Mechanical characteristics of metal nanoparticle thin film on flexible substrate exposed to saline solution.

The robust and reliable mechanical characteristics of metal nanoparticle (NP) thin films on flexible substrates are important because they operate under tensile, bending, and twisting loads. Furthermore, in wearable printed electronics applications, salty solutions such as sweat and seawater can affect the mechanical reliabilities of devices. In this paper, we investigated the effect of sodium chloride (NaCl) solutions on silver (Ag) NP thin films on flexible polymer substrate. After exposure to NaCl solution of Ag NP thin film, we observed the aggregation behavior between Ag NPs and formation of larger pores in the film due to the removal of organic capping layer from the surface of Ag NPs. The average porosity and 5% deviation strains of Ag NP thin films on the polyimide substrate were dramatically increased and decreased from 2.99% to 9.64% and from 3.94% to 0.87%, respectively, after exposure to NaCl solution for 1 h. Also, we verified a drastic deterioration of the surface adhesion of the Ag NP thin film to the substrate by exposure to NaCl solution. We could observe crack propagation and delamination by in-situ scanning electron microscope imaging. In addition, passivation effect by a parylene layer for preventing the permeation of the saline solution was investigated.

Bottom-up Cu filling of annular through silicon vias: Microstructure and texture.

Microstructural and morphological evolution during bottom-up Cu filling of annular through silicon vias (TSV) in a CuSO4-H2SO4-Cl--poloxamine electrolyte is examined. Deposition proceeds in two distinct stages beginning with a passive-to-active state transition on the via sidewalls whose depth and ultimate thickness depends on the polymer flux. Growth is conformal or tapered with columnar grains whose width and texture differ between the outer and inner sidewalls of the annulus due to area reduction and expansion respectively. The outer sidewall and bottom surface have a preferred texture; 〈111〉//ND (via normal) and 〈110〉//CD (via circumferential). With time the sidewalls passivate while further deposition is localized to the via bottom. Bottom-up growth then fills the TSV with the formation and selective expansion of the 〈110〉//ND textured grains. At higher suppressor concentrations the initial onset and transient period of sidewall deposition is displaced to greater depth and the subsequent shift to bottom-up filling with large 〈110〉//ND texture grains occurs earlier. The dominant 〈110〉//ND texture during bottom-up filling is congruent with Cl- stabilized texture development. The absence of suppression indicates that the polymeric suppressor does not adsorb on the active upward propagating surface.

Tensile characteristics of metal nanoparticle films on flexible polymer substrates for printed electronics applications.

Metal nanoparticle solutions are widely used for the fabrication of printed electronic devices. The mechanical properties of the solution-processed metal nanoparticle thin films are very important for the robust and reliable operation of printed electronic devices. In this paper, we report the tensile characteristics of silver nanoparticle (Ag NP) thin films on flexible polymer substrates by observing the microstructures and measuring the electrical resistance under tensile strain. The effects of the annealing temperatures and periods of Ag NP thin films on their failure strains are explained with a microstructural investigation. The maximum failure strain for Ag NP thin film was 6.6% after initial sintering at 150 °C for 30 min. Thermal annealing at higher temperatures for longer periods resulted in a reduction of the maximum failure strain, presumably due to higher porosity and larger pore size. We also found that solution-processed Ag NP thin films have lower failure strains than those of electron beam evaporated Ag thin films due to their highly porous film morphologies.

Direct micro/nano metal patterning based on two-step transfer printing of ionic metal nano-ink.

We present a direct metal patterning method by a two-step transfer printing process of non-particle, ionic metal nano-ink solution. This fabrication method allows a simple direct patterning of various micro/nanoscale metallic structures. Complex structures such as multilayer line arrays, patterns along non-flat topologies, and micro/nanoscale hybrid patterns can be achieved by using this process. Also, the low temperature and pressure process conditions are compatible with the fabrication of electronic structures and devices on flexible substrates such as polyimide film and photographic papers. As an application of this process, we fabricated ZnO nanowire-based flexible UV sensors, where metal electrodes were fabricated by two-step transfer printing. In the case of ZnO nanowire sensors, highly sensitive and fast responding performances to UV illumination and good mechanical robustness against repeated bending conditions could be verified.

Interfacial toughening of solution processed Ag nanoparticle thin films by organic residuals.

Reliable integration of solution processed nanoparticle thin films for next generation low-cost flexible electronics is limited by mechanical damage in the form of delamination and cracking of the films, which has not been investigated quantitatively or systematically. Here, we directly measured the interfacial fracture energy of silver nanoparticle thin films by using double cantilever beam fracture mechanics testing. It was demonstrated that the thermal annealing temperature and period affect the interfacial fracture energy. Also it was found that the interfacial fracture resistance can be maximized with optimized annealing conditions by the formation of organic residual bridges during the annealing process.

Study of lipid proton difference evaluation via 9.4T MRI analysis of fatty liver induced by exposure to methionine and choline-deficient (MCD) diet and high-fat diet (HFD) in an animal model.

The selection of an animal model is based on the pathological mechanism appropriate for experimental investigation because the therapeutic effect was low depending on the pathological occurrence mechanism. The purpose of this study is to elucidate the changes in lipid proton concentration in two animal models of nonalcoholic fatty liver disease (NAFLD): methionine and choline-deficient (MCD) diet and high-fat diet (HFD). We calculated the T2 relaxation time of 7 lipid protons (LP) in the 9.4 T MRS phantom experiment. The concentrations of LPs were adjusted for T2 and T2* of MCD, HFD, and CCl4 fatty liver animal models. Multivariate analysis and Pearson correlation were performed to analyze LP concentration, and the difference was investigated via Kendall correlation and independent t-test using LP composition ratio. The T2 relaxation time of each LP was accurately determined using phantom experiments. The in vivo magnetic resonance spectroscopy (MRS) data were obtained by quantifying the t2/t2* corrected LP concentration in the liver of the animal model. In case of MCD and HFD, there was an average difference in all LPs except 0.9 ppm LP, and the MCD and CCl4 groups showed differences in the average of all LPs. However, there was no difference between LP of HFD and CCl4 groups. A higher level of unsaturated fatty acids was found in the MCD fatty liver model than in HFD induced fatty liver.

Self-Regulation of Infrared Using a Liquid Crystal Mixture Doped with Push-Pull Azobenzene for Energy-Saving Smart Windows.

A self-regulating liquid crystal (LC) smart window whose reflectance changes with ambient conditions is demonstrated. Thermally or optically induced switching between the transparent state and a near-infrared (NIR) reflective state can be used for energy-saving windows. Reflection of NIR can reduce the energy used for cooling, while remaining transparent to visible light. By changing the initial alignment of LCs, the window can be switched between hazy-opaque and IR-reflective states to be used for privacy windows.

Electrochemical Generation of Mesopores and Residual Oxygen for the Enhanced Activity of Silver Electrocatalysts.

The development of stable and efficient electrocatalysts is of key importance for the establishment of a sustainable society. The activity of a metal electrocatalyst is determined by its electrochemically active surface area and intrinsic activity, which can be increased using highly porous structures and heteroatomic doping, respectively. Herein, we propose a general strategy of generating mesopores and residual oxygen in metal electrocatalysts by reduction of metastable metal oxides using Ag2O3 electrodeposited onto carbon paper as a model system and demonstrating that the obtained multipurpose porous Ag electrocatalyst has high activity for the electroreduction of O2 and CO2. The presence of mesopores and residual oxygen is confirmed by electrochemical and spectroscopic techniques, and quantum mechanical simulations prove the importance of residual oxygen for electrocatalytic activity enhancement. Thus, the adopted strategy is concluded to allow the synthesis of highly active metal catalysts with controlled mesoporosity and residual oxygen content.

A stretchable strain sensor based on a metal nanoparticle thin film for human motion detection.

Wearable strain sensors for human motion detection are being highlighted in various fields such as medical, entertainment and sports industry. In this paper, we propose a new type of stretchable strain sensor that can detect both tensile and compressive strains and can be fabricated by a very simple process. A silver nanoparticle (Ag NP) thin film patterned on the polydimethylsiloxane (PDMS) stamp by a single-step direct transfer process is used as the strain sensing material. The working principle is the change in the electrical resistance caused by the opening/closure of micro-cracks under mechanical deformation. The fabricated stretchable strain sensor shows highly sensitive and durable sensing performances in various tensile/compressive strains, long-term cyclic loading and relaxation tests. We demonstrate the applications of our stretchable strain sensors such as flexible pressure sensors and wearable human motion detection devices with high sensitivity, response speed and mechanical robustness.