Comparative Analysis of Ethylene/Diene Copolymerization and Ethylene/Propylene/Diene Terpolymerization Using Ansa-Zirconocene Catalyst with Alkylaluminum/Borate Activator: The Effect of Conjugated and Nonconjugated Dienes on Catalytic Behavior and Polymer Microstructure.

The copolymerization of ethylene‒diene conjugates (butadiene (BD), isoprene (IP) and nonconjugates (5-ethylidene-2-norbornene (ENB), vinyl norbornene VNB, 4-vinylcyclohexene (VCH) and 1, 4-hexadiene (HD)), and terpolymerization of ethylene-propylene-diene conjugates (BD, IP) and nonconjugates (ENB, VNB, VCH and HD) using two traditional catalysts of C2-symmetric metallocene-silylene-bridged rac-Me2Si(2-Me-4-Ph-Ind)2ZrCl2 (complex A) and ethylene-bridged rac-Et(Ind)2ZrCl2 (complex B)-with a [Ph3C][B(C6F5)4] borate/TIBA co-catalyst, were intensively studied. Compared to that in the copolymerization of ethylene diene, the catalytic activity was more significant in E/P/diene terpolymerization. We obtained a maximum yield of both metallocene catalysts with conjugated diene between 3.00 × 106 g/molMt·h and 5.00 × 106 g/molMt·h. ENB had the highest deactivation impact on complex A, and HD had the most substantial deactivation effect on complex B. A 1H NMR study suggests that dienes were incorporated into the co/ter polymers' backbone through regioselectivity. ENB and VNB, inserted by the edo double bond, left the ethylidene double bond intact, so VCH had an exo double bond. Complex A's methyl and phenyl groups rendered it structurally stable and exhibited a dihedral angle greater than that of complex B, resulting in 1, 2 isoprene insertion higher than 1, 4 isoprene that is usually incapable of polymerization coordination. High efficiency in terms of co- and ter- monomer incorporation with higher molecular weight was found for complex 1. The rate of incorporation of ethylene and propylene in the terpolymer backbone structure may also be altered by the conjugated and nonconjugated dienes. 13C-NMR, 1H-NMR, and GPC techniques were used to characterize the polymers obtained.

Dissolution of Danazol Amorphous Solid Dispersions: Supersaturation and Phase Behavior as a Function of Drug Loading and Polymer Type.

Amorphous solid dispersions (ASDs) are of great interest as enabling formulations because of their ability to increase the bioavailability of poorly soluble drugs. However, the dissolution of these formulations under nonsink dissolution conditions results in highly supersaturated drug solutions that can undergo different types of phase transitions. The purpose of this study was to characterize the phase behavior of solutions resulting from the dissolution of model ASDs as well as the degree of supersaturation attained. Danazol was chosen as a poorly water-soluble model drug, and three polymers were used to form the dispersions: polyvinylpyrrolidone (PVP), hydroxypropylmethyl cellulose (HPMC), and hydroxypropylmethyl cellulose acetate succinate (HPMCAS). Dissolution studies were carried out under nonsink conditions, and solution phase behavior was characterized using several orthogonal techniques. It was found that liquid-liquid phase separation (LLPS) occurred following dissolution and prior to crystallization for most of the dispersions. Using flux measurements, it was further observed that the maximum attainable supersaturation following dissolution was equivalent to the amorphous solubility. The dissolution of the ASDs led to sustained supersaturation, the duration of which varied depending on the drug loading and the type of polymer used in the formulation. The overall supersaturation profile observed thus depended on a complex interplay between dissolution rate, polymer type, drug loading, and the kinetics of crystallization.

Sodium Lauryl Sulfate Competitively Interacts with HPMC-AS and Consequently Reduces Oral Bioavailability of Posaconazole/HPMC-AS Amorphous Solid Dispersion.

Sodium lauryl sulfate (SLS), as an effective surfactant, is often used as a solubilizer and/or wetting agent in various dosage forms for the purpose of improving the solubility and dissolution of lipophilic, poorly water-soluble drugs. This study aims to understand the impact of SLS on the solution behavior and bioavailability of hypromellose acetate succinate (HPMC-AS)-based posaconazole (PSZ) ASDs, and to identify the underlying mechanisms governing the optimal oral bioavailability of ASDs when surfactants such as SLS are used in combination. Fluorescence spectroscopy and optical microscopy showed that "oil-out" or "liquid-liquid phase separation (LLPS)" occurred in the supersaturated PSZ solution once drug concentration surpassed ∼12 µg/mL, which caused the formation of drug-rich oily droplets with initial size of ∼300-400 nm. Although FT-IR study demonstrated the existence of specific interactions between PSZ and HPMC-AS in the solid state, predissolved HPMC-AS was unable to delay LLPS of the supersaturated PSZ solution and PSZ-rich amorphous precipitates with ∼16-18% HPMC-AS were formed within 10 min. The coprecipitated HPMC-AS was found to be able to significantly delay the crystallization of PSZ in the PSZ-rich amorphous phase from less than 10 min to more than 4 h, yet coexistent SLS was able to negate this crystallization inhibition effect of HPMC-AS in the PSZ-rich amorphous precipitates and cause fast PSZ crystallization within 30 min. 2D-NOESY and the CMC/CAC results demonstrated that SLS could assemble around HPMC-AS and competitively interact with HPMC-AS in the solution, thus prevent HPMC-AS from acting as an effective crystallization inhibitor. In a crossover dog PK study, this finding was found to be correlating well with the in vivo bioavailability of PSZ ASDs formulated with or without SLS. The SLS containing PSZ ASD formulation demonstrated an in vivo bioavailability ∼30% of that without SLS, despite the apparently better in vitro dissolution, which only compared the dissolved drug in solution, a small fraction of the total PSZ dose. We conclude that the bioavailability of ASDs is highly dependent on the molecular interactions between drug, surfactant, and polymer, not only in the solution phase but also in the drug-rich "oily" phase caused by supersaturation.

Characterization of Supersaturated Danazol Solutions - Impact of Polymers on Solution Properties and Phase Transitions.

PURPOSE: Excipients are essential for solubility enhancing formulations. Hence it is important to understand how additives impact key solution properties, particularly when supersaturated solutions are generated by dissolution of the solubility enhancing formulation. Herein, the impact of different concentrations of dissolved polymers on the thermodynamic and kinetic properties of supersaturated solutions of danazol were investigated. METHODS: A variety of experimental techniques was used, including nanoparticle tracking analysis, fluorescence and ultraviolet spectroscopy and flux measurements to characterize the solution phase behavior. RESULTS: Neither the crystalline nor amorphous solubility of danazol was impacted by common amorphous solid dispersion polymers, polyvinylpyrrolidone, hydroxypropylmethyl cellulose (HPMC) or HPMC-acetate succinate. Consequently, the maximum membrane transport rate was limited only by the amorphous solubility, and not by the presence of the polymers. The polymers were able to inhibit crystallization to some extent at concentrations as low as 1 µg/mL, with the maximum effectiveness being reached at 10 µg/mL. Aqueous danazol solutions formed a drug-rich phase with a mean size of 250 nm when the concentration exceeded the amorphous solubility, and the polymers modified the surface properties of this drug-rich phase. CONCLUSIONS: The phase behavior of supersaturated solutions is complex and the kinetics of phase transformations can be substantially modified by polymeric additives present at low concentrations. However, fortunately, these additives do not appear to impact the bulk thermodynamic properties of the solution, thus enabling supersaturated solutions, which provide enhanced membrane transport relative to saturated solutions to be generated.

Initial Drug Dissolution from Amorphous Solid Dispersions Controlled by Polymer Dissolution and Drug-Polymer Interaction.

PURPOSE: To identify the key formulation factors controlling the initial drug and polymer dissolution rates from an amorphous solid dispersion (ASD). METHODS: Ketoconazole (KTZ) ASDs using PVP, PVP-VA, HMPC, or HPMC-AS as polymeric matrix were prepared. For each drug-polymer system, two types of formulations with the same composition were prepared: 1. Spray dried dispersion (SDD) that is homogenous at molecular level, 2. Physical blend of SDD (80% drug loading) and pure polymer (SDD-PB) that is homogenous only at powder level. Flory-Huggins interaction parameters (χ) between KTZ and the four polymers were obtained by Flory-Huggins model fitting. Solution (13)C NMR and FT-IR were conducted to investigate the specific drug-polymer interaction in the solution and solid state, respectively. Intrinsic dissolution of both the drug and the polymer from ASDs were studied using a Higuchi style intrinsic dissolution apparatus. PXRD and confocal Raman microscopy were used to confirm the absence of drug crystallinity on the tablet surface before and after dissolution study. RESULTS: In solid state, KTZ is completely miscible with PVP, PVP-VA, or HPMC-AS, demonstrated by the negative χ values of -0.36, -0.46, -1.68, respectively; while is poorly miscible with HPMC shown by a positive χ value of 0.23. According to solution (13)C NMR and FT-IR studies, KTZ interacts with HPMC-AS strongly through H-bonding and dipole induced interaction; with PVPs and PVP-VA moderately through dipole-induced interactions; and with HPMC weakly without detectable attractive interaction. Furthermore, the "apparent" strength of drug-polymer interaction, measured by the extent of peak shift on NMR or FT-IR spectra, increases with the increasing number of interacting drug-polymer pairs. For ASDs with the presence of considerable drug-polymer interactions, such as KTZ/PVPs, KTZ/PVP-VA, or KTZ /HPMC-AS systems, drug released at the same rate as the polymer when intimate drug-polymer mixing was ensured (i.e., the SDD systems); while drug released much slower than the polymer when molecular level mixing or drug-polymer interaction was absent (SDD-PB systems). For ASDs without drug-polymer interaction (i.e., KTZ/HPMC systems), the mixing homogeneity had little impact on the release rate of either the drug or the polymer thus SDD and SDD-PB demonstrated the same drug or polymer release rate, while the drug released slowly and independently of polymer release. CONCLUSIONS: The initial drug release from an ASD was controlled by 1) the polymer release rate; 2) the strength of drug-polymer interaction, including the intrinsic interaction caused by the chemistry of the drug and the polymer (measured by the χ value), as well as that the apparent interaction caused by the drug-polymer ratio (measure by the extent of peak shift on spectroscopic analysis); and 3) the level of mixing homogeneity between the drug and polymer. In summary, the selection of polymer, drug-polymer ratio, and ASD processing conditions have profound impacts on the dissolution behavior of ASDs. Graphical Abstract Relationship between initial drug and polymer dissolution rates from amorphous solid dispersions with different mixing uniformity and drug-polymer interactions.

Drug-polymer-water interaction and its implication for the dissolution performance of amorphous solid dispersions.

The in vitro dissolution mechanism of an amorphous solid dispersion (ASD) remains elusive and highly individualized, yet rational design of ASDs with optimal performance and prediction of their in vitro/in vivo performance are very much desirable in the pharmaceutical industry. To this end, we carried out comprehensive investigation of various ASD systems of griseofulvin, felodipine, and ketoconazole, in PVP-VA or HPMC-AS at different drug loading. Physiochemical properties and processes related to drug-polymer-water interaction, including the drug crystallization tendency in aqueous medium, drug-polymer interaction before and after moisture exposure, supersaturation of drug in the presence of polymer, polymer dissolution kinetics, etc., were characterized and correlated with the dissolution performance of ASDs at different dose and different drug/polymer ratio. It was observed that ketoconazole/HPMC-AS ASD outperformed all other ASDs in various dissolution conditions, which was attributed to the drug's low crystallization tendency, the strong ketoconazole/HPMC-AS interaction and the robustness of this interaction against water disruption, the dissolution rate and the availability of HPMC-AS in solution, and the ability of HPMC-AS in maintaining ketoconazole supersaturation. It was demonstrated that all these properties have implications for the dissolution performance of various ASD systems, and further quantification of them could be used as potential predictors for in vitro dissolution of ASDs. For all ASDs investigated, HPMC-AS systems performed better than, or at least comparably with, their PVP-VA counterparts, regardless of the drug loading or dose. This observation cannot be solely attributed to the ability of HPMC-AS in maintaining drug supersaturation. We also conclude that, for fast crystallizers without strong drug-polymer interaction, the only feasible option to improve dissolution might be to lower the dose and the drug loading in the ASD. In this study, we implemented an ASD/water Flory-Huggins parameter plot, which might assist in revealing the physical nature of the drug-polymer interaction. We also introduced supersaturation parameter and dissolution performance parameter as two quantitative measurements to compare the abilities of polymers in maintaining drug supersaturation, and the dissolution performance of various solid dispersions, respectively.

Mitigation of Adverse Clinical Events of a Narrow Target Therapeutic Index Compound through Modified Release Formulation Design: An in Vitro, in Vivo, in Silico, and Clinical Pharmacokinetic Analysis.

BMS-914392 is a tricyclic pyranoquinoline BCS class 2 weak base that demonstrates high solubility in low pH environments. Initial clinical studies indicated that rapid release of high dose BMS-914392 led to transient adverse events associated with peak plasma concentrations. A modified release (MR) formulation strategy was proposed to suppress the peak blood concentration and maintain total exposure to overcome the adverse effects. Three modified release prototype formulations were developed and tested via a USP 3 dissolution method to verify that each formulation can effectively slow the release of BMS-914392. A pharmacokinetic (PK) absorption model was employed to guide the formulation development and selection. Simulations showed good agreement with plasma levels measured after oral dosing in dogs. Identification of key formulation factors to achieve release rates suitable for blunting peak blood levels without diminishing exposure were achieved through combined preclinical data and use of GastroPlus simulations. PK absorption model refinements based on phase 1 data, dog pharmacokinetic results, and in vitro data provided reliable predictions of human absorption profiles and variability in patients. All three prototype formulations demonstrated lower maximum plasma concentrations of BMS-914392 and maintained satisfactory relative bioavailability. Both the PK absorption model and subsequent clinical data indicated that an acidified hydrophilic matrix MR formulation had the greatest potential to reduce the incidence of adverse events and showed the best exposure profile in fasted state healthy subjects with and without famotidine coadministration. The risk based development process achieved successful screening and selection of a suitable modified release formulation to enable clinical efficacy trials.

Decoupling the contribution of surface energy and surface area on the cohesion of pharmaceutical powders.

PURPOSE: Surface area and surface energy of pharmaceutical powders are affected by milling and may influence formulation, performance and handling. This study aims to decouple the contribution of surface area and surface energy, and to quantify each of these factors, on cohesion. METHODS: Mefenamic acid was processed by cryogenic milling. Surface energy heterogeneity was determined using a Surface Energy Analyser (SEA) and cohesion measured using a uniaxial compression test. To decouple the surface area and surface energy contributions, milled mefenamic acid was "normalised" by silanisation with methyl groups, confirmed using X-ray Photoelectron Spectroscopy. RESULTS: Both dispersive and acid-base surface energies were found to increase with increasing milling time. Cohesion was also found to increase with increasing milling time. Silanised mefenamic acid possessed a homogenous surface with a surface energy of 33.1 ± 1.4 mJ/m(2) , for all milled samples. The cohesion for silanised mefenamic acid was greatly reduced, and the difference in the cohesion can be attributed solely to the increase in surface area. For mefenamic acid, the contribution from surface energy and surface area on cohesion was quantified to be 57% and 43%, respectively. CONCLUSIONS: Here, we report an approach for decoupling and quantifying the contribution from surface area and surface energy on powder cohesion.

Impact of polymers on the precipitation behavior of highly supersaturated aqueous danazol solutions.

The phase behavior of supersaturated solutions of a relatively hydrophobic drug, danazol, was studied in the absence and presence of polymeric additives. To differentiate between phase separation to a noncrystalline phase and phase separation to a crystalline phase, an environmentally sensitive fluorescent probe was employed. Induction times for crystallization in the presence and absence of polymeric additives were studied using a combination of ultraviolet and fluorescence spectroscopy. It was found that, when danazol was added to aqueous media at concentrations above the amorphous solubility, liquid-liquid phase separation was briefly observed prior to crystallization, resulting in a short-lived, drug-rich noncrystalline danazol phase with an initial size of around 500 nm. The addition of polymers was found to greatly extend the lifetime of the supersaturated two phase system, delaying the onset of crystallization from a few minutes to a few hours. Below a certain threshold danazol concentration, found to represent the amorphous solubility, only crystallization was observed. Thus, although the addition of polymers was unable to prevent danazol from precipitating once a threshold concentration was exceeded, they did inhibit crystallization, leading to a solution with prolonged supersaturation. This observation highlights the need to determine the structure of the precipitating phase, since it is linked to the resultant solution concentration time profile.

Focal EEG slowing and chorea: electroclinical clues to the diagnosis of anti-NMDAR encephalitis.

Variations in clinical presentation can lead to delays in the diagnosis and initiation of treatment of anti-N-methyl-D-aspartate receptor encephalitis. Most patients have an EEG study performed early in the course of their illness. Although not specific, there may be clues in the electroclinical features that should alert clinicians and electroencephalographers to the possibility of this diagnosis. This case is a reminder that anti- anti-N-methyl-D-aspartate receptor encephalitis may present initially with a movement disorder as the sole symptom, without features of an encephalopathy. In addition, it adds to the growing body of evidence that recognition of certain electroclinical clues may shorten the time to diagnosis. [Published with video sequence].

A method to evaluate the effect of contact with excipients on the surface crystallization of amorphous drugs.

Amorphous drugs are used to improve the solubility, dissolution, and bioavailability of drugs. However, these metastable forms of drugs can transform into more stable, less soluble, crystalline counterparts. This study reports a method for evaluating the effect of commonly used excipients on the surface crystallization of amorphous drugs and its application to two model amorphous compounds, nifedipine and indomethacin. In this method, amorphous samples of the drugs were covered by excipients and stored in controlled environments. An inverted light microscope was used to measure in real time the rates of surface crystal nucleation and growth. For nifedipine, vacuum-dried microcrystalline cellulose and lactose monohydrate increased the nucleation rate of the ß polymorph from two to five times when samples were stored in a desiccator, while D-mannitol and magnesium stearate increased the nucleation rate 50 times. At 50% relative humidity, the nucleation rates were further increased, suggesting that moisture played an important role in the crystallization caused by the excipients. The effect of excipients on the crystal growth rate was not significant, suggesting that contact with excipients influences the physical stability of amorphous nifedipine mainly through the effect on crystal nucleation. This effect seems to be drug specific because for two polymorphs of indomethacin, no significant change in the nucleation rate was observed under the excipients.

Atrioventricular node dysfunction in pressure overload-induced heart failure-Involvement of the immune system and transcriptomic remodelling.

Heart failure is associated with atrioventricular (AV) node dysfunction, and AV node dysfunction in the setting of heart failure is associated with an increased risk of mortality and heart failure hospitalisation. This study aims to understand the causes of AV node dysfunction in heart failure by studying changes in the whole nodal transcriptome. The mouse transverse aortic constriction model of pressure overload-induced heart failure was studied; functional changes were assessed using electrocardiography and echocardiography and the transcriptome of the AV node was quantified using RNAseq. Heart failure was associated with a significant increase in the PR interval, indicating a slowing of AV node conduction and AV node dysfunction, and significant changes in 3,077 transcripts (5.6% of the transcriptome). Many systems were affected: transcripts supporting AV node conduction were downregulated and there were changes in transcripts identified by GWAS as determinants of the PR interval. In addition, there was evidence of remodelling of the sarcomere, a shift from fatty acid to glucose metabolism, remodelling of the extracellular matrix, and remodelling of the transcription and translation machinery. There was evidence of the causes of this widespread remodelling of the AV node: evidence of dysregulation of multiple intracellular signalling pathways, dysregulation of 109 protein kinases and 148 transcription factors, and an immune response with a proliferation of neutrophils, monocytes, macrophages and B lymphocytes and a dysregulation of 40 cytokines. In conclusion, inflammation and a widespread transcriptional remodelling of the AV node underlies AV node dysfunction in heart failure.

Solution behavior of PVP-VA and HPMC-AS-based amorphous solid dispersions and their bioavailability implications.

PURPOSE: To identify the mechanism behind the unexpected bio-performance of two amorphous solid dispersions: BMS-A/PVP-VA and BMS-A/HPMC-AS. METHODS: Solubility of crystalline BMS-A in PVP-VA and HPMC-AS was measured by DSC. Drug-polymer interaction parameters were obtained by Flory-Huggins model fitting. Drug dissolution kinetics of spray-dried dispersions were studied under sink and non-sink conditions. BMS-A supersaturation was studied in the presence of pre-dissolved PVP-VA and HPMC-AS. Potency and crystallinity of undissolved solid dispersions were determined by HPLC and DSC. Polymer dissolution kinetics were obtained by mass balance calculation. Bioavailability of solid dispersions was assessed in dogs. RESULTS: In solid state, both polymers are miscible with BMS-A, while PVP-VA solublizes the drug better. BMS-A dissolves similarly from both solid dispersions in vitro regardless of dissolution method, while the HPMC-AS dispersion performed much better in vivo. At the same concentration, HPMC-AS is more effective in prolonging BMS-A supersaturation; this effect was negated by the slow dissolution rate of HPMC-AS. Further study revealed that fast PVP-VA dissolution resulted in elevated drug loading in undissolved dispersions and facilitated drug recrystallization before complete release. In contrast, the hydrophobicity and slower HPMC-AS dissolution prevented BMS-A recrystallization within the HPMC-AS matrix for >24 h. CONCLUSIONS: The lower bioavailability of PVP-VA dispersion was attributed to BMS-A recrystallization within the undissolved dispersion, due to hydrophilicity and fast PVP-VA dissolution rate. Polymer selection for solid dispersion development has significant impact on in vivo performance besides physical stability.

Thermo-soil weathering and life cycle assessment of carbon black, silica and cellulose nanocrystal filled rubber nanocomposites.

Carbon black (CB) and silica (Sil) as rubber reinforcement have raised environmental concerns for being high resources consumptive and less susceptible towards biodegradability. Cellulose nanocrystal (CNC) has demonstrated great potentials for use as biodegradable nanofillers in rubber nanocomposites while evaluation of its environmental impacts with optimal end-of-life (EOL) choices is not carried out. To simulate realistic EOL, thermo-oxidative aging and soil burial aging behaviors of rubber nanocomposites with 33.3% filler were performed. The environmental weathering performance modeled with the help of life cycle assessment (LCA) illustrates increased biodegradation susceptibility with partial replacement of CB or Sil with CNC in the nanocomposites, hence promoting the environmental solutions for waste minimalization by enhancing the biodegradability potentials. In terms of LCA, the CNC incorporation contributes more to the environmental impacts in manufacturing but greatly lowers the EOL choices, by reducing the global warming potential values.

Viscoelastic Rheological Behaviors of Polypropylene and LMPP Blends.

Dynamic oscillatory shear testing is used to investigate polymeric viscoelastic behaviors. Small and large amplitude oscillatory shear tests are the canonical method for characterizing the linear and nonlinear viscoelastic behaviors of any polymeric material. With prominent and abundant work on linear viscoelastic studies, the nonlinear behavior is evasive in terms of generating infinite higher harmonics in the nonlinear regime. For this reason, intrinsic nonlinearities from large amplitude oscillatory shear (LAOS) studies have recently been used for insights on microstructural behaviors. This study is carried out for linear and nonlinear viscoelastic behavior with a main focus on LAOS of isostatic polypropylene (iPP) and relatively new low molecular weight and low modulus polypropylene-based polyolefin (LMPP) blends. The morphological results showed reduced spherulitic crystal nucleus size and increased distribution in blends with increasing LMPP. The blends showed subtle linear viscoelastic responses with strong nonlinear mechanical responses to variant strain and stress compared to pure iPP. The intracycle strain thickening and intracycle strain stiffening of high-content LMPP blends were comparatively dominant at medium strain amplitudes.

Effects of ionic liquid on cellulosic nanofiller filled natural rubber bionanocomposites.

Cellulosic nanofillers are sustainable replacements of synthetic fillers while the agglomeration limits their potentials in high-performance rubber bionanocomposites. Herein, we investigate the effects of ionic liquid (IL) on cellulose nanocrystal and cellulose nanofibril filled natural rubber (NR) compounds and vulcanizates. The results indicate that IL improves the dispersion of cellulosic nanofillers, crosslinking density of NR matrix and mechanical strength of the vulcanizates. Invesigations of viscoelastic rheological behaviors show amplitude of Payne effect faints in compounds and raises relatively in vulcanizates with the increment of cellulosic nanofillers and IL.

Large amplitude oscillatory rheology of silica and cellulose nanocrystals filled natural rubber compounds.

Nanoparticles reinforce rubbers and enhance Payne effect for the compounds experiencing large amplitude oscillatory shear deformation. Herein the effects of silica and cellulose nanocrystals on the Payne effect of natural rubber compounds are investigated by stress decomposition methods for clarifying the elastic and viscous nonlinearities varying with filler content and composition. The Payne effect is in general characterized by intercycle strain softening and shear thinning behaviors and intracycle hardening and thinning behaviors at high strain (strain rate) amplitudes while the filler influences the behaviors markedly at intermediate strain (rate) amplitudes. Especially, the addition of cellulose nanocrystals in the silica filled compounds improves the elastic nonlinearity and greatly weakens the viscous nonlinearity, providing a perspective on understanding the Payne effect for manufacturing high-performance rubber materials.

Alloxan reduces amplitude of ventricular myocyte shortening and intracellular Ca2+ without altering L-type Ca2+ current, sarcoplasmic reticulum Ca2+ content or myofilament sensitivity to Ca2+ in Wistar rats.

Alloxan is widely used to induce diabetes mellitus in experimental animals. Recent studies have provided evidence that alloxan has direct actions on cardiac muscle contraction. The aim of this study was to further investigate the mechanisms underlying the effects of alloxan on ventricular myocyte shortening and intracellular Ca(2+) transport. Amplitude of myocyte shortening was reduced in a dose-dependent manner as the concentration of alloxan was increased in the range 10(-7)-10(-4) M. Amplitude of shortening was reduced (56.8 +/- 6.6%, n = 27) by 10(-6) M alloxan and was partially reversed during a 10 min washout. Amplitude of the Ca(2+) transient was also reduced (79.7 +/- 2.9%, n = 29) by 10(-6) M alloxan. Caffeine-evoked sarcoplasmic reticulum Ca(2+) release, fractional release of Ca(2+), assessed by comparing the amplitude of electrically evoked with that of caffeine-evoked Ca(2+) transients, and fura-2-cell length trajectory during the late stages of relaxation of myocyte twitch contraction were not significantly altered by alloxan. The amplitude of L-type Ca(2+) current was not altered by alloxan. Alterations in sarcoplasmic reticulum Ca(2+) transport, myofilament sensitivity to Ca(2+), and L-type Ca(2+) current do not appear to underlie the negative inotropic effects of alloxan.

Anaplastic ependymoma with sclerotic bone metastases.

Ependymomas are glial central nervous system (CNS) tumors that arise from the ependymal layer of brain and spinal cord. These are heterogeneous group of tumors with varied histopathological features and prognosis. They frequently relapse at the primary site and may disseminate to other CNS sites. Extraneural metastases are, however, extremely rare. We present a case of ependymoma in a child with widespread metastasis to her bones, a previously unreported event.

Colloidal phase behavior of pH-responsive, amphiphilic PEGylated poly(carboxylic acid)s and effect on kinetic solubility under acidic conditions.

PEGylated poly(carboxylic acid)s, PEG-b-PCAs, were evaluated as additives for solubilized oral formulations of weakly acidic compounds. Micelles of poly(ethylene glycol)-block-poly(acrylic acid), PEG-b-PAA, and poly(ethylene glycol)-block-poly(methacrylic acid), PEG-b-PMAA, were prepared. Fluorescence spectroscopy and dynamic light scattering revealed that both polymers assemble into nanoscopic structures (< 200 nm) in acidic media and exhibit pH-sensitive colloidal phase behavior. Using a solvent evaporation technique, the block copolymers and corresponding PCA homopolymers were incorporated into PEG3350-based solid dispersions. The kinetic solubility profile of a BMS compound, BMS-A (Seq ~ 12.5 µg/mL at pH 1.1) in 0.1 N HCl was monitored as a function of polymer composition. While BMS-A precipitated rapidly in 0.1 N HCl in the absence of PEG-b-PCAs, a supersaturated level of ca. 400 µg/mL was maintained for variable lengths of time in the presence of PEG-b-PCAs. Although the kinetic solubility of BMS-A was also enhanced in the presence of the PCA homopolymers, the relative magnitude and duration of supersaturation as a function of polymer composition suggests that micellar solubilization, rather than specific interaction, contributes to enhanced solubility of BMS-A in 0.1 N HCl. Under acidic conditions, pH-responsive PEG-b-PCAs may offer the kinetic supersaturation necessary to minimize precipitation of compounds which have limited solubility in acidic milieu.