Colloids for Catalysts: A Concept for the Preparation of Superior Catalysts of Industrial Relevance.

Compared to conventional preparation methods for supported heterogeneous catalysts, the use of colloidal nanoparticles (NPs) allows for a precise control over size, size distribution, and distribution/location of the NPs on the support. However, common colloidal syntheses have restrictions that limit their applicability for industrial catalyst preparation. We present a simple, surfactant-free, and scalable preparation method for colloidal NPs to overcome these restrictions. We demonstrate how precious-metal NPs are prepared in alkaline methanol, how the particle size can be tuned, and how supported catalysts are obtained. The potential of these colloids in the preparation of improved catalysts is demonstrated by two examples from heterogeneous catalysis and electrocatalysis.

Nucleophilic fluoroalkylation/cyclization route to fluorinated phthalides.

Discribed in this article is a versatile and practical method for the synthesis of C3-perfluoroalkyl-substituted phthalides in a one-pot manner. Upon treatment of KF or triethylamine, 2-cyanobenzaldehyde reacted with (perfluoroalkyl)trimethylsilanes via nucleophilic addition and subsequent intramolecular cyclization to give perfluoroalkylphthalides in good yields.

Comparison between the fixation of peritoneal dialysis catheters to the peritoneal wall and the conventional placement technique: clinical experience and follow-up of a new implant technique for peritoneal dialysis catheters.

Peritoneal dialysis (PD) catheters often become severely dislocated, which may lead to malfunction. With the aim of preventing this complication, we have developed a simple method of fixing the catheter downwards in the peritoneal cavity (fixation technique), a technique that does not require a laparoscope. Sixteen patients were implanted using the conventional placement technique and 25 patients were implanted using the fixation technique. The location of the catheter tip was classified from grade 1 (downward, normal) to 5 (dislocated). The frequency of dislocation (defined as the extended time and/or decrease in volume when draining the PD solution) was measured for both the fixation technique and conventional placement technique. There was a significant difference in grade between the fixation technique (2.72 ± 1.01) and conventional technique (3.92 ± 1.31). The time until first dislocation was significantly different between the fixation technique (59.3 ± 48.1 days) and conventional technique (8.8 ± 14.6 days). The time until any dislocation was significantly different between the fixation technique (69.2 ± 41.9 days) and conventional technique (12.9 ± 13.7 days). Complications were not significantly different between the fixation technique and conventional technique. The fixation technique appears to be simple, safe, and useful for preventing severe dislocation and for lengthening the time until dislocation in PD patients.

Synthesis of a Mesoporous SnO2 Catalyst Support and the Effect of Its Pore Size on the Performance of Polymer Electrolyte Fuel Cells.

The aim of this study was to clarify the effectiveness and challenges of applying mesoporous tin oxide (SnO2)-based supports for Pt catalysts in the cathodes of polymer electrolyte fuel cells (PEFCs) to simultaneously achieve high performance and high durability. Recently, the focus of PEFC application in automobiles has shifted to heavy-duty vehicles (HDVs), which require high durability, high energy-conversion efficiency, and high power density. It has been reported that employing mesoporous carbon supports improves the initial performance by mitigating catalyst poisoning caused by sulfonic acid groups of the ionomer as well as by reducing the oxygen transport resistance through the Pt/ionomer interface. However, carbon materials in the cathode can degrade oxidatively during long-term operation, and more stable materials are desired. In this study, we synthesized connected mesoporous Sb-doped tin oxides (CMSbTOs) with controlled mesopore sizes in the range of 4-11 nm and tested their performance and durability as cathode catalyst supports. The CMSbTO supports exhibited higher fuel cell performance at a pore size of 7.3 nm than the solid-core SnO2-based, solid-core carbon, and mesoporous carbon supports under dry conditions, which can be attributed to the mitigation of the formation of the Pt/ionomer interface and the better proton conductivity within the mesopores even at the low-humidity conditions. In addition, the CMSbTO supports exhibited high durability under oxidative conditions. These results demonstrate the promising applicability of mesoporous tin oxide supports in PEFCs for HDVs. The remaining challenges, including the requirements for improving performance under wet conditions and stability under reductive conditions, are also discussed.

Differentiation of bone marrow-derived cells into regenerated mesothelial cells in peritoneal remodeling using a peritoneal fibrosis mouse model.

Marked thickening of the peritoneum and vasculopathy in the submesothelial compact zone have been reported in long-term peritoneal dialysis patients. Bone marrow (BM)-derived cell lines are considered to be useful tools for therapy of various diseases. To clarify the role of BM-derived cells in the peritoneal fibrosis (PF) model, we analyzed several lineages of cells in the peritoneum. BM cells from green fluorescent protein (GFP) transgenic mice were transplanted into naïve C57Bl/6 mice. Chlorhexidine gluconate (CG) was injected intraperitoneally to induce PF. Immunohistochemical analysis was performed with parietal peritoneum using anti-Sca-1 or -c-Kit and -GFP antibodies. Isolated BM cells were also transplanted into the CG-stimulated peritoneum. BM-derived cells from GFP transgenic mice appeared in the submesothelium from days 14 to 42. Both GFP- and stem cell marker-positive cells were observed in the submesothelium and on the surface. Isolated c-Kit-positive cells, transplanted into the peritoneal cavity, differentiated into mesothelial cells. In this study, we investigated whether or not BM-derived cells play a role in the repair of PF and immature cells have the potential of inducing repair of the peritoneum. The findings of this study suggest a new concept for therapy of PF.

Eutectic salt mixture-assisted sodium-vapor-induced synthesis of Pt-Ca nanoparticles, and their microstructural and electrocatalytic properties.

We have fabricated Pt-Ca nanoparticles with oxygen reduction reaction catalytic activity via a sodium vapor-induced synthesis method. Prior addition of NaCl to form a eutectic mixture of CaCl2 and NaCl facilitated the formation of intermetallic Pt2Ca nanoparticles. Pt3Mg and Pt5Sr nanoparticles also were suggested to be producible.

Femto liquid chromatography with attoliter sample separation in the extended nanospace channel.

A liquid chromatography system, comprising a separation column with a width and depth of a few hundred nanometers, was fabricated on a glass microchip (femto liquid chromatography, fLC). The size of this system was approximately 10(11) times smaller than that of a conventional LC system, the flow rate was subpicoliter/minute, and the injection volume was a few hundred attoliters. The fLC system did not require packing stationary phase and was capable of separating solutes with different molecular charges (fluorescein and sulforhodamine B) that could not be separated on a conventional LC column whose surface was covered with the same functional group as that of the column of the fLC system. The fLC system represented herein overcomes limitations of conventional chromatography separation, namely, heterogeneity of the stationary phases and eddy diffusion. Scale-down of the chromatography system brought advantages not only in reduction of sample volume but also in separation efficiency. The fLC system can analyze a very small amount of sample with high efficiency and will be useful in analyzing small samples, such as single cells and synaptic clefts. fLC greatly influences and benefits various fields such as life sciences, medicine, environmental science, and manufacturing by the improvement of separation technology.

Particle Size Effect on Platinum Dissolution: Practical Considerations for Fuel Cells.

The high costs of polymer membrane electrolyte fuel cells (PEMFCs) remain a roadblock for a competitive market with combustion engine vehicles. The PEMFC costs can be reduced by decreasing the size of Pt nanoparticles in the catalyst layer, thereby increasing the Pt dispersion and utilization. Furthermore, high-power performance loss due to O2 transport resistance is alleviated by decreasing the particle size and increasing dispersion. However, firm conclusions on how Pt particle size impacts durability remain elusive due to synthetic difficulties in exclusively varying single parameters (e.g., particle size and loading). Therefore, here the particle size of Pt nanoparticles was varied from 2.0 to 2.8 and 3.7 nm while keeping the loading constant (30 wt %) on a Vulcan support using the two-step surfactant-free toolbox method. By studying the electrochemical dissolution in situ using online inductively coupled plasma mass spectrometry (online ICP-MS), mass-specific dissolution trends are revealed and are attributed to particle-size-dependent changes in electrochemically active surface area. Such degradation trends are critical for the start/stop of PEMFCs and currently require the implementation of potential control systems in consumer vehicles. Additionally, shifts in the onset of anodic dissolution and also oxidation to more negative potentials with decreasing particle size were observed. These results indicate a similar mechanism of anodic dissolution related to place-exchange when moving from extended polycrystalline Pt to nanoparticle scales. The negative shifts in the onset as the particle size decreases highlight a practical limitation for PEMFCs during load/idle conditions: without further material improvements, which inhibit Pt dissolution, reduction in costs and improvement in high-power performance via increased Pt utilization and dispersion will not be possible by decreasing particle sizes further.

On the Preparation and Testing of Fuel Cell Catalysts Using the Thin Film Rotating Disk Electrode Method.

We present a step-by-step tutorial to prepare proton exchange membrane fuel cell (PEMFC) catalysts, consisting of Pt nanoparticles (NPs) supported on a high surface area carbon, and to test their performance in thin film rotating disk electrode (TF-RDE) measurements. The TF-RDE methodology is widely used for catalyst screening; nevertheless, the measured performance sometimes considerably differs among research groups. These uncertainties impede the advancement of new catalyst materials and, consequently, several authors discussed possible best practice methods and the importance of benchmarking. The visual tutorial highlights possible pitfalls in the TF-RDE testing of Pt/C catalysts. A synthesis and testing protocol to assess standard Pt/C catalysts is introduced that can be used together with polycrystalline Pt disks as benchmark catalysts. In particular, this study highlights how the properties of the catalyst film on the glassy carbon (GC) electrode influence the measured performance in TF-RDE testing. To obtain thin, homogeneous catalyst films, not only the catalyst preparation, but also the ink deposition and drying procedures are essential. It is demonstrated that an adjustment of the ink's pH might be necessary, and how simple control measurements can be used to check film quality. Once reproducible TF-RDE measurements are obtained, determining the Pt loading on the catalyst support (expressed as Pt wt%) and the electrochemical surface area is necessary to normalize the determined reaction rates to either surface area or Pt mass. For the surface area determination, so-called CO stripping, or the determination of the hydrogen underpotential deposition (Hupd) charge, are standard. For the determination of the Pt loading, a straightforward and cheap procedure using digestion in aqua regia with subsequent conversion of Pt(IV) to Pt(II) and UV-vis measurements is introduced.

Pharmacokinetics of calcitriol and maxacalcitol administered into peritoneal dialysate bags in peritoneal dialysis patients.

OBJECTIVES: It is well known that injection of calcitriol (CT) or maxacalcitol (OCT) is very effective in hemodialysis patients with secondary hyperparathyroidism (2HPT). However, it is difficult to use these drugs with peritoneal dialysis (PD) patients with 2HPT because these drugs must be injected two or three times per week. The objective of the present study was to evaluate the stability of physiological activities of CT and OCT in PD bags and to determine the CT or OCT dosage for intraperitoneal (IP) administration. MATERIALS AND METHODS: We added CT 1.5 microg or OCT 10 microg to Dianeal PD-2 (approximate pH = 5.0, calcium = 0.87 mmol/L; Baxter,Tokyo, Japan), Midpeliq 250 (approximate pH = 7.0, Ca = 1.0 mmol/L;Terumo Corporation, Tokyo, Japan), and Peritoliq 250 (approximate pH = 5.5, Ca = 1.0 mmol/L; Terumo Corp.). Dialysis solutions were collected from the PD bags at 0, 1, 4, 8, 12, 24, 48, and 72 hours after addition of CT and OCT. The activities of CT and OCT in the dialysis effluent were measured by radioimmunoassay. The levels of serum and effluent OCT after a single IP administration of 10 microg OCT were examined in 4 PO patients with advanced 2HPT. RESULTS: Although the levels of CT and OCT in PD bags made of polyvinyl resins decreased by 70% - 75% immediately after injection, levels in PD bags made of polypropylene resins decreased only slightly. The concentration of CT mixed into the acidic solution in glass containers was stable; the decreased concentration of CT in the PD solution might be due to adsorption onto polyvinyl resins. The maximum serum concentration after IP administration of 10 microg OCT was 750 pg/mL after 5 minutes, and remained at 500 pg/mL at 60 minutes. These results show good peritoneal transport of OCT but not rapid disappearance, unlike intravenous administration. CONCLUSIONS: If peritoneal administration of vitamin D derivatives is contemplated, it is important to select the composition of PD bag resins, type of vitamin D analog, and time lag to use when deciding the dosage of injectable vitamin D preparations, such as OCT or CT, for IP administration to PD patients. It appears that IP administration in overnight dwells might be useful for PD patients as a complementary vitamin D preparation.

Inhibitory effects of matrix metalloproteinase inhibitor ONO-4817 on morphological alterations in chlorhexidine gluconate-induced peritoneal sclerosis rats.

BACKGROUND: The activity of gelatinase, matrix metalloproteinase-2, in effluent was increased in peritoneal dialysis patients with encapsulated peritoneal sclerosis (EPS) and in chlorhexidine gluconate-induced peritoneal sclerosing (PS) animal models. The objective of the present study was to investigate the effect of matrix metalloproteinase inhibitor (ONO-4817), an anticancer agent with anti-angiogenesis and anti-infiltration effects, on the development of peritoneal fibrosis in chlorhexidine gluconate-induced PS rats. METHODS: Forty-five Sprague-Dawley (S-D) rats were intraperitoneally injected with saline as control (n = 15) or with chlorhexidine gluconate (CH) (1.5 ml/100 g) in the CH group (n = 15). ONO-4817 (5 mg/rat) was administered intravenously to CH rats (the ONO-4817 group, n = 15) from initiation to the end of the study. After 22 days of ONO-4817 administration, the rats were sacrificed and the parietal peritoneum was harvested. The gene expressions of transforming growth factor-beta (TGF-beta), alpha-smooth muscle actin (alpha-SMA) and type I collagen in the peritoneum were analysed by the reverse transcription-polymerase chain reaction (RT-PCR). Peritoneal tissues were also evaluated immunohistologically. RESULTS: ONO-4817 significantly inhibited thickening of the submesothelial layer and accumulation of type I collagen in the peritoneum. ONO-4817 also prevented increases of the number of macrophages and blood vessels. The expressions of TGF-beta, alpha-SMA and type I collagen in the peritoneum were markedly suppressed in ONO-4817-treated rats. CONCLUSION: It appears that the administration of the MMP inhibitor ONO-4817 might be a new approach to the amelioration of PS.