In situ Functionalized Mesoporous Silicas for Sustainable Remediation Strategies in Removal of Inorganic Pollutants from Contaminated Environmental Water.

Low-cost mesoporous silicas of the SBA-15 family were prepared, aimed for removal of a broad spectrum of both cationic and anionic forms of hazardous metal pollutants (Cr(III, VI), Mn(II, VII), Pb(II), Cd(II), and Cu(II)) from environmental water. Series of mono- and bifunctional materials with immobilized ethylenediaminetriacetic acid (EDTA), primary amine (NH2), and quaternary ammonium (QAS) groups were prepared in a cost-efficient one-step synthesis using two silica sources, low-cost sodium metasilicate (Na2SiO3 9H2O) and the conventional source-tetraethylorthosilicate (TEOS). The functionalized SBA-15 samples obtained from both silica sources were highly ordered, as evidenced by TEM and SAXS data. All obtained materials were mesoporous with high surface area values of up to 745 m2/g, pore volumes from 0.99 to 1.44 cm3/g, and narrow pore distributions near 7 nm. The adsorption affinity of the EDTA-functionalized samples followed the common order Pb(II)> Cd(II)> Cu(II)> Cr(III)> Mn(II), which could be explained based on the Pearson theory. The highest adsorption capacities were observed for samples functionalized by EDTA groups using TEOS for synthesis (TEOS/EDTA): 195.6 mg/g for Pb(II), 111.2 mg/g for Cd(II), 58.7 mg/g for Cu(II), 57.7 mg/g for Cr(III), and 49.4 mg/g for Mn(II). Moreover, organic matter (humic acid up to 10 mg/L) and inorganic (Na(I), K(I), Mg(II), Ca(II), etc) macrocomponents present in environmental water had almost negligible effect on the removal of these cations. The NaSi/EDTA/NH2 sample revealed a better selectivity compared to the NaSi/NH2 sample towards such species as Cr(III), Mn(II), Cd(II), and Cu(II). The chromate-ions uptake at pH 7.5 by the TEOS/QAS sample turned practically unaffected by the presence of doubly charged anions (CO3 2-, SO4 2-). The content of functional groups on the surface of MS decreased only slightly (∼1-5%) after several regeneration cycles. The complete desorption of all heavy metal ions can be achieved using 1 mol/L EDTA solution. Reusability tests demonstrated the complete stability of the adsorbent for at least five to six consecutive adsorption/desorption cycles with no decrease in its adsorption characteristics compared to those obtained by 0.05 mol/L HNO3 treatments. The synthesized mesoporous materials were evaluated for removal of the heavy metal ions from drinking and different natural water samples, proving their potential as sustainable, effective, and cost-efficient adsorbents.

Steam Activation of Acid-Chars for Enhanced Textural Properties and Pharmaceuticals Removal.

The present work aims to explore steam activation of sisal or glucose-derived acid-chars as an alternative to KOH activation to prepare superactivated carbons, and to assess the adsorption performance of acid-chars and derived activated carbons for pharmaceuticals removal. Acid-chars were prepared from two biomass precursors (sisal and glucose) using various H2SO4 concentrations (13.5 M, 12 M, and 9 M) and further steam-activated at increasing burn-off degrees. Selected materials were tested for the removal of ibuprofen and iopamidol from aqueous solution (kinetic and equilibrium assays) in single-solute conditions. Activated carbons prepared from acid-char carbonized with 13.5 M and 12 M H2SO4 are mainly microporous solids composed of compact rough particles, yielding a maximum surface area and a total pore volume of 1987 m2 g-1 and 0.96 cm3 g-1, respectively. Solid state NMR reveals that steam activation increased the aromaticity degree and amount of C=O functionalities. Steam activation improved the acid-chars adsorption capacity for ibuprofen from 20-65 mg g-1 to higher than 280 mg g-1, leading to fast adsorption kinetics (15-20 min). The maximum adsorption capacities of selected activated samples for ibuprofen and iopamidol were 323 and 1111 mg g-1, respectively.