Multimodal X-ray probe station at 9C beamline of Pohang Light Source-II.

In this study, the conceptual design and performance of a multimodal X-ray probe station recently installed at the 9C coherent X-ray scattering beamline of the Pohang Light Source-II are presented. The purpose of this apparatus is to measure coherent X-ray diffraction, X-ray fluorescence and electrical properties simultaneously. A miniature vacuum probe station equipped with a four-point probe was mounted on a six-axis motion hexapod. This can be used to study the structural and chemical evolution of thin films or nanostructures, as well as device performance including electronic transport properties. This probe station also provides the capability of varying sample environments such as gas atmosphere using a mass-flow-control system and sample temperatures up to 600°C using a pyrolytic boron nitride heater. The in situ annealing of ZnO thin films and the performance of ZnO nanostructure-based X-ray photodetectors are discussed. These results demonstrate that a multimodal X-ray probe station can be used for performing in situ and operando experiments to investigate structural phase transitions involving electrical resistivity switching.

Oxidation-induced three-dimensional morphological changes in Ni nanoparticles observed by coherent X-ray diffraction imaging.

Three-dimensional structures of Ni nanoparticles undergoing significant morphological changes on oxidation were observed non-destructively using coherent X-ray diffraction imaging. The Ni particles were oxidized into Ni1O1 while forming pores of various sizes internally. For each Ni nanoparticle, one large void was identified at a lower corner near the interface with the substrate. The porosity of the internal region of the agglomerated Ni oxide was about 38.4%. Regions of high NiO density were mostly observed at the outer crust of the oxide or at the boundary with the large voids. This research expands our understanding of general catalytic reactions with direct observation of oxidation-induced nanoscale morphological changes.

Phase separated bi-metallic PtNi nanoparticles formed by pulsed laser dewetting.

We present morphological and compositional analysis of phase-separated Pt-Ni alloy nanoparticles (NPs) formed by ns pulsed laser dewetting. The PtNi NPs obtained by the pulsed laser dewetting consist of phase-separated multiple domains including Pt3Ni, PtNi and PtNi3 phases with various crystal orientations as revealed by transmission electron microscopy, which is in contrast to thermal dewetting resulting NPs of a uniform composition. A three-dimensional (3D) electron density map of a dewetted PtNi NP obtained using the coherent x-ray diffraction microscopy elucidates the 3D morphology of Pt- and Ni-rich regions together with a nano-cavity formed during the pulsed laser irradiation.

Laser-induced metastable mixed phase of AuNi nanoparticles: a coherent X-ray diffraction imaging study.

The laser annealing process for AuNi nanoparticles has been visualized using coherent X-ray diffraction imaging (CXDI). AuNi bimetallic alloy nanoparticles, originally phase separated due to the miscibility gap, transform to metastable mixed alloy particles with rounded surface as they are irradiated by laser pulses. A three-dimensional CXDI shows that the internal part of the AuNi particles is in the mixed phase with preferred compositions at ∼29 at% of Au and ∼90 at% of Au.

Direct nano-scale patterning of Ag films using hard X-ray induced oxidation.

The morphological change of silver nano-particles (AgNPs) exposed to an intense synchrotron X-ray beam was investigated for the purpose of direct nano-scale patterning of metal thin films. AgNPs irradiated by hard X-rays in oxygen ambient were oxidized and migrated out of the illuminated region. The observed X-ray induced oxidation was utilized to fabricate nano-scale metal line patterns using sectioned WSi2/Si multilayers as masks. Lines with a width as small as 21 nm were successfully fabricated on Ag films on silicon nitride. Au/Ag nano-lines were also fabricated using the proposed method.

Direct-write X-ray lithography using a hard X-ray Fresnel zone plate.

Results are reported of direct-write X-ray lithography using a hard X-ray beam focused by a Fresnel zone plate with an outermost zone width of 40 nm. An X-ray beam at 7.5 keV focused to a nano-spot was employed to write arbitrary patterns on a photoresist thin film with a resolution better than 25 nm. The resulting pattern dimension depended significantly on the kind of underlying substrate, which was attributed to the lateral spread of electrons generated during X-ray irradiation. The proximity effect originated from the diffuse scattering near the focus and electron blur was also observed, which led to an increase in pattern dimension. Since focusing hard X-rays to below a 10 nm spot is currently available, the direct-write hard X-ray lithography developed in this work has the potential to be a promising future lithographic method.

Fresnel coherent diffractive imaging of elemental distributions in nanoscale binary compounds.

We report quantitative determination of elemental distribution in binary compounds with nano meter scale spatial resolution using x-ray Fresnel coherent diffractive imaging (FCDI). We show that the quantitative magnitude and phase values of the x-ray wave exiting an object determined by FCDI can be utilized to obtain full-field atomic density maps of each element independently. The proposed method was demonstrated by reconstructing the density maps of Pt and NiO in a Pt-NiO binary compound with about 18 nm spatial resolution.

Resolution enhancement in coherent x-ray diffraction imaging by overcoming instrumental noise.

We report that reference objects, strong scatterers neighboring weak phase objects, enhance the phase retrieval and spatial resolution in coherent x-ray diffraction imaging (CDI). A CDI experiment with Au nano-particles exhibited that the reference objects amplified the signal-to-noise ratio in the diffraction intensity at large diffraction angles, which significantly enhanced the image resolution. The interference between the diffracted x-ray from reference objects and a specimen also improved the retrieval of the phase of the diffraction signal. The enhancement was applied to image NiO nano-particles and a mitochondrion and confirmed in a simulation with a bacteria phantom. We expect that the proposed method will be of great help in imaging weakly scattering soft matters using coherent x-ray sources including x-ray free electron lasers.

Single-pulse coherent diffraction imaging using soft x-ray laser.

We report a coherent diffraction imaging (CDI) using a single 8 ps soft x-ray laser pulse at a wavelength of 13.9 nm. The soft x-ray pulse was generated by a laboratory-scale intense pumping laser providing coherent x-ray pulses up to the level of 10(11) photons/pulse. A spatial resolution below 194 nm was achieved with a single pulse, and it was shown that a resolution below 55 nm is feasible with improved detector capability. The single-pulse CDI might provide a way to investigate dynamics of nanoscale molecules or particles.

Two dimensional hard x-ray nanofocusing with crossed multilayer Laue lenses.

Hard x-ray microscopy with nanometer resolution will open frontiers in the study of materials and devices, environmental sciences, and life sciences by utilizing the unique characterization capabilities of x-rays. Here we report two-dimensional nanofocusing by multilayer Laue lenses (MLLs), a type of diffractive optics that is in principle capable of focusing x-rays to 1 nm. We demonstrate focusing to a 25 × 27 nm(2) FWHM spot with an efficiency of 2% at a photon energy of 12 keV, and to a 25 × 40 nm(2) FWHM spot with an efficiency of 17% at a photon energy of 19.5 keV.

Nanoscale Soft Wetting Observed in Co/Sapphire during Pulsed Laser Irradiation.

Liquid drops on deformable soft substrates exhibit quite complicated wetting behavior as compared to those on rigid solid substrates. We report on a soft wetting behavior of Co nanoparticles (NPs) on a sapphire substrate during pulsed laser-induced dewetting (PLID). Co NPs produced by PLID wetted the sapphire substrate with a contact angle near 70°, which is in contrast to typical dewetting behavior of metal thin films exhibiting contact angles greater than 90°. In addition, a nanoscale γ-Al2O3 wetting ridge about 15 nm in size and a thin amorphous Al2O3 interlayer were observed around and beneath the Co NP, respectively. The observed soft wetting behavior strongly indicates that the sapphire substrate became soft and deformable during PLID. Moreover, the soft wetting was augmented under PLID in air due to the formation of a CoO shell, resulting in a smaller contact angle near 30°.

Observation of the Talbot effect using broadband hard x-ray beam.

We demonstrated the Talbot effect using a broadband hard x-ray beam (Δλ/λ ~1). The exit wave-field of the x-ray beam passing through a grating with a sub micro-meter scale period was successfully replicated and recorded at effective Talbot distance, Z(T). The period was reduced to half at Z(T)/4 and 3/4Z(T), and the phase reversal was observed at Z(T)/2. The propagating wave-field recorded on photoresists was consistent with a simulated result.

Wedged multilayer Laue lens.

A multilayer Laue lens (MLL) is an x-ray focusing optic fabricated from a multilayer structure consisting of thousands of layers of two different materials produced by thin-film deposition. The sequence of layer thicknesses is controlled to satisfy the Fresnel zone plate law and the multilayer is sectioned to form the optic. An improved MLL geometry can be created by growing each layer with an in-plane thickness gradient to form a wedge, so that every interface makes the correct angle with the incident beam for symmetric Bragg diffraction. The ultimate hard x-ray focusing performance of a wedged MLL has been predicted to be significantly better than that of a nonwedged MLL, giving subnanometer resolution with high efficiency. Here, we describe a method to deposit the multilayer structure needed for an ideal wedged MLL and report our initial deposition results to produce these structures.

Sectioning of multilayers to make a multilayer Laue lens.

We report a process to fabricate multilayer Laue lenses (MLL's) by sectioning and thinning multilayer films. This method can produce a linear zone plate structure with a very large ratio of zone depth to width (e.g., >1000), orders of magnitude larger than can be attained with photolithography. Consequently, MLL's are advantageous for efficient nanofocusing of hard x rays. MLL structures prepared by the technique reported here have been tested at an x-ray energy of 19.5 keV, and a diffraction-limited performance was observed. The present article reports the fabrication techniques that were used to make the MLL's.

Efficient low-temperature transparent electrocatalytic layers based on graphene oxide nanosheets for dye-sensitized solar cells.

Electrocatalytic materials with a porous structure have been fabricated on glass substrates, via high-temperature fabrication, for application as alternatives to platinum in dye-sensitized solar cells (DSCs). Efficient, nonporous, nanometer-thick electrocatalytic layers based on graphene oxide (GO) nanosheets were prepared on plastic substrates using electrochemical control at low temperatures of ≤100 °C. Single-layer, oxygen-rich GO nanosheets prepared on indium tin oxide (ITO) substrates were electrochemically deoxygenated in acidic medium within a narrow scan range in order to obtain marginally reduced GO at minimum expense of the oxygen groups. The resulting electrochemically reduced GO (E-RGO) had a high density of residual alcohol groups with high electrocatalytic activity toward the positively charged cobalt-complex redox mediators used in DSCs. The ultrathin, alcohol-rich E-RGO layer on ITO-coated poly(ethylene terephthalate) was successfully applied as a lightweight, low-temperature counter electrode with an extremely high optical transmittance of ∼97.7% at 550 nm. A cobalt(II/III)-mediated DSC employing the highly transparent, alcohol-rich E-RGO electrode exhibited a photovoltaic power conversion efficiency of 5.07%. This is superior to that obtained with conventionally reduced GO using hydrazine (3.94%) and even similar to that obtained with platinum (5.10%). This is the first report of a highly transparent planar electrocatalytic layer based on carbonaceous materials fabricated on ITO plastics for application in DSCs.

Racial Disparities in Postoperative Complications After Radical Nephrectomy: A Population-based Analysis.

OBJECTIVE: To perform a population-based study that evaluates contemporary racial disparities in the morbidity profile of patients undergoing radical nephrectomy in the United States. METHODS: Using the Premier hospital database (Premier Inc, Charlotte, NC), which collects data from over 600 nonfederal hospitals throughout the United States, we identified patients undergoing a total nephrectomy as their primary procedure and also had a concurrent diagnosis of a kidney mass or cancer from 2003 to 2010. The primary outcome was 90-day major complication rates, based on the Clavien classification system. Multivariate logistic regression models were performed, adjusting for clustering by hospitals and survey weighting to ensure nationally representative estimates. RESULTS: The study population included 25,517 patients translating into a weighted sample of 185,135 radical nephrectomies. In a multivariate model including patient, hospital, and surgical characteristics, blacks were more commonly associated with a major complication (odds ratio, 2.1; P <.0001). When we incorporated Charlson comorbidity score into the model, the racial disparity in major complications was attenuated by 36% (odds ratio, 1.7; P <.0001). Adjusting for annual surgical volume in the multivariate model did not alter results. CONCLUSION: Our contemporary evaluation of patients undergoing radical nephrectomy in the United States demonstrates that blacks are associated with a markedly elevated rate of major complications as compared to whites. This disparity is possibly a result of unequal access to routine health care.

Quantitative x-ray phase imaging at the nanoscale by multilayer Laue lenses.

For scanning x-ray microscopy, many attempts have been made to image the phase contrast based on a concept of the beam being deflected by a specimen, the so-called differential phase contrast imaging (DPC). Despite the successful demonstration in a number of representative cases at moderate spatial resolutions, these methods suffer from various limitations that preclude applications of DPC for ultra-high spatial resolution imaging, where the emerging wave field from the focusing optic tends to be significantly more complicated. In this work, we propose a highly robust and generic approach based on a Fourier-shift fitting process and demonstrate quantitative phase imaging of a solid oxide fuel cell (SOFC) anode by multilayer Laue lenses (MLLs). The high sensitivity of the phase to structural and compositional variations makes our technique extremely powerful in correlating the electrode performance with its buried nanoscale interfacial structures that may be invisible to the absorption and fluorescence contrasts.

Oxidation of PtNi nanoparticles studied by a scanning X-ray fluorescence microscope with multi-layer Laue lenses.

We report a study of the oxidation process of individual PtNi nanoparticles (NPs) conducted with a novel scanning multi-layer Laue lens X-ray microscope. The elemental maps reveal that alloyed PtNi NPs were transformed into Pt/NiO core-shell NPs by thermal oxidation. The observations furthermore indicate that a coalescence of Pt/NiO core-shell NPs occurred during oxidation.

Progression of prostate cancer despite an extremely low serum level of prostate-specific antigen.

A 61-year-old man who had been diagnosed with prostate cancer 9 years ago and had been treated with pelvic irradiation and intermittent androgen deprivation therapy visited the emergency room because of back pain and weakness in both legs. Spine magnetic resonance imaging showed a lumbar epidural mass and spine metastasis. The whole-body workup revealed multiple metastases to the lymph nodes, bone, liver, and lung. The serum prostate-specific antigen was 0.02 ng/ml. He underwent laminectomy, posterior fixation, and epidural mass excision, and metastatic adenocarcinoma from the prostate was diagnosed. The patient underwent 1 cycle of docetaxel-based chemotherapy. More chemotherapy could not be done because of his general weakness. The patient died one month later of multiple organ failure.

Obesity and hepatocellular carcinoma.

Epidemiological studies have shown that obesity is a risk factor for hepatocellular carcinoma. Similar studies further indicate that diabetes is also a major risk factor. Both obesity and diabetes are frequently associated with nonalcoholic fatty liver disease, and case reports have shown progression of nonalcoholic fatty liver disease to cirrhosis and hepatocellular carcinoma. Although no study has clearly tied all of these variables together, it is likely that the association of hepatocellular carcinoma with obesity represents the progression of underlying nonalcoholic fatty liver disease to cirrhosis. The mechanism most likely involves replicative senescence of steatotic mature hepatocytes and compensatory hyperplasia of progenitor (oval) cells as a reaction to chronic injury due to ongoing nonalcoholic steatohepatitis and resultant hepatic fibrosis. Growth factors associated with chronic inflammation, type 2 diabetes, and DNA mutations as a result of lipid peroxidation probably play significant roles in clonal expansion and hepatocellular carcinoma progression. It remains unclear whether cirrhosis is a prerequisite for the development of hepatocellular carcinoma or whether hepatocellular carcinoma can develop in fatty liver in the absence of cirrhosis. However, well-documented case reports suggest that most cases of hepatocellular carcinoma arise in the setting of nonalcoholic steatohepatitis with cirrhosis. Whether therapy aimed at nonalcoholic fatty liver disease reduces the risk of hepatocellular carcinoma remains to be shown. Prophylactic measures and the role of cancer surveillance have not been adequately investigated, but current evidence suggests a risk for hepatocellular carcinoma in nonalcoholic steatohepatitis-related cirrhosis that rivals that of hepatocellular carcinoma in hepatitis C virus-related cirrhosis, particularly in older male patients.