Dopant-additive synergism enhances perovskite solar modules.

Perovskite solar cells (PSCs) are among the most promising photovoltaic technologies owing to their exceptional optoelectronic properties1,2. However, the lower efficiency, poor stability and reproducibility issues of large-area PSCs compared with laboratory-scale PSCs are notable drawbacks that hinder their commercialization3. Here we report a synergistic dopant-additive combination strategy using methylammonium chloride (MACl) as the dopant and a Lewis-basic ionic-liquid additive, 1,3-bis(cyanomethyl)imidazolium chloride ([Bcmim]Cl). This strategy effectively inhibits the degradation of the perovskite precursor solution (PPS), suppresses the aggregation of MACl and results in phase-homogeneous and stable perovskite films with high crystallinity and fewer defects. This approach enabled the fabrication of perovskite solar modules (PSMs) that achieved a certified efficiency of 23.30% and ultimately stabilized at 22.97% over a 27.22-cm2 aperture area, marking the highest certified PSM performance. Furthermore, the PSMs showed long-term operational stability, maintaining 94.66% of the initial efficiency after 1,000 h under continuous one-sun illumination at room temperature. The interaction between [Bcmim]Cl and MACl was extensively studied to unravel the mechanism leading to an enhancement of device properties. Our approach holds substantial promise for bridging the benchtop-to-rooftop gap and advancing the production and commercialization of large-area perovskite photovoltaics.

Green-Chemistry-Inspired Synthesis of Cyclobutane-Based Hole-Selective Materials for Highly Efficient Perovskite Solar Cells and Modules.

Hybrid lead halide perovskite solar cells (PSCs) have emerged as potential competitors to silicon-based solar cells with an unprecedented increase in power conversion efficiency (PCE), nearing the breakthrough point toward commercialization. However, for hole-transporting materials, it is generally acknowledged that complex structures often create issues such as increased costs and hazardous substances in the synthetic schemes, when translated from the laboratory to manufacture on a large scale. Here, we present cyclobutane-based hole-selective materials synthesized using simple and green-chemistry inspired protocols in order to reduce costs and adverse environmental impact. A series of novel semiconductors with molecularly engineered side arms were successfully applied in perovskite solar cells. V1366-based PSCs feature impressive efficiency of 21 %, along with long-term operational stability under atmospheric environment. Most importantly, we also fabricated perovskite solar modules exhibiting a record efficiency over 19 % with an active area of 30.24 cm2 .

Asymmetrically Substituted 10H,10'H-9,9'-Spirobi[acridine] Derivatives as Hole-Transporting Materials for Perovskite Solar Cells.

Hole-transporting materials (HTMs) based on the 10H, 10'H-9,9'-spirobi [acridine] core (BSA50 and BSA51) were synthesized, and their electronic properties were explored. Experimental and theoretical studies show that the presence of rigid 3,6-dimethoxy-9H-carbazole moieties in BSA 50 brings about improved hole mobility and higher work function compared to bis(4-methoxyphenyl)amine units in BSA51, which increase interfacial hole transportation from perovskite to HTM. As a result, perovskite solar cells (PSCs) based on BSA50 boost power conversion efficiency (PCE) to 22.65 %, and a PSC module using BSA50 HTM exhibits a PCE of 21.35 % (6.5×7 cm) with a Voc of 8.761 V and FF of 79.1 %. The unencapsulated PSCs exhibit superior stability to devices employing spiro-OMeTAD, retaining nearly 90 % of their initial efficiency after 1000 h operation output. This work demonstrates the high potential of molecularly engineered spirobi[acridine] derivatives as HTMs as replacements for spiro-OMeTAD.

Stable Perovskite Solar Cells Using Molecularly Engineered Functionalized Oligothiophenes as Low-Cost Hole-Transporting Materials.

Triarylamine-substituted bithiophene (BT-4D), terthiophene (TT-4D), and quarterthiophene (QT-4D) small molecules are synthesized and used as low-cost hole-transporting materials (HTMs) for perovskite solar cells (PSCs). The optoelectronic, electrochemical, and thermal properties of the compounds are investigated systematically. The BT-4D, TT-4D, and QT-4D compounds exhibit thermal decomposition temperature over 400 °C. The n-i-p configured perovskite solar cells (PSCs) fabricated with BT-4D as HTM show the maximum power conversion efficiency (PCE) of 19.34% owing to its better hole-extracting properties and film formation compared to TT-4D and QT-4D, which exhibit PCE of 17% and 16%, respectively. Importantly, PSCs using BT-4D demonstrate exceptional stability by retaining 98% of its initial PCE after 1186 h of continuous 1 sun illumination. The remarkable long-term stability and facile synthetic procedure of BT-4D show a great promise for efficient, stable, and low-cost HTMs for PSCs for commercial applications.

Dopant-Free Hole Transport Materials Afford Efficient and Stable Inorganic Perovskite Solar Cells and Modules.

The emerging CsPbI3 perovskites are highly efficient and thermally stable materials for wide-band gap perovskite solar cells (PSCs), but the doped hole transport materials (HTMs) accelerate the undesirable phase transition of CsPbI3 in ambient. Herein, a dopant-free D-π-A type HTM named CI-TTIN-2F has been developed which overcomes this problem. The suitable optoelectronic properties and energy-level alignment endow CI-TTIN-2F with excellent charge collection properties. Moreover, CI-TTIN-2F provides multisite defect-healing effects on the defective sites of CsPbI3 surface. Inorganic CsPbI3 PSCs with CI-TTIN-2F HTM feature high efficiencies up to 15.9 %, along with 86 % efficiency retention after 1000 h under ambient conditions. Inorganic perovskite solar modules were also fabricated that exhibiting an efficiency of 11.0 % with a record area of 27 cm2 . This work confirms that using efficient dopant-free HTMs is an attractive strategy to stabilize inorganic PSCs for their future scale-up.

Using redox-sensitive mitochondrial cytochrome Raman bands for label-free detection of mitochondrial dysfunction.

Mitochondrial activity is a widely used criterion to judge the metabolic condition of a living specimen. Numerous methods have been developed for related analyses, including the detection of O2 consumption, trans-membrane potential, and ATP production. In this study, we demonstrate that the redox state of cytochromes can serve as a sensitive mitochondrial activity indicator in glutamate-stressed neuronal cells. Mitochondrial dysfunction was detected by Raman imaging as early as 30 min after glutamate-stress induction. By comparing this result with other commonly used mitochondrial function assays, we found Raman imaging has a similar sensitivity to ATP production and trans-membrane potential assays. Other viability tests, such as MTT assay and ROS production tests, showed a slower response than our method. A thorough understanding of cytochrome dynamics with our new method will help establish Raman spectroscopy as a competitive clinical diagnosis tool for neurodegenerative diseases involving mitochondrial dysfunction.

The influence of visual field position induced by a retinal prosthesis simulator on mobility.

PURPOSE: Our aim is to develop a new generation of suprachoroidal-transretinal stimulation (STS) retinal prosthesis using a dual-stimulating electrode array to enlarge the visual field. In the present study, we aimed to examine how position and size of the visual field-created by a retinal prosthesis simulator-influenced mobility. METHODS: Twelve healthy subjects wore retinal prosthesis simulators. Images captured by a web camera attached to a head-mounted display (HMD) were processed by a computer and displayed on the HMD. Three types of artificial visual fields-designed to imitate phosphenes-obtained by a single (5 × 5 electrodes; visual angle, 15°) or dual (5 × 5 electrodes ×2; visual angle, 30°) electrode array were created. Visual field (VF)1 is an inferior visual field, which corresponds to a dual-electrode array implanted in the superior hemisphere. VF2 is a superior visual field, which corresponds to a single-electrode array implanted in the inferior hemisphere. VF3 is a superior visual field, which corresponds to a dual-electrode array implanted in the inferior hemisphere. In each type of artificial visual field, a natural circular visual field (visual angle, 5°) which imitated the vision of patients with advanced retinitis pigmentosa existed at the center. Subjects were instructed to walk along a black carpet (6 m long × 2.2 m wide) without stepping on attached white circular obstacles. Each obstacle was 20 cm in diameter, and obstacles were installed at 40-cm intervals. We measured the number of footsteps on the obstacles, the time taken to complete the obstacle course, and the extent of head movement to scan the area (head-scanning). We then compared the results recorded from these 3 types of artificial visual field. RESULTS: The number of footsteps on obstacles was lowest in VF3 (One-way ANOVA; P = 0.028, Fisher's LSD; VF 1 versus 3 P = 0.039, 2 versus 3 P = 0.012). No significant difference was observed for the time to complete the obstacle course or the extent of head movement between the 3 visual fields. CONCLUSION: The superior and wide visual field (VF3) obtained by the retinal prosthesis simulator resulted in better mobility performance than the other visual fields.

Comparison of visual fatigue caused by head-mounted display for virtual reality and two-dimensional display using objective and subjective evaluation.

This study aimed to evaluate objective and subjective visual fatigue experienced before and after performing a visual task while using a head-mounted display for virtual reality (VR-HMD) and two-dimensional (2D) display. Binocular fusion maintenance (BFM) was measured using a binocular open-view Shack-Hartmann wavefront aberrometer equipped with liquid crystal shutters. Twelve healthy subjects performed the BFM test and completed a questionnaire regarding subjective symptoms before and after performing a visual task that induces low visually induced motion sickness (VIMS). BFM (p = .87) and total subjective eye symptom scores (p = .38) were not significantly different between both groups, although these values were significantly lower after the visual task than before the task within both groups (p < .05). These findings suggest that visual fatigue after using a VR-HMD is not significantly different from that after using a 2D display in the presence of low-VIMS VR content. Practitioner summary: Objective and subjective evaluation of visual fatigue were not significantly different with the use of a head-mounted display for virtual reality (VR-HMD) and two-dimensional display. These results should be valuable not only to engineers developing VR content but also to researchers involved in the evaluation of visual fatigue using VR-HMD. Abbreviations: VR: virtual reality; VR-HMD: head-mounted display for virtual reality; BFM: binocular fusion maintenance; BWFA: binocular open-view Shack-Hartmann wavefront aberrometer.

Light localization with low-contrast targets in a patient implanted with a suprachoroidal-transretinal stimulation retinal prosthesis.

PURPOSE: To evaluate the improvement in targeted reaching movements toward targets of various contrasts in a patient implanted with a suprachoroidal-transretinal stimulation (STS) retinal prosthesis. METHODS: An STS retinal prosthesis was implanted in the right eye of a 42-year-old man with advanced Stargardt disease (visual acuity: right eye, light perception; left eye, hand motion). In localization tests during the 1-year follow-up period, the patient attempted to touch the center of a white square target (visual angle, 10°; contrast, 96, 85, or 74%) displayed at a random position on a monitor. The distance between the touched point and the center of the target (the absolute deviation) was averaged over 20 trials with the STS system on or off. RESULTS: With the left eye occluded, the absolute deviation was not consistently lower with the system on than off for high-contrast (96%) targets, but was consistently lower with the system on for low-contrast (74%) targets. With both eyes open, the absolute deviation was consistently lower with the system on than off for 85%-contrast targets. With the system on and 96%-contrast targets, we detected a shorter response time while covering the right eye, which was being implanted with the STS, compared to covering the left eye (2.41 ± 2.52 vs 8.45 ± 3.78 s, p < 0.01). CONCLUSIONS: Performance of a reaching movement improved in a patient with an STS retinal prosthesis implanted in an eye with residual natural vision. Patients with a retinal prosthesis may be able to improve their visual performance by using both artificial vision and their residual natural vision. CLINICAL TRIAL REGISTRATION: Beginning date of the trial: Feb. 20, 2014 Date of registration: Jan. 4, 2014 Trial registration number: UMIN000012754 Registration site: UMIN Clinical Trials Registry (UMIN-CTR) http://www.umin.ac.jp/ctr/index.htm.

Correction to: Light localization with low-contrast targets in a patient implanted with a suprachoroidal-transretinal stimulation retinal prosthesis.

The original publication of this paper contain an error because of an incorrect captured corresponding author.

Light stability tests of CH3NH3PbI3 perovskite solar cells using porous carbon counter electrodes.

The CH3NH3PbI3 perovskite solar cells have been fabricated using three-porous-layered electrodes as, 〈glass/F-doped tin oxide (FTO)/dense TiO2/porous TiO2-perovskite/porous ZrO2-perovskite/porous carbon-perovskite〉 for light stability tests. Without encapsulation in air, the CH3NH3PbI3 perovskite solar cells maintained 80% of photoenergy conversion efficiency from the initial value up to 100 h under light irradiation (AM 1.5, 100 mW cm-2). Considering the color variation of the CH3NH3PbI3 perovskite layer, the significant improvement of light stability is due to the moisture-blocking effect of the porous carbon back electrodes. The strong interaction between carbon and CH3NH3PbI3 perovskite was proposed by the measurements of X-ray photoelectron spectroscopy and X-ray diffraction of the porous carbon-perovskite layers.

False reaching movements in localization test and effect of auditory feedback in simulated ultra-low vision subjects and patients with retinitis pigmentosa.

PURPOSE: To determine the accuracy of reaching movements with localization tests in subjects with simulated ultra-low vision, and to examine the effectiveness of auditory feedback training in improving the accuracy of the reaching movements. METHODS: Twenty-one subjects with simulated ultra-low vision and three patients with advanced retinitis pigmentosa (RP) were studied with the localization tester. The localization tester had white square targets with a visual angle of 10° that were projected randomly on a computer monitor screen. The subjects or RP patients were instructed to touch the center of the target. Each subject was tested 20 trials. The distance from the center of the target to the point where subjects touched, the deviation, was calculated automatically by the computer. We also examined the effect of auditory feedback on improving the accuracy of reaching movements. RESULTS: The average angle of deviation in the subjects was not significantly correlated with visual acuity. The points touched by subjects with simulated low vision were located downward and horizontally toward the hand they used. They were condensed around the barycenter of the touched points (paired t tests; *p = 0.037). The touched points of the patients also deviated downward and condensed around the barycenter. The deviations decreased significantly with auditory feedback when trained over 100 trials. CONCLUSIONS: The subjects with simulated ultra-low vision and the advanced RP patients had false orientations against the position of localized target systematically. An auditory feedback system may help to correct the false orientations for reaching movements in patients with very low vision.

Surgical feasibility and biocompatibility of wide-field dual-array suprachoroidal-transretinal stimulation prosthesis in middle-sized animals.

PURPOSE: To investigate the safety and efficacy of a newly-developed wide-field dual-array suprachoroidal-transretinal stimulation (STS) prosthesis in middle-sized animals. METHODS: The prosthesis consisted of two arrays with 50 to 74 electrodes. To test the feasibility of implanting the prosthesis and its efficacy, the prosthesis was implanted for 14 days into two rabbits. Optical coherence tomography (OCT) and ophthalmoscopy were performed 7 and 14 days after the implantation. Then the rabbits were euthanized, eyes were enucleated, and the posterior segment of the eye was examined histologically. In a second experiment, the arrays were implanted into two cats, and their ability to elicit neural responses was determined by electrically evoked potentials (EEPs) at the chiasm and by optical imaging of the retina. RESULTS: All arrays were successfully implanted, and no major complications occurred during the surgery or during the 2-week postoperative period. Neither OCT nor ophthalmoscopy showed any major complications or instability of the arrays. Histological evaluations showed only mild cellular infiltration and overall good retinal preservation. Stimulation of the retina by the arrays evoked EEPs recorded from the chiasm. Retinal imaging showed that the electrical pulses from the arrays altered the retinal images indicating an activation of retinal neurons. The thresholds were as low as 100 µA for a chiasm response and 300 µA for the retinal imaging. CONCLUSION: Implantation of a newly-developed dual-array STS prosthesis for 2 weeks in rabbits was feasible surgically, and safe. The results of retinal imaging showed that the dual-array system was able to activate retinal neurons. We conclude that the dual-array design can be implanted without complication and is able to activate retinal neurons and optic nerve axons.

[Reliability and validity of the Japanese version of the DAST-20].

OBJECTIVE: Assessing the degree of problems related to drug abuse is important in each treatment setting. The Drug Abuse Screening Test-20 (DAST-20) is a brief, simple 20-item instrument to measure the degree of problems related to drug use. The objective of the present study is to examine the reliability and validity of the Japanese version of the DAST-20. METHODS: We translated the DAST-20 into Japanese using back translation. The anonymous self-administered questionnaire was completed by 310 drug users at the Drug Addiction Rehabilitation Centers (DARC group, n = 113) and at HIV/AIDS regional hospitals (HIV group, n = 197) in Japan. RESULTS: The average DAST-20 score was 7.6 (DARC group = 14.7, HIV group = 2.8). Each item score was highly correlated with the total score (r = 0.45-0.88). A high internal consistency (Cronbach's α = 0.95) was observed (men = 0.95, women = 0.84). Overall test-retest reliability was 0.86 (men = 0.85, women = 0.90). The total DAST-20 score was strongly positively correlated with the Severity of Dependence Scale-J score (r = 0.85), but moderately positively correlated with the Alcohol Use Disorders Identification Test score (r = 0.41). In addition, confirmatory factor analysis indicated an acceptable fit to the data (goodness-of-fit index [GFI] = 0.893, adjusted goodness-of-fit index [AGFI] = 0.854, comparative fit index [CFI] = 0.948, root mean square residual [RMR] = 0.008, root mean square error of approximation [RMSEA] = 0.073). CONCLUSION: Our results clearly suggest that the Japanese version of the DAST-20 has sufficient internal consistency and acceptable levels of concurrent validity and construct validity.

Shallow-level defect passivation by 6H perovskite polytype for highly efficient and stable perovskite solar cells.

The power conversion efficiency of perovskite solar cells continues to increase. However, defects in perovskite materials are detrimental to their carrier dynamics and structural stability, ultimately limiting the photovoltaic characteristics and stability of perovskite solar cells. Herein, we report that 6H polytype perovskite effectively engineers defects at the interface with cubic polytype FAPbI3, which facilitates radiative recombination and improves the stability of the polycrystalline film. We particularly show the detrimental effects of shallow-level defect that originates from the formation of the most dominant iodide vacancy (VI+) in FAPbI3. Furthermore, additional surface passivation on top of the hetero-polytypic perovskite film results in an ultra-long carrier lifetime exceeding 18 µs, affords power conversion efficiencies of 24.13% for perovskite solar cells, 21.92% (certified power conversion efficiency: 21.44%) for a module, and long-term stability. The hetero-polytypic perovskite configuration may be considered as close to the ideal polycrystalline structure in terms of charge carrier dynamics and stability.

Archetype-Cation-Based Room-Temperature Ionic Liquid: Aliphatic Primary Ammonium Bis(trifluoromethylsulfonyl)imide as a Highly Functional Additive for a Hole Transport Material in Perovskite Solar Cells.

Room-temperature ionic liquids (RTILs) have attracted significant attention owing to their unique nature and a variety of potential applications. The archetypal RTIL comprising an aliphatic primary ammonium was discovered over a century ago, but this cation is seldom used in modern RTILs because other bulky cations (e.g., quaternary ammonium-, pyridine-, and imidazole-based cations) are prominent in current major applications, such as electrolytes and solvents, which require low and/or reversible reactivities. However, although the design of materials should change according to the intended application, RTIL designs remain conventional even when applied in unexplored fields, limiting their functions. Herein, RTIL consisting of an archetypal aliphatic primary ammonium (i.e., n-octylammonium: OA) cation and a modern bis(trifluoromethylsulfonyl)imide (TFSI) anion is proposed and demonstrated as a highly functional additive for a 2,2',7,7'-tetrakis(N,N-di-4-methoxyphenylamino)-9,9'-spirobifluorene (Spiro-OMeTAD), which is the most common hole transport material (HTM), in perovskite solar cells (PSCs). The OA-TFSI additive exhibits prominent functions via permanent reactions of the component ions with the PSC components, thus providing several advantages. The OA cations spontaneously and densely passivate the perovskite layer during the HTM deposition process, leading to both suppression of carrier recombination at the HTM/perovskite interface and hydrophobic perovskite surfaces. Meanwhile, the TFSI anions effectively improve the HTM function most likely via efficient stabilization of the Spiro-OMeTAD radical, enhancing hole collection properties in the PSCs. Consequently, PSC performances involving long-term stability were significantly improved using the OA-TFSI additive. Based on the present results, this study advocates that reconsidering the RTIL design, even when it differs from the current major designs yet is suitable for a target application, can provide functions superior to conventional ones. The insights obtained in this work will spur further study of RTIL designs and aid the development of the broad materials science field including PSCs.

Quantitative evaluation of blinking in blepharospasm using electrooculogram-integrated smart eyeglasses.

Smart eyeglasses with an integrated electrooculogram (EOG) device (JINS MEME ES_R®, JINS Inc.) were evaluated as a quantitative diagnostic tool for blepharospasm. Participants without blepharospasm (n = 21) and patients with blepharospasm (n = 19) undertook two voluntary blinking tests (light and fast) while wearing the smart eyeglasses. Vertical (Vv) and horizontal (Vh) components were extracted from time-series voltage waveforms recorded during 30 s of the blinking tests. Two parameters, the ratio between the maximum and minimum values in the power spectrum (peak-bottom ratio, Fourier transform analysis) and the mean amplitude of the EOG waveform (peak amplitude analysis) were calculated. The mean amplitude of Vh from light and fast blinking was significantly higher in the blepharospasm group than in the control group (P < 0.05 and P < 0.05). Similarly, the peak-bottom ratio of Vv from light and fast blinking was significantly lower in the blepharospasm group than in the control group (P < 0.05 and P < 0.05). The mean amplitude of Vh and peak-bottom ratio of Vv correlated with the scores determined using the Jankovic rating scale (P < 0.05 and P < 0.01). Therefore, these parameters are sufficiently accurate for objective blepharospasm classification and diagnosis.

Pupillary Light Reflex and Multimodal Imaging in Patients With Central Serous Chorioretinopathy.

Purpose: The purpose of this study was to investigate and compare the corresponding alterations of the pupillary response between acute and chronic central serous chorioretinopathy (CSC) and between different disease categories. Methods: We recruited patients with unilateral acute and chronic CSC. An eye tracker was applied to determine the pupillary light reflex (PLR) and evaluate the following PLR metrics in healthy eyes: pupil diameter, diameter changes, including relative constriction amplitude (AMP%), and re-dilation ratio (D1%). Baseline optical coherence tomography (OCT), and fluorescein and indocyanine green angiography (FA/ICGA) were performed to analyze the relationship between pupillary response and retinal/choroidal architecture. Results: In total, 52 patients were enrolled, including 25 with acute CSC and 27 with chronic CSC. Compared to the chronic CSC group, the acute CSC group displayed a significantly larger baseline pupil diameter (BPD; of 5.51 mm, P = 0.015), lower AMP% (34.40%, P = 0.004), and higher D1% (93.01%, P = 0.002), indicating sympathetic overactivity. On OCT, the total macular volume was positively correlated with the D1% (r = 0.48, P = 0.005) and negatively with AMP (r = -0.47, P = 0.007). On ICGA, the intense choroidal vascular hyperpermeability (CVH) group displayed a greater BPD than the nonintense CVH group. Additionally, 9 cases with later recurrent episodes following therapy showed a lower AMP% and higher D1% than the nonrecurrent group. Conclusions: The PLR revealed sympathetic excitation in patients with acute CSC. The stronger D1% was significantly associated with greater total macular volume, and it may be a potential biomarker for predicting the later recurrence of CSC.

Retarding solid-state reactions enable efficient and stable all-inorganic perovskite solar cells and modules.

All-inorganic CsPbI3 perovskite solar cells (PSCs) with efficiencies exceeding 20% are ideal candidates for application in large-scale tandem solar cells. However, there are still two major obstacles hindering their scale-up: (i) the inhomogeneous solid-state synthesis process and (ii) the inferior stability of the photoactive CsPbI3 black phase. Here, we have used a thermally stable ionic liquid, bis(triphenylphosphine)iminium bis(trifluoromethylsulfonyl)imide ([PPN][TFSI]), to retard the high-temperature solid-state reaction between Cs4PbI6 and DMAPbI3 [dimethylammonium (DMA)], which enables the preparation of high-quality and large-area CsPbI3 films in the air. Because of the strong Pb-O contacts, [PPN][TFSI] increases the formation energy of superficial vacancies and prevents the undesired phase degradation of CsPbI3. The resulting PSCs attained a power conversion efficiency (PCE) of 20.64% (certified 19.69%) with long-term operational stability over 1000 hours. A record efficiency of 16.89% for an all-inorganic perovskite solar module was achieved, with an active area of 28.17 cm2.

Foldable Hole-Transporting Materials for Merging Electronic States between Defective and Perfect Perovskite Sites.

Defective and perfect sites naturally exist within electronic semiconductors, and considerable efforts to reduce defects to improve the performance of electronic devices, especially in hybrid organic-inorganic perovskites (ABX3 ), are undertaken. Herein, foldable hole-transporting materials (HTMs) are developed, and they extend the wavefunctions of A-site cations of perovskite, which, as hybridized electronic states, link the trap states (defective site) and valence band edge (perfect site) between the naturally defective and perfect sites of the perovskite surface, finally converting the discrete trap states of the perovskite as the continuous valence band to reduce trap recombination. Tailoring the foldability of the HTMs tunes the wavefunctions between defective and perfect surface sites, allowing the power conversion efficiency of a small cell to reach 23.22% and that of a mini-module (6.5 × 7 cm, active area = 30.24 cm2 ) to reach as high as 21.71% with a fill factor of 81%, the highest value reported for non-spiro-OMeTAD-based perovskite solar modules.