Strain induced atomic structure at the Ir-doped LaAlO3/SrTiO3 interface.

The structure of Ir-doped LaAlO3/SrTiO3(001) interfaces was investigated on the atomic scale using probe-corrected transmission electron microscopy in high-angle annular dark-field scanning mode (HAADF-STEM) and electron energy loss spectroscopy (EELS), combined with first-principles calculations. We report the evolution of the strain state experimentally measured in a 5 unit-cell thick LaAlO3 film as a function of the Ir concentration in the topmost SrTiO3 layer. It is shown that the LaAlO3 layers remain fully elastically strained up to 3% of Ir doping, whereas a higher doping level seems to promote strain relaxation through enhanced cationic interdiffusion. The observed differences between the energy loss near edge structure (ELNES) of Ti-L2,3 and O-K edges at non-doped and Ir-doped interfaces are consistent with the location of the Ir dopants at the interface, up to 3% of Ir doping. These findings, supported by the results of density functional theory (DFT) calculations, provide strong evidence that the effect of dopant concentrations on the properties of this kind of interface should not be analyzed without obtaining essential information from the fine structural and chemical analysis of the grown structures.

Spin-filter tunnel junction with matched fermi surfaces.

Efficient injection of spin-polarized current into a semiconductor is a basic prerequisite for building semiconductor-based spintronic devices. Here, we use inelastic electron tunneling spectroscopy to show that the efficiency of spin-filter-type spin injectors is limited by spin scattering of the tunneling electrons. By matching the Fermi-surface shapes of the current injection source and target electrode material, spin injection efficiency can be significantly increased in epitaxial ferromagnetic insulator tunnel junctions. Our results demonstrate that not only structural but also Fermi-surface matching is important to suppress scattering processes in spintronic devices.

Local switching of two-dimensional superconductivity using the ferroelectric field effect.

Correlated oxides display a variety of extraordinary physical properties including high-temperature superconductivity and colossal magnetoresistance. In these materials, strong electronic correlations often lead to competing ground states that are sensitive to many parameters--in particular the doping level--so that complex phase diagrams are observed. A flexible way to explore the role of doping is to tune the electron or hole concentration with electric fields, as is done in standard semiconductor field effect transistors. Here we demonstrate a model oxide system based on high-quality heterostructures in which the ferroelectric field effect approach can be studied. We use a single-crystal film of the perovskite superconductor Nb-doped SrTiO3 as the superconducting channel and ferroelectric Pb(Zr,Ti)O3 as the gate oxide. Atomic force microscopy is used to locally reverse the ferroelectric polarization, thus inducing large resistivity and carrier modulations, resulting in a clear shift in the superconducting critical temperature. Field-induced switching from the normal state to the (zero resistance) superconducting state was achieved at a well-defined temperature. This unique system could lead to a field of research in which devices are realized by locally defining in the same material superconducting and normal regions with 'perfect' interfaces, the interface being purely electronic. Using this approach, one could potentially design one-dimensional superconducting wires, superconducting rings and junctions, superconducting quantum interference devices (SQUIDs) or arrays of pinning centres.

Pulsed laser deposition with rapid beam deflection by a galvanometer mirror scanner.

A pulsed laser deposition system with rapid beam deflection (RBD-PLD) by a galvanometer mirror scanner has been developed for alternating ablation of multiple targets with a single laser instrument. In this system, the alternating deposition of different target materials is carried out by scanning the laser beam between the positionally fixed targets with a galvanometer mirror instead of mechanically switching the target positions on a fixed optical path of the laser beam as is done in conventional pulsed laser deposition (PLD) systems. Thus, the "wait" time required for switching target materials to be deposited, which typically takes several seconds in a conventional system, can be made as short as a few milliseconds. We demonstrate some of the advantages of this PLD system in several technologically important aspects of thin film synthesis: (1) fast fabrication of binary alloy films, (2) preparation of natural composition spread libraries, (3) effect of the target switching time on the deposition of volatile compounds, (4) control of the degree of mixing of two different materials in a film, and (5) efficient growth of compositionally graded thin films.

In situ photoemission study of Pr1-xCaxMnO3 epitaxial thin films with suppressed charge fluctuations.

We have performed an in situ photoemission study of Pr1-xCaxMnO3 (PCMO) thin films grown on LaAlO3 (001) substrates and observed the effect of epitaxial strain on the electronic structure. We found that the chemical potential shifted monotonically with doping, unlike bulk PCMO, implying the disappearance of incommensurate charge fluctuations of bulk PCMO. In the valence-band spectra, we found a doping-induced energy shift toward the Fermi level (EF) but there was no spectral weight transfer, which was observed in bulk PCMO. The gap at EF was clearly seen in the experimental band dispersions determined by angle-resolved photoemission spectroscopy and could not be explained by the metallic band structure of the C-type antiferromagnetic state, probably due to localization of electrons along the ferromagnetic chain direction or due to another type of spin-orbital ordering.

Photoemission from buried interfaces in SrTiO3/LaTiO3 superlattices.

We have measured photoemission spectra of SrTiO3/LaTiO3 superlattices with a topmost SrTiO3 layer of variable thickness. A finite coherent spectral weight with a clear Fermi cutoff was observed at chemically abrupt SrTiO3/LaTiO3 interfaces, indicating that an "electronic reconstruction" occurs at the interface between the Mott insulator LaTiO3 and the band insulator SrTiO3. For SrTiO3/LaTiO3 interfaces annealed at high temperatures (approximately 1000 degrees C), which leads to Sr/La atomic interdiffusion and hence to the formation of La(1-x)Sr(x)TiO3-like material, the intensity of the incoherent part was found to be dramatically reduced whereas the coherent part with a sharp Fermi cutoff was enhanced due to the spread of charge. These important experimental features are well reproduced by layer dynamical-mean-field-theory calculation.

Nature of the well screened state in hard X-ray Mn 2p core-level photoemission measurements of La1-xSrxMnO3 films.

Using hard x-ray (HX; hnu=5.95 keV) synchrotron photoemission spectroscopy (PES), we study the intrinsic electronic structure of La(1-x)Sr(x)MnO(3) (LSMO) thin films. Comparison of Mn 2p core-levels with soft x-ray (SX; hnu approximately 1000 eV) PES shows a clear additional well-screened feature only in HX PES. Takeoff-angle dependent data indicate its bulk (> or =20 A) character. The doping and temperature dependence track the ferromagnetism and metallicity of the LSMO series. Cluster model calculations including charge transfer from doping-induced states show good agreement, confirming this picture of bulk properties reflected in Mn 2p core-levels using HX PES.