Poly(vinyl chloride)/Nanocarbon Composites for Advanced Potentiometric Membrane Sensor Design.

Polymer nanocomposites filled with carbon nanoparticles (CNPs) are a hot topic in materials science. This article discusses the current research on the use of these materials as interfacial electron transfer films for solid contact potentiometric membrane sensors (SC-PMSs). The results of a comparative study of plasticized poly (vinyl chloride) (pPVC) matrices modified with single-walled carbon nanotubes (SWCNTs), fullerenes-C60, and their hybrid ensemble (SWCNTs-C60) are reported. The morphological characteristics and electrical conductivity of the prepared nanostructured composite films are reported. It was found that the specific electrical conductivity of the pPVC/SWCNTs-C60 polymer film was higher than that of pPVC filled with individual nanocomponents. The effectiveness of this composite material as an electron transfer film in a new potentiometric membrane sensor for detecting phenylpyruvic acid (in anionic form) was demonstrated. Screening for this metabolic product of phenylalanine in body fluids is of significant diagnostic interest in phenylketonuria (dementia), viral hepatitis, and alcoholism. The developed sensor showed a stable and fast Nernstian response for phenylpyruvate ions in aqueous solutions over the wide linear concentration range of 5 × 10-7-1 × 10-3 M, with a detection limit of 10-7.2 M.

Oxidation of Ceramic Materials Based on HfB2-SiC under the Influence of Supersonic CO2 Jets and Additional Laser Heating.

The features of oxidation of ultra-high-temperature ceramic material HfB2-30 vol.%SiC modified with 1 vol.% graphene as a result of supersonic flow of dissociated CO2 (generated with the use of high-frequency induction plasmatron), as well as under the influence of combined heating by high-speed CO2 jets and ytterbium laser radiation, were studied for the first time. It was found that the addition of laser radiation leads to local heating of the central region from ~1750 to ~2000-2200 °C; the observed temperature difference between the central region and the periphery of ~300-550 °C did not lead to cracking and destruction of the sample. Oxidized surfaces and cross sections of HfB2-SiC-CG ceramics with and without laser heating were investigated using X-ray phase analysis, Raman spectroscopy and scanning electron microscopy with local elemental analysis. During oxidation by supersonic flow of dissociated CO2, a multilayer near-surface region similar to that formed under the influence of high-speed dissociated air flows was formed. An increase in surface temperature with the addition of laser heating from 1750-1790 to 2000-2200 °C (short term, within 2 min) led to a two to threefold increase in the thickness of the degraded near-surface area of ceramics from 165 to 380 microns. The experimental results indicate promising applications of ceramic materials based on HfB2-SiC as part of high-speed flying vehicles in planetary atmospheres predominantly composed of CO2 (e.g., Venus and Mars).

Hydrothermal Synthesis of Nickel Oxide and Its Application in the Additive Manufacturing of Planar Nanostructures.

The hydrothermal synthesis of nickel oxide in the presence of triethanolamine was studied. Furthermore, the relationship between the synthesis conditions, thermal behavior, crystal structure features, phase composition and microstructure of semi-products, and the target oxide nanopowders was established. The thermal behavior of the semi-products was studied using a simultaneous thermal analysis (in particular, using one that involved thermogravimetric analysis and differential scanning calorimetry, TGA/DSC). An X-ray diffraction (XRD) analysis revealed that varying the triethanolamine and nickel chloride concentration in the reaction system can govern the formation of α- and ß-Ni(OH)2-based semi-products that contain Ni(HCO3)2 or Ni2(CO3)(OH)2 as additional components. The set of functional groups in the powders was determined using a Fourier-transform infrared (FTIR) spectroscopy analysis. Using microextrusion printing, a composite NiO-(CeO2)0.80(Sm2O3)0.20 anode film was fabricated. Using XRD, scanning electron microscopy (SEM), and atomic force microscopy (AFM) analyses, it was demonstrated that the crystal structure, dispersity, and microstructure character of the obtained material correspond to the initial nanopowders. Using Kelvin probe force microscopy (KPFM) and scanning capacitance microscopy (SCM), the local electrophysical properties of the printed composite film were examined. The value of its conductivity was evaluated using the four-probe method on a direct current in the temperature range of 300-650 °C. The activation energy for the 500-650 °C region, which is of most interest in the context of intermediate-temperature SOFCs working temperatures, has been estimated.

A New Approach to the Synthesis of Nanocrystalline Cobalt Boride in the Course of the Thermal Decomposition of Cobalt Complexes [Co(DMF)6]2+ with Boron Cluster Anions.

In the course of the study, nanocrystalline cobalt monoboride was prepared by thermal decomposition of precursors [Co(DMF)6][An], where [An] = [B12H12]2- (1), [trans-B20H18]2- (2) or [B10Cl10]2- (3) in an argon atmosphere. Three new salt-like compounds 1-3 were prepared when Co(NO3)2 was allowed to react with (Et3NH)2[An]. Compound 1 is new; the structures of compounds 2 and 3 have been previously reported. Samples 1-3 were annealed at 900 °C in argon to form samples 1a-3a, which were characterized by single crystal XRD for 1 and powder XRD for 1-3. Powder XRD on the products showed the formation of BN and CoB for 1a in a 1:1 ratio; 2a gave a higher CoB:BN ratio but an overall decreased crystallinity. For 3a, only CoB was found. IR spectra of samples 1a-3a as well as X-ray spectral fluorescence analysis for 3a confirmed these results. The nanoparticular character of the decomposition products 1a-3a was shown using TEM; quite small particle sizes of about 10-15 nm and a quite normal size distribution were found for 1a and 2a, while the decomposition of 3 gave large particles with 200-350 nm and a broad distribution.

Synthesis of Disubstituted Carboxonium Derivatives of Closo-Decaborate Anion [2,6-B10H8O2CC6H5]-: Theoretical and Experimental Study.

A comprehensive study focused on the preparation of disubstituted carboxonium derivatives of closo-decaborate anion [2,6-B10H8O2CC6H5]- was carried out. The proposed synthesis of the target product was based on the interaction between the anion [B10H11]- and benzoic acid C6H5COOH. It was shown that the formation of this product proceeds stepwise through the formation of a mono-substituted product [B10H9OC(OH)C6H5]-. In addition, an alternative one-step approach for obtaining the target derivative is postulated. The structure of tetrabutylammonium salts of carboxonium derivative ((C4H9)4N)[2,6-B10H8O2CC6H5] was established with the help of X-ray structure analysis. The reaction pathway for the formation of [2,6-B10H8O2CC6H5]- was investigated with the help of density functional theory (DFT) calculations. This process has an electrophile induced nucleophilic substitution (EINS) mechanism, and intermediate anionic species play a key role. Such intermediates have a structure in which one boron atom coordinates two hydrogen atoms. The regioselectivity for the process of formation for the 2,6-isomer was also proved by theoretical calculations. Generally, in the experimental part, the simple and available approach for producing disubstituted carboxonium derivative was introduced, and the mechanism of this process was investigated with the help of theoretical calculations. The proposed approach can be applicable for the preparation of a wide range of disubstituted derivatives of closo-borate anions.

Synthesis and Structures of Lead(II) Complexes with Substituted Derivatives of the Closo-Decaborate Anion with a Pendant N3 Group.

In this work, we studied lead(II) and cobalt(II) complexation of derivatives [2-B10H9O(CH2)2O(CH2)2N3]2- and [2-B10H9O(CH2)5N3]2- of the closo-decaborate anion containing pendant azido groups in the presence of 1,10-phenanthroline and 2,2'-bipyridyl. Mononuclear [PbL2{An}] and binuclear [Pb2L4(NO3)2{An}] lead complexes (where {An} is the N3-substituted boron cluster) were isolated and studied by IR spectroscopy and elemental analysis. The mononuclear lead(II) complex [Pb(phen)2[B10H9O(CH2)2O(CH2)2N3] and the binuclear lead(II) complex [Pb2(phen)4(NO3)2[B10H9O(CH2)5)N3] were determined by single-crystal X-ray diffraction. In complex [Pb2(phen)4(NO3)2[B10H9O(CH2)5)N3], the boron cluster is coordinated by the metal atom only via the 3c2e MHB bonds. In complex [Pb(phen)2[B10H9O(CH2)2O(CH2)2N3], the coordination environment of the metal includes BH groups of the boron cluster and the oxygen atom of the exo-polyhedral substituent. When the reaction was performed in a CH3CN/water mixture, the binuclear lead(II) complex [(Pb(bipy)NO3)(Pb(bipy)2NO3)(B10H9O(CH2)2O(CH2)2N3)]·CH3CN·H2O was isolated, where the boron cluster acts as a bridging ligand between lead atoms coordinated by the boron cage via the O atoms of the substituent and/or the BH groups. In the course of cobalt(II) complexation, the starting compound (Ph4P)2[B10H9O(CH2)5N3] was isolated and its structure was also determined by X-ray diffraction. Although a number of lead(II) complexes with coordinated N3 are known from the literature, no complexes with the boron cluster coordinated by the pendant N3 group involved in the metal coordination have been isolated.

New type of RNA virus replication inhibitor based on decahydro-closo-decaborate anion containing amino acid ester pendant group.

In this work, a synthetic approach to prepare an example of new class of the derivatives of the closo-decaborate anion with amino acids detached from the boron cluster by pendant group has been proposed and implemented. Compound Na2[B10H9-O(CH2)4C(O)-His-OMe] was isolated and characterized. This compound has an inorganic hydrophobic core which is the 10-vertex boron cage and the -O(CH2)4C(O)-His-OMe organic substituent. It has been shown to possess strong antiviral activity in vitro against modern strains of A/H1N1 virus at 10 and 5 µg/mL. The compound has been found to be non-cytotoxic up to 160 µg/mL. At the same time, the compound has been found to be inactive against SARS-CoV-2, indicating specific activity against RNA virus replication. Molecular docking of the target derivative of the closo-decaborate anion with a model of the transmembrane region of the M2 protein has been performed and the mechanism of its antiviral action is discussed.

Atmospheric Pressure Solvothermal Synthesis of Nanoscale SnO2 and Its Application in Microextrusion Printing of a Thick-Film Chemosensor Material for Effective Ethanol Detection.

The atmospheric pressure solvothermal (APS) synthesis of nanocrystalline SnO2 (average size of coherent scattering regions (CSR)-7.5 ± 0.6 nm) using tin acetylacetonate as a precursor was studied. The resulting nanopowder was used as a functional ink component in microextrusion printing of a tin dioxide thick film on the surface of a Pt/Al2O3/Pt chip. Synchronous thermal analysis shows that the resulting semiproduct is transformed completely into tin dioxide nanopowder at 400 °C within 1 h. The SnO2 powder and the resulting film were shown to have a cassiterite-type structure according to X-ray diffraction analysis, and IR spectroscopy was used to establish the set of functional groups in the material composition. The microstructural features of the tin dioxide powder were analyzed using scanning (SEM) and transmission (TEM) electron microscopy: the average size of the oxide powder particles was 8.2 ± 0.7 nm. Various atomic force microscopy (AFM) techniques were employed to investigate the topography of the oxide film and to build maps of surface capacitance and potential distribution. The temperature dependence of the electrical conductivity of the printed SnO2 film was studied using impedance spectroscopy. The chemosensory properties of the formed material when detecting H2, CO, NH3, C6H6, C3H6O and C2H5OH, including at varying humidity, were also examined. It was demonstrated that the obtained SnO2 film has an increased sensitivity (the sensory response value was 1.4-63.5) and selectivity for detection of 4-100 ppm C2H5OH at an operating temperature of 200 °C.

Printing Technologies as an Emerging Approach in Gas Sensors: Survey of Literature.

Herein, we review printing technologies which are commonly approbated at recent time in the course of fabricating gas sensors and multisensor arrays, mainly of chemiresistive type. The most important characteristics of the receptor materials, which need to be addressed in order to achieve a high efficiency of chemisensor devices, are considered. The printing technologies are comparatively analyzed with regard to, (i) the rheological properties of the employed inks representing both reagent solutions or organometallic precursors and disperse systems, (ii) the printing speed and resolution, and (iii) the thickness of the formed coatings to highlight benefits and drawbacks of the methods. Particular attention is given to protocols suitable for manufacturing single miniature devices with unique characteristics under a large-scale production of gas sensors where the receptor materials could be rather quickly tuned to modify their geometry and morphology. We address the most convenient approaches to the rapid printing single-crystal multisensor arrays at lab-on-chip paradigm with sufficiently high resolution, employing receptor layers with various chemical composition which could replace in nearest future the single-sensor units for advancing a selectivity.

Non-Covalent Interactions in the Crystal Structures of Perbrominated Sulfonium Derivatives of the closo-Decaborate Anion.

A new series of compounds based on perbrominated disubstituted sulfonium derivatives of the closo-decaborate anion (n-Bu4N)[2-B10Br9SR2] (R = n-Pr, i-Pr, n-Bu, n-C8H17, n-C12H25, n-C18H37) was obtained, characterised by modern physicochemical methods of analysis. According to the results of an X-ray diffraction study, some of the anions and solvate molecules were disordered. The cations (n-Bu4N)+ and anions [2-B10Br9SR2]- were associated via C-H…Br and H…H contacts. In addition, Br…Br interactions between anions were revealed. The role of these contacts was analysed in terms of Hirshfeld surface analysis, QTAIM theory and the NCI method using quantum chemical calculations. An increase in the size of the alkyl R moiety led to significant strengthening of the total energy of H…H interactions. In the case of R = -n-C18H37, a parallel mutual orientation of alkyl moieties was established that was similar to the packing of salts of fatty acids. The nature of C-H…Br and Br…Br interionic interactions was found to be attractive, in contrast to the repulsive nature of intermolecular Br…Br interactions.

Protonation of Borylated Carboxonium Derivative [2,6-B10H8O2CCH3]-: Theoretical and Experimental Investigation.

The process of protonation of [2,6-B10H8O2CCH3]- was investigated both theoretically and experimentally. The most suitable conditions for protonation of the derivative [2,6-B10H8O2CCH3]- were found. The process of protonation was carried out in the presence of an excess of trifluoromethanesulfonic acid CF3SO3H at room temperature in dichloromethane solution. The structure of the resulting complex [2,6-B10H8O2CCH3*Hfac]0 was established using NMR data and the results of DFT calculations. An additional proton atom Hfac was found to be localized on one of the facets that was opposite the boron atom in a substituted position, and which bonded mainly with one apical boron atom. The main descriptors of the B-Hfac bond were established theoretically using QTAIM and NBO approaches. In addition, the mechanism of [2,6-B10H8O2CCH3]- protonation was investigated.

High-Temperature Spin Crossover in Iron(II) Complexes with 2,6-Bis(1H-imidazol-2-yl)pyridine.

Novel iron(II) coordination compounds containing a ligand 2,6-bis(1H-imidazol-2-yl)pyridine (L), having such a composition as [FeL2]SO4·0.5H2O, [FeL2]Br2·H2O, [FeL2](ReO4)2, [FeL2]B10H10∙H2O, [FeL2]B12H12∙1.5H2O had been synthesized and studied using UV-Vis (diffuse reflectance), infrared, extended X-ray absorption fine structure (EXAFS), and Mössbauer spectroscopy methods, as well as X-ray diffraction and static magnetic susceptibility methods. The analysis of the µeff(T) dependence in the temperature range of 80-600 K have shown that all the obtained complexes exhibit a high-temperature spin crossover 1A1 ↔ 5T2.

Synthesis of Perchlorinated Sulfonium Derivatives of closo-Decaborate Anion [2-B10Cl9SR2]- (R = i-C3H7, n-C3H7, n-C4H9, n-C8H17, n-C12H25, n-C18H37, CH2Ph, and cyclo-S(CH2)4).

A method for obtaining perchlorinated di-S,S-substituted derivatives of the closo-decaborate anion with various alkyl groups has been developed: [B10Cl9SR2]- (R= i-C3H7, n-C3H7, n-C4H9, n-C8H17, n-C12H25, n-C18H37, CH2Ph, and cyclo-S(CH2)4). The method is based on the preparation of the sulfonium-substituted anion [B10H9SR2]- by alkylation of the anion [B10H9SH]2- with bromoalkanes (i-C3H7Br, n-C3H7Br, n-C4H9Br, n-C8H17Br, n-C12H25Br, n-C18H37Br, PhCH2Br, and BrCH2(CH2)2CH2Br) followed by the cluster chlorination with sulfuryl chloride SO2Cl2 in acetonitrile. The process proceeds until the hydrogen atoms in the boron cluster are completely replaced with chlorine and completes within 60 h. It has been found that the melting point of salts ((C4H9)4N)[B10Cl9SR2] (R= i-C3H7, n-C3H7, n-C4H9, n-C8H17, n-C12H25, and n-C18H37) strongly depends on the length of the hydrocarbon chain of the substituent R.

Primary Amine Nucleophilic Addition to Nitrilium Closo-Dodecaborate [B12H11NCCH3]-: A Simple and Effective Route to the New BNCT Drug Design.

In the present work, a convenient and straightforward approach to the preparation of borylated amidines based on the closo-dodecaborate anion [B12H11NCCH3NHR]-, R=H, Alk, Ar was developed. This method has two stages. A nitrile derivative of the general form [B12H11NCCH3]- was obtained, using a modified technique, in the first stage. On the second stage the resulting molecular system interacted with primary amines to form the target amidine products. This approach is characterised by a simple chemical apparatus, mild conditions and high yields of the final products. The mechanism of the addition of amine to the nitrile derivative of the closo-dodecaborate anion was studied, using quantum-chemical methods. The interaction between NH3 and [B12H11NCCH3]- ammonia was chosen as an example. It was found that the structure of the transition state determines the stereo-selectivity of the process. A study of the biological properties of borylated amidine sodium salts indicated that the substances had low toxicity and could accumulate in cancer cells in significant amounts.

Fused 1,2-Diboraoxazoles Based on closo-Decaborate Anion-Novel Members of Diboroheterocycle Class.

The novel members of the 1,2-diboraoxazoles family have been obtained. In the present work, we have carried out the intramolecular ring-closure reaction of borylated iminols of general type [B10H9N=C(OH)R]- (R = Me, Et, nPr, iPr, tBu, Ph, 4-Cl-Ph). This process is conducted in mild conditions with 83-87% yields. The solid-state structures of two salts of 1,2-diboraoxazoles were additionally investigated by X-ray crystallography. In addition, the phenomena of bonding interactions in the 1,2-diboraoxazole cycles have been theoretically studied by the Quantum Theory of Atoms in Molecules analysis. Several local and integral topological properties of the electron density involved in these interactions have been computed.

Solvent-Induced Encapsulation of Cobalt(II) Ion by a Boron-Capped tris-Pyrazoloximate.

Boron-cross-linked cobalt(II) pseudoclathrochelate was obtained by the template reaction of 2-acetylpyrazoloxime, phenylboronic acid, and a new DMF cobalt(II) solvato complex with a decachloro-closo-decaborate dianion. As confirmed by single-crystal X-ray diffraction, this complex crystallizes with two symmetry-independent cobalt(II) pseudoclathrochelate cations, one decachloro-closo-decaborate dianion, one benzene, one dichloromethane solvent molecule, and two molecules of DMF. The latter act as pseudocapping fragments to the monocapped tris-pyrazoloximate ligands by forming N-H···O hydrogen bonds with their pyrazole groups. The CoIIN6-coordination polyhedra adopt a nearly ideal TP geometry with distortion angles φ equal to 1.22(16) and 2.58(17)° for two symmetry-independent pseudoclathrochelate cations, both containing the encapsulated cobalt(II) ion in its high-spin state (Co-N 2.115(4)-2.198(3) Å). Magnetic properties of this complex were studied both by dc-magnetometry and by solution-state NMR spectroscopy to reveal a high magnetic anisotropy, thus suggesting a large magnetic susceptibility tensor anisotropy (25.8 × 10-32 m3 at 298 K) and a large negative zero-field splitting energy (-85 cm-1). The results of magnetometry studies in the ac magnetic field suggest a single molecule magnet behavior of this TP complex with an effective magnetization reversal barrier of approximately 130 cm-1. Its pseudocapping DMF molecules that form H-bonds with tris-pyrazoloximate fragments are easy to substitute by strong H-bond acceptors, such as chloride ions and di- and tetramethylureas, thus affecting the magnetic properties of a whole pseudomacrobicyclic paramagnetic system.

Existence of homoclinic orbits and heteroclinic cycle in a class of three-dimensional piecewise linear systems with three switching manifolds.

In this article, we construct a kind of three-dimensional piecewise linear (PWL) system with three switching manifolds and obtain four theorems with regard to the existence of a homoclinic orbit and a heteroclinic cycle in this class of PWL system. The first theorem studies the existence of a heteroclinic cycle connecting two saddle-foci. The existence of a homoclinic orbit connecting one saddle-focus is investigated in the second theorem, and the third theorem examines the existence of a homoclinic orbit connecting another saddle-focus. The last one proves the coexistence of the heteroclinic cycle and two homoclinic orbits for the same parameters. Numerical simulations are given as examples and the results are consistent with the predictions of theorems.

Approximating hidden chaotic attractors via parameter switching.

In this paper, the problem of approximating hidden chaotic attractors of a general class of nonlinear systems is investigated. The parameter switching (PS) algorithm is utilized, which switches the control parameter within a given set of values with the initial value problem numerically solved. The PS-generated attractor approximates the attractor obtained by averaging the control parameter with the switched values, which represents the hidden chaotic attractor. The hidden chaotic attractors of a generalized Lorenz system and the Rabinovich-Fabrikant system are simulated for illustration.

Solid-State Reactions of Eicosaborate [B20 H18 ]2- Salts and Complexes.

A series of salts and complexes containing trans- and iso-isomers of octadecahydro-eicosaborate [B20 H18 ]2- dianion is synthesized and characterized using FTIR and 11 B NMR spectroscopies and X-ray diffraction techniques. Both isomers are found to act as four-, bi-, or zero-dentate ligands in reactions with copper(II), silver(I), and lead(II) through apical and/or equatorial boron atoms. Solid-state photo- and thermoinitiated reactions of octadecahydro-eicosaborate isomerization and solvent cleavage occurring in these compounds in a single-crystal-to-single-crystal manner are studied in situ. In contrast with solutions, in solids the reaction of boron cluster transformation occurs rarely, thus, analysis of crystal packing allowed us to suggest some criteria of isomerization of macropolyhedral boranes in crystals. X-ray diffraction data are used to confirm reaction path of isomerization of the [B20 H18 ]2- dianion.

closo-Dodecaborate Intercalated Yttrium Hydroxide as a First Example of Boron Cluster Anion-Containing Layered Inorganic Substances.

The first member, Y2(OH)5.46(B12H12)0.23Cl0.08·4.98H2O, of a new family of boron-containing substances, closo-dodecaborate intercalated layered rare-earth hydroxides, was synthesized using a microwave-assisted hydrothermal method. The structure and composition of this compound were studied by X-ray diffraction, transmission and scanning electron microscopy, thermal analysis, inductively coupled plasma mass spectrometry, IR spectroscopy, and X-ray photoelectron spectroscopy. The title compound had the composition Y2(OH)5.46(B12H12)0.23Cl0.08·4.98H2O and crystallized in a form of plate-like, aggregated particles less than 10 nm thick. The coordination of closo-dodecaborate anions with yttrium hydroxide host layers was demonstrated.