Angular dependence of the transverse Raman scattering in KDP and DKDP in geometries suitable for beam polarization control.

The angular dependance of the transverse Raman scattering in potassium dihydrogen phosphate (KDP) and its deuterated analogue (DKDP) for the entire range of crystal configurations suitable for laser beam polarization control has been investigated via experimental and modeling tools. This work was made possible by simultaneously rotating a spherical sample and the pump polarization to effectively measure the angular dependance of the transverse Raman signal in 360°. This novel method, which is applicable for the investigation of the Raman scattering in optically anisotropic materials, demonstrates that the spontaneous Raman scattering signal exhibits strong angular dependence that is modulated by depolarization and polarization rotation effects generated as the Raman signal traverses the material due to its birefringence. The results show that the total signal generated by the pump beam is the sum of the signals generated by the two components that have polarization parallel and orthogonal to the optic axis. The peak signal intensity, which is of importance for high-power laser applications, depends on the orientation of the optic axis and can vary by a factor of about 2. The excellent agreement between experimental data and modeling results validates the associated models and enables one to consider optimal crystal cut designs for specific applications.

Mechanisms of picosecond laser-induced damage in common multilayer dielectric gratings.

The modifications of multilayer dielectric (MLD) gratings arising from laser-induced damage using 0.6-ps and 10-ps laser pulses at 1053 nm are investigated to better understand the damage-initiation mechanisms. Upon damage initiation, sections of the affected grating pillars are removed, thereby erasing the signature of the underlying mechanisms of laser damage. To address this issue, we performed paired studies using macroscopic grating-like features that are 5 mm in width to reveal the laser-damage morphology of the different grating sections: pillar side wall, sole, and pillar top. The results suggest that, similarly to MLD coatings, there are two damage-initiation mechanisms corresponding to the different pulse durations.

Simulation of internal stress waves generated by laser-induced damage in multilayer dielectric gratings.

Multilayer dielectric (MLD) gratings used in ultrahigh-intensity laser systems often exhibit a laser-induced damage performance below that of their constituent materials. Reduced performance may arise from fabrication- and/or design-related issues. Finite element models were developed to simulate stress waves in MLD grating structures generated by laser-induced damage events. These models specifically investigate the influence of geometric and material parameters on how stress waves can lead to degradation of material structural integrity that can have adverse effects on its optical performance under subsequent laser irradiation: closer impedance matching of the layer materials reduces maximum interface stresses by ~20% to 30%; increasing sole thickness from 50 nm to 500 nm reduces maximum interface stresses by ~50%.

Publisher's Note: Demonstration of Fuel Hot-Spot Pressure in Excess of 50 Gbar for Direct-Drive, Layered Deuterium-Tritium Implosions on OMEGA [Phys. Rev. Lett. 117, 025001 (2016)].

This corrects the article DOI: 10.1103/PhysRevLett.117.025001.

Demonstration of Fuel Hot-Spot Pressure in Excess of 50 Gbar for Direct-Drive, Layered Deuterium-Tritium Implosions on OMEGA.

A record fuel hot-spot pressure P_{hs}=56±7 Gbar was inferred from x-ray and nuclear diagnostics for direct-drive inertial confinement fusion cryogenic, layered deuterium-tritium implosions on the 60-beam, 30-kJ, 351-nm OMEGA Laser System. When hydrodynamically scaled to the energy of the National Ignition Facility, these implosions achieved a Lawson parameter ∼60% of the value required for ignition [A. Bose et al., Phys. Rev. E 93, 011201(R) (2016)], similar to indirect-drive implosions [R. Betti et al., Phys. Rev. Lett. 114, 255003 (2015)], and nearly half of the direct-drive ignition-threshold pressure. Relative to symmetric, one-dimensional simulations, the inferred hot-spot pressure is approximately 40% lower. Three-dimensional simulations suggest that low-mode distortion of the hot spot seeded by laser-drive nonuniformity and target-positioning error reduces target performance.

Electron-beam-deposited distributed polarization rotator for high-power laser applications.

Electron-beam deposition of silica and alumina is used to fabricate distributed polarization rotators suitable for smoothing the intensity of large-aperture, high-peak-power lasers. Low-modulation, low-loss transmittance with a high 351-nm laser-damage threshold is achieved.

Laser-beam zooming to mitigate crossed-beam energy losses in direct-drive implosions.

Spherically symmetric direct-drive-ignition designs driven by laser beams with a focal-spot size nearly equal to the target diameter suffer from energy losses due to crossed-beam energy transfer (CBET). Significant reduction of CBET and improvements in implosion hydrodynamic efficiency can be achieved by reducing the beam diameter. Narrow beams increase low-mode perturbations of the targets because of decreased illumination uniformity that degrades implosion performance. Initiating an implosion with nominal beams (equal in size to the target diameter) and reducing the beam diameter by ∼ 30%-40% after developing a sufficiently thick target corona, which smooths the perturbations, mitigate CBET while maintaining low-mode target uniformity in ignition designs with a fusion gain ≫ 1.

Observation of strong oscillations of areal mass in an unsupported shock wave.

An experimental study of hydrodynamic perturbation evolution in a strong unsupported shock wave, which is immediately followed by an expansion wave, is reported. A planar solid plastic target rippled on the front side is irradiated with a 350-450 ps long laser pulse. The perturbation evolution in the target is observed using face-on monochromatic x-ray radiography during and for up to 4 ns after the laser pulse. The theoretically predicted large oscillations of the areal mass in the target are observed for the first time. Multiple phase reversals of the areal mass modulation are detected.

Measurement of the angular dependence of the spontaneous Raman scattering in anisotropic crystalline materials using spherical samples: Potassium dihydrogen phosphate as a case example.

A specialized experimental configuration was developed to allow for more-accurate characterization of the spontaneous Raman scattering properties in anisotropic materials. This need stems from the challenges, arising from the complexity of light propagation, in obtaining accurate measurements of the angular dependence of the Raman scattering cross section in birefringent materials. The nonlinear optical material KH2PO4 (KDP) is used as a model medium. This study is motivated by the need to improve our understanding and management of transverse stimulated Raman scattering in KDP crystals and its deuterated analog, DKDP, typically used for frequency conversion and polarization control in large-aperture laser systems. Key to this experimental platform is the use of high-quality spherical samples that enable one to measure the Raman scattering cross section in a wide range of geometries using only a single sample. The effect of polarization rotation of both the pump light and the collected Raman signal must be carefully considered in data analysis and can give rise to artifacts, which can, in part, be mitigated by reducing the input and collection cone angles.

Determination of the Raman polarizability tensor in the optically anisotropic crystal potassium dihydrogen phosphate and its deuterated analog.

The Raman tensor of the dominant A1 modes of the nonlinear optical crystalline material potassium dihydrogen phosphate and its 70% deuterated analog have been ascertained. Challenges in determining the A1 mode tensor element values based on previous reports have been resolved using a specially designed experimental setup that makes use of spherical crystal samples. This novel experimental design enabled the determination of measurement artifacts, including polarization rotation of the pump and/or scattered light propagating through the sample and the contribution of additional overlapping phonon modes, which have hindered previous efforts. Results confirmed that the polarization tensor is diagonal, and matrix elements were determined with high accuracy.

Inferred UV fluence focal-spot profiles from soft x-ray pinhole-camera measurements on OMEGA.

A method was developed with laser-irradiated Au planar foils to characterize the focal spot of UV laser beams on a target at full energy from soft x-ray emission. A pinhole camera with a back-thinned charge-coupled device detector and filtration with thin Be and Al foil filters provides images of the x-ray emission at photon energies <2 keV. This method requires a careful measurement of the relationship between the applied UV fluence and the x-ray signal, which can be described by a power-law dependence. The measured exponent γ ∼ 2 provides a dynamic range of ∼25 for the inferred UV fluence. UV fluence profiles of selected beams were measured for 100-ps and 1-ns laser pulses and were compared to directly measured profiles from an UV equivalent-target-plane diagnostic. The inferred spot size and super-Gaussian order from the x-ray technique agree within several percent with the values measured with the direct UV measurements.

Phase-locked control of tiled-grating assemblies for chirped-pulse-amplified lasers using a Mach-Zehnder interferometer.

Multikilojoule petawatt lasers using chirped-pulse amplification are being constructed worldwide. Several systems have adopted a tiled-grating approach to meet the size requirements for the compression gratings. Grating tiles need to be precisely phased to ensure a transform-limited focal spot when focusing high-energy laser pulses in the target plane. A computer-control test system that uses a Mach-Zehnder interferometer capable of monitoring and correcting drift in the tiled-grating assemblies within the compressor is described. The differential errors due to eight gratings, within a compressor with four grating assemblies, were compensated by adjusting a single grating.

[Effects of Maitland's manual mobilization on the thoracic spine]. / Auswirkungen einer manuellen Mobilisation nach Maitland auf die Brustwirbelsäule.

The goal of manual therapy is to decrease pain and to increase function of the spine and peripheral joints. The method introduced by Maitland is widely used in manual medicine. However, no objective changes in the mobility of the thoracic spine after performing manual mobilization have been published in the literature. The aim of this study is to reveal possible changes in the segmental mobility of the thoracic spine after posterior-anterior manipulations without thrust in comparison with a control group. In addition, significant changes within the treatment group were examined. Thirty-six volunteers were randomized into an intervention (16) and a control group (20). The intervention group was treated two times a week for three weeks. The control group received no treatment. The mobility was objectively measured by using Medimouse. No significant difference in the mobility of the thoracic spine could be shown within the intervention group and in comparison with the control group.

Transpeptidation during the analytical proteolysis of proteins.

Since peptide mapping with proteolytic enzymes such as trypsin and Staphylococcus aureus V8 protease is a powerful tool for the characterization of proteins, investigators should be cognizant of possible artifacts due to the technique itself. This article describes the identification of minor peaks found in the maps of recombinant human relaxin and insulin-like growth factor I as transpeptidation products. Both proteins have some homology to insulin with relaxin being composed of two chains designated A and B, while insulin-like growth factor I is composed of a single polypeptide chain. Digestion of relaxin with trypsin at pH 7.2 yields two peptides, T2,3(A10-18) and T7(B10-13), linked together by a disulfide bond. An unexpected component at a 10% level was identified to be the T2-T7 peptide pair where T3(ArgA18) has formed a peptide bond with the amino-terminal LeuB10 of the T7 peptide. It was also observed that the digestion of insulin-like growth factor I with V8 protease normally yields two peptides V4(13-20) and V9(59-70) linked by a disulfide bridge. A minor peak at a 1 to 2% level was identified to be a single polypeptide resulting from the formation of a peptide bond between the amino-terminal Met59 of V9 and the carboxyl-terminal Asp20 of V4, with the disulfide bond intact. These transpeptidation products were isolated by reversed-phase HPLC and identified using amino-terminal sequence and mass spectrometric analyses.

Design of continuous surface-relief phase plates by surface-based simulated annealing to achieve control of focal-plane irradiance.

High-performance phase plates are of vital concern for controlling the far-field irradiance of laser-fusion systems. Several designs for solving this difficult problem have been reported in Optics Letters [e. g., S. N. Dixit et al., Opt. Lett. 19, 417 (1994)]. We report a surface-based form of simulated annealing that significantly improves the irradiance control while eliminating the high-scatter problems that have plagued other methods.

Raman scattering in air: four-dimensional analysis.

Inertial confinement fusion requires propagation of high-intensity, pulse-shaped IR and UV laser beams through long air paths. Such beams are subject to energy losses and decreased beam quality as a result by stimulated rotational Raman scattering (SRRS). In this paper we describe how quantum fluctuations, stimulated Raman amplification, diffraction propagation, and optical aberrations interact during the propagation of short, high-power laser pulses using a four-dimensional (4-D) model of the optical beams and the medium. The 4-D model has been incorporated into a general optical-propagation computer program that allows the entire optical system to be modeled and that is implemented on high-end personal computers, workstations, and supercomputers. The numerical model is used to illustrate important phenomena in the evolution of the optical beams. In addition, the OMEGA Upgrade laser system is used as a design case to illustrate the various considerations for inertial confinement fusion laser design.

Distributed phase plates for super-Gaussian focal-plane irradiance profiles.

The design of phase plates based on a phase-retrieval algorithm has been shown to be successful in achieving high order super-Gaussian distributions in the far field; however, these phase plates exhibit wide-angle scattering losses due to phase discontinuities. We report that, by starting with a distributed phase plate that is a strictly continuous surface and using only a few cycles of a phase-retrieval algorithm, we have obtained good fourth-order super-Gaussian fit and lower scattering loss.

Single-beam, ponderomotive-optical trap for free electrons and neutral atoms.

A ponderomotive-optical trap for energetic free electrons has been generated with a single, high-peak-power laser beam. The focal region consists of an intensity minimum at the center of the focus, with increasing intensities in all directions. The focus can be generated with a two-zone binary phase plate, or with a novel, coaxially segmented wave plate. This scheme can also be used to trap neutral atoms.

TEM(00)-mode and single-longitudinal-mode laser operation with a cholesteric liquid-crystal laser end mirror.

We describe the unique properties of a cholesteric liquid crystal as a laser end mirror. We show how it gives rise to TEM(00)-mode operation as well as single-longitudinal-mode operation of a solid-state laser resonator.

Use of recombinant DNA derived human relaxin to probe the structure of the native protein.

This report describes the physical, chemical, and biological characterization of recombinant human relaxin (rhRlx) used as a probe to establish the disulfide pairing in native human relaxin. This strategy is necessary since native human relaxin is only available in the nanogram range. The relaxin molecule is composed of two nonidentical peptide chains, an A-chain 24 amino acids in length and a B-chain of 29 amino acids, linked by two disulfide bridges with an additional disulfide linkage in the A-chain. Native relaxin isolated from human corpora lutea was compared to rhRlx by reversed-phase chromatography, partial sequence analysis, mass spectroscopy, and bioassay. The potency of rhRlx was established by its ability to stimulate cAMP from primary human uterine endometrial cells. Native relaxin isolated from human corpora lutea was equipotent to chemically synthesized relaxin, which in turn was equipotent to rhRlx. A tryptic map was developed for rhRlx to confirm the complete amino acid sequence and assignment of the disulfide bonds. The three disulfide bonds (CysA10-CysA15, CysA11-CysB11, and CysA24-CysB23) were assigned by mass spectrometric analysis of the tryptic peptides and by comparison to chemically synthesized peptides disulfide linked in the two most probable configurations. In addition, the observed amino acid composition and sequence of rhRlx was in agreement with that predicted from the cDNA sequence with the exception that the A-chain amino terminal was pyroglutamic acid. The migration of rhRlx upon sodium dodecyl sulfate-polyacrylamide gel electrophoresis was consistent with a monomeric structure, and the identity of the band was demonstrated by immunoblotting.