Using mobile eye tracking to measure cognitive load through gaze behavior during walking in lower limb prosthesis users: A preliminary assessment.

BACKGROUND: Lower limb amputation does not affect only physical and psychological functioning but the use of a prosthetic device can also lead to increased cognitive demands. Measuring cognitive load objectively is challenging, and therefore, most studies use questionnaires that are easy to apply but can suffer from subjective bias. Motivated by this, the present study investigated whether a mobile eye tracker can be used to objectively measure cognitive load by monitoring gaze behavior during a set of motor tasks. METHODS: Five prosthetic users and eight able-bodied controls participated in this study. Eye tracking data and kinematics were recorded during a set of motor tasks (level ground walking, walking on uneven terrain, obstacle avoidance, stairs up and ramp down, as well as ramp up and stairs down) while the participants were asked to focus their gaze on a visual target for as long as possible. Target fixation times and increase in pupil diameters were determined and correlated to subjective ratings of cognitive load. FINDINGS: Overall, target fixation time and pupil diameter showed strong negative and positive correlations, respectively, to the subjective rating of cognitive load in the able-bodied controls (-0.75 and 0.80, respectively). However, the individual correlation strength, and in some cases, even the sign, was different across participants. A similar trend could be observed in prosthetic users. INTERPRETATION: The results of this study showed that a mobile eye tracker may be used to estimate cognitive load in prosthesis users during locomotor tasks. This paves the way to establish a new approach to assessing cognitive load, which is objective and yet practical and simple to administer. Nevertheless, future studies should corroborate these results by comparing them to other objective measures as well as focus on translating the proposed approach outside of a laboratory.

The impact of transfemoral socket adduction on pelvic and trunk stabilization during level walking - A biomechanical study.

BACKGROUND: It is common practice to align transfemoral prosthetic sockets in adduction, due to the physiologic, adducted femoral alignment in unimpaired legs. An adducted femoral and socket alignment helps tightening hip abductors to stabilize the pelvis and reduce pelvic and trunk related compensatory movements. RESEARCH QUESTION: How do different socket adduction conditions (SAC) of transfemoral sockets affect pelvic and trunk stabilization during level ground walking in the frontal plane? METHODS: Seven persons with transfemoral amputation with medium residual limb length participated in this study. The prosthetic alignment in the sagittal plane was performed according to established recommendations. SAC varied (0°, 3°, 6°, 9°). Kinematic and kinetic parameters were recorded in a gait laboratory with a 12-camera optoelectronic system and two piezoelectric force plates embedded in a 12-m walkway. The measurements were performed during level ground walking with self-selected comfortable gait speed. RESULTS: In the frontal plane, nearly all investigated kinematic and kinetic parameters showed a strong correlation with the SAC. The pelvis was raised on the contralateral side throughout the gait cycle with increasing SAC. During the prosthetic side stance phase, the mean shoulder obliquity and mean lateral trunk lean to the prosthetic side tended to be reduced with increased SAC. Prosthetic side hip abduction moment decreased with increasing SAC. SIGNIFICANCE: The results confirm that transfemoral SAC contributes to pelvic stabilization and reduced compensatory movements of the pelvis and trunk. Transfemoral SAC of 6 ± 1° for bench alignment seems adequate for amputees with medium residual limb length. However, the optimum value for the individual patient may differ slightly.

Comparative biomechanical evaluation of two technologically different microprocessor-controlled prosthetic knee joints in safety-relevant daily-life situations.

Safety-relevant gait situations (walking on stairs and slopes, walking backwards, walking with small steps, simulated perturbations of swing phase extension) were investigated in a motion analysis laboratory with six unilateral transfemoral amputees using two different microprocessor-controlled prosthetic knee joints (Rheo Knee XC, C-Leg). A randomized crossover design was chosen. The study results imply that the performance and safety potential of a microprocessor-controlled knee joint can be associated with the individual control algorithms and the technological concepts that are implemented to generate motion resistances for controlling flexion and extension movements. When walking with small steps, advantages of the "default swing" concept used in the Rheo Knee XC were identified due to a highly reproducible swing phase release. However, when walking backwards, this concept may lead to an uncontrolled knee flexion which partly resulted in falls. When walking down stairs, walking on slopes or while recovering from a stumble after perturbations of the swing phase extension, the C-Leg demonstrated a reliable prosthetic side load-bearing capacity resulting in reduced loading on the residual body. In contrast, the Rheo Knee XC required increased compensatory movements of the remaining locomotor system in order to compensate for reduced load-bearing and safety reserves.