RESUMEN
The ability to manipulate crystal structures using kinetic control is of broad interest because it enables the design of materials with structures, compositions, and morphologies that may otherwise be unattainable. Herein, we report the low-temperature structural transformation of bulk inorganic crystals driven by hard-soft acid-base (HSAB) chemistry. We show that the three-dimensional framework K2Sb8Q13 and layered KSb5Q8 (Q = S, Se, and Se/S solid solutions) compounds transform to one-dimensional Sb2Q3 nano/microfibers in N2H4·H2O solution by releasing Q2- and K+ ions. At 100 °C and ambient pressure, a transformation process takes place that leads to significant structural changes in the materials, including the formation and breakage of covalent bonds between Sb and Q. Despite the insolubility of the starting crystals in N2H4·H2O under the given conditions, the mechanism of this transformation can be rationalized by applying the HSAB principle. By adjusting factors such as the reactants' acid/base properties, temperature, and pressure, the process can be controlled, allowing for the achievement of a wide range of optical band gaps (ranging from 1.14 to 1.59 eV) while maintaining the solid solution nature of the anion sublattice in the Sb2Q3 nanofibers.
RESUMEN
The core task for Mott insulators includes how rigid distributions of electrons evolve and how these induce exotic physical phenomena. However, it is highly challenging to chemically dope Mott insulators to tune properties. Herein, we report how to tailor electronic structures of the honeycomb Mott insulator RuCl3 employing a facile and reversible single-crystal to single-crystal intercalation process. The resulting product (NH4 )0.5 RuCl3 â 1.5 H2 O forms a new hybrid superlattice of alternating RuCl3 monolayers with NH4 + and H2 O molecules. Its manipulated electronic structure markedly shrinks the Mott-Hubbard gap from 1.2 to 0.7â eV. Its electrical conductivity increases by more than 103 folds. This arises from concurrently enhanced carrier concentration and mobility in contrary to the general physics rule of their inverse proportionality. We show topotactic and topochemical intercalation chemistry to control Mott insulators, escalating the prospect of discovering exotic physical phenomena.
RESUMEN
Doping and alloying are fundamental strategies to improve the thermoelectric performance of bare materials. However, identifying outstanding elements and compositions for the development of high-performance thermoelectric materials is challenging. In this study, we present a data-driven approach to improve the thermoelectric performance of SnSe compounds with various doping. Based on the newly generated experimental and computational dataset, we built highly accurate predictive models of thermoelectric properties of doped SnSe compounds. A well-designed feature vector consisting of the chemical properties of a single atom and the electronic structures of a solid plays a key role in achieving accurate predictions for unknown doping elements. Using the machine learning predictive models and calculated map of the solubility limit for each dopant, we rapidly screened high-dimensional material spaces of doped SnSe and evaluated their thermoelectric properties. This data-driven search provided overall strategies to optimize and improve the thermoelectric properties of doped SnSe compounds. In particular, we identified five dopant candidate elements (Ge, Pb, Y, Cd, and As) that provided a high ZT exceeding 2.0 and proposed a design principle for improving the ZT by Sn vacancies depending on the doping elements. Based on the search, we proposed yttrium as a new high-ZT dopant for SnSe with experimental confirmations. Our research is expected to lead to novel high-ZT thermoelectric material candidates and provide cutting-edge research strategies for materials design and extraction of design principles through data-driven research.
RESUMEN
Thermoelectric materials generate electric energy from waste heat, with conversion efficiency governed by the dimensionless figure of merit, ZT. Single-crystal tin selenide (SnSe) was discovered to exhibit a high ZT of roughly 2.2-2.6 at 913 K, but more practical and deployable polycrystal versions of the same compound suffer from much poorer overall ZT, thereby thwarting prospects for cost-effective lead-free thermoelectrics. The poor polycrystal bulk performance is attributed to traces of tin oxides covering the surface of SnSe powders, which increases thermal conductivity, reduces electrical conductivity and thereby reduces ZT. Here, we report that hole-doped SnSe polycrystalline samples with reagents carefully purified and tin oxides removed exhibit an ZT of roughly 3.1 at 783 K. Its lattice thermal conductivity is ultralow at roughly 0.07 W m-1 K-1 at 783 K, lower than the single crystals. The path to ultrahigh thermoelectric performance in polycrystalline samples is the proper removal of the deleterious thermally conductive oxides from the surface of SnSe grains. These results could open an era of high-performance practical thermoelectrics from this high-performance material.
RESUMEN
The superiority of in vitro 3D cultures over conventional 2D cell cultures is well recognized by the scientific community for its relevance in mimicking the native tissue architecture and functionality. The recent paradigm shift in the field of tissue engineering toward the development of 3D in vitro models can be realized with its myriad of applications, including drug screening, developing alternative diagnostics, and regenerative medicine. Hydrogels are considered the most suitable biomaterial for developing an in vitro model owing to their similarity in features to the extracellular microenvironment of native tissue. In this review article, recent progress in the use of hydrogel-based biomaterial for the development of 3D in vitro biomimetic tissue models is highlighted. Discussions of hydrogel sources and the latest hybrid system with different combinations of biopolymers are also presented. The hydrogel crosslinking mechanism and design consideration are summarized, followed by different types of available hydrogel module systems along with recent microfabrication technologies. We also present the latest developments in engineering hydrogel-based 3D in vitro models targeting specific tissues. Finally, we discuss the challenges surrounding current in vitro platforms and 3D models in the light of future perspectives for an improved biomimetic in vitro organ system.
Asunto(s)
Hidrogeles , Ingeniería de Tejidos , Materiales Biocompatibles , Técnicas de Cultivo de Célula , Medicina Regenerativa/métodos , Ingeniería de Tejidos/métodosRESUMEN
Extraordinary properties of traditional hyperbolic metamaterials, not found in nature, arise from their man-made subwavelength structures causing unique light-matter interactions. However, their preparation requiring nanofabrication processes is highly challenging and merely provides nanoscale two-dimensional structures. Stabilizing their bulk forms via scalable procedures has been a sought-goal for broad applications of this technology. Herein, we report a new strategy of designing and realizing bulk metamaterials with finely tunable hyperbolic responses. We develop a facile two-step process: (1) self-assembly to obtain heterostructured nanohybrids of building blocks and (2) consolidation to convert nanohybrid powders to dense bulk pellets. Our samples have centimeter-scale dimensions typically, readily further scalable. Importantly, the thickness of building blocks and their relative concentration in bulk materials serve as a delicate means of controlling hyperbolic responses. The resulting new bulk heterostructured material system consists of the alternating h-BN and graphite/graphene nanolayers and exhibits significant modulation in both type-I and type-II hyperbolic resonance modes. It is the first example of real bulk hyperbolic metamaterials, consequently displaying the capability of tuning their responses along both in-plane and out-of-plane directions of the materials for the first time. It also distinctly interacts with unpolarized and polarized transverse magnetic and electronic beams to give unique hyperbolic responses. Our achievement can be a new platform to create various bulk metamaterials without complicated nanofabrication techniques. Our facile synthesis method using common laboratory techniques can open doors to broad-range researchers for active interdisciplinary studies for this otherwise hardly accessible technology.
RESUMEN
BACKGROUND: Hemodynamic instability is a frequent adverse effect following administration of dexmedetomidine (DMED). In this study, we evaluated the incidence of DMED-induced hemodynamic instability and its predictive factors in clinical regional anesthesia practice. METHODS: One hundred sixteen patients who underwent orthopedic upper limb surgery under brachial plexus block with intravenous DMED administration were retrospectively identified. The primary outcome was the incidence of DMED-induced hemodynamic instability. The participants were allocated to a stable or unstable group by their hemodynamic instability status. Patients' characteristics were compared between the groups. The relationship between the potential risk factors and development of DMED-induced hemodynamic instability was analyzed with a logistic regression model. RESULTS: DMED-induced hemodynamic instability was observed in 14.7% of patients (17/116). The unstable group had more women than the stable group (76.5% vs. 39.4%, P = 0.010). When patients were classified into four subgroup according to body mass index (underweight, normal weight, overweight, and obesity), there was significant difference in the composition of the subgroups in the two groups (P = 0.008). In univariate analysis, female sex, obesity, and pre-existing hypertension were significant predictors of DMED-induced hemodynamic instability. Multivariate analysis demonstrated that female sex (adjusted OR 3.86, CI 1.09; 13.59, P = 0.036) and obesity (adjusted OR 6.41, CI 1.22; 33.57, P = 0.028) were independent predictors of DMED-induced hemodynamic instability. CONCLUSIONS: Female and obese patients are more likely to have hemodynamic instability following intravenous DMED administration in clinical regional anesthesia practice. This study suggests that DMED dose may be diminished to prevent hypotensive risk in these populations. TRIAL REGISTRATION: This article was retrospectively registered at WHO clinical trial registry platform (Trial number: KCT0005977 ).
Asunto(s)
Bloqueo del Plexo Braquial/métodos , Dexmedetomidina/efectos adversos , Hemodinámica/efectos de los fármacos , Hipnóticos y Sedantes/efectos adversos , Procedimientos Ortopédicos/métodos , Extremidad Superior/cirugía , Adulto , Anciano , Femenino , Humanos , Masculino , Persona de Mediana Edad , Obesidad/complicaciones , Obesidad/fisiopatología , República de Corea , Estudios Retrospectivos , Factores SexualesRESUMEN
Retinal pigment epithelium (RPE) is a monolayer of the pigmented cells that lies on the thin extracellular matrix called Bruch's membrane. This monolayer is the main component of the outer blood-retinal barrier (BRB), which plays a multifunctional role. Due to their crucial roles, the damage of this epithelium causes a wide range of diseases related to retinal degeneration including age-related macular degeneration, retinitis pigmentosa, and Stargardt disease. Unfortunately, there is presently no cure for these diseases. Clinically implantable RPE for humans is under development, and there is no practical examination platform for drug development. Here, we developed porcine Bruch's membrane-derived bioink (BM-ECM). Compared to conventional laminin, the RPE cells on BM-ECM showed enhanced functionality of RPE. Furthermore, we developed the Bruch's membrane-mimetic substrate (BMS) via the integration of BM-ECM and 3D printing technology, which revealed structure and extracellular matrix components similar to those of natural Bruch's membrane. The developed BMS facilitated the appropriate functions of RPE, including barrier and clearance functions, the secretion of anti-angiogenic growth factors, and enzyme formation for phototransduction. Moreover, it could be used as a basement frame for RPE transplantation. We established BMS using 3D printing technology to grow RPE cells with functions that could be used for an in vitro model and RPE transplantation.
Asunto(s)
Biomimética , Lámina Basal de la Coroides/citología , Degeneración Macular/patología , Impresión Tridimensional , Epitelio Pigmentado de la Retina/citología , Inhibidores de la Angiogénesis/farmacología , Animales , Adhesión Celular , Proliferación Celular , Modelos Animales de Enfermedad , Matriz Extracelular/metabolismo , Técnicas In Vitro , Microvellosidades , Fagocitosis , Ratas , Reología , PorcinosRESUMEN
BACKGROUND: Increased oxidative stress in end-stage renal disease is regarded as one of the important mechanisms in the atherosclerosis and muscle wasting. However, studies examining the clinical significance of oxidative stress by direct measurement of these markers and its association with volume status and sarcopenia are limited. METHODS: A follow-up cross-sectional study was performed in stable hemodialysis (HD) patients and serum protein carbonyl levels were measured as a biomarker of oxidative stress. Additionally, multi-frequency body composition analysis, handgrip strength (HGS) and nutritional assessments were performed at baseline. RESULTS: Eighty-eight patients undergoing HD were included and 30 (34.1%) patients died during a mean follow-up of 5.2 years. The mean patient age was 60.6 ± 13.5 years, and the mean HD duration was 50.8 ± 41.3 months. In total, 16 patients (18.2%) were overhydrated, 49 (55.7%) had low HGS and 36 (40.9%) had low muscle mass. Serum protein carbonyl levels were associated with serum levels of albumin, prealbumin and transferrin, hydration status and low HGS. Overhydration (odds ratio [OR] 7.01, 95% CI 1.77-27.79, p = 0.006), prealbumin (OR 0.91, 95% CI 0.83-0.99, p = 0.030), subjective global assessment (OR 3.52, 95% CI 1.08-11.46, p = 0.037) and sarcopenia (OR 3.41, 95% CI 1.02-11.32, p = 0.046) were significantly related to increased serum protein carbonyl levels. Multivariate analysis showed that the serum levels of protein carbonyl (Hazard ratio [HR] 2.37, 95% CI 1.02-5.55, p = 0.036), albumin (HR 0.17, 95% CI 0.06-0.46, p = 0.003), prealbumin (HR 0.86, 95% CI 0.80-0.92, p = 0.001), overhydration (HR 2.31, 95% CI 1.26-8.71, p = 0.015) and sarcopenia (HR 2.72, 95% CI 1.11-6.63, p = 0.028) were independent determinants of all-cause mortality. CONCLUSIONS: Serum protein carbonyl was significantly associated with overhydration, nutritional status and sarcopenia, and could be a new predictor of mortality in patients undergoing HD.
Asunto(s)
Fuerza de la Mano , Fallo Renal Crónico/metabolismo , Mortalidad , Estrés Oxidativo , Carbonilación Proteica , Sarcopenia/metabolismo , Albúmina Sérica/metabolismo , Transferrina/metabolismo , Desequilibrio Hidroelectrolítico/metabolismo , Anciano , Composición Corporal , Estudios Transversales , Femenino , Estudios de Seguimiento , Humanos , Fallo Renal Crónico/complicaciones , Fallo Renal Crónico/terapia , Masculino , Persona de Mediana Edad , Estado Nutricional , Oportunidad Relativa , Prealbúmina/metabolismo , Modelos de Riesgos Proporcionales , Diálisis Renal , Sarcopenia/complicaciones , Sarcopenia/fisiopatología , Desequilibrio Hidroelectrolítico/complicacionesRESUMEN
High electron mobility transistors (HEMTs) and Schottky barrier diodes (SBDs) based on AlGaN/GaN heterostructure have been widely studied for high-frequency and/or high-power application. Widely distributed substrates for the high performance of RF applications are presently AlGaN/GaN on SiC, and those for high power performance are AlGaN/GaN on Si. Because the thermal conductivity of CVD diamond substrates is as high as 12 W/cm · K, devices on AlGaN/GaN on CVD diamond are one of the excellent alternatives for power and RF applications. In comparison, the thermal conductivity of AlGaN/GaN on SiC is 4.9 W/cm K, and that of AlGaN/GaN on Si is 1.3 W/cm · K. In this work, we report the fabrication of SBD devices with 163.8 mm Schottky channel length. We also compared the thermal properties of the fabricated large scale SBD devices on different substrates.
RESUMEN
BACKGROUND: Although higher body mass index (BMI) is associated with better survival in patients undergoing dialysis, BMI is not an adequate obesity indicator. We hypothesized that the fat-to-lean (F/L) mass ratio could be a suitable marker of nutritional status and evaluated its prognostic impact on long-term outcomes in patients undergoing hemodialysis (HD). METHODS: In total, 131 patients undergoing HD were recruited and monitored prospectively for up to 5 years. Body composition was analyzed, and other nutritional and inflammatory parameters were measured. RESULTS: The mean age of the cohort was 60.7 ± 13.6 years, and 65 patients were diabetic. Age, sex, diabetes, comorbidity, and inflammation were associated significantly with the F/L mass ratio. During the follow-up period, 21 patients experienced cardiac events and 22 patients died. Patients with higher F/L mass ratios had significantly higher risks of all-cause death (hazard ratio [HR] 3.61, 95% CI 1.07-12.13; p = 0.038) and cardiac events (HR 3.54, 95% CI 1.05-11.94; p = 0.041) than those with lower F/L mass ratios. CONCLUSIONS: The F/L mass ratio was a useful surrogate marker of nutritional and inflammatory status, and an independent predictor of cardiac events and all-cause mortality, in patients undergoing HD.
Asunto(s)
Composición Corporal , Enfermedades Cardiovasculares/epidemiología , Diálisis Renal/mortalidad , Anciano , Índice de Masa Corporal , Enfermedades Cardiovasculares/mortalidad , Causas de Muerte , Estudios de Cohortes , Femenino , Humanos , Masculino , Persona de Mediana Edad , Estado Nutricional , Estudios ProspectivosRESUMEN
The liver is an important organ and plays major roles in the human body. Because of the lack of liver donors after liver failure and drug-induced liver injury, much research has focused on developing liver alternatives and liver in vitro models for transplantation and drug screening. Although numerous studies have been conducted, these systems cannot faithfully mimic the complexity of the liver. Recently, three-dimensional (3D) cell printing technology has emerged as one of a number of innovative technologies that may help to overcome this limitation. However, a great deal of work in developing biomaterials optimized for 3D cell printing-based liver tissue engineering remains. Therefore, in this work, we developed a liver decellularized extracellular matrix (dECM) bioink for 3D cell printing applications and evaluated its characteristics. The liver dECM bioink retained the major ECM components of the liver while cellular components were effectively removed and further exhibited suitable and adjustable properties for 3D cell printing. We further studied printing parameters with the liver dECM bioink to verify the versatility and fidelity of the printing process. Stem cell differentiation and HepG2 cell functions in the liver dECM bioink in comparison to those of commercial collagen bioink were also evaluated, and the liver dECM bioink was found to induce stem cell differentiation and enhance HepG2 cell function. Consequently, the results demonstrate that the proposed liver dECM bioink is a promising bioink candidate for 3D cell printing-based liver tissue engineering.
Asunto(s)
Bioimpresión/métodos , Matriz Extracelular/metabolismo , Hígado/citología , Impresión Tridimensional , Ingeniería de Tejidos/métodos , Animales , Materiales Biocompatibles/química , Células de la Médula Ósea/citología , Diferenciación Celular , Supervivencia Celular , Colágeno/química , Células Hep G2 , Humanos , Células Madre Mesenquimatosas/citología , Porcinos , Andamios del Tejido/químicaRESUMEN
A linearized wavelength-swept thermo-optic laser chip was applied to demonstrate a fiber Bragg grating (FBG) sensor interrogation system. A broad tuning range of 11.8 nm was periodically obtained from the laser chip for a sweep rate of 16 Hz. To measure the linear time response of the reflection signal from the FBG sensor, a programmed driving signal was directly applied to the wavelength-swept laser chip. The linear wavelength response of the applied strain was clearly extracted with an R-squared value of 0.99994. To test the feasibility of the system for dynamic measurements, the dynamic strain was successfully interrogated with a repetition rate of 0.2 Hz by using this FBG sensor interrogation system.
RESUMEN
AIGaN/GaN nanowire (NW) FETs with a channel width down to -300 nm has been fabricated by "top-down" approach by using electron-beam lithography process. The fabricated AIGaN/GaN NW FETs showed the minimum threshold voltage -3 V, the gate leakage current -10(-10) A/mm, and the maximum transconductance -216 mS/mm, respectively. It has also been demonstrated that the gate controllability of the AIGaN/GaN FETs is improved with decreasing channel width. In the fabricated devices the threshold voltage V(th) for the NW FETs with a width of -300 nm shows a positive shift (deltaV(th) = 2.5 V) with respect to that of the reference FETs. This can be attributed the change in carrier density of the two dimensional electron gas generated at the interface of an AlGaN/GaN.
RESUMEN
Given that current television programming contains numerous gambling portrayals, it is imperative to understand whether and to what extent these gambling behaviors in media influence individuals' beliefs, attitudes, and intentions. This study explores an extended model of the theory of reasoned action (TRA) by including gambling media exposure as a distal, mediating and mediated factor in predicting undergraduate students' intentions to gamble in a casino. Findings show that the extended model of TRA clearly indicates that the constructs of gambling media exposure, prior gambling experience, and level of gambling addiction contribute to the prediction of undergraduate students' casino gambling intentions. Theoretical implications of gambling media effects and practical implications for public policy are discussed, and future research directions are outlined.
Asunto(s)
Juego de Azar/psicología , Intención , Estudiantes/psicología , Adolescente , Adulto , Actitud , Femenino , Humanos , Masculino , Medios de Comunicación de Masas , Modelos Psicológicos , Teoría Psicológica , Estudiantes/estadística & datos numéricos , Adulto JovenRESUMEN
In the last decade, organoids have gained popularity for developing mini-organs to support advancements in the study of organogenesis, disease modeling, and drug screening and, subsequently, in the development of new therapies. To date, such cultures have been used to replicate the composition and functionality of organs such as the kidney, liver, brain, and pancreas. However, depending on the experimenter, the culture environment and cell conditions may slightly vary, resulting in different organoids; this factor significantly affects their application in new drug development, especially during quantification. Standardization in this context can be achieved using bioprinting technology-an advanced technology that can print various cells and biomaterials at desired locations. This technology offers numerous advantages, including the manufacturing of complex three-dimensional biological structures. Therefore, in addition to the standardization of organoids, bioprinting technology in organoid engineering can facilitate automation in the fabrication process as well as a closer mimicry of native organs. Further, artificial intelligence (AI) has currently emerged as an effective tool to monitor and control the quality of final developed objects. Thus, organoids, bioprinting technology, and AI can be combined to obtain high-quality in vitro models for multiple applications.
RESUMEN
Several studies have attempted to develop complex cardiovascular models, but the use of multiple cell types and poor cell alignments after fabrication have limited the practical application of these models. Among various bioprinting methods, extrusion-based bioprinting is the most widely used in the bioengineering field. This method not only has the potential to construct complex 3D biological structures but it also enables the alignment of cells in the printing direction owing to the application of shear stress to the cells during the printing process. Therefore, this study developed an in vitro cardiovascular model using an extrusion-based bioprinting method that utilizes a rotating rod as a printing platform. The rotating rod was made of polyvinyl alcohol (PVA) and used as a sacrificial rod. This rotating platform approach enabled the printing of longer tubular-vascular structures of multiple shapes, including disease models, and the water-soluble properties of PVA facilitated the isolation of the printed vascular models. In addition, this method enabled the printing of the endothelial cells in the bloodstream direction and smooth muscle cells in the circumferential direction to better mimic the anatomy of real blood vessels. Consequently, a cardiovascular model was successfully printed using a gelatin methacryloyl bioink with cells. In conclusion, the proposed fabrication method can facilitate the fabrication of various cardiovascular models that mimic the alignment of real blood vessels.
RESUMEN
In the last two decades, significant progress has been made in the development of more physiologically relevant organ-on-a-chip (OOC) systems that can mimic tissue microenvironments. Despite the advantages of these microphysiological systems, such as portability, ability to mimic physiological flow conditions, and reduction of the number of reagents required for preparation and detection, they lack real-time analyte detection with high accuracy. To address this limitation, biosensor technologies have been integrated with OOC systems to facilitate simultaneous analysis of different analytes with a single device. However, the integration of biosensors with OOC systems is challenging because of the competing demands of low-cost, simple fabrication processes and speed. In this study, we fabricate a glucose-sensing device and integrate it with a liver-on-a-chip (LOC) platform. A carbon black-polylactic acid-based three-electrode system was printed using fused deposit molding 3D printing technology to simplify the fabrication process. The sensitivity of the fabricated glucose biosensing device was enhanced by coating the electrodes with multi-walled carbon nanotubes. A biosensing integration study performed using a perfusion-based LOC demonstrated the stability, biocompatibility, and sensitivity of the proposed glucose sensing device. Furthermore, drug-toxicity studies conducted using the LOC platform demonstrated the ability of the device to detect a broad range of glucose concentrations and its enhanced sensitivity.
Asunto(s)
Técnicas Biosensibles , Nanotubos de Carbono , Glucosa/análisis , Hígado , Impresión Tridimensional , Dispositivos Laboratorio en un ChipRESUMEN
Leveraging three-dimensional (3D) bioprinting in the fields of tissue engineering and regenerative medicine has rapidly accelerated progress toward the development of living tissue constructs and biomedical devices. Ongoing vigorous research has pursued the development of 3D in vitro tissue models to replicate the key aspects of human physiology by incorporating relevant cell populations and adequate environmental cues. Given their advantages of being able to intimately mimic the heterogeneity and complexity of their native counterparts, 3D in vitro models hold promise as alternatives to conventional cell cultures or animal models for translational application to model human physiology/pathology and drug screening. Research has highlighted the importance of in vitro models, and a sophisticated biomanufacturing strategy is vitally required. In particular, vascularization is critical for the prolonged survival and functional maturation of the engineered tissues, which has remained one of the major challenges in the establishment of physiologically relevant 3D in vitro models. To this end, 3D bioprinting can efficiently generate solid and reproducible vascularized tissue models with high architectural and compositional similarity to the native tissues, leading to improve the structural maturation and tissue-specific functionality. Multiple bioprinting strategies have been developed to vascularize in vitro tissues by spatially controlled patterning of vascular precursors or generating readily perfusable vascular structures. This review presents an overview of the advanced 3D bioprinting strategies for vascularized tissue model development. We present the key elements for rebuilding functional vasculature in 3D-bioprinted tissue models and discuss the recent achievements in the engineering of 3D vascularized in vitro models using 3D bioprinting. Finally, we delineate the current challenges and future outlooks of 3D bioprinting-based vascularized tissue models.
RESUMEN
Hepatic sinusoids are uniquely organized structures that help maintain a spectrum of hepatic functions. Although several in vitro liver models have been developed to replicate liver sinusoids, most of these platforms require complex, multi-step fabrication methods making it difficult to achieve truly three-dimensional (3D) channel geometries. In this study, a single-step bioprinting technique was demonstrated to simultaneously print a chip platform and develop a perfusable vascularized liver sinusoid in vitro model. The integrated system uses a co-axial-based bioprinting approach to develop a liver sinusoid-like model that consists of a sacrificial core compartment containing a perfusable pre-vascular structure and an alginate-collagen-based shell compartment containing hepatocytes. The lumen-based perfusable 3D liver sinusoid-on-a-chip (LSOC-P) demonstrated significantly better hepatocyte viability, proliferation, and liver-specific gene and protein expression compared to a 3D hepatocyte-based core/shell model with static media and the standard hepatocyte-based 2D sandwich culture system. A drug toxicity evaluation of hepatotoxins highlighted the comparatively higher sensitivity of the LSOC system with a close estimation of the therapeutic range of safe drug concentrations for humans. In conclusion, the current findings indicate that the combinatorial single-step co-axial bioprinting technique is a promising fabrication approach for the development of a perfusable LSOC platform for drug screening applications.