Influence of Oxygen-Containing Functional Groups on the Environmental Properties, Transformations, and Toxicity of Carbon Nanotubes.

Carbon nanotubes (CNTs) have unique physical and chemical properties that drive their use in a variety of commercial and industrial applications. CNTs are commonly oxidized prior to their use to enhance dispersion in polar solvents by deliberately grafting oxygen-containing functional groups onto CNT surfaces. In addition, CNT surface oxides can be unintentionally formed or modified after CNTs are released into the environment through exposure to reactive oxygen species and/or ultraviolet irradiation. Consequently, it is important to understand the impact of CNT surface oxidation on the environmental fate, transport, and toxicity of CNTs. In this review, we describe the specific role of oxygen-containing functional groups on the important environmental behaviors of CNTs in aqueous media (e.g., colloidal stability, adsorption, and photochemistry) as well as their biological impact. We place special emphasis on the value of systematically varying and quantifying surface oxides as a route to identifying quantitative structure-property relationships. The role of oxygen-containing functional groups in regulating the efficacy of CNT-enabled water treatment technologies and the influence of surface oxides on other carbon-based nanomaterials are also evaluated and discussed.

Graphene/polymer nanocomposite degradation by ultraviolet light: The effects of graphene nanofillers and their potential for release.

The ultraviolet (UV)-induced degradation of graphene/polymer nanocomposites was investigated in this study. Specifically, the effect of few-layer graphene nanofillers on the degradation of a thermoplastic polyurethane (TPU) and the release potential of graphene from the degraded nanocomposite surfaces were assessed. Graphene/TPU (G/TPU) nanocomposites and neat TPU were UV-exposed under both dry and humid conditions in the NIST SPHERE, a precisely controlled, high intensity UV-weathering device. Neat TPU and G/TPU were characterized over the time course of UV exposure using color measurements and infrared spectroscopy, for appearance and chemical changes, respectively. Changes in thickness and surface morphology were obtained with scanning electron microscopy. A new fluorescence quenching measurement approach was developed to identify graphene sheets at the nanocomposite surface, which was supported by contact angle measurements. The potential for graphene release from the nanocomposite surface was evaluated using a tape-lift method followed by microscopy of any particles present on the tape. The findings suggest that graphene improves the service life of TPU with respect to UV exposure, but that graphene becomes exposed at the nanocomposite surface over time, which may potentially lead to its release when exposed to small mechanical forces or upon contact with other materials.

Detection and Quantification of Graphene-Family Nanomaterials in the Environment.

An increase in production of commercial products containing graphene-family nanomaterials (GFNs) has led to concern over their release into the environment. The fate and potential ecotoxicological effects of GFNs in the environment are currently unclear, partially due to the limited analytical methods for GFN measurements. In this review, the unique properties of GFNs that are useful for their detection and quantification are discussed. The capacity of several classes of techniques to identify and/or quantify GFNs in different environmental matrices (water, soil, sediment, and organisms), after environmental transformations, and after release from a polymer matrix of a product is evaluated. Extraction and strategies to combine methods for more accurate discrimination of GFNs from environmental interferences as well as from other carbonaceous nanomaterials are recommended. Overall, a comprehensive review of the techniques available to detect and quantify GFNs are systematically presented to inform the state of the science, guide researchers in their selection of the best technique for the system under investigation, and enable further development of GFN metrology in environmental matrices. Two case studies are described to provide practical examples of choosing which techniques to utilize for detection or quantification of GFNs in specific scenarios. Because the available quantitative techniques are somewhat limited, more research is required to distinguish GFNs from other carbonaceous materials and improve the accuracy and detection limits of GFNs at more environmentally relevant concentrations.

Biodegradation of Carbon Nanotube/Polymer Nanocomposites using a Monoculture.

The biodegradation rates of carbon nanotube (CNT)/ polymer nanocomposites (PNCs) containing poly-ε-caprolactone (PCL) were investigated using Pseudomonas aeruginosa, a microorganism commonly found in the environment. CNT/PCL nanocomposite mass loss profiles revealed that the rate of PCL matrix biodegradation decreased systematically as the CNT loading increased from 0.1 to 10% w/w. Addition of even a low CNT loading (<1% w/w) caused the CNT/PCL biodegradation rate constant to decrease by more than 50%. Similar trends in biodegradation rate were observed for both pristine and oxidized multiwall CNTs embedded in PCL. During PCL matrix biodegradation, CNT accumulation was observed at the surface of CNT/PCL nanocomposites and single particle inductively coupled-mass spectrometry experiments revealed no measurable CNT release to the culture fluid. Experimental data indicated that biodegradation proceeded as a result of biofilm formation on the CNT/PCL nanocomposites and decreased as a function of CNT loading due to the cytotoxicity of CNTs toward P. aeruginosa and the physical barrier presented by the surface-accumulated CNTs to the underlying PCL substrate. As the CNT loading in the CNT/PCL nanocomposites increased, the microbial proliferation of planktonic cells in the surrounding media also decreased as did the biodegradation rate of PCL samples present in the same reactors. Results from this study demonstrate that the inclusion of CNTs into polymer matrices could increase the environmental persistence of polymers in lakes, landfills, and surface waters.

Photochemical transformation of graphene oxide in sunlight.

Graphene oxide (GO) is promising in scalable production and has useful properties that include semiconducting behavior, catalytic reactivity, and aqueous dispersibility. In this study, we investigated the photochemical fate of GO under environmentally relevant sunlight conditions. The results indicate that GO readily photoreacts under simulated sunlight with the potential involvement of electron-hole pair creation. GO was shown to photodisproportionate to CO2, reduced materials similar to reduced GO (rGO) that are fragmented compared to the starting material, and low molecular-weight (LMW) species. Kinetic studies show that the rate of the initially rapid photoreaction of GO is insensitive to the dissolved oxygen content. In contrast, at longer time points (>10 h), the presence of dissolved oxygen led to a greater production of CO2 than the same GO material under N2-saturated conditions. Regardless, the rGO species themselves persist after extended irradiation equivalent to 2 months in natural sunlight, even in the presence of dissolved oxygen. Overall, our findings indicate that GO phototransforms rapidly under sunlight exposure, resulting in chemically reduced and persistent photoproducts that are likely to exhibit transport and toxic properties unique from parent GO.

Interactions of microorganisms with polymer nanocomposite surfaces containing oxidized carbon nanotubes.

In many environmental scenarios, the fate and impact of polymer nanocomposites (PNCs) that contain carbon nanotubes (CNT/PNCs) will be influenced by their interactions with microorganisms, with implications for antimicrobial properties and the long-term persistence of PNCs. Using oxidized single-wall (O-SWCNTs) and multi-wall CNTs (O-MWCNTs), we explored the influence that CNT loading (mass fraction≤0.1%-10%) and type have on the initial interactions of Pseudomonas aeruginosa with O-CNT/poly(vinyl alcohol) (PVOH) nanocomposites containing well-dispersed O-CNTs. LIVE/DEAD staining revealed that, despite oxidation, the inclusion of O-SWCNTs or O-MWCNTs caused PNC surfaces to exhibit antimicrobial properties. The fraction of living cells deposited on both O-SWCNT and O-MWCNT/PNC surfaces decreased exponentially with increasing CNT loading, with O-SWCNTs being approximately three times more cytotoxic on a % w/w basis. Although not every contact event between attached microorganisms and CNTs led to cell death, the cytotoxicity of the CNT/PNC surfaces scaled with the total contact area that existed between the microorganisms and CNTs. However, because the antimicrobial properties of CNT/PNC surfaces require direct CNT-microbe contact, dead cells were able to shield living cells from the cytotoxic effects of CNTs, allowing biofilm formation to occur on CNT/PNCs exposed to Pseudomonas aeruginosa for longer time periods.

Toward tailored functional design of multi-walled carbon nanotubes (MWNTs): electrochemical and antimicrobial activity enhancement via oxidation and selective reduction.

Multiwalled carbon nanotubes (MWNTs) are utilized in a number of sectors as a result of their favorable electronic properties. In addition, MWNT antimicrobial properties can be exploited or considered a potential liability depending on their intended application and handling. The ability to tailor electrochemical and antimicrobial properties using economical and conventional treatment processes introduces the potential to significantly enhance product performance. Oxygen functional groups are known to influence several MWNT properties, including redox activity. Here, MWNTs were functionalized with oxygen groups using standard acid treatments followed by selective reduction via annealing. Chemical derivatization coupled to X-ray photoelectron spectroscopy was utilized to quantify specific surface oxygen group concentration after variable treatment conditions, which were then correlated to observed trends in electrochemical and antimicrobial activities. These activities were evaluated as the potential for MWNTs to participate in the oxygen reduction reaction and to have the ability to promote the oxidation of glutathione. The compiled results strongly suggest that the reduction of surface carboxyl groups and the redox activity of carbonyl groups promote enhanced MWNT reactivity and elucidate the opportunity to design functional MWNTs for enhanced performance in their intended electrochemical or antimicrobial application.

Proton conductivity of columnar ceria thin-films grown by chemical vapor deposition.

Columnar thin films of undoped ceria were grown by metal-organic chemical vapor deposition. The films, deposited on Pt-coated MgO(100) substrates, display a columnar microstructure with nanometer scale grain size and ~30% overall porosity. Through-plane (thickness mode) electrical conductivity was measured by AC impedance spectroscopy. Proton conduction is observed below 350-400 °C, with a magnitude that depends on gas-phase water vapor pressure. The overall behavior suggests proton transport that occurs along exposed grain surfaces and parallel grain boundaries. No impedance due to grain boundaries normal to the direction of transport is observed. The proton conductivity in the temperature range of 200-400 °C is approximately four times greater than that of nanograined bulk ceria, consistent with enhanced transport along aligned grain surfaces in the CVD films.

Evaluation of bioaccumulation of nanoplastics, carbon nanotubes, fullerenes, and graphene family materials.

Bioaccumulation is a key factor in understanding the potential ecotoxicity of substances. While there are well-developed models and methods to evaluate bioaccumulation of dissolved organic and inorganic substances, it is substantially more challenging to assess bioaccumulation of particulate contaminants such as engineered carbon nanomaterials (CNMs; carbon nanotubes (CNTs), graphene family nanomaterials (GFNs), and fullerenes) and nanoplastics. In this study, the methods used to evaluate bioaccumulation of different CNMs and nanoplastics are critically reviewed. In plant studies, uptake of CNMs and nanoplastics into the roots and stems was observed. For multicellular organisms other than plants, absorbance across epithelial surfaces was typically limited. Biomagnification was not observed for CNTs and GFNs but were observed for nanoplastics in some studies. However, the reported absorption in many nanoplastic studies may be a consequence of an experimental artifact, namely release of the fluorescent probe from the plastic particles and subsequent uptake. We identify that additional work is needed to develop analytical methods to provide robust, orthogonal methods that can measure unlabeled (e.g., without isotopic or fluorescent labels) CNMs and nanoplastics.

Quantitative evaluation of released nanomaterials from carbon nanotube epoxy nanocomposites during environmental exposure and mechanical treatment.

Carbon nanotubes (CNTs) are promising nanomaterials exhibiting high thermal and electrical conductivities, significant stiffness, and high tensile strength. As a result, CNTs have been utilized as additives to enhance properties of various polymeric materials in a broad range of fields. In this study, we investigated the release of CNTs from CNT epoxy nanocomposites exposed to environmental weathering and mechanical stresses. The presence and amount of CNTs released from degraded polymer nanocomposites is important because CNTs can impact physiological systems in humans and environmental organisms. The weathering experiments in this study included nanocomposite exposure to both UV and a water spray, to simulate sunlight and rain exposure, whereas mechanical stresses were induced by shaking and ultrasonication. CNT release from epoxy nanocomposites was quantified by a 14C-labeling method that enabled measurement of the CNT release rates after different weathering and mechanical treatments. In this study, a sample oxidizer was used prior to liquid scintillation counting, because it was shown to reduce interferences from the presence of polymeric materials and achieve a high recovery (95%). Polymer nanocomposite degradation was confirmed by attenuated total reflectance-Fourier transform infrared spectroscopy (ATR-FTIR), scanning electron microscopy (SEM), and light microscopy. A continuous release of 14C-labeled nanomaterials was observed after each UV and simulated rain exposure period, with 0.23% (mass/mass) of the total embedded mass of CNTs being released from the CNT nanocomposite during the full weathering process, suggesting that the water spray induced sufficient mechanical stress to eliminate the protective effect of the surface agglomerated CNT network. Importantly, additional mechanical stresses imposed on the weathered nanocomposites by shaking and ultrasonication resulted in further release of approximately 0.27% (mass /mass).

Surface reaction and transport in mixed conductors with electrochemically-active surfaces: a 2-D numerical study of ceria.

A two-dimensional, small-bias model has been developed for describing transport through a mixed ionic and electronic conductor (MIEC) with electrochemically-active surfaces, a system of particular relevance to solid oxide fuel cells. Utilizing the h-adaptive finite-element method, we solve the electrochemical potential and flux for both ionic and electronic species in the MIEC, taking the transport properties of Sm(0.15)Ce(0.85)O(1.925-δ) (SDC15). In addition to the ionic flux that flows between the two sides of the cell, there are two types of electronic fluxes: (1) cross-plane current that flows in the same general direction as the ionic current, and (2) in-plane current that flows between the catalytically-active MIEC surface and the metal current collectors. From an evaluation of these fluxes, the macroscopic interfacial resistance is decomposed into an electrochemical reaction resistance and an electron diffusion-drift resistance, the latter associated with the in-plane electronic current. Analysis of the experimental data for the interfacial resistance for hydrogen electro-oxidation on SDC15 having either Pt or Au current collectors (W. Lai and S. M. Haile, J. Am. Ceram. Soc., 2005, 88, 2979-2997; W. C. Chueh, W. Lai and S. M. Haile, Solid State Ionics, 2008, 179, 1036-1041) indicates that surface reaction rather than electron migration is the overall rate-limiting step, and suggests furthermore that the surface reaction rate, which has not been directly measured in the literature, scales with pO2(-1/4). The penetration depth for the in-plane electronic current is estimated at 0.6 µm for the experimental conditions of interest to SDC15, and is found to attain a value as high as 4 µm within the broader range of computational conditions.

Heterogenous catalysis mediated by plasmon heating.

We introduce a new method for performing and miniaturizing many types of heterogeneous catalysis involving nanoparticles. The method makes use of the plasmon resonance present in nanoscale metal catalysts to provide the necessary heat of reaction when illuminated with a low-power laser. We demonstrate our approach by reforming a flowing, liquid mixture of ethanol and water over gold nanoparticle catalysts in a microfluidic channel. Plasmon heating of the nanoparticles provides not only the heat of reaction but the means to generate both water and ethanol vapor locally over the catalysts, which in turn allows the chip and the fluid lines to remain at room temperature. The measured products of the reaction, CO(2), CO, and H(2), are consistent with catalytic steam reforming of ethanol. The approach, which we refer to as plasmon-assisted catalysis, is general and can be used with a variety of endothermic catalytic processes involving nanoparticles.

Influence of polymer type and carbon nanotube properties on carbon nanotube/polymer nanocomposite biodegradation.

The interaction of anaerobic microorganisms with carbon nanotube/polymer nanocomposites (CNT/PNC) will play a major role in determining their persistence and environmental fate at the end of consumer use when these nano-enabled materials enter landfills and encounter wastewater. Motivated by the need to understand how different parameters (i.e., polymer type, microbial phenotype, CNT characteristics) influence CNT/PNC biodegradation rates, we have used volumetric biogas measurements and kinetic modeling to study biodegradation as a function of polymer type and CNT properties. In one set of experiments, oxidized multiwall carbon nanotubes (O-MWCNTs) with a range of CNT loadings 0-5% w/w were incorporated into poly-ε-caprolactone (PCL) and polyhydroxyalkanoates (PHA) matrices and subjected to biodegradation by an anaerobic microbial community. For each CNT/PNC, complete polymer biodegradation was ultimately observed, although the rate of biodegradation was inhibited above certain critical CNT loadings dependent upon the polymer type. Higher loadings of pristine MWCNTs were needed to decrease the rate of polymer biodegradation compared to O-MWCNTs, an effect ascribed principally to differences in CNT dispersion within the polymer matrices. Above certain CNT loadings, a CNT mat of similar shape to the initial PNC was formed after polymer biodegradation, while below this threshold, CNT aggregates fragmented in the media. In situations where biodegradation was rapid, methanogen growth was disproportionately inhibited compared to the overall microbial community. Analysis of the results obtained from this study indicates that the inhibitory effect of CNTs on polymer biodegradation rate is greatest under conditions (i.e., polymer type, microbial phenotype, CNT dispersion) where biodegradation of the neat polymer is slowest. This new insight provides a means to predict the environmental fate, persistence, and transformations of CNT-enabled polymer materials.

Selection of an Optimal Abrasion Wheel Type for Nano-Coating Wear Studies under Wet or Dry Abrasion Conditions.

Nanocoatings have numerous potential applications in the indoor environment, such as flooring finishes with increased scratch- and wear-resistance. However, given concerns about the potential environmental and human health effects of nanomaterials, it is necessary to develop standardized methods to quantify nanomaterial release during use of these products. One key choice for mechanical wear studies is the abrasion wheel. Potential limitations of different wheels include the release of fragments from the wheel during abrasion, wearing of the wheel from the abrasion process, or not releasing a sufficient number of particles for accurate quantitative analysis. In this study, we evaluated five different wheels, including a typically used silicon oxide-based commercial wheel and four wheels fabricated at the National Institute of Standards and Technology (NIST), for their application in nanocoating abrasion studies. A rapid, nondestructive laser scanning confocal microscopy method was developed and used to identify released particles on the abraded surfaces. NIST fabricated a high performing wheel: a noncorrosive, stainless-steel abrasion wheel containing a deep cross-patch. This wheel worked well under both wet and dry conditions, did not corrode in aqueous media, did not release particles from itself, and yielded higher numbers of released particles. These results can be used to help develop a standardized protocol for surface release of particles from nanoenabled products using a commercial rotary Taber abraser.

The Impacts of Moisture and Ultraviolet Light on the Degradation of Graphene Oxide/Polymer Nanocomposites.

The extent to which hydrophilic GO nanofillers regulate polymer degradation during exposure to a combination of ultraviolet (UV) radiation and moisture is presently unknown. Accordingly, this study systematically evaluated the effect of GO on polymer degradability under both humid UV and dry UV conditions. Both GO accumulation at the polymer nanocomposite (PNC) surface and GO release following degradation were also investigated. Different mass loadings of GO were incorporated into waterborne polyurethane (WBPU), a commonly used exterior coating, and the resulting GO/WBPU nanocomposites were exposed to precisely controlled accelerated weathering conditions using the NIST Simulated Photodegradation via High Energy Radiant Exposure (SPHERE) device. Thickness loss and infrared spectroscopy measurements indicated GO slightly improved the durability of WBPU under dry UV conditions but not under humid UV conditions. Raman spectroscopy, scanning electron microscopy, and atomic force microscopy modulus measurements indicated that GO accumulation occurred at and near the PNC surface under both conditions but to a more rapid extent under humid UV conditions. Minimal GO release occurred under dry UV conditions as measured with Raman spectroscopy of aqueous run-off from a simulated rain spray applied to degraded PNCs. In contrast, PNC surface transformations under humid UV conditions suggested that GO release occurred.

Evaluating performance, degradation, and release behavior of a nanoform pigmented coating after natural and accelerated weathering.

Pigments with nanoscale dimensions are added to exterior coatings to achieve desirable color and gloss properties. The present study compared the performance, degradation, and release behavior of an acrylic coating that was pigmented by a nanoform of Cu-phthalocyanine after both natural (i.e., outdoor) and accelerated weathering. Samples were weathered outdoors in three geographically distinct locations across the United States (Arizona, Colorado, Maryland) continuously for 15 months. Identically prepared samples were also artificially weathered under accelerated conditions (increased ultraviolet (UV) light intensity and elevated temperatures) for three months, in one-month increments. After exposure, both sets of samples were characterized with color, gloss, and infrared spectroscopy measurements, and selectively with surface roughness measurements. Results indicated that UV-driven coating oxidation was the principal degradation pathway for both natural and accelerated weathering samples, with accelerated weathering leading to an increased rate of oxidation without altering the fundamental degradation pathway. The inclusion of the nanoform pigment reduced the rate of coating oxidation, via UV absorption by the pigment, leading to improved coating integrity compared to non-pigmented samples. Release measurements collected during natural weathering studies indicated there was never a period of weathering, in any location, that led to copper material release above background copper measurements. Lab-based release experiments performed on samples weathered naturally and under accelerated conditions found that the release of degraded coating material after each type of exposure was diminished by the inclusion of the nanoform pigment. Release measurements also indicated that the nanoform pigment remained embedded within the coating and did not release after weathering.

Impedance spectra of mixed conductors: a 2D study of ceria.

In this paper we develop an analytical framework for the study of electrochemical impedance of mixed ionic and electronic conductors (MIEC). The framework is based on non-equilibrium thermodynamics and it features the coupling of electrochemical reactions, surface transport and bulk transport processes. We utilize this work to analyze two-dimensional systems relevant for fuel cell science via the finite element method (FEM). Alternate current impedance spectroscopy (AC-IS or IS) of a ceria symmetric cell is simulated near equilibrium conditions (zero bias) for a wide array of working conditions including variations of temperature and H(2) partial pressure on a two-dimensional doped ceria sample with patterned metal electrodes. The model shows agreement between computed IS curves and the experimental literature where the relative error on the impedance is consistently below 2%. Important two-dimensional effects such as the impact of thickness decrease and the influence of variable electronic and ionic diffusivities on the impedance spectra are also explored.

Long-term wear effects on nanosilver release from commercially available food contact materials.

Potential consumer exposure to nanoparticles (NPs) from nanoenabled food contact materials (FCMs) has been a driving force for migration studies of NPs from FCMs. Although NP migration from fresh, unused FCMs was not previously observed, conditions that result in significant changes to the surface of FCMs have not been investigated for NP migration into food. Therefore, a quantitative assessment of nanoparticle release from commercially available nanosilver-enabled FCMs was performed using an abrasion protocol to simulate cleaning, cutting, scraping and other stressful use conditions. Laser scanning confocal microscopy (LSCM) analysis showed a general increase in root mean square (RMS) roughness after FCM abrasion, and particle count (for particle sizes from 80 nm to 960 nm) at the surface was 4 orders of magnitude higher for the abraded FCMs. Migration was evaluated using both water and 3% (v/v, volume fraction) acetic acid as food simulants. Low concentrations of total Ag were detected in water simulants with a small portion (<10 ng dm-2) in the form of silver nanoparticles (AgNPs). Median particle diameter ranged from 39 nm to 50 nm with particle number concentrations on the order of 106 particles dm- 2. Total Ag migration into 3% (v/v) acetic acid was significantly higher than in water; however, 3% (v/v) acetic acid was not suitable for evaluation of NP release due to dissolution of AgNPs to Ag+ under acidic solution chemistries.

Long-term wear effects on nanosilver release from commercially available food contact materials.

Potential consumer exposure to nanoparticles (NPs) from nanoenabled food contact materials (FCMs) has been a driving force for migration studies of NPs from FCMs. Although NP migration from fresh, unused FCMs was not previously observed, conditions that result in significant changes to the surface of FCMs have not been investigated for NP migration into food. Therefore, a quantitative assessment of nanoparticle release from commercially available nanosilver-enabled FCMs was performed using an abrasion protocol to simulate cleaning, cutting, scraping and other stressful use conditions. Laser scanning confocal microscopy (LSCM) analysis showed a general increase in root mean square (RMS) roughness after FCM abrasion, and particle count (for particle sizes from 80 nm to 960 nm) at the surface was 4 orders of magnitude higher for the abraded FCMs. Migration was evaluated using both water and 3% (v/v, volume fraction) acetic acid as food simulants. Low concentrations of total Ag were detected in water simulants with a small portion (<10 ng dm-2) in the form of silver nanoparticles (AgNPs). Median particle diameter ranged from 39 nm to 50 nm with particle number concentrations on the order of 106 particles dm- 2. Total Ag migration into 3% (v/v) acetic acid was significantly higher than in water; however, 3% (v/v) acetic acid was not suitable for evaluation of NP release due to dissolution of AgNPs to Ag+ under acidic solution chemistries.

Effects of high pressure processing on Toxoplasma gondii oocysts on raspberries.

Oocysts are the environmentally resistant life stage of Toxoplasma gondii. Humans can become infected by accidentally ingesting the oocysts in water or from contaminated produce. Severe disease can occur in immunocompromised individuals, and nonimmune pregnant women can infect their offspring. Chronic infection is associated with decreased mental functions, vision and hearing problems, and some mental disorders such as schizophrenia. High pressure processing (HPP) is a commercial method used to treat food to eliminate pathogens. Treatment of produce to eliminate viable T. gondii oocysts would provide a means to protect consumers. The present study was done to better define the effects of HPP on oocysts placed on raspberries. Raspberries were chosen because they are a known source of a related human intestinal parasite, Cyclospora cayetanensis. Raspberries were inoculated with 5 x 10(4) oocysts of the VEG strain of T. gondii for 20 hr prior to HPP. Individual raspberries were exposed to 500 MPa, 400 MPa, 340 MPa, 300 MPa, 270 MPa, 250 MPa, 200 MPA, 100 MPa, or no MPa treatment for 60 sec in a commercial HPP unit (1 MPa = 10 atm = 147 psi). Treatment of raspberries with 340 MPa for 60 sec was needed to render oocysts spot inoculated on the raspberries noninfectious for mice. Treatment of raspberries with 200 MPa or less for 60 sec was not effective in rendering oocysts noninfectious for mice.