surface functionalisation forms a template pattern that accumulates the lamellar objects by site-selective wetting of the target area without the need for a physical fluid containment. Contrary to conventional handling methods, no mechanical contact occurs, which facilitates the ordered deposition without wrinkles or ruptures. An additive and a subtractive process for the creation of such templates are presented. The subtractive process starts with the complete silanisation of the substrate in the vapour phase followed by site-selective oxygen plasma treatment of the siloxane film. The additive process uses microcontact printing to transfer the target pattern. Both processes are characterised by optical inspection of the wetting contours and it is found that site-selective plasma treatment shows a better pattern fidelity. The patterns obtained by site-selective plasma treatment are also subject to ToF-SIMS analysis and show good chemical contrast between hydrophilic and hydrophobic areas. The ordered deposition of lamellar objects by this new method is demonstrated for 60 nm thick ultramicrotome sections of epoxide resin on pre-patterned glass substrates.

Isothiocyanate-functionalized RGD peptides for tailoring cell-adhesive surface patterns.

With the advances made in surface patterning by micro- and nanotechnology, alternative methods to immobilize biomolecules for different purposes are highly desired. RGD peptides are commonly used to create cell-attractive surfaces for cell-biological and also medical applications. We have developed a fast, one-step method to bind RGD peptides covalently to surfaces by thiourea formation, which can be applied to structured and unstructured materials. RGD peptides were fused to an isothiocyanate anchor during synthesis and directly immobilized on amino-terminated surfaces. The spreading behavior of fibroblasts and the formation of focal contacts served to prove the applicability of the coupling method. Two different linear peptides and one cyclic peptide were compared. All the peptides induced spreading behavior and the formation of focal contacts in murine fibroblasts. Adhesion was specific as cells neither recognized the corresponding negative control peptides nor spread in the presence of soluble H-RGDS-OH peptide. We successfully applied our coupling method to functionalize surface patterns created by microcontact printing (microCP) and chemical etching. Cells recognize areas selectively coated with RGD-containing peptides, proliferate and maintain this preference during long-term cultivation. Our method significantly facilitates surface modification with any kind of peptide - even for the preparation of peptide-functionalized small surface areas.

Light-Induced Step-Growth Polymerization of AB-Type Photo-Monomers at Ambient Temperature.

We introduce two AB-type monomers able to undergo a facile catalyst-free photoinduced polycycloaddition of photocaged dienes, enabling rapid Diels-Alder ligations under UV-irradiation (λmax = 350 nm) at ambient temperature, closely adhering to Carother's equation established by a careful kinetic study (17800 g mol-1 < Mw < 24700 g mol-1). The resulting macromolecules were in-depth analyzed via size exclusion chromatography (SEC) and nuclear magnetic resonance (NMR) spectroscopy. Additionally, SEC hyphenated to high resolution-electrospray ionization-mass spectrometry (HR-ESI-MS) enabled the careful mapping of the end group structure of the generated polymers. Furthermore, we demonstrate that both monomer systems can be readily copolymerized. The study thus demonstrates that Diels-Alder ligation resting upon photocaged dienes is a powerful tool for accessing step-growth polymers.