HSF-1 regulators DDL-1/2 link insulin-like signaling to heat-shock responses and modulation of longevity.

Extended longevity is often correlated with increased resistance against various stressors. Insulin/IGF-1-like signaling (IIS) is known to have a conserved role in aging and cellular mechanisms against stress. In C. elegans, genetic studies suggest that heat-shock transcription factor HSF-1 is required for IIS to modulate longevity. Here, we report that the activity of HSF-1 is regulated by IIS. This regulation occurs at an early step of HSF-1 activation via two HSF-1 regulators, DDL-1 and DDL-2. Inhibition of DDL-1/2 increases longevity and thermotolerance in an hsf-1-dependent manner. Furthermore, biochemical analyses suggest that DDL-1/2 negatively regulate HSF-1 activity by forming a protein complex with HSF-1. The formation of this complex (DHIC) is affected by the phosphorylation status of DDL-1. Both the formation of DHIC and the phosphorylation of DDL-1 are controlled by IIS. Our findings point to DDL-1/2 as a link between IIS and the HSF-1 pathway.

Interactive tissue reactions of 1064-nm focused picosecond-domain laser and dermal cohesive polydensified matrix hyaluronic acid treatment in in vivo rat skin.

BACKGROUND: Picosecond-domain laser treatment using a microlens array (MLA) or a diffractive optical element (DOE) generates micro-injury zones in the epidermis and upper dermis. OBJECTIVE: To investigate interactive tissue reactions between MLA-type picosecond laser pulses and cohesive polydensified matrix hyaluronic acid (CPMHA) filler in the dermis. METHODS: In vivo rats with or without CPMHA pretreatment were treated with a 1064-nm picosecond-domain neodymium:yttrium-aluminum-garnet (Nd:YAG) laser using an MLA or DOE. Skin samples were obtained at post-treatment days 1, 10, and 21 and histologically and immunohistochemically analyzed. RESULTS: Picosecond-domain Nd:YAG laser treatment with an MLA-type or a DOE-type handpiece generated fractionated zones of pseudo-cystic cavitation along the lower epidermis and/or upper papillary dermis at Day 1. At Day 21, epidermal thickness, dermal fibroblasts, and collagen fibers had increased. Compared to CPMHA-untreated rats, rats pretreated with CPMHA showed marked increases in fibroblasts and collagen fibers in the papillary dermis. Immunohistochemical staining for the hyaluronic acid receptor CD44 revealed that MLA-type picosecond laser treatment upregulated CD44 expression in the basilar epidermis and dermal fibroblasts. CONCLUSIONS: We suggest that the hyaluronic acid-rich environment associated with CPMHA treatment may enhance MLA-type picosecond-domain laser-induced tissue reactions in the epidermis and upper dermis.

Low Temperature Co-Fired Ceramic-Based and Heater-Embedded Toxic Gas Sensors with Nanostructured SnO2 Thick Films.

In this study, we designed, prepared, and characterized Low Temperature Co-fired Ceramic (LTCC) toxic gas sensor devices with nanostructured SnO2 semiconducting thick films. In order to promote the reaction of carbon monoxide (CO) toxic gas molecules on the SnO2 thick films, a RuO2 planar heater was inserted into the LTCC substrate. Using an optimized RuO2 heater, the surface temperature of the LTCC substrate reached 360 °C within 25 seconds at an applied voltage of 5 V. The power consumption for the surface of the LTCC substrate to reach 300 °C was 778 mW. A nanostructured SnO2 thick film as a gas sensing layer was prepared by the ink dropping method on Pt electrodes patterned on the LTCC substrate. The gas sensor device was packaged in a commercial housing to measure the CO gas response. The fabricated gas sensor showed a gas response (Rair/Rgas) of 5.26 at a CO gas concentration of 500 ppm and a temperature of 300 °C. Additionally, a mild plasma post-treatment using Ar discharge gas improved the gas response up to 6.35 at the equivalent measurement conditions.

Pattern analysis of 532- and 1064-nm microlens array-type, picosecond-domain laser-induced tissue reactions in ex vivo human skin.

Optical pulses from picosecond lasers can be delivered to the skin using microlens array (MLA) optics or a diffractive beam splitter to generate multiple, focused, high-intensity, micro-injury zones in the epidermis and dermis. The aim of our study was to histopathologically and immunohistochemically evaluate the patterns of 532- and 1064-nm MLA-type, picosecond laser-induced tissue reactions in human skin immediately after treatment. Picosecond neodymium:yttrium-aluminum-garnet (Nd:YAG) laser treatment using an MLA-type beam at the wavelengths of 532 nm and 1064 nm was delivered ex vivo to human skin. Irradiated skin specimens were then microscopically analyzed after hematoxylin and eosin staining and CD31 and Melan-A immunostaining. A single pulse of 532-nm MLA-type, picosecond laser treatment elicited cystic cavitation lesions at sizes of 83.4 ± 16.5 µm × 70.2 ± 17.3 µm (31-mm distance step) and 91.0 ± 44.7 µm × 81.2 ± 36.3 µm (48-mm distance step) in the epidermis and papillary dermis. Meanwhile, a single pulse of 1064-nm laser treatment generated cystic cavitation lesions at sizes of 107.0 ± 18.1 µm × 83.3 ± 37.4 µm (single-pulse mode) and 100.8 ± 40.4 µm × 83.1 ± 29.4 µm (dual-pulse mode) throughout the lower epidermis and upper papillary dermis. Lining epithelial cells in cystic cavitation lesions in the epidermis showed Melan-A-positive immunoreactivity, while cystic cavitation lesions in the dermis exhibited CD31-positive or CD31-negative/Melan-A-negative immunoreactivity. The present data can be used to predict 532- and 1064-nm MLA-type, picosecond-domain laser-induced tissue reactions in human skin.

Ganglioside inhibition of CD8+ T cell cytotoxicity: interference with lytic granule trafficking and exocytosis.

Granule exocytosis-mediated cytotoxicity by CD8(+) CTL plays a crucial role in adaptive immunity to tumors and to intracellular pathogens. This T cell effector function has been shown to be defective in various murine tumor models and in human cancer. However, factors and their mechanisms that cause inhibition of CD8(+) T cell lytic function in tumor-bearing hosts remain to be fully defined. We postulate that gangliosides, highly expressed on tumor cell membranes, actively shed into the tumor microenvironment, and having well-established immunosuppressive properties, may be such a factor. We exposed primary mouse CD8(+) CTL to gangliosides derived from three sources (tumors and normal brain). This significantly inhibited cytotoxicity-mediated by granule exocytosis, that is, cytotoxicity of alloantigen-specific and polyclonal CD8(+) CTL in vitro. These molecules did not interfere with the interaction of CD8(+) T cells with their cognate targets. Rather, they inhibited lytic granule release in response both to TCR engagement and to stimuli that induce granule release in a nonpolarized manner. At the subcellular level, confocal microscopic imaging identified inhibition of polarization of lytic granules to the immunological synapse upon target cell recognition. Thus, tumor-shed gangliosides suppress lytic activity of CD8(+) T cells by a novel mechanism, that is, inhibition of trafficking of lytic granules in response to TCR engagement, as well as by interfering with the process of granule exocytosis in CD8(+) T cells.

Enhancing the Plasma-Resistance Properties of Li2O-Al2O3-SiO2 Glasses for the Semiconductor Etch Process via Alkaline Earth Oxide Incorporation.

To develop plasma-resistant glass materials suitable for semiconductor etching processes, we introduced alkaline earth oxides (ROs) into a Li2O-Al2O3-SiO2 (LAS) glass. Analysis of glass properties with respect to the additives revealed that among the analyzed materials, the LAS material in which Li2O was partially replaced by MgO (MLAS) exhibited the most favorable characteristics, including a low dielectric constant (6.3) and thermal expansion coefficient (2.302 × 10-6/°C). The high performance of MLAS is attributed to the high ionic field strength of Mg2+ ions, which restricts the movement of Li+ ions under the influence of electric fields and thermal vibrations at elevated temperatures. When exposed to CF4/O2/Ar plasma, the etching speed of RO-doped glasses decreased compared with that of quartz and LAS glass, primarily owing to the generation of a high-sublimation-point fluoride layer on the surface. Herein, MLAS demonstrated the slowest etching speed, indicating exceptional plasma resistance. X-ray photoelectron spectroscopy analysis conducted immediately after plasma etching revealed that the oxidation-to-fluorination ratio of Li was the lowest for MLAS. This observation suggests that the presence of Mg2+ ions in the plasma discharge inhibits the migration of Li+ ions toward the surface, thereby contributing to the excellent plasma resistance of MLAS.

Preparation of Remote Plasma Atomic Layer-Deposited HfO2 Thin Films with High Charge Trapping Densities and Their Application in Nonvolatile Memory Devices.

Optimization of equipment structure and process conditions is essential to obtain thin films with the required properties, such as film thickness, trapped charge density, leakage current, and memory characteristics, that ensure reliability of the corresponding device. In this study, we fabricated metal-insulator-semiconductor (MIS) structure capacitors using HfO2 thin films separately deposited by remote plasma (RP) atomic layer deposition (ALD) and direct-plasma (DP) ALD and determined the optimal process temperature by measuring the leakage current and breakdown strength as functions of process temperature. Additionally, we analyzed the effects of the plasma application method on the charge trapping properties of HfO2 thin films and properties of the interface between Si and HfO2. Subsequently, we synthesized charge-trapping memory (CTM) devices utilizing the deposited thin films as charge-trapping layers (CTLs) and evaluated their memory properties. The results indicated excellent memory window characteristics of the RP-HfO2 MIS capacitors compared to those of the DP-HfO2 MIS capacitors. Moreover, the memory characteristics of the RP-HfO2 CTM devices were outstanding as compared to those of the DP-HfO2 CTM devices. In conclusion, the methodology proposed herein can be useful for future implementations of multiple levels of charge-storage nonvolatile memories or synaptic devices that require many states.

Synthesis of Planar-Type ZnO Powder in Non-Nano Scale Dimension and Its Application in Ultraviolet Protection Cosmetics.

ZnO is one of the most widely used inorganic sunscreens, owing to its fine particle size and UV light shielding capability. However, powders at nanosizes can be toxic and cause adverse effects. The development of non-nanosized particles has been slow. The present work investigated synthesis methods of non-nanosized ZnO particles for ultraviolet protection application. By altering the starting material, KOH concentration, and input speed, the ZnO particles can be obtained in different forms, including needle type, planar type, and vertical wall type. Cosmetic samples were made by mixing different ratios of synthesized powders. The physical properties and the UV blockage efficacy of different samples were evaluated using scanning electron microscopy (SEM), X-ray diffraction (XRD), particle size analyzer (PSA), and ultraviolet/visible (UV/Vis) spectrometer. The samples with 1:1 ratio of needle-type ZnO and vertical wall-type ZnO exhibited superior light blocking effect owing to improved dispersibility and prevention of particle agglomeration. The 1:1 mixed sample also complied with the European nanomaterials regulation due to the absence of nanosized particles. With superior UV protection in the UVA and UVB regions, the 1:1 mixed powder showed potential to be used as a main ingredient in UV protection cosmetics.

Characteristics of Hf0.5Zr0.5O2 Thin Films Prepared by Direct and Remote Plasma Atomic Layer Deposition for Application to Ferroelectric Memory.

Hf0.5Zr0.5O2 (HZO) thin film exhibits ferroelectric properties and is presumed to be suitable for use in next-generation memory devices because of its compatibility with the complementary metal-oxide-semiconductor (CMOS) process. This study examined the physical and electrical properties of HZO thin films deposited by two plasma-enhanced atomic layer deposition (PEALD) methods- direct plasma atomic layer deposition (DPALD) and remote plasma atomic layer deposition (RPALD)-and the effects of plasma application on the properties of HZO thin films. The initial conditions for HZO thin film deposition, depending on the RPALD deposition temperature, were established based on previous research on HZO thin films deposited by the DPALD method. The results show that as the measurement temperature increases, the electric properties of DPALD HZO quickly deteriorate; however, the RPALD HZO thin film exhibited excellent fatigue endurance at a measurement temperature of 60 °C or less. HZO thin films deposited by the DPALD and RPALD methods exhibited relatively good remanent polarization and fatigue endurance, respectively. These results confirm the applicability of the HZO thin films deposited by the RPALD method as ferroelectric memory devices.

Diode-pumped continuous-wave eye-safe Nd:YAG laser at 1415 nm.

We describe the output performance of the 1415 nm emission in Nd:YAG in a plane-concave cavity under traditional pumping into the 4F5/2 level (808 nm) and direct in-band pumping into the 4F3/2 level (885 nm). An end-pumped Nd:YAG laser yielded maximum cw output power of 6.3 W and 4.2 W at 885 nm and 808 nm laser diode (LD) pumping, respectively. To the best of our knowledge, this is the highest output power of a LD-pumped 1415 nm laser.

Nano-scale texturing of borosilicate glasses using CF4-based plasma discharge for application in thin film solar cells.

Random plasma treatment techniques were used as a texturing method to reduce the surface reflection of glass substrates in thin film solar cells. Various gas mixtures were used for the plasma discharge in an effort to examine the texturing mechanism. Using a plasma treatment comprising CF4/O2 and CF4/Ar with a gas flow ratio of 1 to 2, the surface reflectance could be decreased to 6.83% and 6.82%, respectively. The surface treatment was very effective with the use of a low RF power of 50 W and an optimal time of 5 min. It is considered that the optical characteristics of the glass substrate are highly correlated to its surface morphology which can be produced not only through nano-scale chemical reactions with radicals but also through ion flux bombardment.

Effects of a PbTiO3 insertion layer on the morphological and electromechanical characteristics of sol-gel-driven 0.2PZN-0.8PZT piezoelectric films for energy harvesters.

This study investigated the morphological and electromechanical characteristics of 0.2PZN-0.8PZT films fabricated using a PbTiO3 layer. Crack-free 1-microm-thick films with a pure perovskite phase were obtained on Pt/Ti/SiO2/Si substrates using a modified sol-gel deposition method. A highly dense and smooth morphology and a high piezoelectric coefficient (d33) of 230 pC/N were observed in a 0.2PZN-0.8PZT film with a PbTiO3 insertion layer after annealing at 750 degrees C. The as-produced sol-gel-driven 0.2PZN-0.8PZT thin films are attractive for application to piezoelectrically operated microelectronic actuators, sensors, or energy harvesters due to their low facility cost, smooth surface, and excellent electromechanical characteristics.

Design and Preparation of Self-Oscillating Actuators Using Piezoelectric Ceramics with High Coupling Factors and Mechanical Quality Factors.

Piezoelectric material properties were optimized to develop materials for an ultrasonic vibrator targeting a high vibration efficiency. Herein, novel materials were developed using a composition represented by 0.08Pb(Ni1/3Nb2/3)O3-0.07Pb(Mn1/3Nb2/3)O3-0.85Pb(Zr0.5Ti0.5)O3 + 0.3 wt.% CuO + 0.3 wt.% Fe2O3 with 0.3 wt.% Sb2O3 doping. A ceramic shape with a thickness of 2 mm was optimized using finite element analysis software, and high values of coupling factors (0.54) and mechanical quality factors (1151) were obtained. This ceramic was used to fabricate a bio-beauty device (frequency = 1 MHz), and the manufactured ultrasonic vibrator indicated that the actuator oscillated with the maximum amplitude at a frequency of 1.06 MHz.

Development of PZN-PMN-PZT Piezoelectric Ceramics with High d33 and Qm Values.

To achieve good long-term temperature stability in devices used in energy-conversion applications, this study is aimed at developing combined ceramics, referred to as PZN-PMN-PZT, comprising Pb(Zn1/3Nb2/3)O3 (PZN) and Pb(Mn1/3Nb2/3)O3 (PMN), which are typical relaxor ferroelectric materials, and Pb(Zr,Ti)O3 (PZT). The piezoelectric properties were compared based on several parameters according to the change in the composition ratio between relaxor materials, amounts of Sb2O3 dopant, and Zr/Ti ratio in the PZT system. Finally, we established optimal poling conditions to improve the electrical properties of the optimized piezoelectric material, based on the evaluation of ceramic properties according to the applied voltage during the poling process. The optimized composition of the investigated piezoelectric ceramics is represented by 0.14PZN-0.06PMN-0.80PbZr0.49Ti0.51 + 0.3 wt.% CuO + 0.3 wt.% Fe2O3 with 0.1 wt.% Sb2O3 doping, which yielded the superior properties (d33 = 361 pC/N, Qm = 1234, Tc = 306 °C).

Effect of Process Temperature on Density and Electrical Characteristics of Hf0.5Zr0.5O2 Thin Films Prepared by Plasma-Enhanced Atomic Layer Deposition.

HfxZr1-xO2 (HZO) thin films have excellent potential for application in various devices, including ferroelectric transistors and semiconductor memories. However, such applications are hindered by the low remanent polarization (Pr) and fatigue endurance of these films. To overcome these limitations, in this study, HZO thin films were fabricated via plasma-enhanced atomic layer deposition (PEALD), and the effects of the deposition and post-annealing temperatures on the density, crystallinity, and electrical properties of the thin films were analyzed. The thin films obtained via PEALD were characterized using cross-sectional transmission electron microscopy images and energy-dispersive spectroscopy analysis. An HZO thin film deposited at 180 °C exhibited the highest o-phase proportion as well as the highest density. By contrast, mixed secondary phases were observed in a thin film deposited at 280 °C. Furthermore, a post-annealing temperature of 600 °C yielded the highest thin film density, and the highest 2Pr value and fatigue endurance were obtained for the film deposited at 180 °C and post-annealed at 600 °C. In addition, we developed three different methods to further enhance the density of the films. Consequently, an enhanced maximum density and exceptional fatigue endurance of 2.5 × 107 cycles were obtained.

Fabrication of Highly Porous and Pure Zinc Oxide Films Using Modified DC Magnetron Sputtering and Post-Oxidation.

Porous films of metals and metal oxides exhibit larger surface areas and higher reactivities than those of dense films. Therefore, they have gained growing attention as potential materials for use in various applications. This study reports the use of a modified direct current magnetron sputtering method to form porous Zn-ZnO composite films, wherein a subsequent wet post-oxidation process is employed to fabricate pure porous ZnO films. The porous Zn-ZnO composite films were initially formed in clusters, and evaluation of their resulting properties allowed the optimal conditions to be determined. An oxygen ratio of 0.3% in the argon gas flow resulted in the best porosity, while a process pressure of 14 mTorr was optimal. Following deposition, porous ZnO films were obtained through rapid thermal annealing in the presence of water vapor, and the properties and porosities of the obtained films were analyzed. An oxidation temperature of 500 °C was optimal, with an oxidation time of 5 min giving a pure ZnO film with 26% porosity. Due to the fact that the films produced using this method are highly reliable, they could be employed in applications that require large specific surface areas, such as sensors, supercapacitors, and batteries.

Preparation and Characterization of Planar-Type ZnO Powder with High Aspect Ratio for Application in Ultraviolet- and Heat-Shield Cosmetics.

In this study, a [0001]-plane planar-type ZnO ceramic powder material with a high aspect ratio ranging from 20:1-50:1 is synthesized using the electrolyte collected from zinc air battery power generation. This high aspect ratio may be due to the Zn(OH)2-4 anion dissolved in the electrolyte. The obtained planar-type ZnO exhibits excellent formulation stability and applicability, even when formulated as a cosmetic with a single inorganic ingredient. Compared to commercial ZnO or TiO2 powders, relatively better protection against infrared and ultraviolet (UV) radiation is realized due to its asymmetric characteristics, with a width of approximately 1 µm and thickness of tens of nm. The synthesized planar-type ZnO is mixed with nanosized ZnO or TiO2 commercial powders and formulated into various combinations to achieve a high UV protection rate and heat-blocking effect. In particular, the addition of planar-type ZnO to nanosized TiO2 powders increases the heat-blocking effect, and improves the applicability and formulation stability of the cosmetic formulation, despite the decrease in turbidity. Among all the ceramic powder combinations examined in this study, the best UV protection rate and heat-blocking effect are obtained when the synthesized planar-type ZnO is mixed with microsized and nanosized TiO2.

Preparation and Characterization of Sol-Gel-Driven LixLa3Zr2O12 Solid Electrolytes and LiCoO2 Cathodes for All-Solid-State Lithium-Ion Batteries.

In the current study, we prepared a LixLa3Zr2O12 ((Al, Ta) LLZO) powder doped with 0.2 mol of Al and Ta using the sol-gel method and subsequently used it to fabricate solid electrolyte pellets. In pellets with lithium content of 6.2 and 6.82 mol, a cubic phase and a lithium-deficient pyrochlore mixed-phase were respectively observed. However, when the lithium content was 8.06 mol, a lithium-excess phase was also observed. Meanwhile, at 7.44 mol lithium, the (Al, Ta) LLZO ceramic pellets showed a pure cubic garnet phase with no secondary phase. When lithium was added excessively, a non-granular morphology was observed at the (Al, Ta) LLZO fracture surface in which the grains were tightly bonded by the liquid phase formed during sintering. Nyquist plots of the pellets showed that the effect of grain boundaries was eliminated and the pellets exhibited a high lithium ion conductivity of 4.26 × 10-4 S/cm. Using spin coating and multi-step heat treatment, we deposited LiCoO2 (LCO) thin films on (Al, Ta) LLZO pellets to form cathodes. There was no significant interdiffusion between the LCO cathode and (Al, Ta) LLZO solid electrolyte and morphological analysis indicted that a thin interfacial layer (~10 nm) was formed between the LCO and the electrolyte. Finally, we demonstrated an all-solid-state rechargeable battery in the form of a coin cell comprising of an LCO cathode, Li metal anode, and (Al, Ta) LLZO solid electrolyte, which could yield a discharge capacity of ~100 mAh/g.

Fabrication of 70 nm-sized zero residual polymer patterns by thermal nanoimprint lithography.

The formation of a residual layer under the imprinted patterns is commonly observed after the imprinting process. In order to utilize the imprinted patterns into the top-down process, the removal process of the residual layer using oxygen plasma is inevitable. However, the critical dimension of the imprinted patterns can be degraded during the residual layer removal process and this degradation becomes severer for smaller sized patterns. Zero residual layer imprinting therefore has advantages in nano-sized patterning. In this study, 70 nm-narrow polymer patterns with a height of 300 nm were successfully fabricated on a Si wafer without any residual layer using a high aspect ratio template and thin polymer resin layer, after which 70 nm-narrow Cr metal nanowires were formed on the Si wafer through the lift-off process.

Publisher Correction: Pattern analysis of 532- and 1,064-nm picosecond-domain laser-induced immediate tissue reactions in ex vivo pigmented micropig skin.

An amendment to this paper has been published and can be accessed via a link at the top of the paper.