Photobiomodulation therapy reduces postoperative pain after third molar extractions: A randomized clinical trial.

BACKGROUND: To assess the efficacy of PBMT on reducing postoperative pain scores in patients submitted to third molar extractions. MATERIAL AND METHODS: A randomized controlled trial (ReBEC:RBR-94BCKZ) was designed according to the SPIRIT and followed the CONSORT. Patients were randomly allocated according to control or PBMT groups. PBMT consisted of the application of GaAlAs laser (808nm;50mW) applied in six points (1.23 min;11 J/cm2) after extraction. Pain scores were assessed using the Visual Analogue Scale (VAS) in millimeters evaluated after 6 (T6), 24 (T24), and 48 (T48) hours. The Wilcoxon Mann-Whitney test was used to check for possible associations between VAS scores and treatment groups. RESULTS: A total of 101 third molar extractions were performed in 44 patients. The mean age was 28 years old(SD±11.54). Comparing control and intervention, PBMT group showed a significant effect on the reduction of postoperative pain at T6(mean VAS=0.9; C.I:0.63-1.16) compared to control (mean VAS=2.5;C.I:2.1-2.88)(p<0.001). The same statistically significant effect on the reduction of postoperative pain was observed at T24 (PBMT mean VAS=0.72;C.I:0.51-0.93; control mean VAS=2.86;C.I:2.40-3.31;p<0.001) and T48 (PBMT mean VAS=0.64;C.I:0.36-0.92; control mean VAS=2.86;C.I:2.37-3.34;p<0.001). CONCLUSIONS: PBMT significantly reduce the postoperative pain scores when assessed 6, 24, and 48 hours after third molar extractions.

Characterization of Contemporary Conventional, Bulk-fill, and Self-adhesive Resin Composite Materials.

OBJECTIVE: To evaluate the physical and biological properties of different types of flowable resin composites and their bonding ability to dentin, comparing the performance of self-adhesive and bulk-fill materials with a conventional control. METHODS AND MATERIALS: Four flowable resin composites were tested: two self-adhesive (Y-flow [SA_YF]; and Dyad Flow [SA_DF]); one bulk-fill (Filtek Bulk Fill Flow [BF]); and one conventional composite (Opallis Flow [OF]). The microshear bond strength (µSBS) to dentin (bovine samples) was investigated at 24 hours and 6 months of storage. The materials were also characterized by degree of conversion, cross-link density, water contact angle, color stability, and cell viability (ISO 10993-5/2009) analyses. Data were analyzed using Analysis of Variance and Tukey tests (α=0.05). RESULTS: The µSBS values were higher for control specimens at 24 hours, whereas the resin-dentin bonds were similarly distributed among the groups after aging. Adhesive failure was the most frequent pattern observed at both time intervals. SA_YF was the only material that increased the bond strength over time. Degree of conversion increased in the following order: SA_YF (28.6±1.4%) < BF (49.7±0.8%) < OF (60.0±2.0%) = SA_DF (63.6±2.3%). Cross-link density was similar among all materials. The self-adhesive composites were more hydrophilic than the other types, with BF showing the lowest water contact angle and the greatest color alteration. All resin composites had a biocompatible behavior. CONCLUSION: Chemical composition appeared to be an influential factor affecting the physico-mechanical and biological behavior of the materials tested.

Bonding of Adhesive Luting Agents to Caries-affected Dentin Induced by a Microcosm Biofilm Model.

OBJECTIVES: To evaluate the bond strength of adhesive luting agents applied to caries-affected dentin (CAD). METHODS: Thirty-six noncarious human third molars were abraded to expose an occlusal dentin surface. Caries lesions were induced in half of the samples using a microcosm biofilm model. Biofilm was cultivated under an anaerobic atmosphere for 14 days in a medium enriched with mucin. The same medium containing 1% sucrose was alternated for 4 hours per day. Cylinders of resin cement (RelyX ARC, RelyX U200, or BisCem) were built up over the dentin substrate and submitted to shear bond load. The samples were then longitudinally sectioned. The hardness and elastic modulus of dentin were measured at different depths from the occlusal surface. A three-dimensional finite element simulation was performed to analyze the residual stress distribution during the shear bond strength test. Bond strength data were analyzed by two-way analysis of variance (ANOVA) and hardness and elastic modulus by split-plot ANOVA. Multiple comparisons were performed with the SNK test (α=0.05). RESULTS: For all cements, the highest bond strengths were observed in sound dentin. Relyx ARC bond strength was similar to that of RelyX U200 for both substrates; BisCem had the lowest values. CAD had lower hardness (above a depth of 100 µm) and elastic modulus (above a depth of 150 µm) values than sound dentin. Stress distribution during the bond strength test was similar under all experimental conditions. CONCLUSION: Impairment of the mechanical properties of dentin promoted by carious lesions reduced the bond strength of adhesive luting agents.