Synergism in TiO2 photocatalytic ozonation for the removal of dichloroacetic acid and thiacloprid.

The synergistic effect of the photocatalytic ozonation process (PH-OZ) using the photocatalyst TiO2 is usually attributed to influences of the physicochemical properties of the catalyst, pollutant type, pH, temperature, O3 concentration, and other factors. It is also often claimed that good adsorption on the TiO2 surface is beneficial for the occurrence of synergism. Herein, we tested these assumptions by using five different commercial TiO2 photocatalysts (P25, PC500, PC100, PC10 and JRC-TiO-6) in three advanced oxidation systems - photocatalysis (O2/TiO2/UV), catalytic ozonation (O3/TiO2) and PH-OZ (O3/TiO2/UV) - for the degradation of two pollutants (dichloroacetic acid - DCAA and thiacloprid) simultaneously present in water. The synergistic effect in PH-OZ was much more pronounced in the case of thiacloprid, a molecule with low adsorption on the surface of the catalyst - in contrast to DCAA with stronger adsorption. The faster kinetics of catalytic ozonation (O3/TiO2) correlated with the higher exposed surface area of TiO2 agglomerates, independent of the (lower) BET surfaces of the primary particles. Nevertheless, DCAA mineralization on the TiO2 surface was much faster than thiacloprid degradation in solution. Therefore, we propose that a high BET surface area of the photocatalyst is crucial for fast surface reactions (DCAA mineralization), while good dispersion - the high exposed surface area of the (small) agglomerates - and charge separation play an important role in photocatalytic degradation or PH-OZ of less adsorbed organic pollutants (thiacloprid).

Photocatalytic and Antimicrobial Activity of Printed Hybrid Titania/Silica Layers.

Stable mixed dispersion of TiO2 and SiO2 was developed and hybrid TiO2/SiO2 layers were fabricated by the direct inkjet patterning technique. The prepared layers were tested for photoinduced hydrophilicity and their photocatalytic activity was tested using stearic acid and dichloroindophenol as model compounds. The antimicrobial activity of prepared layers was tested and evaluated by the traditional plate counting method according to ISO 27447:2009, using Escherichia coli CCM 3988. Material printing proved to be well suited for the deposition of this complex nanoparticulate ink and samples with variable thickness were conveniently fabricated. Printed layers are able to change their surface properties from hydrophobic to superhydrophilic and also decompose the model contaminants rapidly.

Design and evaluation of a compact photocatalytic reactor for water treatment.

A compact reactor for photocatalytic oxidation and photocatalytic ozonation water treatment was developed and evaluated by using four model pollutants. Additionally, combinations of pollutants were evaluated. Specially produced Al2O3 porous reticulated monolith foams served as TiO2 carriers, offering a high surface area support. UV lamps were placed in the interior to achieve reduced dimensions of the reactor (12 cm in diameter × 20 cm in height). Despite its small size, the overall photocatalytic cleaning capacity was substantial. It was evaluated by measuring the degradation of LAS + PBIS and RB19 as representatives of surfactants and textile dyes, respectively. These contaminants are commonly found in household grey wastewater with phenol as a trace contaminant. Three different commercial photocatalysts and one mixture of photocatalysts (P25, P90, PC500 and P25 + PC500) were introduced in the sol-gel processing and immobilized on foamed Al2O3 monoliths. RB19 and phenol were easily degradable, while LAS and PBIS were more resistant. The experiments were conducted at neutral-acidic pH because alkaline pH negatively influences both photocatalyic ozonation (PCOZ) and photocatalysis. The synergistic effect of PCOZ was generally much more expressed in mineralization reactions. Total organic carbon TOC half lives were in the range of between 13 and 43 min in the case of individual pollutants in double-deionized water. However, for the mixed pollutants in tap water, the TOC half-life only increased to 53 min with the most efficient catalyst (P90). In comparison to photocatalysis, the PCOZ process is more suitable for treating wastewater with a high loading of organic pollutants due to its higher cleaning capacity. Therefore, PCOZ may prove more effective in industrial applications.

Solar-driven photocatalytic treatment of diclofenac using immobilized TiO2-based zeolite composites.

The study is aimed at evaluating the potential of immobilized TiO2-based zeolite composite for solar-driven photocatalytic water treatment. In that purpose, TiO2-iron-exchanged zeolite (FeZ) composite was prepared using commercial Aeroxide TiO2 P25 and iron-exchanged zeolite of ZSM5 type, FeZ. The activity of TiO2-FeZ, immobilized on glass support, was evaluated under solar irradiation for removal of diclofenac (DCF) in water. TiO2-FeZ immobilized in a form of thin film was characterized for its morphology, structure, and composition using scanning electron microscopy/energy-dispersive x-ray spectroscopy (SEM/EDX). Diffuse reflectance spectroscopy (DRS) was used to determine potential changes in band gaps of prepared TiO2-FeZ in comparison to pure TiO2. The influence of pH, concentration of hydrogen peroxide, FeZ wt% within the composite, and photocatalyst dosage on DCF removal and conversion efficiency by solar/TiO2-FeZ/H2O2 process was investigated. TiO2-FeZ demonstrated higher photocatalytic activity than pure TiO2 under solar irradiation in acidic conditions and presence of H2O2.

Properties and Application Perspective of Hybrid Titania-Silica Patterns Fabricated by Inkjet Printing.

A hybrid titania-silica cold-setting sol has been developed that can be deposited onto a wide variety of surfaces without the need for high-temperature fixing and that is suitable for material printing deposition. Thin hybrid titania-silica coatings were patterned onto glass and PET substrates by inkjet printing. Well-defined hybrid titania-silica patterns, with thicknesses ranging from 40 to 400 nm, were fabricated by overprinting 1 to 10 layers. Excellent mechanical, optical, and photocatalytic properties were observed, making the reported material well suited for the fabrication of transparent self-cleaning coatings both on mineral and organic substrates. The printed patterns exhibit photoelectrochemical activity that can be further improved by thermal or photonic curing. A concept of fully printed interdigitated photoelectrochemical cells on flexible PET substrates utilizing the reported hybrid photocatalyst is disclosed as well.

Highly active photocatalytic coatings prepared by a low-temperature method.

Photocatalytic properties of titanium (IV) oxide (TiO2) in anatase form can be used for various purposes, including photocatalytic purification of water. For such an application, suspended or fixed photocatalytic reactors are used. Those with fixed phase seem to be preferred due to some advantages, one of which is the avoidance of photocatalyst filtration. To avoid leaching and exfoliation of the fixed phase, an immobilization procedure leading to a good adhesion of a catalyst to a substrate is crucial. Within this work, we present physical and photocatalytic characterization results of five commercially available TiO2 photocatalysts (P25, P90, PC500, KRONOClean 7000, VPC-10) and one pigment (Hombitan LO-CR-S-M), which were successfully immobilized on glass slides by a "sol suspension" procedure. Different mechanical tests and characterization methods were used to evaluate the stability and morphology of the layers. Evaluation of photocatalytic activity was done by tests under UVA and UV-vis irradiation, using a method based on the detection of the fluorescent oxidation product of terephthalic acid (TPA), i.e., hydroxyterephthalic acid (HTPA). Aeroxide® P90 incorporated into the silica-titania binder was the most photocatalytically active layer and, unlike the others, showed significant increase of photocatalytic activity through the entire range of tested UVA irradiation intensities (2.3 mW/cm(2)-6.1 mW/cm(2)). The high mechanical stability of some photocatalytic layers allows using them in water photocatalytic purification reactions.

Photocatalytic degradation of gaseous toluene by using immobilized titania/silica on aluminum sheets.

PURPOSE: The aim of this study was to prepare a highly active immobilized titania/silica photocatalyst and to test its performance in situ toward degradation of toluene as one of the major toxic indoor contaminants. METHODS: In this work, two different titania layers immobilized on Al sheets were synthesized via low temperature sol-gel method employing presynthesized highly active titania powders (Degussa P25 and Millennium PC500, mass ratio 1:1): (a) with a silica/titania binder and a protective layer and (b) without the binder. The photocatalysts were characterized by X-ray diffraction, nitrogen sorption measurements, scanning electron microscopy (SEM), infrared spectroscopy, and UV-vis diffuse reflectance spectroscopy (DRS). The in situ photocatalytic degradation of gaseous toluene was selected as a probe reaction to test photocatalytic activity and to verify the potential application of these materials for air remediation. RESULTS: Results show that nontransparent highly photocatalytically active coatings based on the silica/titania binder and homogeneously dispersed TiO(2) powders were obtained on the Al sheets. The crystalline structure of titania was not altered upon addition of the binder, which also prevented inhomogeneous agglomeration of particles on the photocatalyst surface. The photoactivity results indicate that the adsorption properties and photocatalytic activity of immobilized photocatalysts with the silica/titania binder and an underlying protective layer were very effective and additionally, they exhibited considerably improved adhesion and uniformity. CONCLUSION: We present a new highly photocatalytically active immobilized catalyst on a convenient metallic support, which has a potential application in an air cleaning device.