The effect of TiO2 nanoparticles on bacterial growth: the effect of particle size and their structure - a systematic review.

One of the widely used microbiological methods to determine the toxicity of chemicals, catalysts, and other types of materials is the minimum inhibitory concentration (MIC) test. The present study aims to investigate the influence of composition of composite materials based on TiO2 and their particle size as well as bacterial type and shape based on the MIC values reported in the literature. The results show that among the 36 articles selected, most of the studies used Escherichia coli (E. coli) (26) and Staphylococcus aureus (S. aureus) (19) bacteria to determine MIC values. This study revealed that the MIC in values below 70 µg ml-1 for S. aureus was lower than that for E. coli bacteria (below 200 µg ml-1). Importantly, MIC value decreased from 60.6 to 7.66 µg ml-1 with decrease in the size of nanoparticles. It follows from the increased surface area for smaller-sized particles, thus increased interaction with bacteria during MIC test.

Utilization of the copper recovered from waste printed circuit boards as a metal precursor for the synthesis of TiO2/magnetic-MOF(Cu) nanocomposite: Application in photocatalytic degradation of pesticides in aquatic solutions.

In this study, a number of leaching solutions (H2SO4, CuSO4 and NaCl) and an electrochemical method were used together for the separation of Cu from waste printed circuit boards. Secondly, the magnetic-MOF(Cu) was synthesized using the Cu recovered from waste printed circuit boards. Thereafter, TiO2/mag-MOF(Cu) composite was prepared and its photocatalytic activity was assessed in the photo degradation of two prominent organophosphorus pesticides, namely malathion (MTN) and diazinon (DZN). The catalytic structure of the MOF-based composite was fully characterized by various analyses such as XRD, SEM, EDAX, FT-IR, VSM and UV-vis. The obtained analyses confirmed the successful synthesis of TiO2/mag-MOF(Cu) composite. The synthesized composite exhibited highly efficient in the degradation of both pollutants under the following conditions: pH 7, contaminant concentration 1 mg/L, the catalyst dosage of 0.4 g/L, visible light intensity 75 mW/cm2 and reaction time of 45 min. First order kinetic model was best suited with the experimental results (R2: 0.97-0.99 for different MTN and DZN concentrations). Trapping studies revealed that superoxide radicals (O2•-) played an important role during the degradation process. Furthermore, the catalyst demonstrated a superb recovery as well as high stability over five cyclic runs of reuse. In addition, the total organic carbon (TOC) analysis showed over 83% and 85% mineralization for MTN and DZN, respectively. The combined system of TiO2/mag-MOF(Cu)/Vis also exhibited a great level of efficiency and feasibility in the treatment of tap water and treated wastewater samples. It is concluded that TiO2/mag-MOF(Cu) could be used as an excellent catalyst for the photodegradation of MTN and DZN in aqueous solution.

Associations between long-term exposure to air pollution, diabetes, and hypertension in metropolitan Iran: an ecologic study.

Epidemiological studies on air pollution, diabetes, and hypertension conflict. This study examined air pollution, diabetes, and hypertension in adults in 11 metropolitan areas of Iran (2012-2016). Local environment departments and the Tehran Air Quality Control Company provided air quality data. The VIZIT website and Stepwise Approach to Chronic Disease Risk Factor Surveillance study delivered chronic disease data. Multiple logistic regression and generalized estimating equations evaluated air pollution-related diabetes and hypertension. In Isfahan, Ahvaz, and Tehran, PM2.5 was linked to diabetes. In all cities except Urmia, Yasuj, and Yazd, PM2.5 was statistically related to hypertension. O3 was connected to hypertension in Ahvaz, Tehran, and Shiraz, whereas NO2 was not. BMI and gender predict hypertension and diabetes. Diabetes, SBP, and total cholesterol were correlated. Iran's largest cities' poor air quality may promote diabetes and hypertension. PM2.5 impacts many cities' outcomes. Therefore, politicians and specialists have to control air pollution.

Extraction and determination of organic/inorganic pollutants in the ambient air of two cities located in metropolis of Tehran.

In the present study, PM2.5, volatile organic compounds (VOC), heavy metals, and polycyclic aromatic hydrocarbons (PAHs)-bonded PM2.5 as well as asbestos fibers were investigated in two cities in the east of Tehran, Iran. To this end, 72 samples were collected from six stations located in the cities of Varamin and Pakdasht from March 2018 to March 2019. The concentration of BTEX compounds, PAHs, and heavy metals were measured using gas chromatography-flame ionization detector (GC-FID), gas chromatography-mass spectrometry (GC-Mas), and inductively coupled plasma atomic emission spectroscopy (ICP-OES), respectively. In addition, phase contrast microscopy (PCM) method was used to identify the properties of asbestos fibers. The results obtained from the present showed that the mean concentrations of PM2.5, heavy metals, PAHs, BTEX, and asbestos fibers were 52.05 µg/m3, 319.08 ng/m3, 3.97 ng/m3, 40.58 µg/m3, and 2.84 f/L, respectively. In addition, the results obtained from PCA and heavy metals sources showed that transport fleets were the natural source of most of these pollutants. In case of PAH sources, transport and incineration of coal had the highest contribution in the emission. Furthermore, the risk assessment showed that most of the compounds have a higher risk value than the guideline value spatial distribution and also showed that stations close to airports, city terminals, and highways were more polluted than other parts of the city. Therefore, in order to have healthy air and with the least pollution, it seems necessary to formulate the necessary strategies in the cities of Varamin and Pakdasht.

Photocatalytic removal of bentazon by copper doped zinc oxide nanorods: Reaction pathways and toxicity studies.

In this study, bentazon herbicide was degraded photocatalytically by copper doped zinc oxide nanorods fabricated by using a facile co-precipitation method. The crystal structure, morphology, surface composition, functional groups on the surface and valence state of the nanorods were investigated by XRD, SEM-EDX, FTIR, and XPS material characterization techniques. Environmental parameters including solution pH, catalyst dose, bentazon concentration, purging gases, H2O2 content, organic compound type and reusability affecting the rate of photocatalytic degradation of bentazon were evaluated. Under the optimal conditions, [Bentazon]0 = 20 mg L-1, Cu-ZnO loading = 0.5 g L-1, H2O2 = 2 mM, pH = 7 and in the presence of oxygen gas, 100% of the herbicide was removed within 60 min. By raising bentazon concentration (10-50 mg L-1), kobs decreased to values between 0.14 and 0.006 min-1 and the calculated electrical energy per order (EEo) increased from 38.16 to 727.27 (kWh m-3), respectively. The degradation removal of the herbicide using the UV/Cu-ZnO method (98.28%) was higher than that of the UV/ZnO method (32.14%) process. Interestingly, the photocatalytic performances in the first and fifth reuse cycles during catalyst recyclability tests were found to be similar. Generally, the efficacy of the method in the decomposition of bentazon in drinking water (78.95%) and actual sewage (46.77%) declined because of the presence of other anions due to their role as a scavenger of photogenerated reactive species. Intermediate products in the photocatalytic degradation of bentazon identified by gas chromatography/mass spectrometry (GC/MS) analysis were 2-amino-N-isopropyl-benzamide, 2-amino-benzoic acid, N-isopropyl-2-nitro-benzamide, and acids such as pentenedioic acid, oxalic acid and propenoic acid. Furthermore, the main mechanism for the photocatalytic removal of bentazon was determined to be via attack by hydroxyl radicals (•OH). The results of toxicity in the photocatalytic removal of bentazon by D. magna showed LC50 and toxicity unit (TU) 48 h equal to 46.10 and 9.56 vol percent.

The association of hospital emergency admissions due to respiratory-cardiovascular diseases and acute myocardial infarction with air pollution in Tehran during 2005-2014.

Background: Air pollution is one of the main reasons for disease and emergency hospitalizations. Therefore, air pollution control and hospital preparedness are of paramount importance. This study was conducted to determine the association of air pollutant levels with the rate of hospital emergency admissions due to respiratory and cardiovascular diseases and acute myocardial infarction in Tehran during the last decade. Methods: This was a cross sectional study. At first, information on hourly concentration of air pollutants was gathered from Tehran Environmental Protection Agency and Air Quality Control Company. Raw data and meteorological parameters were used in Excel format to prepare an input file. The number of emergency hospital admissions due to pollutant exposure was assessed using the AirQ2.2.3 model. Results: Results of this study revealed that there were 54 352 cases of emergency hospitalizations due to respiratory diseases in a relative risk of 1.0048 [1.0008-1.0112] and 20 990 cases of emergency hospitalizations due to cardiovascular diseases in a relative risk of 1.009[1.006-1.013] during 2005-2014. In addition, 3478 patients were admitted to the emergency department because of acute myocardial infarction with RR of 1.0026 [1.0026-1.0101]. Conclusion: This study demonstrated that a high percentage of hospital emergency admissions was because of respiratory and cardiovascular diseases. Moreover, it was found that acute myocardial infarction could be due to the high level of air pollution and could increase admissions to the emergency department. Therefore, appropriate measures are needed to reduce air pollution and increase hospital preparedness.

Enhancement of photocatalytic activity of Cu-doped ZnO nanorods for the degradation of an insecticide: Kinetics and reaction pathways.

The photocatalytic degradation of organophosphorus pesticide such as diazinon was investigated by Cu-doped ZnO nanorods. Cu-doped ZnO nanorods were synthesized via a facile co-precipitation method. The catalyst was characterized by XRD, FESEM, EDX, VSM, XPS, and pHzpc techniques. The effects of some operational parameters such as solution pH, Cu-doped ZnO nanorods dosage, initial diazinon concentration, oxygen and nitrogen gases, H2O2 concentration, and type of organic compounds on the degradation efficiency were discussed through the photocatalytic experiments using the Cu-doped ZnO nanorods. Neutral pH was selected as an optimal pH condition due to a photo-corrosion of ZnO in acidic and basic conditions. As the Cu-doped ZnO nanorods dosage increased up to 0.2 g/L, degradation efficiency of diazinon was continuously enhanced. Pseudo-first-order rate constant (kobs) was decreased from 0.051 to 0.0052 min-1 and electrical energy per order (EEo) was increased from 94.12 to 923.08 (kWh/m3) by increasing diazinon concentration from 10 to 50 mg/L, respectively. The efficiency of the UV/Cu-doped ZnO for diazinon removal was approximately 96.97%, which was more effective than the UV/ZnO process (58.52%). Photocatalytic activity was maintained even after five successive cycles.

Contaminants of emerging concern: a review of new approach in AOP technologies.

The presence of contaminants of emerging concern (CECs) such as pharmaceuticals and personal care products (PPCPs), endocrine-disrupting compounds (EDCs), flame retardants (FRs), pesticides, and artificial sweeteners (ASWs) in the aquatic environments remains a major challenge to the environment and human health. In this review, the classification and occurrence of emerging contaminants in aquatic environments were discussed in detail. It is well documented that CECs are susceptible to poor removal during the conventional wastewater treatment plants, which introduce them back to the environment ranging from nanogram per liter (e.g., carbamazepine) up to milligram per liter (e.g., acesulfame) concentration level. Meanwhile, a deep insight into the application of advanced oxidation processes (AOPs) on mitigation of the CECs from aquatic environment was presented. In this regard, the utilization of various treatment technologies based on AOPs including ozonation, Fenton processes, sonochemical, and TiO2 heterogeneous photocatalysis was reviewed. Additionally, some innovations (e.g., visible light heterogeneous photocatalysis, electro-Fenton) concerning the AOPs and the combined utilization of AOPs (e.g., sono-Fenton) were documented.

Magnetic Fe3O4@C nanoparticles as adsorbents for removal of amoxicillin from aqueous solution.

In the present study, powder activated carbon (PAC) combined with Fe(3)O(4) magnetite nanoparticles (MNPs) were used for the preparation of magnetic composites (MNPs-PAC), which was used as an adsorbent for amoxicillin (AMX) removal. The properties of magnetic activated carbon were characterized by scanning electron microscopy, transmission electron microscopy, X-ray diffraction, Brunaeur, Emmett and Teller and vibrating sample magnetometer. The operational factors affecting adsorption such as pH, contact time, adsorbent dosage, initial AMX concentration and temperature were studied in detail. The high surface area and saturation magnetization for the synthesized adsorbent were found to be 671.2 m(2)/g and 6.94 emu/g, respectively. The equilibrium time of the adsorption process was 90 min. Studies of adsorption equilibrium and kinetic models revealed that the adsorption of AMX onto MNPs-PAC followed Freundlich and Langmuir isotherms and pseudo-second-order kinetic models. The calculated values of the thermodynamic parameters, such as ΔG°, ΔH° and ΔS° demonstrated that the AMX adsorption was endothermic and spontaneous in nature. It could be concluded that MNPs-PAC have a great potential for antibiotic removal from aquatic media.

Evaluating the mortality and health rate caused by the PM2.5 pollutant in the air of several important Iranian cities and evaluating the effect of variables with a linear time series model.

All over the world, the level of special air pollutants that have the potential to cause diseases is increasing. Although the relationship between exposure to air pollutants and mortality has been proven, the health risk assessment and prediction of these pollutants have a therapeutic role in protecting public health, and need more research. The purpose of this research is to evaluate the ill-health caused by PM2.5 pollution using AirQ + software and to evaluate the different effects on PM2.5 with time series linear modeling by R software version 4.1.3 in the cities of Arak, Esfahan, Ahvaz, Tabriz, Shiraz, Karaj and Mashhad during 2019-2020. The pollutant hours, meteorology, population and mortality information were calculated by the Environmental Protection Organization, Meteorological Organization, Statistics Organization and Statistics and Information Technology Center of the Ministry of Health, Treatment and Medical Education for 24 h of PM2.5 pollution with Excel software. In addition, having 24 h of PM2.5 pollutants and meteorology is used to the effect of variables on PM2.5 concentration. The results showed that the highest and lowest number of deaths due to natural deaths, ischemic heart disease (IHD), lung cancer (LC), chronic obstructive pulmonary disease (COPD), acute lower respiratory infection (ALRI) and stroke in The effect of disease with PM2.5 pollutant in Ahvaz and Arak cities was 7.39-12.32%, 14.6-17.29%, 16.48-8.39%, 10.43-18.91%, 12.21-22.79% and 14.6-18.54 % respectively. Another result of this research was the high mortality of the disease compared to the mortality of the nose. The analysis of the results showed that by reducing the pollutants in the cities of Karaj and Shiraz, there is a significant reduction in mortality and linear modeling provides a suitable method for air management planning.

A comprehensive study on the spatial and temporal variation of BTEX and asbestos in the northwest of Iran: Human risk assessment.

Substances like asbestos and other air pollutants, such as BTEX (benzene, toluene, ethylbenzene, and xylene), are hazardous compounds due to their adverse effects on human health. This study aims to investigate the levels, seasonal variations, spatial distribution, potential sources, and associated health risks associated with BTEX compounds and asbestos fibers in the ambient air of Tabriz. Air samples were taken at 16 different locations during the 2020-2021 period. Glass containers with charcoal were used for sample collection, and the BTEX content was determined using the GC-FID method. Phase-contrast microscopy (PCM) analysis was conducted with a low-volume peripheral pump for asbestos fiber sampling. The results showed that the average concentration of ∑BTEX was 37.94 and 27.98 µg/m3 in autumn and spring, respectively. The same parameter was 2.26 and 1.68 f/L for asbestos in the autumn and winter, respectively. The contribution of BTEX to ozone formation potential (OFP) in the research area showed that xylene and toluene were the major contributors to ozone production in different seasons. The risk of exposure to benzene compounds was 24 × 10-4 in children and 55.9 × 10-4 in adults, while the risk of exposure to ethylbenzene was 3.78 × 10-4 in children and 3.25 × 10-4 in adults. The estimated lifetime cancer risk was found to be the highest for benzene, followed by ethylbenzene. The estimated cancer risk for benzene and ethylbenzene exceeded the threshold values set by EPA, which signals a significant carcinogenic risk due to exposure to these substances in the ambient air of Tabriz. According to the EPA guidelines, the low carcinogenicity risk levels are between 10-4 and 10-6. According to the findings for the exposure to asbestos fibers, the maximum values of excess cancer risk (ECR) and estimated lifetime cancer risk (ELCR) were observed in the 16-30 age range across all locations, suggesting increased exposure to asbestos fibers compared to other age groups.

Investigation of photocatalytic-proxone process performance in the degradation of toluene and ethyl benzene from polluted air.

In this study, toluene and ethylbenzene were degraded in the photocatalytic-proxone process using BiOI@NH2-MIL125(Ti)/Zeolite nanocomposite. The simultaneous presence of ozone and hydrogen peroxide is known as the proxone process. Nanocomposite Synthesis was carried out using the solvothermal method. Inlet airflow, ozone concentrations, H2O2 concentrations, relative humidity, and initial pollutants concentrations were studied. The nanocomposite was successfully synthesized based on FT-IR, BET, XRD, FESEM, EDS element mapping, UV-Vis spectra and TEM analysis. A flow rate of 0.1 L min-1, 0.3 mg min-1 of ozone, 150 ppm of hydrogen peroxide, 45% relative humidity, and 50 ppmv of pollutants were found to be optimal operating conditions. Both pollutants were degraded in excess of 95% under these conditions. For toluene and ethylbenzene, the synergistic of mechanisms effect coefficients were 1.56 and 1.76, respectively. It remained above 95% efficiency 7 times in the hybrid process and had good stability. Photocatalytic-proxone processes were evaluated for stability over 180 min. The remaining ozone levels in the process was insignificant (0.01 mg min-1). The CO2 and CO production in the photocatalytic-proxone process were 58.4, 5.7 ppm for toluene and 53.7, and 5.5 ppm for ethylbenzene respectively. Oxygen gas promoted and nitrogen gas had an inhibitory effect on the effective removal of pollutants. During the pollutants oxidation, various organic intermediates were identified.

PAHs pollution in the outdoor air of areas with various land uses in the industrial city of Iran: distribution, source apportionment, and risk assessment.

Shahryar city regions with various land uses had their outdoor air concentrations of PM2.5-bound PAHs determined. Totally, 32 samples were taken - eight samples from the industrial region air (IS), eight samples from the high-traffic urban regions air (HTS), eight samples from the air of commercial regions (CS), and eight samples from residential areas (RS), which were analyzed by GC-MS. According to the study's findings, in the outdoor air of IS, HTS, CS, and RS, there were mean Æ©PAHs concentrations of 23.25 ± 20.22, 38.88 ± 26.53, 6.97 ± 4.26, and 4.48 ± 3.13 ng/m3, respectively. As comparison to CS and RS, mean concentration of Æ©PAHs in samples from HTS and IS was substantially greater (p < 0.05). Using the Unmix.6 receptor model, sources of PAHs in the air of Shahryar were allocated. The model's results show that 42% of PAHs come from diesel vehicles and industrial activities, 36% from traffic and other transportation sources, and 22% from heating sources and coal burning. The carcinogenicity suffering resulting from exposure to PAHs was as follows: This value for children of the ingestion, inhalation pathways and dermal contact is (1.90 × 10-6-1.38 × 10-4), (5.5 × 10-11-2.67 × 10-9) and (2.36 × 10-6-1.72 × 10-4), respectively. Also, for adults were (1.47 × 10-6 - 1.07 × 10-4), (1.14 × 10-10 - 5.27 × 10-9) and (3.68 × 10-6- 2.87 × 10-4), respectively. In general, the analyzed region's carcinogenicity risk estimates fell within the range of acceptable limit.

Characterization of ionic composition of TSP and PM10 during the Middle Eastern Dust (MED) storms in Ahvaz, Iran.

Because of the recent frequent observations of major dust storms in southwestern cities in Iran such as Ahvaz, and the importance of the ionic composition of particulate matters regarding their health effects, source apportionment, etc., the present work was conducted aiming at characterizing the ionic composition of total suspended particles (TSP) and particles on the order of ∼10 µm or less (PM(10)) during dust storms in Ahvaz in April-September 2010. TSP and PM(10) samples were collected and their ionic compositions were determined using an ion chromatography. Mean concentrations of TSP and PM(10) were 1,481.5 and 1,072.9 µg/m(3), respectively. Particle concentrations during the Middle Eastern Dust (MED) days were up to four times higher than those in normal days. Ionic components contributed to only 9.5% and 11.3% of the total mass of TSP and PM(10), respectively. Crustal ions were most abundant during dust days, while secondary ions were dominant during non-dust days. Ca(2+)/Na(+) and Cl(-)/Na(+) ratios can be considered as the indicators for identification of the MED occurrence. It was found that possible chemical forms of NaCl, (NH(4))(2)SO(4), KCl, K(2)SO(4), CaCl(2), Ca(NO(3))(2), and CaSO(4) may exist in TSP. Correlation between the anionic and cationic components suggests slight anion and cation deficiencies in TSP and PM(10) samples, though the deficiencies were negligible.

Enhanced photocatalytic activity of Fe2O3@ZnO decorated CQD for inactivation of Escherichia coli under visible light irradiation.

The present study, magnetically separable Fe2O3@ZnO/CQD nanocomposite was successfully prepared via hydrothermal process and characterized with SEM-EDX, XRD, FTIR, VSM and DRS analysis. The effect of operational parameters includes photocatalyst dosage, photocatalyst type, CQD content and Escherichia coli (E. coli) concentration were evaluated on the E. coli inactivation. The disinfecting ability of nanocomposite components was obtained as Fe2O3@ZnO/CQD> Fe2O3@ZnO> ZnO> Fe2O3> CQD which shows a synergetic effect among different components. The highest E. coli inactivation rate (Kmax=0.7606 min-1) was obtained at photocatalyst dosage of 0.2 g/L and 15% CQD content. The MIC and MBC values value for E. coli were determined 0.1172 mg/mL and 0.4948 respectively that the results tests proved the antibacterial functions of the Fe2O3@ZnO/CQD. Nanocomposite showed the high reusability after 4 consecutive cycles, Kmax decreased from 0.7606 min-1 to 0.6181 min-1. Quenching experiments showed •OH and h+ are the main reactive oxygen species involved in the E. coli inactivation.

Exploring the visible light-assisted conversion of CO2 into methane and methanol, using direct Z-scheme TiO2@g-C3N4 nanosheets: synthesis and photocatalytic performance.

The rapid growth of carbon dioxide (CO2) emissions raises concern about the possible consequences of atmospheric CO2 increase, such as global warming and greenhouse effect. Photocatalytic CO2 conversion has attracted researchers' interests to find a sustainable route for its elimination. In the present study, a direct Z-scheme TiO2/g-C3N4 composite (T-GCN) was fabricated via a facile hydrothermal route for the photocatalytic reduction of CO2 into methane (CH4) and methanol (CH3OH), under visible light irradiation without an electron mediator. The microstructure of the as-obtained TiO2/g-C3N4 nanocomposites was fully characterized for its physicochemical, structural, charge separation, electronic, and photo-excited carrier separation properties. The effect of CO2 and H2O partial pressure was studied to find the best operational conditions for obtaining maximum photocatalytic efficiency; the PCO2 and PH2O were 75.8 and 15.5 kPa, respectively, whereas, by increasing the light intensity from 20 to 80 mW/cm2, a remarkable improvement in the reduction rate takes place (from 11.04 to 32.49 µmol.gcat-1.h-1 methane production, respectively). Finally, under the most favorable light, PCO2 and PH2O conditions, high methanol and methane rates were obtained from the CO2 photocatalytic reduction through T-GCN (1.44 µmol.gcat.-1.h-1 and 32.49 µmol.gcat.-1.h-1, respectively) and an integrated proposition for the Z-scheme mechanism of photocatalytic reduction was proposed. This study offers a promising strategy to synthesize a Z-scheme T-GCN heterojunction with high photocatalytic performance for effective CO2 conversion.

The potential osteoporosis due to exposure to particulate matter in ambient air: Mechanisms and preventive methods.

Air pollution and health consequences associated with exposure to air pollutants, such as particulate matter, are of serious concerns in societies. Over the recent years, numerous studies have investigated the relation of many diseases with air pollutants. This review used a search strategy to provide the comprehensive information on the relationship between particle matters and osteoporosis. To this end, three search databases were used to find the articles focused on particle matters and osteoporosis. After the screening process, 13 articles related to the purpose of the study were selected and the relevant data were extracted. The results indicated that osteoporosis is significantly associated with PM10. However, this association with PM2.5 remains unclear. In addition, particle materials indirectly lead to the osteoporosis and bone fractures as a consequence of reduced UV-B, reduced adsorption of vitamin D. Furthermore, they can lead to other diseases by use of drugs with adverse effects on bone health, and creating conditions that may increase the risk of falling in the elderly. This review shows that although more accurate research is needed to determine the mechanism and risk of exposure to particulate matter in the air on bone health, the negative effects of this pollutant on bone mineral density (BMD) are evident.Implications: PM is usually classified by its size or aerodynamic diameter; PM10 denotes particles < 10 µm in diameter; PM2.5 particles are <2.5 µm in diameter. Many epidemiological studies have shown that short-term exposure to PM might reduce lung function. However, short-term effects might be reversible, and the main concern is attributed to long-term exposure. A major public health concern that may be affected by numerous metabolic and even environmental risk factors is osteoporosis. The purpose of this systematic review was to investigate the role of PM in the occurrence or exacerbation of osteoporosis in citizens.

The effect of PM2.5-related hazards on biomarkers of bronchial epithelial cells (A549) inflammation in Karaj and Fardis cities.

Fine particles (especially PM2.5 particles) in ambient air can cause irreversible effects on human health. In the present study, seasonal variations in toxicity PM2.5 (cell viability and release of pro-inflammatory cytokines) were exposed human lung cells (A549) to concentrations of PM2.5 samples in summer (sPM2.5) and winter (wPM2.5) seasons. Cells were separately exposed to three concentrations of PM2.5 (25, 50, and 100 µg/mL) and three times (12 h, 1 and 2 days). We evaluated cell viability by MTT assay [3- (4, 5-dimethylthiazol-2-yl) -2, 5-diphenyltetrazolium bromide] and liberation of pro-inflammatory cytokines (interleukin-6 and interleukin-8) by the ELISA method. The toxicological results of this study showed that increasing the concentration of PM2.5 particulates and contact time with it reduces cell viability and increases inflammatory responses. Seasonal cytotoxicity of PM2.5 particles in high-traffic areas at summer season compared to winter season was lower. The lowest percent of viability at 2 days of exposure and 100 µg/mL exposure in the winter sample was observed. Also, PM2.5 particles were influential in the amount of interleukins 8 and 6. The average release level of IL-6 and IL-8 in the cold season (winter) and the enormous exposure time and concentrations (2 days-100 µg/mL) was much higher than in the hot season (summer). These values were twice as high for winter PM2.5 samples as for summer samples. The compounds in PM2.5 at different seasons can cause some biological effects. The samples' chemical characteristics in two seasons displayed that the PMs were diverse in chemical properties. In general, heavy metals and polycyclic aromatic hydrocarbons were more in the winter samples. However, the samples of wPM2.5 had a lower mass quota of metals such as aluminum, iron, copper, zinc, and magnesium. Concentrations of chromium, cadmium, arsenic, mercury, nickel, and lead were more significant in the sample of wPM2.5.

Urban air pollution control policies and strategies: a systematic review.

A wide range of policies, strategies, and interventions have been implemented to improve air quality all over the world. This systematic review comprehensively appraises the policies and strategies on air pollutants controls enacted in different countries, worldwide. Three databases, Web of Science, PubMed and Scopus, were used for the search. After screening, a total of 114 eligible manuscripts were selected from 2219 documents for further analysis. Selected articles were divided into two categories: (1) articles focusing on introducing the policies and strategies enacted for controlling air pollution in different countries, and (2) articles which focused on different policies and strategies to control one or more specific pollutants. In the former one, urban air pollution control strategies and policies were divided into four categories, namely, general strategies and policies, transportation, energy, and industry. In case of latter category, policies and strategies focused on controlling six pollutants (PM, SO2, NO2, VOCS, O3 and photochemical smog). The results indicated that, the most common policies and strategies enacted in most countries are pertinent to the transportation sector. Changing energy sources, in particular elimination or limited use of solid fuels, was reported as an effective action by governments to reduce air pollution. Overall, most policies enacted by governments can be divided into three general categories: (a) incentive policies such as implementing a free public transportation program to use fewer private cars, (b) supportive policies such as paying subsidies to change household fuels, and (c) punitive policies such as collecting tolls for cars to enter the congestion charging areas. Depending on the circumstances, these policies are implemented alone or jointly. In addition to the acceptance of international agreements to reduce air pollution by governments, greater use of renewable energy, clean fuels, and low-pollution or no-pollution vehicles such as electric vehicles play an important role in reducing air pollution.

Preparation of a thin-film nanocomposite forward osmosis membrane for the removal of organic micro-pollutants from aqueous solutions.

In this study, a thin-film nanocomposite forward osmosis (TFN FO) membrane was synthesized. The properties and structures of membranes were evaluated for the removal of three organic micro-pollutants from synthetic and real industrial wastewater samples. Laboratory scale fabrication thin-film nanocomposite forward osmosis (FO) membranes composed of a support layer and an active layer. The former was constructed by adding different weight ratios of polyethylene glycol 400 (PEG-400) (0-8 wt.%), polysulfone (PSf), and 1-methyl, 2-pyrrolidone via the phase inversion process, while the latter was synthesized by the incorporation of different weight ratios of graphene oxide (GO) (0-0.012 wt.%), M-phenylenediamine, and 1, 3, 5-benzene trichloride into polyamide layer through the interfacial polymerization reaction. In comparison with thin-film composite (TFC) membranes, the TFN membranes revealed higher hydrophilicity, porosity, water permeability, water flux and salt rejection and lower internal concentration polarization (ICP), reverse salt flux and specific reverse salt flux. The TFN membrane containing 0.008% GO in the active layer and 4% PEG 400 in the support layer exhibited maximum water flux (34.3 LMH) and rejection rate of benzene, phenol and toluene (97%, 84%, and 91%, respectively). The results revealed that the TFN-FO membranes possess a promising potential to improve the water flux and wastewater treatment.