Tear-Based Aqueous Batteries for Smart Contact Lenses Enabled by Prussian Blue Analogue Nanocomposites.

Batteries for contact lenses fabricated by conventional methods could cause severe damage to the eyes if broken. Herein, we present flexible aqueous batteries that operate in tears and provide a safe power supply to smart contact lenses. Nanocomposite flexible electrodes of carbon nanotubes and Prussian blue analogue nanoparticles for cathode and anode were embedded in UV-polymerized hydrogel as not only a soft contact lens but also an ion-permeable separator. The battery exhibited a discharging capacity of 155 µAh in an aqueous electrolyte of 0.15 M Na-ions and 0.02 M K-ions, equivalent to the ionic concentration of tears. The power supply was enough to operate a low-power static random-access memory. In addition, we verified the mechanical stability, biocompatibility and compatibility with a contact lens cleaning solution. It could ultimately enable a safe power supply for smart contact lenses without risk of injury due to the leakage or breakage of the battery.

Selective Ion Sweeping on Prussian Blue Analogue Nanoparticles and Activated Carbon for Electrochemical Kinetic Energy Harvesting.

Kinetic energy is an ideal energy source for powering wearable devices or internet of things (IoTs) because of its abundant availability. Currently, most kinetic energy harvesting systems are based on friction or deformation, which require high-frequency motion or high material durability for sustainable energy harvesting. Here, we introduce selective ion sweeping in a hybrid cell consisting of an ion-adsorbing activated carbon and an ion-hosting Prussian blue analogue nanoparticle for electrochemical kinetic energy harvesting. The flow of electrolyte induced by kinetic motion of the cell causes ion sweeping only on the surface of the supercapacitor and induces current flow between the supercapacitor and the battery electrode. This method exhibits 24.9 µW cm-2 as maximum power of system with 34 Ω load in half-cell test, which is several thousand times smaller than the load used in conventional methods. In a long-term test with full cell, this method supplies a continuous current flow ∼6 µA cm-2 at the flow of 40 mL min-1 for 500 cycles without performance decay. The prototype of the hybrid cell demonstrated kinetic energy harvesting from bare hand press with the various flow speeds from 0.41 to 1.39 cm s-1 as well as walking, running, and door closing, which are representative examples of low-frequency kinetic motions in daily life. We believe that the simple structure of the hybrid cell will enable power supply to various applications from miniaturized systems (e.g., IoTs and wearables) to large-scale systems (e.g., ocean wave energy harvesting).

Copper Hexacyanoferrate Thin Film Deposition and Its Application to a New Method for Diffusion Coefficient Measurement.

The use of Prussian blue analogues (PBA) materials in electrochemical energy storage and harvesting has gained much interest, necessitating the further clarification of their electrochemical characteristics. However, there is no well-defined technique for manufacturing PBA-based microelectrochemical devices because the PBA film deposition method has not been well studied. In this study, we developed the following deposition method for growing copper hexacyanoferrate (CuHCFe) thin film: copper thin film is immersed into a potassium hexacyanoferrate solution, following which the redox reaction induces the spontaneous deposition of CuHCFe thin film on the copper thin film. The film grown via this method showed compatibility with conventional photolithography processes, and the micropattern of the CuHCFe thin film was successfully defined by a lift-off process. A microelectrochemical device based on the CuHCFe thin film was fabricated via micropatterning, and the sodium ion diffusivity in CuHCFe was measured. The presented thin film deposition method can deposit PBAs on any surface, including insulating substrates, and it can extend the utilization of PBA thin films to various applications.

Efficient Low-Grade Heat Harvesting Enabled by Tuning the Hydration Entropy in an Electrochemical System.

Harvesting of low-grade heat (<100 °C) is promising, but its application is hampered by a lack of efficient and low-cost systems. The thermally regenerative electrochemical cycle (TREC) is a potential alternative system with high energy-conversion efficiency. Here, the temperature coefficient (α), which is a key factor in a TREC, is studied by tuning the hydration entropy of the electrochemical reaction. The change of α in copper hexacyanoferrate (CuHCFe) with intercalation of different monovalent cations (Na+ , K+ , Rb+ , and Cs+ ) and a larger α value of -1.004 mV K-1 being found in the Rb+ system are observed. With a view to practical application, a full cell is constructed for low-grade heat harvesting. The resultant ηe is 4.34% when TREC operates between 10 and 50 °C, which further reaches 6.21% when 50% heat recuperation is considered. This efficiency equals to 50% of the Carnot efficiency, which is thought to be the highest ηe reported for low-grade heat harvesting systems. This study provides a fundamental understanding of the mechanisms governing the TREC, and the demonstrated efficient system paves the way for low-grade heat harvesting.