RESUMEN
The interactions between high-intensity laser and matter produce particle flux and electromagnetic radiation over a wide energy range. The generation of extremely intense transient fields in the radio frequency-microwave regime has been observed in femtosecond-to-nanosecond laser pulses with 1011-1020-W/cm2 intensity on both conductive and dielectric targets. These fields typically cause saturation and damage to electronic equipment inside and near an experimental chamber; nevertheless, they can also be effectively used as diagnostic tools. Accordingly, the characterization of electromagnetic pulses (EMPs) is extremely important and currently a popular topic for present and future laser facilities intended for laser-matter interaction. The picosecond and sub-picosecond laser pulses are considerably shorter than the characteristic electron discharge time (â¼0.1 ns) and can be efficient in generating GHz EMPs. The EMP characterization study of femtosecond laser-driven solid targets is currently mainly in the order of 100 mJ laser energy, in this study, the EMP generated by intense (Joule class) femtosecond laser irradiation of solid targets has been measured as a function of laser energy, laser pulse duration, focal spot size, and target materials. And a maximum electric field of the EMP reaching up to 105 V/m was measured. Analyses of experimental results confirm a direct correlation between measured EMP energy and laser parameters in the ultrashort pulse duration regime. The EMP signals generated by femtosecond laser irradiation of solid targets mainly originate from the return current inside the target after hot electron excitation. Numerical simulations of EMP are performed according to the target charging model, which agree well with the experimental results.
RESUMEN
In this paper, we report that the angular dispersion of the output pulses in a nonlinear process can be efficiently compensated by using a cascaded prism(s) and short hollow-core fiber (HCF) configuration. Here, the prism(s) is used to suppress the angular dispersion and transform it into spatial chirp, while the HCF is used for removing this spatial chirp and the residual angular dispersion, which can also significantly improve the beam quality. The feasibility of this novel method is numerically and experimentally investigated with the ultra-broadband idler pulses centered at 1250 nm wavelength and generated by an LBO crystal based non-collinear optical parametric amplifier. The proof-of-principle experiment shows that the angular dispersion can be effectively removed and ultra-broadband idler pulses with good spectral quality and spatial profile can be obtained. The total transmission efficiency in the experiment is around 67% and the measured M x2 and M y2 can reach 1.12 and 1.04, respectively. To the best of our knowledge, this is the first reported ultra-broadband angular dispersion compensation scheme combining prism(s) and HCF, which can remarkably eliminate the angular dispersion while simultaneously possesses high efficiency, good spectral and beam spatial quality.
RESUMEN
It is of crucial significance to investigate and suppress pre-pulses on nanosecond time scale because the intense pre-plasma generated by them may have enough time to expand and, thus, cause fatal impact on laser-matter interactions. In this research, we analyze the potential origins of pre-pulses on nanosecond time scale in a typical Ti:sapphire chirped pulse amplification laser system. Based on the analysis, the initial status of these generated pre-pulses in the SULF-1PW laser is measured and investigated. Then different measures, including fine control on the time synchronization and the replacement for the Ti:sapphire, are adopted in the SULF-1PW laser to suppress these pre-pulses with respective origins, which can promote the energy ratio between the main pulse and these pre-pulses by 2-3 orders of magnitude. This research not only improves the temporal contrast of the SULF-1PW laser on nanosecond time scale but also provides beneficial guidance for the design and construction of similar laser facilities.
RESUMEN
In this paper, we report that the conversion efficiency and spectrum of femtosecond optical parametric amplification (fs-OPA) can be significantly enhanced by employing a compact cascaded femtosecond OPA (CF-OPA) scheme with the self-compensation of the temporal walk-off between two nonlinear gain media. Correspondingly, the gain related temporal contrast can also be improved. The feasibility of the CF-OPA method using three cascaded BBO crystals is numerically and experimentally analyzed. Moreover, by replacing the conventional fs-OPA with the CF-OPA and optimizing the design, the performance of a nonlinear temporal filter combining cross-polarized wave generation and fs-OPA is comprehensively improved. The experimental results demonstrate the superiority of the CF-OPA scheme, which can generate high-performance cleaned pulses at 1 kHz repetition rate with energy of 340µJ, energy fluctuation below 0.9% (RMS), spectral width of 97 nm (FWHM), Fourier-transform-limited pulse width of 12 fs and temporal contrast better than 10-12. To the best of our knowledge, this is the first reported temporal walk-off self-compensated quasi-collinear CF-OPA geometry adopting three cascaded BBO crystals, which can be easily generalized to other wavelengths or nonlinear crystals. The above nonlinear temporal filter with a CF-OPA scheme has the rarest comprehensive parameters, which can provide excellent seed pulses for PW and 10 PW class femtosecond laser systems.
RESUMEN
A novel design of double chirped pulse amplification laser systems implementing a combination of negatively and positively chirped pulse amplification is proposed for the first time. Without utilizing any extra dispersion compensation element, this design can sufficiently cancel out the second-, third- and especially fourth-order dispersion simultaneously, just by optimizing the parameters of the stretcher and compressor in first chirped pulse amplification stage which applies negatively chirped pulse amplification. The numerical results indicate that near Fourier-transform-limited pulse duration about 20fs can be achieved in high-peak-power femtosecond laser systems up to multi-Petawatt level. This design not only provides a feasible solution for the dispersion control in high-contrast and high-peak-power femtosecond laser systems, but also can avoid the degradation of temporal contrast induced by seed energy loss in the presence of additional dispersion compensation components.
RESUMEN
Extremely strong-field terahertz (THz) radiation in free space has compelling applications in nonequilibrium condensed matter state regulation, all-optical THz electron acceleration and manipulation, THz biological effects, etc. However, these practical applications are constrained by the absence of high-intensity, high-efficiency, high-beam-quality, and stable solid-state THz light sources. Here, the generation of single-cycle 13.9-mJ extreme THz pulses from cryogenically cooled lithium niobate crystals and a 1.2% energy conversion efficiency from 800 nm to THz are demonstrated experimentally using the tilted pulse-front technique driven by a home-built 30-fs, 1.2-Joule Ti:sapphire laser amplifier. The focused peak electric field strength is estimated to be 7.5 MV cm-1 . A record of 1.1-mJ THz single-pulse energy at a 450 mJ pump at room temperature is produced and observed that the self-phase modulation of the optical pump can induce THz saturation behavior from the crystals in the substantially nonlinear pump regime. This study lays the foundation for the generation of sub-Joule THz radiation from lithium niobate crystals and will inspire more innovations in extreme THz science and applications.