Adsorption of Polystyrene from Theta Condition on Cellulose and Silica Studied by Quartz Crystal Microbalance.

Adsorption of hydrophobic polymers from a nonpolar solvent medium is an underutilized tool for modification of surfaces, especially of soft matter. Adsorption of polystyrene (PS) from a theta solvent (50/50 vol % toluene/heptane) on ultrathin model films of cellulose was studied with a quartz crystal microbalance with dissipation monitoring (QCM-D), using three different PS grades with monodisperse molecular weights (Mws). Comparison of cellulose to silica as an adsorbent was presented. Adsorption on both surfaces was mainly irreversible under the studied conditions. Characteristically to polymer monolayer formation, the mass of the adsorbing polymer increased with its Mw. The initial step of the layer formation was similar on both surfaces, but silica showed a stronger tendency for the formation of a loosely bound overlayer upon molecular rearrangements as the adsorption process proceeded. Despite the slightly less extended layers formed on cellulose at increasing Mw values, the overall thickness of the adsorbing wet layers on both surfaces was of the similar order of magnitude as the radius of gyration of the adsorbate molecule. Decent degree of hydrophobization of cellulose could be reached with all studied PS grades when the time allowed for adsorption was sufficient. QCM-D, a method conventionally utilized for studying aqueous systems, turned out to be a suitable tool for studying the adsorption process of hydrophobic polymers on soft polymeric matter such as cellulose taking place in a nonpolar solvent environment.

Protein Adsorption and Its Effects on Electroanalytical Performance of Nanocellulose/Carbon Nanotube Composite Electrodes.

Protein fouling is a critical issue in the development of electrochemical sensors for medical applications, as it can significantly impact their sensitivity, stability, and reliability. Modifying planar electrodes with conductive nanomaterials that possess a high surface area, such as carbon nanotubes (CNTs), has been shown to significantly improve fouling resistance and sensitivity. However, the inherent hydrophobicity of CNTs and their poor dispersibility in solvents pose challenges in optimizing such electrode architectures for maximum sensitivity. Fortunately, nanocellulosic materials offer an efficient and sustainable approach to achieving effective functional and hybrid nanoscale architectures by enabling stable aqueous dispersions of carbon nanomaterials. Additionally, the inherent hygroscopicity and fouling-resistant nature of nanocellulosic materials can provide superior functionalities in such composites. In this study, we evaluate the fouling behavior of two nanocellulose (NC)/multiwalled carbon nanotube (MWCNT) composite electrode systems: one using sulfated cellulose nanofibers and another using sulfated cellulose nanocrystals. We compare these composites to commercial MWCNT electrodes without nanocellulose and analyze their behavior in physiologically relevant fouling environments of varying complexity using common outer- and inner-sphere redox probes. Additionally, we use quartz crystal microgravimetry with dissipation monitoring (QCM-D) to investigate the behavior of amorphous carbon surfaces and nanocellulosic materials in fouling environments. Our results demonstrate that the NC/MWCNT composite electrodes provide significant advantages for measurement reliability, sensitivity, and selectivity over only MWCNT-based electrodes, even in complex physiological monitoring environments such as human plasma.

Noncovalent Surface Modification of Cellulose Nanopapers by Adsorption of Polymers from Aprotic Solvents.

Basic adsorption of hydrophobic polymers from aprotic solvents was introduced as a platform technology to modify exclusively the surfaces of cellulose nanopapers. Dynamic vapor sorption demonstrated that the water vapor uptake ability of the nanopapers remained unperturbed, despite strong repellency to liquid water caused by the adsorbed hydrophobic polymer on the surface. This was enabled by the fact that the aprotic solvents used for adsorption did not swell the nanopaper unlike water that is generally applied as the adsorption medium in such systems. As case examples, the adsorptions of polystyrene (PS) and poly(trifluoroethylene) (PF3E) were followed by X-ray photoelectron spectroscopy and water contact angle measurements, backed up with morphological analysis by atomic force microscopy. The resulting nanopapers are useful in applications like moisture buffers where repellence to liquid water and ability for moisture sorption are desired qualities.

Adsorption of hydrophobically end-capped poly(ethylene glycol) on cellulose.

Adsorption of poly(ethylene glycol), hydrophobically end-capped with octadecenylsuccinic anhydride (OSA-PEG-OSA), on an ultrathin film of cellulose has been studied by quartz crystal microbalance with dissipation monitoring (QCM-D) and atomic force microscopy (AFM). Normally, PEG does not adsorb on cellulosic surfaces, but the use of the telechelic hydrophobic modification was found to promote adsorption. The influence of the conformation of the polymer in solution prior to adsorption and the subsequent properties of the adsorbed layer were investigated. The adsorption experiments were done at concentrations below and above the critical association concentration. The adsorption of OSA-PEG-OSA on cellulose was observed to occur in four distinct stages. Because of the amphiphilic nature of cellulose, further adsorption experiments were performed on hydrophobic (polystyrene) and hydrophilic (silica) model substrates to illuminate the contribution of hydrophobic and hydrophilic factors in the adsorption phenomenon. As expected, the kinetics and the mechanism of adsorption were strongly dependent on the chemical composition of the substrate.

Charged ultrafiltration membranes based on TEMPO-oxidized cellulose nanofibrils/poly(vinyl alcohol) antifouling coating.

This study reports the potential of TEMPO-oxidized cellulose nanofibrils (T-CNF)/poly(vinyl alcohol) (PVA) coatings to develop functionalized membranes in the ultrafiltration regime with outstanding antifouling performance and dimensional/pH stability. PVA acts as an anchoring phase interacting with the polyethersulfone (PES) substrate and stabilizing for the hygroscopic T-CNF via crosslinking. The T-CNF/PVA coated PES membranes showed a nano-textured surface, a change in the surface charge, and improved mechanical properties compared to the original PES substrate. A low reduction (4%) in permeance was observed for the coated membranes, attributable to the nanometric coating thickness, surface charge, and hydrophilic nature of the coated layer. The coated membranes exhibited charge specific adsorption driven by electrostatic interaction combined with rejection due to size exclusion (MWCO 530 kDa that correspond to a size of ∼35-40 nm). Furthermore, a significant reduction in organic fouling and biofouling was found for T-CNF/PVA coated membranes when exposed to BSA and E. coli. The results demonstrate the potential of simple modifications using nanocellulose to manipulate the pore structure and surface chemistry of commercially available membranes without compromising on permeability and mechanical stability.

Arrangements of cationic starch of varying hydrophobicity on hydrophilic and hydrophobic surfaces.

Arrangements of cationic starches hydrophobized by acetylation (CS-acet) deposited from aqueous electrolyte solutions onto hydrophilized and hydrophobized silica surfaces were investigated by atomic force microscopy (AFM), X-ray photoelectron spectroscopy (XPS), and contact angle measurements. The influence of electrolyte composition, acetylation degree of cationic starch (DS(ACET)), and deposition method was examined. On a hydrophobic substrate, CS-acet formed an open film with structure strongly dependent on DS(ACET) and electrolyte composition of the solution. On a hydrophilic substrate, acetylation increased the hydrophobicity of the film when the starch was deposited by adsorbing. When deposition was made by spin coating, i.e., the CS-acet was forced onto the substrate, the hydrophobic tuning by acetylation was lost. The films deposited by spin coating were thicker and considerably rougher than those deposited by adsorbing.

Adsorption of cationic starch on cellulose studied by QCM-D.

The adsorption of cationic starch (CS) from aqueous electrolyte solutions onto model cellulose film has been investigated by the quartz crystal microbalance with dissipation monitoring (QCM-D) and X-ray photoelectron spectroscopy (XPS). The influence of the electrolyte composition and charge density of CS was examined. The adsorption of CS onto cellulose followed the general trends expected for polyelectrolyte adsorption on oppositely charged surfaces, with some exceptions. Thus, as result of the very low surface charge density of the cellulose surface, highly charged CS did not adsorb in a flat conformation even at low ionic strength. The porosity of the film, however, enabled the penetration of coiled CS molecules into the film at high electrolyte concentrations. Differences between the adsorption behavior of CS on cellulose and earlier observations of the adsorption of the same starches on silica could be explained by the different morphologies and acidities of the hydroxyl groups on the two surfaces.

Cellulose nanocrystal submonolayers by spin coating.

Dilute concentrations of cellulose nanocrystal solutions were spin coated onto different substrates to investigate the effect of the substrate on the nanocrystal submonolayers. Three substrates were probed: silica, titania, and amorphous cellulose. According to atomic force microscopy (AFM) images, anionic cellulose nanocrystals formed small aggregates on the anionic silica substrate, whereas a uniform two-dimensional distribution of nanocrystals was achieved on the cationic titania substrate. The uniform distribution of cellulose nanocrystal submonolayers on titania is an important factor when dimensional analysis of the nanocrystals is desired. Furthermore, the amount of nanocrystals deposited on titania was multifold in comparison to the amounts on silica, as revealed by AFM image analysis and X-ray photoelectron spectroscopy. Amorphous cellulose, the third substrate, resulted in a somewhat homogeneous distribution of the nanocrystal submonolayers, but the amounts were as low as those on the silica substrate. These differences in the cellulose nanocrystal deposition were attributed to electrostatic effects: anionic cellulose nanocrystals are adsorbed on cationic titania in addition to the normal spin coating deposition. The anionic silica surface, on the other hand, causes aggregation of the weakly anionic cellulose nanocrystals which are forced on the repulsive substrate by spin coating. The electrostatically driven adsorption also influences the film thickness of continuous ultrathin films of cellulose nanocrystals. The thicker films of charged nanocrystals on a substrate of opposite charge means that the film thickness is not independent of the substrate when spin coating cellulose nanocrystals in the ultrathin regime (<100 nm).