Interface Engineering Enables Wide-Temperature Li-Ion Storage in Commercial Silicon-Based Anodes.

Silicon-based materials have been considered potential anode materials for next-generation lithium-ion batteries based on their high theoretical capacity and low working voltage. However, side reactions at the Si/electrolyte interface bring annoying issues like low Coulombic efficiency, sluggish ionic transport, and inferior temperature compatibility. In this work, the surface Al2 O3 coating layer is proposed as an artificial solid electrolyte interphase (SEI), which can serve as a physical barrier against the invasion of byproducts like HF(Hydrogen Fluoride) from the decomposition of electrolyte, and acts as a fast Li-ion transport pathway. Besides, the intrinsically high mechanical strength can effectively inhibit the volume expansion of the silicon particles, thus promoting the cyclability. The as-assembled battery cell with the Al2 O3 -coated Si-C anode exhibits a high initial Coulombic efficiency of 80% at RT and a capacity retention ratio up to ≈81.9% after 100 cycles, which is much higher than that of the pristine Si-C anode (≈74.8%). Besides, the expansion rate can also be decreased from 103% to 50%. Moreover, the Al2 O3 -coated Si-C anode also extends the working temperature from room temperature to 0 °C-60 °C. Overall, this work provides an efficient strategy for regulating the interface reactions of Si-based anode and pushes forward the practical applications at real conditions.

Nano Silicon Anode without Electrolyte Adding for Sulfide-Based All-Solid-State Lithium-Ion Batteries.

All-solid-state lithium-ion batteries (ASSLBs) employing silicon (Si) anode and sulfide electrolyte attract much attention, since they can achieve both high energy density and safety. For large-scale application, sheet-type Si anode matching sulfide based ASSLBs is preferred. Here, a LiAlO2 layer coated Si (Si@LiAlO2 ) is reported for sheet-type electrode. This electrode employs conventional slurry coating methods without adding any sulfide electrolyte. The effect of LiAlO2 coating on the electrochemical performance and morphology evolution of Si electrode is investigated. Since the high mechanical strength and ionic conductivity of LiAlO2 layer can sufficiently relieve the huge expansion of Si and promote the Li+ diffusion, the electrochemical performance is significantly enhanced. The Si@LiAlO2 electrodes deliver high coulombic efficiency exceeding 80% and hold considerable specific capacity of 1205 mAh g-1 (150 cycles, 0.33 C). The Si@LiAlO2 | LiNi0.83 Co0.11 Mn0.06 O2 full-cells exhibit a high reversible capacity of 147 mAh g-1 (0.28 mA cm-2 ) and a considerable capacity retention of 80.2% (62 cycles, 2.8 mA cm-2 ). This work demonstrates promising practicability and provides a new route for the scalable preparation of Si electrode sheets for ASSLBs with extended lifespan.

Is Soft Carbon a More Suitable Match for SiOx in Li-Ion Battery Anodes?

Silicon oxide (SiOx ), inheriting the high-capacity characteristic of silicon-based materials but possessing superior cycling stability, is a promising anode material for next-generation Li-ion batteries. SiOx is typically applied in combination with graphite (Gr), but the limited cycling durability of the SiOx /Gr composites curtails large-scale applications. In this work, this limited durability is demonstrated in part related to the presence of a bidirectional diffusion at the SiOx /Gr interface, which is driven by their intrinsic working potential differences and the concentration gradients. When Li on the Li-rich surface of SiOx is captured by Gr, the SiOx surface shrinks, hindering further lithiation. The use of soft carbon (SC) instead of Gr can prevent such instability is further demonstrated. The higher working potential of SC avoids bidirectional diffusion and surface compression thus allowing further lithiation. In this scenario, the evolution of the Li concentration gradient in SiOx conforms to its spontaneous lithiation process, benefiting the electrochemical performance. These results highlight the focus on the working potential of carbon as a strategy for rational optimization of SiOx /C composites toward improved battery performance.

The down-regulation of TAPP2 inhibits the migration of esophageal squamous cell carcinoma and predicts favorable outcome.

Tandem pH domain-containing proteins TAPP1 and TAPP2 are adaptor proteins that specifically bind to phosphatidylinositol-3,4-bisphosphate, or PI(3,4)P2, a product of phosphoinositide 3-kinases (PI3K). Although PI3K enzymes have multiple functions in cell biology, including cell migration, the functions of PI (3, 4) P2 and its binding proteins are not well understood. Previously studies found that TAPP2 is highly expressed in primary leukemic B cells that have strong migratory capacity. However, the function and underlying mechanisms of TAPP2 in ESCC remain largely unknown. In the present study, we investigated the level of TAPP2 in human esophageal squamous cell carcinoma (ESCC) tissues and in corresponding adjacent non-tumor tissues by immunohistochemistry (IHC) and western blot analyses. TAPP2 protein level was increased in ESCC tissues compared with corresponding adjacent non-tumor tissues. In vitro experiments showed that under-expression of TAPP2 reduced ESCC cell TE1 migration by wound-healing assays and transwell migration assays, and it was concurrent with the decreased expression of the phosphorylation of AKT. Taken together, these findings suggested that TAPP2 serves as oncogenic gene in ESCC and may serve as a new target for ESCC therapy.