Exchange biasing of magnetoelectric composites.

Magnetoelectric composite materials are promising candidates for highly sensitive magnetic-field sensors. However, the composites showing the highest reported magnetoelectric coefficients require the presence of external d.c. magnetic bias fields, which is detrimental to their use as sensitive high-resolution magnetic-field sensors. Here, we report magnetoelectric composite materials that instead rely on intrinsic magnetic fields arising from exchange bias in the device. Thin-film magnetoelectric two-two composites were fabricated by magnetron sputtering on silicon-cantilever substrates. The composites consist of piezoelectric AlN and multilayers with the sequence Ta/Cu/Mn(70)Ir(30)/Fe(50)Co(50) or Ta/Cu/Mn(70)Ir(30)/Fe(70.2)Co(7.8)Si(12)B(10) serving as the magnetostrictive component. The thickness of the ferromagnetic layers and angle dependency of the exchange bias field are used to adjust the shift of the magnetostriction curve in such a way that the maximum piezomagnetic coefficient occurs at zero magnetic bias field. These self-biased composites show high sensitivity to a.c. magnetic fields with a maximum magnetoelectric coefficient of 96 V cm(-1) Oe(-1) at mechanical resonance.

Crystallography at the nanoscale: planar defects in ZnO nanospikes.

The examination of anisotropic nanostructures, such as wires, platelets or spikes, inside a transmission electron microscope is normally performed only in plan view. However, intrinsic defects such as growth twin interfaces could occasionally be concealed from direct observation for geometric reasons, leading to superposition. This article presents the shadow-focused ion-beam technique to prepare multiple electron-beam-transparent cross-section specimens of ZnO nanospikes, via a procedure which could be readily extended to other anisotropic structures. In contrast with plan-view data of the same nanospikes, here the viewing direction allows the examination of defects without superposition. By this method, the coexistence of two twin configurations inside the wurtzite-type structure is observed, namely and , which were not identified during the plan-view observations owing to superposition of the domains. The defect arrangement could be the result of coalescence twinning of crystalline nuclei formed on the partially molten Zn substrate during the flame-transport synthesis. Three-dimensional defect models of the twin interface structures have been derived and are correlated with the plan-view investigations by simulation.

Atomic structure and crystallography of joints in SnO2 nanowire networks.

Joints of three-dimensional (3D) rutile-type (r) tin dioxide (SnO2) nanowire networks, produced by the flame transport synthesis (FTS), are formed by coherent twin boundaries at (101)r serving for the interpenetration of the nanowires. Transmission electron microscopy (TEM) methods, i.e. high resolution and (precession) electron diffraction (PED), were utilized to collect information of the atomic interface structure along the edge-on zone axes [010]r, [111]r and superposition directions [001]r, [101]r. A model of the twin boundary is generated by a supercell approach, serving as base for simulations of all given real and reciprocal space data as for the elaboration of three-dimensional, i.e. relrod and higher order Laue zones (HOLZ), contributions to the intensity distribution of PED patterns. Confirmed by the comparison of simulated and experimental findings, details of the structural distortion at the twin boundary can be demonstrated.

Piezoresistive Response of Quasi-One-Dimensional ZnO Nanowires Using an in Situ Electromechanical Device.

Quasi-one-dimensional structures from metal oxides have shown remarkable potentials with regard to their applicability in advanced technologies ranging from ultraresponsive nanoelectronic devices to advanced healthcare tools. Particularly due to the piezoresistive effects, zinc oxide (ZnO)-based nanowires showed outstanding performance in a large number of applications, including energy harvesting, flexible electronics, smart sensors, etc. In the present work, we demonstrate the versatile crystal engineering of ZnO nano- and microwires (up to centimeter length scales) by a simple flame transport process. To investigate the piezoresistive properties, particular ZnO nanowires were integrated on an electrical push-to-pull device, which enables the application of tensile strain and measurement of in situ electrical properties. The results from ZnO nanowires revealed a periodic variation in stress with respect to the applied periodic potential, which has been discussed in terms of defect relaxations.

Direct Growth of Freestanding ZnO Tetrapod Networks for Multifunctional Applications in Photocatalysis, UV Photodetection, and Gas Sensing.

Growth of freestanding nano- and microstructures with complex morphologies is a highly desired aspect for real applications of nanoscale materials in various technologies. Zinc oxide tetrapods (ZnO-T), which exhibit three-dimensional (3D) shapes, are of major importance from a technological applications point of view, and thus efficient techniques for growth of different varieties of tetrapod-based networks are demanded. Here, we demonstrate the versatile and single-step synthesis of ZnO-T with different arm morphologies by a simple flame transport synthesis (FTS) approach, forming a network. Morphological evolutions and structural intactness of these tetrapods have been investigated in detail by scanning electron microscopy, X-ray diffraction, and micro-Raman measurements. For a deeper understanding of the crystallinity, detailed high-resolution transmission electron microscopic studies on a typical ZnO tetrapod structure are presented. The involved growth mechanism for ZnO tetrapods with various arm morphologies is discussed with respect to variations in experimental conditions. These ZnO-T have been utilized for photocatalytic degradation and nanosensing applications. The photocatalytic activities of these ZnO-T with different arm morphologies forming networks have been investigated through the photocatalytic decolorization of a methylene blue (MB) solution under UV light illumination at ambient temperature. The results show that these ZnO-T exhibit strong photocatalytic activities against MB and its complete degradation can be achieved in very short time. In another application, a prototype of nanoelectronic sensing device has been built from these ZnO-T interconnected networks and accordingly utilized for UV detection and H2 gas sensing. The fabricated device structures showed excellent sensing behaviors for promising practical applications. The involved sensing mechanisms with respect to UV photons and H2 gas are discussed in detail. We consider that such multifunctional nanodevices based on ZnO tetrapod interconnected networks will be of interest for various advanced applications.