Magnetic actuator for the control and mixing of magnetic bead-based reactions on-chip.

While magnetic bead (MB)-based bioassays have been implemented in integrated devices, their handling on-chip is normally either not optimal--i.e. only trapping is achieved, with aggregation of the beads--or requires complex actuator systems. Herein, we describe a simple and low-cost magnetic actuator to trap and move MBs within a microfluidic chamber in order to enhance the mixing of a MB-based reaction. The magnetic actuator consists of a CD-shaped plastic unit with an arrangement of embedded magnets which, when rotating, generate the mixing. The magnetic actuator has been used to enhance the amplification reaction of an enzyme-linked fluorescence immunoassay to detect Escherichia coli O157:H7 whole cells, an enterohemorrhagic strain, which have caused several outbreaks in food and water samples. A 2.7-fold sensitivity enhancement was attained with a detection limit of 603 colony-forming units (CFU) /mL, when employing the magnetic actuator.

Deposition of photocatalytically active TiO2 films by inkjet printing of TiO2 nanoparticle suspensions obtained from microwave-assisted hydrothermal synthesis.

In this paper, we present an inkjet printing approach suited for the deposition of photocatalytically active, transparent titanium oxide coatings from an aqueous, colloidal suspension. We used a bottom-up approach in which a microwave-assisted hydrothermal treatment of titanium propoxide aqueous solutions in the presence of ethylenediaminetetraacetic acid and triethanolamine was used to create suspensions containing titania nanoparticles. Different inkjet printing set-ups, electromagnetic and piezoelectric driven, were tested to deposit the inks on glass substrates. The presence of preformed titania nanoparticles was expected to make it possible to reduce the heating temperature necessary to obtain the functionality of photocatalysis which can widen the application range of the approach to heat-sensitive substrates. We investigated the crystallinity and size of the obtained nanoparticles by electron microscopy and dynamic light scattering. The rheological properties of the suspensions were evaluated against the relevant criteria for inkjet printing and the jettability was analyzed. The photocatalytic activity of the obtained layers was analyzed by following the decomposition of a methylene blue solution under UV illumination. The influence of the heat treatment temperature on the film roughness, thickness and photocatalytic activity was studied. Good photocatalytic performance was achieved for heat treatments at temperatures as low as 150 °C, introducing the possibility of using this approach for heat-sensitive substrates.

Chemical Solution Deposition of Insulating Yttria Nanolayers as Current Flow Diverter in Superconducting GdBa2Cu3O7-δ Coated Conductors.

The primary benefit of a metallic stabilization/shunt in high temperature superconductor (HTS) coated conductors (CCs) is to prevent joule heating damage by providing an alternative path for the current flow during the HTS normal state transition (i.e., quench). However, the shunt presence in combination with unavoidable fluctuations in the critical current (I c) of the HTS film can develop a localized quench along the CC's length if the operational current is kept close to I c. This scenario, also known as the hot-spot regime, can lead to the rupture of the CC if the local quench does not propagate fast enough. The current flow diverter (CFD) is the CC architecture concept that has proven to increase the conductor's robustness against a hot-spot regime by simply boosting the quench velocity in the CC, which avoids the shunt compromise in some applications. This work investigates a practical manufacturing route for incorporating the CFD architecture in a reel-to-reel system via the preparation of yttrium oxide (Y2O3) as an insulating thin nanolayer (∼100 nm) on top of a GdBa2Cu3O7 (GdBCO) superconductor. Chemical solution deposition (CSD) using ink jet printing (IJP) is shown to be a suitable manufacturing approach. Two sequences of the experimental steps have been investigated, where oxygenation of the GdBCO layer is performed after or before the solution deposition and the Y2O3 nanolayer thermal treatment formation step. A correlated analysis of the microstructure, in situ oxygenation kinetics, and superconducting properties of the Ag/Y2O3/GdBCO trilayer processed under different conditions shows that a new customized functional CC can be prepared. The successful achievement of the CFD effect in the case of the preoxygenated customized CC was confirmed by measuring the current transfer length, thus demonstrating the effectiveness of the CSD-IJP as a processing method.

High frequency response of thick REBCO coated conductors in the framework of the FCC study.

A thorough microwave response study of high temperature superconductors, considered as an alternative beam screen coating, has become integral in the design decisions for CERN's future research infrastructure. Here, we present the surface resistance [Formula: see text] of various [Formula: see text] (RE = rare earth) coated conductors available in large scale as a function of magnetic field in a broad temperature range measured by a Hakki-Coleman type resonator with resonant frequency [Formula: see text]. Analysis of the high frequency dissipation supported by DC transport characterization reveals the vortex dynamics in thick [Formula: see text] films. Determined microscopic vortex parameters span over a wide range of magnitudes and reflect the relevance of the superconducting layer's microstructure. We demonstrate that the depinning frequencies [Formula: see text] surpass [Formula: see text], which confirms the operation in high performing, low dissipation pinning regime at measurement conditions. Surface impedance extrapolation to FCC-hh conditions points towards a significant outperformance of copper by coated conductors in terms of surface resistance. The surface resistance margins would open up potential ways for a more efficient frontier circular collider.

Direct Visualization of Current-Stimulated Oxygen Migration in YBa2Cu3O7-δ Thin Films.

The past years have witnessed major advancements in all-electrical doping control on cuprates. In the vast majority of cases, the tuning of charge carrier density has been achieved via electric field effect by means of either a ferroelectric polarization or using a dielectric or electrolyte gating. Unfortunately, these approaches are constrained to rather thin superconducting layers and require large electric fields in order to ensure sizable carrier modulations. In this work, we focus on the investigation of oxygen doping in an extended region through current-stimulated oxygen migration in YBa2Cu3O7-δ superconducting bridges. The underlying methodology is rather simple and avoids sophisticated nanofabrication process steps and complex electronics. A patterned multiterminal transport bridge configuration allows us to electrically assess the directional counterflow of oxygen atoms and vacancies. Importantly, the emerging propagating front of current-dependent doping δ is probed in situ by optical microscopy and scanning electron microscopy. The resulting imaging techniques, together with photoinduced conductivity and Raman scattering investigations, reveal an inhomogeneous oxygen vacancy distribution with a controllable propagation speed permitting us to estimate the oxygen diffusivity. These findings provide direct evidence that the microscopic mechanism at play in electrical doping of cuprates involves diffusion of oxygen atoms with the applied current. The resulting fine control of the oxygen content would permit a systematic study of complex phase diagrams and the design of electrically addressable devices.

Electrochemical Tuning of Metal Insulator Transition and Nonvolatile Resistive Switching in Superconducting Films.

Modulation of carrier concentration in strongly correlated oxides offers the unique opportunity to induce different phases in the same material, which dramatically change their physical properties, providing novel concepts in oxide electronic devices with engineered functionalities. This work reports on the electric manipulation of the superconducting to insulator phase transition in YBa2Cu3O7-δ thin films by electrochemical oxygen doping. Both normal state resistance and the superconducting critical temperature can be reversibly manipulated in confined active volumes of the film by gate-tunable oxygen diffusion. Vertical and lateral oxygen mobility may be finely modulated, at the micro- and nano-scale, by tuning the applied bias voltage and operating temperature thus providing the basis for the design of homogeneous and flexible transistor-like devices with loss-less superconducting drain-source channels. We analyze the experimental results in light of a theoretical model, which incorporates thermally activated and electrically driven volume oxygen diffusion.

Polar domain walls trigger magnetoelectric coupling.

Interface physics in oxides heterostructures is pivotal in material's science. Domain walls (DWs) in ferroic systems are examples of naturally occurring interfaces, where order parameter of neighboring domains is modified and emerging properties may develop. Here we show that electric tuning of ferroelastic domain walls in SrTiO3 leads to dramatic changes of the magnetic domain structure of a neighboring magnetic layer (La1/2Sr1/2MnO3) epitaxially clamped on a SrTiO3 substrate. We show that the properties of the magnetic layer are intimately connected to the existence of polar regions at twin boundaries of SrTiO3, developing at , that can be electrically modulated. These findings illustrate that by exploiting the responsiveness of DWs nanoregions to external stimuli, even in absence of any domain contribution, prominent and adjustable macroscopic reactions of neighboring layers can be obtained. We conclude that polar DWs, known to exist in other materials, can be used to trigger tunable responses and may lead to new ways for the manipulation of interfacial emerging properties.