DFT Study of α-Keggin-type Iso-polyoxotungstate Anions [HnW12O40](8-n)- (n =1-4): Can [H4W12O40]4- Exist?

The Keggin-type iso-polyoxotungstate (iso-POT) anions [HnW12O40](8-n)- 's, in which their central vacancies are occupied by protons, are attractive materials. It is of importance to reveal if the vacancies can be fully occupied by four protons. For further understanding the speciation of these iso-POT anions, relative stabilities and proton transfer reactions between H1[Hn-1W12O40](8-n)- and [HnW12O40](8-n)- were examined in detail by using the first-principles calculations (the nudged elastic band method, the synchronous transit-guided quasi-Newton method, the intrinsic reaction coordinate method, and frequency analysis calculations). Thermochemistry analysis of the proton transfer was also performed. [HnW12O40](8-n)- was energetically more stable than H1[Hn-1W12O40](8-n)-. This held for n = 4. According to the results of thermochemistry analysis, the rate constant and the Wigner correction were respectively 3.1 × 101 s-1 and 2.2 at T = 298.15 K for the proton transfer from H1[H3W12O40]4- to [H4W12O40]4-, indicating that [H4W12O40]4- can exist when H1[H3W12O40]4- is formed by protonating [H3W12O40]5-.

How Viscous Is the Solidlike Structure at the Interface of Ionic Liquids? A Study Using Total Internal Reflection Fluorescence Spectroscopy with a Fluorescent Molecular Probe Sensitive to High Viscosity.

Aiming at the evaluation of the viscosity of the interfacial solidlike structure of ionic liquids (ILs), we performed total internal reflection fluorescence (TIRF) spectroscopy for N,N-diethyl-N'-phenyl-rhodamine (Ph-DER), a fluorescent probe that is sensitive to viscosity in a high-viscosity range. TIRF spectra at the glass interface of trioctylmethylammonium bis(nonafluorobutanesulfonyl)amide (TOMAC4C4N), a hydrophobic IL, showed that the fluorescence intensity of Ph-DER increases with the decrease of the evanescence penetration depth, suggesting that there exists a high-viscosity region at the interface. In contrast, glycerol, which is a molecular liquid with a bulk viscosity similar to that of TOMAC4C4N, did not show such a fluorescence increase, supporting that the formation of a highly viscous solidlike structure at the interface is intrinsic to ILs. A model analysis suggested that the high viscous region at the glass interface of TOMAC4C4N is at least twice thicker than the ionic multilayers at the air interface, implying that the solid substrate enhances the ordering of the interfacial structure of ILs. The viscosity at the glass interface of TOMAC4C4N was found to be at least 40 times higher than that of the liquid bulk.

Capillary zone electrophoresis determination of fluoride in seawater using transient isotachophoresis.

We developed capillary zone electrophoresis (CZE) with indirect UV detection for the determination of fluoride (F-) in seawater using transient isotachophoresis (tITP) as an on-line concentration procedure. A method of correcting sample salinity effects was also proposed so that F- concentrations were obtained using a calibration graph. The proposed method is simple: it requires no sample pretreatment aside from dilution. The following optimum conditions were established: background electrolyte (BGE), 5 mM 2,6-pyridinedicarboxylic acid (PDC) adjusted to pH 3.5 containing 0.03% m/v hydroxypropyl methylcellulose (HPMC); detection wavelength, 200 nm; vacuum (50 kPa) injection period of sample, 5 s (254 nL); and applied voltage, 23 kV with the sample inlet side as the cathode. The limit of detection (LOD, S/N = 3) and limit of quantification (LOQ, S/N = 10) for F- reached 0.024 and 0.070 mg/L, respectively. The respective values of the relative standard deviation (RSD) of the peak area, peak height, and migration time for F- were 2.5, 3.4, and 0.30%. The proposed method was applied for the determination of F- in seawater samples collected from coastal waters of western Japan during August 26-28, 2014. Both results obtained using standard addition method and a calibration graph agreed with those obtained using a conventional spectrophotometric method.

[Prognostic factors and efficacy of molecular targeted therapy for metastatic clear cell renal cell carcinoma].

We retrospectively reviewed the medical records of patients with metastatic clear cell renal cell carcinoma who received molecular targeted therapy between 2005 and 2011. Cancer-specific survival was analyzed using the Kaplan-Meier method. Predictors of cancer-specific survival were analyzed using the Cox regression hazards model. A total of 89 patients, consisting of 50 first line patients and 39 patients receiving prior cytokine were included in the analysis. The two-year cancer-specific survival rate of the firstlinegroup was 60.2% and that of theprior cytokinethe rapy group was 62.1%. In univariateanalysis, Karnofsky performance status (KPS)＜80%, time from diagnosis to treatment less than one year, bone metastasis and C-reactive protein (CRP)＞1.3 mg/dl in were statistically significant prognostic factors (p＜0.05). In multivariate analysis, time from diagnosis to treatment less than one year (HR 2.46, 95%CI 1.11-5.82, p＝0.025) and CRP (HR 4.92, 95%CI 2.23-11.3, p＜0.001) were independent prognostic factors. Time from diagnosis to treatment less than one year and CRP were independent prognostic factors in patients who received molecular targeted therapy.

Combination of crystal growth with optical floating zone and evaluation of Nd3+:LaAlO3 crystals with the dynamic nuclear polarization of 139La and 27Al.

Producing a polarized lanthanum (La) target with high polarization and long relaxation time is crucial for realizing time-reversal violation experiments using polarized neutron beams. We use a LaAlO3 crystal doped with a small amount of Nd3+ ions for the polarized lanthanum target. Optimizing the amount of Nd3+ ions is considerably important because the achievable polarization and relaxation time strongly depend on this amount. We established a fundamental method to grow single crystals of Nd3+:LaAlO3 using an optical floating zone method that employs halogen lamps and evaluated the crystals with the dynamic nuclear polarization (DNP) method for polarizing nuclear spins. Two crystal samples were grown by ourselves and evaluated with the DNP at 1.3 K and 2.3 T for the first time, except for the target materials of protons. The enhancement of nuclear magnetic resonance signals for 139La and 27Al was successfully observed, and the enhancement factors were eventually 3.5 ± 0.3 and 13 ± 3 for the samples with Nd3+ ions of 0.05 and 0.01 mol. %, respectively. These enhancement factors correspond to absolute vector polarizations of 0.27% ± 0.02% (Nd3+ 0.05 mol. %) and 1.4% ± 0.3% (Nd3+ 0.01 mol. %). Although the obtained polarizations are still low, they are acceptable as a first step. The combination scheme of the crystal growth and the evaluation of the crystals is found to be effectively applicable for optimizing the amount of Nd3+ ions for improving the performance of the polarized target.

Discovery of flometoquin, a novel quinoline insecticide.

Flometoquin, 2-ethyl-3,7-dimethyl-6-[4-(trifluoromethoxy)phenoxy]quinolin-4-yl methyl carbonate, is a novel insecticide with a structurally unique phenoxy-quinoline. It was discovered in 2004 by the collaborative research of Nippon Kayaku and Meiji Seika Kaisha, Ltd. (currently, Mitsui Chemicals Crop & Life Solutions, Inc.). The compound demonstrates strong and quick insecticidal action against a variety of thrips species at the nymphal and adult stages through contact and feeding activity, which could minimize crop damage and economic loss by insect pest species. In addition, flometoquin is safe for tested non-target arthropods, which makes it suitable for controlling the insect pests mentioned above under Integrated Pest Management (IPM) programs. Here, we describe a structure-activity relationship study from lead generation to the discovery of flometoquin and its insecticidal properties, including knockdown activity and effects against non-targeted arthropods.

Redox reactions between ABTS•+ and dihydroxybenzenes as studied by cyclic voltammetry.

Redox reactions between several types of polyphenols and 2,2'-azino-bis(3-ethylbenzothiazoline-6-sulfonic acid) radical cation (ABTS•+) used in a trolox equivalent antioxidant capacity (TEAC) assay were monitored by continuous cyclic voltammetry. The TEAC assay is one of the effective methods for clarifying the radical scavenging reaction mechanism of antioxidants. We obtained information on whether the reaction was a simple electron transfer, an electron transfer involving a subsequent chemical reaction of the antioxidant itself, or an electron transfer involving a coupling reaction between ABTS•+ and the antioxidant.

Quantification of trace elements in natural samples by electrospray ionization mass spectrometry with a size-exclusion column based on the formation of metal-aminopolycarboxylate complexes.

Metal ions were determined by ESI-MS in the negative ion mode as monovalent negative ions of their aminopolycarboxylic acid (APC) complexes, e.g., [Al(cydta)](-), [Pb(Hcydta)](-), where excess amounts of the APC agents were added to sample solutions. Among several APCs studied, we chose trans-1,2-diaminocyclohexane-N,N,N',N'-tetraacetic acid (CyDTA) as the best chelating agent because of higher stabilities and higher sensitivities of the complexes. The ionization efficiency of these metal complexes was strongly affected by the presence of matrix salts, e.g., NaCl, KNO(3), and etc. Thus, a size exclusion column (Sephadex G-10) was used for the online separation of the metal-APC complexes from other matrix salts. This method was successfully applied to the quantitative analyses for total amounts of Al, Ni, Cu, Zn, and Pb in the biological certified reference materials, olive leaves (BCR-062) and plankton (BCR-414). The detection limits of the present methods for these elements were several to several ten nanomolar levels. Moreover, this approach was extended to determine ultratraces of fluoride based on the formation of the ternary complex of aluminum, fluoride and nitrilotriacetic acid (NTA), i.e., [AlF(nta)](-). Its detection limit was 10 nM and was 2 orders of magnitude better than that of a fluoride ion selective electrode method. This method was applied to determine fluoride in tap water, river water, and green tea samples.

Identification of aluminum species in an aluminum-accumulating plant, hydrangea (Hydrangea macrophylla), by electrospray ionization mass spectrometry.

The use of electrospray ionization mass spectrometry (ESI-MS) in negative ion mode was investigated as a direct probe for identifying Al species in Al-accumulating hydrangea (Hydrangea macrophylla) samples. Cell sap solutions of hydrangea leaves were purified using Sephadex G-10 liquid chromatography and each fraction was analyzed using ESI-MS and ESI-MS/MS to identify Al species. In hydrangea leaves, a 1:1 Al-citrate complex was found as [AlH(-1)cit](-) (m/z 215), where H(3)cit denotes citric acid. This result is consistent with that of Ma et al. who used (27)Al-NMR.

Direct Detection of Aqueous CO2 by Infrared Waveguide Spectroscopy with an Amorphous Fluoropolymer Coating Rod.

Infrared waveguide spectroscopy using a sapphire rod coated with an amorphous fluoropolymer (Cytop, Asahi Glass Co., ltd, Japan) has been developed in order to directly observe CO2 in aqueous solutions. Since the amorphous fluoropolymer has a relatively high gas-permeability and hydrophobic feature, the aqueous CO2 transmits into the amorphous fluoropolymer coating film, but water cannot penetrate into the film. Good linearity of calibration curves for CO2 in the gas and the aqueous solution were obtained.

Development of Tetrahydrofuran/Water Optical Waveguide and Its Application to the Observation of Extraction Behavior of 1-Anilino-8-naphtalene Sulfonate at the Tetrahydrofuran/Water Interface.

A stable two-phase sheath flow using tetrahydrofuran (THF) for an inner flow and water for an outer flow was formed in a glass capillary, and worked as a stable liquid-core/liquid-cladding optical waveguide (THF/water LLW). Although THF and water were miscible with any ratio, the length of the stable THF/water LLW at 0.9 - 2.1 cm s-1 reached at least 150 mm. The THF/water LLW was applied to the observation of extraction behavior of solvatochromic fluorescence dye, 1-anilino-8-naphtalene sulfonate (ANS), through the THF/water interface. ANS was added to the water phase (clad solution) and its fluorescence, which was excited with the guided light (355 nm) through the LLW, was observed by changing the position of the detector. While the ANS stayed in the region of 70% THF to the end of the LLW without the addition of cationic surfactant, hexadecyltrimethylammonium ion (CTA+) at pH 3 and 11, the ion-pair of ANS and CTA+ was extracted into the higher concentration region of THF with the addition of CTA+ at pH 11.

Liquid core waveguide spectrophotometry for the sensitive determination of nitrite in river water samples.

A flow injection analysis system was built with a liquid core waveguide spectrophotometric detector using an 80 cm Teflon AF-1600 capillary tube (2,2-bistrifluoromethyl-4,5-difluoro-1,3-dioxole/tetrafluoroethylene). The system was applied to determine nitrite ion in river water samples. The lower limit of detection for nitrite was 2.1 nmol dm(-3) (0.1 ng dm(-3) as NO(2)(-)) and the relative standard deviation of measurements was typically 0.56% (n = 5) at 0.21 micromol dm(-3).

A novel method for determination of inorganic oxyanions by electrospray ionization mass spectrometry using dehydration reactions.

Novel methods for the determination of inorganic oxyanions by electrospray (ES) ionization mass spectrometry have been developed using dehydration reactions between oxyanions and carboxylic acids at the ES interface. Twelve oxyanions (VO3 (-) , CrO4 (2-) , MoO4 (2-) , WO4 (2-) , BO3 (3-) , SiO3 (2-) , SiO4 (4-) , AsO4 (4-) , AsO2 (-) , SeO4 (2-) , SeO3 (2-) and NO2 (-) ), out of 16 tested, reacted with at least one of four aminopolycarboxylic acids, i.e. iminodiacetic acid (IDA), nitrilotriacetic acid (NTA), trans-1,2-diaminocyclohexane-N,N,N',N'-tetraacetic acid and triethylenetetramine-N,N,N',N″,N'″,N'″-hexaacetic acid, at the ES interface to produce the dehydration products that gave intense mass ion responses, sufficient for trace analysis. As examples, trace determinations of Cr(VI) and silica in water samples were achieved after online ion exchange chromatography, where the dehydration product of CrO4 (2-) and NTA (m/z 290) and that of SiO4 (4-) and IDA (m/z 192) were measured. The limits of detection of the respective methods were 17 nM (0.83 ng Cr/ml) for Cr(VI) and 0.17 µM (4.8 ng Si/mL) for SiO4 (4-) .

Higher radical scavenging activities of polyphenolic antioxidants can be ascribed to chemical reactions following their oxidation.

Radical scavenging activities of 34 natural antioxidants were investigated from an electrochemical viewpoint. While the correlation of the oxidation potentials with their DPPH radical scavenging activities (represented by EC(50)) was not high (the correlation coefficient, r=0.73), the number of electrons n required for oxidation of an antioxidant, being obtained by continuous flow-column electrolysis with a slower flow rate (0.05 ml min(-1)), did show a good correlation with EC(50) (1/EC(50)=1.67n+0.50 with r=0.94). The n values of most polyphenols were increased with a decrease in the flow rate, while those of nonpolyphenols were invariant. This suggests that a slower subsequent chemical reaction(s) should be involved in the oxidation of polyphenols, whose higher radical scavenging activities seem to be ascribed to the chemical reactions. In this study, we have proposed a possible mechanism for the oxidation of polyphenols, in which the oxidizable -OH moieties are reproduced through an oxidative dimerization (or more highly polymerization).

Effects of fullerene substituents on structure and photoelectrochemical properties of fullerene nanoclusters electrophoretically deposited on nanostructured SnO2 electrodes.

Two kinds of fullerene derivatives have been designed to examine the effect of the fullerene substituents on the structure and photoelectrochemical properties of fullerene clusters electrophoretically deposited on nanostructured SnO(2) electrodes. The cluster sizes increase and the incident photon-to-current efficiencies decrease with introduction of large substituents into C(60). The trend for photocurrent generation efficiency as well as surface morphology on the electrode can be explained by the steric bulkiness around the C(60) molecules. A C(60) molecule with two alkoxy chains is suggested to give a bilayer vesicle structure, irrespective of the hydrophobic nature of both the C(60) and alkoxy chain moieties. Such information will be valuable for the design of photoactive molecules, which are fabricated onto electrode surfaces to exhibit high energy conversion efficiency.

Hydrogen bonding effects on the surface structure and photoelectrochemical properties of nanostructured SnO2 electrodes modified with porphyrin and fullerene composites.

Hydrogen bonding effects on surface structure, photophysical properties, and photoelectrochemistry have been examined in a mixed film of porphyrin and fullerene composites with and without hydrogen bonding on indium tin oxide and nanostructured SnO2 electrodes. The nanostructured SnO2 electrodes modified with the mixed films of porphyrin and fullerene composites with hydrogen bonding exhibited efficient photocurrent generation compared to the reference systems without hydrogen bonding. Atomic force microscopy, infrared reflection absorption, and ultraviolet-visible absorption spectroscopies and time-resolved fluorescence lifetime and transient absorption spectroscopic measurements disclosed the relationship between the surface structure and photophysical and photoelectrochemical properties relating to the formation of hydrogen bonding between the porphyrins and/or the C60 moieties in the films on the electrode surface. These results show that hydrogen bonding is a highly promising methodology for the fabrication of donor and acceptor composites on nanostructured semiconducting electrodes, which exhibit high photoelectrochemical properties.

Characteristics of a liquid/liquid optical waveguide using sheath flow and its application to detect molecules at a liquid/liquid interface.

The formation conditions and characteristics of a liquid/liquid optical waveguide (LLW) were studied using a two-phase sheath flow, where the inner organic phase flow acted as the core and the outer aqueous flow acted as the clad. In immiscible solvent systems, i.e., toluene/water and diethyl ether/water systems, the LLWs were formed in the range of higher than ca. 600 of the Reynolds number (Re), where the linear velocity of the organic solvent was much higher than that of the aqueous solution. On the other hand, in a miscible solvent system, i.e., a tetrahydrofuran/water system, a stable LLW was formed in the range of a much lower Re than in immiscible systems. Moreover, the molecules at the toluene/water interface of the LLW were observed with both fluorescence and absorbance measurement systems. In particular, the change in the fluorescence spectrum of 1-anilino-8-naphthalenesulfonate (ANS) at the interface within 1 ms was observed by this method, indicating the usefulness of the LLW for a fast kinetic study of a liquid/liquid interface.

Electrospray ionization mass spectrometry for the quantification of inorganic cations and anions.

Recent studies from our laboratory on electrospray ionization mass spectrometry (ESI-MS) for the quantification of inorganic cations and anions are reviewed. Metal ions were determined by ESI-MS in negative-ion mode as monovalent negative ions of their aminopolycarboxylate (APC) complexes, where excess amounts of the APC agents were added to sample solutions. Among the APCs studied, we found trans-1,2-diaminocyclohexane-N,N,N',N'-tetraacetic acid (CyDTA, the chemical forms in a complex were expressed as H(n)cydta(n-4)) as the best chelating agent. A size exclusion column was used for on-line separation of the metal-APC complexes from matrix salts in samples. Total amounts of Al, Ni, Cu, Zn, and Pb in the biological certified reference materials (CRM), Olive Leaves (BCR-062) and Plankton (BCR-414), and in a soil CRM (JSAC-0401) were successfully determined by the proposed method. Halide ions (X(-) = F(-), Cl(-), Br(-) and I(-)) and cyanide (CN(-)) were determined by ESI-MS based on the formation of ternary complexes of metals, chelating agents and the analyte anions. Negative ions of the ternary complexes of group 13 elements, nitrilotriacetic acid (NTA, H(n)nta(n-3)), and halides, i.e., [AlF(nta)](-) for F(-), and [InX(nta)](-) for other halides, were measured; the limits of detection (LODs) were 10 nmol dm(-3) for F(-), 0.31 µmol dm(-3) for Cl(-), 3.8 nmol dm(-3) for Br(-), and 1.6 nmol dm(-3) for I(-), respectively. In the case of CN(-), an LOD of 20 nmol dm(-3) was obtained based on measurements of the ternary complex of Cu(II), CN(-) and 4-(2-pyridylazo)resorcinol (PAR, Hnpar(n-2)), i.e., [(63)Cu(II)(CN)(par)](-) (m/z 302). Moreover, quantitative methods for Cr(VI) and Cr(III) by ESI-MS were developed, where HCrO4(-) (m/z 117) for Cr(VI) and [Cr(III)(cydta)](-) for Cr(III) were used for measurements.

Correlation of redox potentials and inhibitory effects on Epstein-Barr virus activation of naphthoquinones.

As a continuation of our studies using natural and synthetic products as cancer chemopreventive agents, we examined the standard redox potentials of some naphthoquinones in phosphate buffer at pH 7.2 by means of cyclic voltammetry. A definite correlation has been found between the redox potentials and the inhibitory effects of the naphthoquinones on Epstein-Barr virus early antigen activation. It has been further shown that the correlation can be enhanced by introducing an electronic property, i.e. the atomic charges at the C(4) and O(10) atoms in the quinone skeleton ring as additional parameters.